Age | Commit message (Collapse) | Author | Files | Lines |
|
[why]
Remove the need to include dc_link.h separately. dc.h should contain
everything needed on DM side.
[How]
Merge dc_link.h into dc.h and dc_types.h so DM only needs to include
dc.h to use all link public functions.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
PSR-SU Rate Control - or PSR-SU-RC - enables PSR-SU panels to work with
variable refresh rate to allow for more power savings. Lowering the
refresh rate can increase PSR residency by expanding the eDP main link
shut down duration. It can also lower panel power consumption.
There is a complication with PSR, since the eDP main link can be shut
down. Therefore, the timing controller (TCON) on the eDP sink nees to be
able to scan out its remote buffer independent of the main link. To
allow the eDP source to specify the sink's refresh rate while the link
is off, vendor-specific DPCD registers are used. This allows the eDP
source to then "Rate Control" the panel during PSR active.
[How]
Add DC support to communicate with PSR-SU-RC supported eDP sinks. The
sink will need to know the desired VTotal during PSR active.
This change only adds support to DC, support in amdgpu_dm is still
pending to enable this fully.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
To support PSR2 Source DPCD configuration
[How]
Update the PSR2 Source DPCD settings while the PSR2 enabled
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
Add USBC connector ID to align with new VBIOS parsing.
Add seperate DCN321 link encoder due to different PHY version affecting
DP ALT related registers.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Factor set dp lane settings to link_hwss.
v2: fix statement with no effect warning (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
DCN guard is not necessary for DP2.x relevant logic.
Drop them.
v2: squash in fix for misplaced #endif (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
When there are more DP2.0 RXs connected than the number HPO DP link
encoders we have, we need to dynamically allocate HPO DP link encoder to
the port that needs it.
[how]
Only allocate HPO DP link encoder when it is needed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Incorrect encoder assignments were being used while applying a new state
to hardware.
(1) When committing a new state to hardware requires resetting the
back-end, the encoder assignments of the current or old state should be
used when disabling the back-end; and the encoder assignments for the
next or new state should be used when re-enabling the back-end.
(2) Link training on hot plug could take over an encoder already in use
by another stream without first disabling it.
[How]
(1) Introduce a resource context 'link_enc_cfg_context' which includes:
- a mode to indicate when transitioning from current to next state.
- transient encoder assignments to use during this state transition.
Update the encoder configuration interface to respond to queries about
encoder assignment based on the mode of operation.
(2) Check if an encoder is already in use before attempting to perform
link training on hot plug.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Trying to enable multiple displays simultaneously exposed shortcomings
with the algorithm for dynamic link encoder assignment.
The main problems were:
- Assuming stream order remained constant across states would sometimes
lead to invalid DIG encoder assignment.
- Incorrect logic for deciding whether or not a DIG could support a
stream would also sometimes lead to invalid DIG encoder assignment.
- Changes in encoder assignment were wholesale while updating of the
pipe backend is incremental. This would lead to the hardware state not
matching the software state even with valid encoder assignments.
[How]
The following changes fix the identified problems.
- Use stream pointer rather than stream index to track streams across
states.
- Fix DIG compatibility check by examining the link signal type rather
than the stream signal type.
- Modify assignment algorithm to make incremental updates so software
and hardware states remain coherent.
Additionally:
- Add assertions and an encoder assignment validation function
link_enc_cfg_validate() to detect potential problems with encoder
assignment closer to their root cause.
- Reduce the frequency with which the assignment algorithm is executed.
It should not be necessary for fast state validation.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Parse DP2 encoder caps and hpo instance from bios
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
HW Blocks:
+--------+ +-----+ +------+
| OPTC | | HDA | | HUBP |
+--------+ +-----+ +------+
| | |
| | |
HPO ====|==========|========|====
| | v |
| | +-----+ |
| | | APG | |
| | +-----+ |
| | | |
| v v v
| +---------------------+
| | HPO Stream Encoder |
| +---------------------+
| |
| v
| +--------------------+
| | HPO Link Encoder |
v +--------------------+
[squash in warning fixes - Alex]
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for the DIO (Display IO) block of DCN3.1 which controls
legacy HDMI/DP stream/link encoding.
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Includes some updates to core logic for link encoder assignment and
future support for new high bandwidth output.
v2: squash in unused variable fix (Alex)
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Some display endpoints may be programmably mapped to compatible link
encoders. The assignment of link encoders to links has to be dynamic to
accommodate the increased flexibility in comparison to conventional
display endpoints.
[How]
- Add link encoder assignment tracking variables.
- Execute link encoder assignment algorithm before enabling link and
release link encoders from links once they are disabled.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
So we can track VSC SDP errors from display
[how]
Define the bit, and use it in driver logic
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DCN2 and DSC are stable enough to be build by default. So drop the flags.
[How]
Remove them using the unifdef tool. The following commands were executed
in sequence:
$ find -name '*.c' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
$ find -name '*.h' -exec unifdef -m -DCONFIG_DRM_AMD_DC_DSC_SUPPORT -DCONFIG_DRM_AMD_DC_DCN2_0 -UCONFIG_TRIM_DRM_AMD_DC_DCN2_0 '{}' ';'
In addition:
* Remove from kconfig, and replace any dependencies with DCN1_0.
* Remove from any makefiles.
* Fix and cleanup NV defninitions in dal_asic_id.h
* Expand DCN1 ifdef to include DCN2 code in the following files:
* clk_mgr/clk_mgr.c: dc_clk_mgr_create()
* core/dc_resources.c: dc_create_resource_pool()
* dce/dce_dmcu.c: dcn20_*lock_phy()
* dce/dce_dmcu.c: dcn20_funcs
* dce/dce_dmcu.c: dcn20_dmcu_create()
* gpio/hw_factory.c: dal_hw_factory_init()
* gpio/hw_translate.c: dal_hw_translate_init()
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For debug purpose, we need to check the following hardware status
in DTN log debugfs:
1.dpp & hubp clock enable;
2.crtc blank enable;
3.link phy status;
[How]
Add the upper information in the amdgpu_dm_dtn_log debugfs.
For CRTC blanked status, since DCN2 and greater reports it on the OPP
instead of OTG, we patch it in after calling optc1_read_otg_states.
Ideally, this should be done in the DCN version specific function hooks.
It has been left as a TODO item.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Type-c PHY config is not align with dpcd lane count.
When those values didn't match, it cause driver do
link training with 4 lane but phy only can output 2 lane.
The link trainig always fail.
[How]
1. Modify get_max_link_cap function. According DPALT_DP4
to update max lane count.
2. Add dp_mst_verify_link_cap to handle MST case because
we didn't call dp_mst_verify_link_cap for MST case.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
OS will reserve HW state in UEFI mode.
Driver init_hw reset to RGB which caused HDMI green in YCbCr mode.
read HW blank_color based on acc_mode.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why and How]
We want to change where timing is done for alt mode.
Some of the commented out #ifs are needed for DCN20
so we enable them for that case.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for DCN2 DSC (Display Stream Compression)
HW Blocks:
+--------++------+ +----------+
| HUBBUB || HUBP | <-- | MMHUBBUB |
+--------++------+ +----------+
| ^
v |
+--------+ +--------+
| DPP | | DWB |
+--------+ +--------+
|
v ^
+--------+ |
| MPC | |
+--------+ |
| |
v |
+-------+ +-------+ |
| OPP | <--> | DSC | |
+-------+ +-------+ |
| |
v |
+--------+ /
| OPTC | --------------
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
v2: rebase (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add support for the DIO (Display IO) block of DCN2, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Emulating passive dongle on USB-C port causes issue on some asics.
[How]
Check for DP_IS_USB_C flag in bios parser and propagate it to
encoder features flags. If DP_IS_USB_C flag is set and it is trying to
emulate passive dongle, then return fail.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Need to figure out whether a timing we want to commit matches
something that GOP already programmed, in which case
we can decide to some optimizations
[How]
1. Add way to check for DIG FE
2. Add way to check for matching OTG timing
3. Add way to check for matching pixel clock (if possible)
- Currently only support DP for pixel clock, since it is easy to calc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Need separate feature flag for DP 4:2:0 support, since existing
flag is used for HDMI
[How]
Added dp_ycbcr420_supported to struct encoder_feature_support
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
All ASICS we support has YCbCr support, so
the check is unnecessary, the currently logic
in validate output also returns true all
the time, so the unneccessary logic is removed
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This adds support for LVDS displays.
v2: add support for spread spectrum, sink detect
v3: clean up enable_lvds_output
v4: fix up link_detect
v5: remove assert on 888 format
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=105880
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Linux doesn't know lid state, better to check dig enable
value from register.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This makes the check for HDMI and dual-link DVI a bit more
straightforward.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Linux 4.15-rc4
Daniel requested it to fix some messy conflicts.
|
|
dc_link is at a higher level than link_encoder, and we only want
higher-level components to be able to access lower-level ones,
not the other way around.
Signed-off-by: Andrew Jiang <Andrew.Jiang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
These files were missing it before.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
A recent commit moved the backlight control code along with the register
defines, but did not move the power control code. This along with
remnant fields in the dce110_link_enc_registers struct made it so that
the code still compiled, but any attempts to access the
LVTMA_PWRSEQ_STATE register led to reading from an address of 0. This
patch corrects that.
Also, rename blacklight_control to edp_backlight_control (Typo fix).
Signed-off-by: Andrew Jiang <Andrew.Jiang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Yue Hin Lau <Yuehin.Lau@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
find -name Makefile -o -name Kconfig -o -name "*.c" -o -name "*.h" \
-o -name "*.cpp" -o -name "*.hpp" | \
xargs sed -i 's/struct dc_stream/struct dc_stream_state/g'
find -name Makefile -o -name Kconfig -o -name "*.c" -o -name "*.h" \
-o -name "*.cpp" -o -name "*.hpp" | \
xargs sed -i 's/struct dc_stream_state_update/struct dc_stream_update/g'
find -name Makefile -o -name Kconfig -o -name "*.c" -o -name "*.h" \
-o -name "*.cpp" -o -name "*.hpp" | \
xargs sed -i 's/struct dc_stream_state_status/struct dc_stream_status/g'
Plus some manual changes
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Stateless streams validations (not require resource population)
moved into hook to be called directly from DM.
Call dc_validate_stream be before validate_with_context for
non Linux APIs
Signed-off-by: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
dce_clocks
Signed-off-by: Amy Zhang <Amy.Zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- Move PSR programming from link encoder to dmcu
Signed-off-by: Amy Zhang <Amy.Zhang@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- remove unnecessary feature flags
- remove wireless and VGA validation
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Supported DCE versions: 8.0, 10.0, 11.0, 11.2
v2: rebase against 4.11
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|