| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Current shunt LSB values got reversed during in the
original driver commit.
So, correct the current shunt LSB values according to
the datasheet.
This caused reading slightly skewed current values.
Fixes: fff7b8ab2255 ("hwmon: add Texas Instruments TPS23861 driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210609220728.499879-3-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TPS23861 has a configuration bit for setting of the
current shunt value used on the board.
Its bit 0 of the General Mask 1 register.
According to the datasheet bit values are:
0 for 255 mOhm (Default)
1 for 250 mOhm
So, configure the bit before registering the hwmon
device according to the value passed in the DTS or
default one if none is passed.
This caused potentially reading slightly skewed values
due to max current value being 1.02A when 250mOhm shunt
is used instead of 1.0A when 255mOhm is used.
Fixes: fff7b8ab2255 ("hwmon: add Texas Instruments TPS23861 driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210609220728.499879-2-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Define the max register address the device supports.
This allows reading the whole register space via
regmap debugfs, without it only register 0x0 is visible.
This was forgotten in the original driver commit.
Fixes: fff7b8ab2255 ("hwmon: add Texas Instruments TPS23861 driver")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210609220728.499879-1-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The scpi hwmon shows the sub-zero temperature in an unsigned integer,
which would confuse the users when the machine works in low temperature
environment. This shows the sub-zero temperature in an signed value and
users can get it properly from sensors.
Signed-off-by: Riwen Lu <luriwen@kylinos.cn>
Tested-by: Xin Chen <chenxin@kylinos.cn>
Link: https://lore.kernel.org/r/20210604030959.736379-1-luriwen@kylinos.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
During standby some PSUs turn off the microcontroller. A re-init is
required during resume or the microcontroller stays unresponsive.
Fixes: d115b51e0e56 ("hwmon: add Corsair PSU HID controller driver")
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/YLjCJiVtu5zgTabI@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"The most notable fix is for the q54sj108a2 driver to let it actually
instantiate.
Also attribute fixes for pmbus/isl68137, pmbus/fsp-3y, and
dell-smm-hwmon drivers"
* tag 'hwmon-for-v5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon/pmbus: (q54sj108a2) The PMBUS_MFR_ID is actually 6 chars instead of 5
hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_3 for RAA228228
hwmon: (pmbus/fsp-3y) Fix FSP-3Y YH-5151E VOUT
hwmon: (dell-smm-hwmon) Fix index values
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here is a big set of char/misc/other driver fixes for 5.13-rc3.
The majority here is the fallout of the umn.edu re-review of all prior
submissions. That resulted in a bunch of reverts along with the
"correct" changes made, such that there is no regression of any of the
potential fixes that were made by those individuals. I would like to
thank the over 80 different developers who helped with the review and
fixes for this mess.
Other than that, there's a few habanna driver fixes for reported
issues, and some dyndbg fixes for reported problems.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (82 commits)
misc: eeprom: at24: check suspend status before disable regulator
uio_hv_generic: Fix another memory leak in error handling paths
uio_hv_generic: Fix a memory leak in error handling paths
uio/uio_pci_generic: fix return value changed in refactoring
Revert "Revert "ALSA: usx2y: Fix potential NULL pointer dereference""
dyndbg: drop uninformative vpr_info
dyndbg: avoid calling dyndbg_emit_prefix when it has no work
binder: Return EFAULT if we fail BINDER_ENABLE_ONEWAY_SPAM_DETECTION
cdrom: gdrom: initialize global variable at init time
brcmfmac: properly check for bus register errors
Revert "brcmfmac: add a check for the status of usb_register"
video: imsttfb: check for ioremap() failures
Revert "video: imsttfb: fix potential NULL pointer dereferences"
net: liquidio: Add missing null pointer checks
Revert "net: liquidio: fix a NULL pointer dereference"
media: gspca: properly check for errors in po1030_probe()
Revert "media: gspca: Check the return value of write_bridge for timeout"
media: gspca: mt9m111: Check write_bridge for timeout
Revert "media: gspca: mt9m111: Check write_bridge for timeout"
media: dvb: Add check on sp8870_readreg return
...
|
|
The PMBUS_MFR_ID block is actually 6 chars for q54sj108a2.
/sys/bus/i2c/drivers/q54sj108a2_test# iotools smbus_read8 $BUS $ADDR 0x99
0x06
Tested: Devices are able to bind to the q54sj108a2 driver successfully.
Signed-off-by: Chu Lin <linchuyuan@google.com>
Link: https://lore.kernel.org/r/20210517222606.3457594-1-linchuyuan@google.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The initial version of the RAA228228 datasheet claimed that the device
supported READ_TEMPERATURE_3 but not READ_TEMPERATURE_1. It has since been
discovered that the datasheet was incorrect. The RAA228228 does support
READ_TEMPERATURE_1 but does not support READ_TEMPERATURE_3.
Signed-off-by: Grant Peltier <grantpeltier93@gmail.com>
Fixes: 51fb91ed5a6f ("hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_1 telemetry for RAA228228")
Link: https://lore.kernel.org/r/20210514211954.GA24646@raspberrypi
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
After testing new YH-5151E devices, we found out that not all YH-5151E
work the same. The newly tested devices actually report vout correctly
in linear16 (even though they're still YH-5151E). We suspect that it is
because these new devices have a different firmware version, but that is
unconfirmed. The version cannot be queried through PMBus.
The compliant versions of YH-5151E report VOUT_MODE normally, so we turn
on the linear11 workaround only if VOUT_MODE doesn't report anything.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210513201110.313523-1-kubernat@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
When support for up to 10 temp sensors and for disabling automatic BIOS
fan control was added, noone updated the index values used for
disallowing fan support and fan type calls.
Fix those values.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210513154546.12430-1-W_Armin@gmx.de
Fixes: 1bb46a20e73b ("hwmon: (dell-smm) Support up to 10 temp sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This reverts commit 9aa3aa15f4c2f74f47afd6c5db4b420fadf3f315.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all so
just revert it. Also, the call to lm80_init_client() was not properly
handled, so if error handling is needed in the lm80_probe() function,
then it should be done properly, not half-baked like the commit being
reverted here did.
Cc: Kangjie Lu <kjlu@umn.edu>
Fixes: 9aa3aa15f4c2 ("hwmon: (lm80) fix a missing check of bus read in lm80 probe")
Cc: stable <stable@vger.kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210503115736.2104747-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When converting the driver to use the devm_hwmon_device_register_with_info
API, the wrong register was selected when writing into inX_max attributes.
Fix it.
Fixes: 124b7e34a5a6 ("hwmon: (adm9240) Convert to devm_hwmon_device_register_with_info API")
Reported-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
In each iteration fwnode_for_each_available_child_node() bumps a reference
counting of a loop variable followed by dropping in on a next iteration,
Since in error case the loop is broken, we have to drop a reference count
by ourselves. Do it for port_fwnode in error case during ->probe().
Fixes: b0bd407e94b0 ("hwmon: (ltc2992) Add support")
Cc: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210510100136.3303142-1-andy.shevchenko@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
I didn't properly test the driver for YH-5151E, so it was completely
broken. Firstly, the log/real mapping was incorrect in one case.
Secondly, PMBus specifies that output voltages should be in the linear16
encoding. However, the YH-5151E is non-compliant and uses linear11.
YM-2151E isn't affected by this. Fix this by converting the values
inside the read functions. linear16 gets the exponent from the VOUT_MODE
command. The device doesn't support it, so I have to manually supply the
value for it.
Both supported devices have now been tested to report correct vout
values.
Fixes: 1734b4135a62 ("hwmon: Add driver for fsp-3y PSUs and PDUs")
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210429075337.110502-1-kubernat@cesnet.cz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The poll rate limiter time was initialized at zero. This breaks the
comparison in time_after if jiffies is large. Switch to storing the
next update time rather than the previous time, and initialize the
time when the device is probed.
Fixes: c10e753d43eb ("hwmon (occ): Add sensor types and versions")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210429151336.18980-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix the following coccicheck warning:
./drivers/hwmon/corsair-psu.c:379:2-3: Unneeded semicolon
Remove unneeded semicolons.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20210427044219.7799-1-wanjiabing@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to the most recent upstream
revision including (but not limited to) new material introduced in the
6.4 version of the spec, update message printing in the ACPI-related
code, address a few issues and clean up code in a number of places.
Specifics:
- Update ACPICA code in the kernel to upstream revision 20210331
including the following changes:
* Add parsing for IVRS IVHD 40h and device entry F0h (Alexander
Monakov).
* Add new CEDT table for CXL 2.0 and iASL support for it (Ben
Widawsky, Bob Moore).
* NFIT: add Location Cookie field (Bob Moore).
* HMAT: add new fields/flags (Bob Moore).
* Add new flags in SRAT (Bob Moore).
* PMTT: add new fields/structures (Bob Moore).
* Add CSI2Bus resource template (Bob Moore).
* iASL: Decode subtable type field for VIOT (Bob Moore).
* Fix various typos and spelling mistakes (Colin Ian King).
* Add new predefined objects _BPC, _BPS, and _BPT (Erik Kaneda).
* Add USB4 capabilities UUID (Erik Kaneda).
* Add CXL ACPI device ID and _CBR object (Erik Kaneda).
* MADT: add Multiprocessor Wakeup Structure (Erik Kaneda).
* PCCT: add support for subtable type 5 (Erik Kaneda).
* PPTT: add new version of subtable type 1 (Erik Kaneda).
* Add SDEV secure access components (Erik Kaneda).
* Add support for PHAT table (Erik Kaneda).
* iASL: Add definitions for the VIOT table (Jean-Philippe
Brucker).
* acpisrc: Add missing conversion for VIOT support (Jean-Philippe
Brucker).
* IORT: Updates for revision E.b (Shameer Kolothum).
- Rearrange message printing in ACPI-related code to avoid using the
ACPICA's internal message printing macros outside ACPICA and do
some related code cleanups (Rafael Wysocki).
- Modify the device enumeration code to turn off all of the unused
ACPI power resources at the end (Rafael Wysocki).
- Change the ACPI power resources handling code to turn off unused
ACPI power resources without checking their status which should not
be necessary by the spec (Rafael Wysocki).
- Add empty stubs for CPPC-related functions to be used when
CONFIG_ACPI_CPPC_LIB is not set (Rafael Wysocki).
- Simplify device enumeration code (Rafael Wysocki).
- Change device enumeration code to use match_string() for string
matching (Andy Shevchenko).
- Modify irqresource_disabled() to retain the resouce flags that have
been set already (Angela Czubak).
- Add native backlight whitelist entry for GA401/GA502/GA503 (Luke
Jones).
- Modify the ACPI backlight driver to let the native backlight
handling take over on hardware-reduced systems (Hans de Goede).
- Introduce acpi_dev_get() and switch over the ACPI core code to
using it (Andy Shevchenko).
- Use kobj_attribute as callback argument instead of a local struct
type in the CPPC linrary code (Nathan Chancellor).
- Drop unneeded initializatio of a static variable from the ACPI
processor driver (Tian Tao).
- Drop unnecessary local variable assignment from the ACPI APEI code
(Colin Ian King).
- Document for_each_acpi_dev_match() macro (Andy Shevchenko).
- Address assorted coding style issues in multiple places (Xiaofei
Tan).
- Capitalize TLAs in a few comments (Andy Shevchenko).
- Correct assorted typos in comments (Tom Saeger)"
* tag 'acpi-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (68 commits)
ACPI: video: use native backlight for GA401/GA502/GA503
ACPI: APEI: remove redundant assignment to variable rc
ACPI: utils: Capitalize abbreviations in the comments
ACPI: utils: Document for_each_acpi_dev_match() macro
ACPI: bus: Introduce acpi_dev_get() and reuse it in ACPI code
ACPI: scan: Utilize match_string() API
resource: Prevent irqresource_disabled() from erasing flags
ACPI: CPPC: Replace cppc_attr with kobj_attribute
ACPI: scan: Call acpi_get_object_info() from acpi_set_pnp_ids()
ACPI: scan: Drop sta argument from acpi_init_device_object()
ACPI: scan: Drop sta argument from acpi_add_single_object()
ACPI: scan: Rearrange checks in acpi_bus_check_add()
ACPI: scan: Fold acpi_bus_type_and_status() into its caller
ACPI: video: Check LCD flag on ACPI-reduced-hardware devices
ACPI: utils: Add acpi_reduced_hardware() helper
ACPI: dock: fix some coding style issues
ACPI: sysfs: fix some coding style issues
ACPI: PM: add a missed blank line after declarations
ACPI: custom_method: fix a coding style issue
ACPI: CPPC: fix some coding style issues
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"The most notable change is the removal of the amd_energy driver. It
was rendered all but unusable by making its attributes privileged-only
to work around a security issue. A suggested remedy was rejected by
AMD, so the only real solution was to remove the driver. For the
future, we'll have to make sure that no privileged-access-only drivers
are accepted into the hwmon subsystem in the first place. The hwmon
ABI document was updated accordingly.
Other changes:
PMBus drivers:
- Added driver for MAX15301
- Added driver for BluTek BPA-RS600
- Added driver for fsp-3y PSUs and PDUs
- Added driver for Infineon IR36021
- Added driver for ST STPDDC60
- Added support for TI TPS53676 to tps53679 driver
- Introduced PMBUS symbol namespace. This was made necessary by a
suggestion to use its exported functions from outside the hwmon
subsystem.
- Minor improvements and bug fixes
New drivers:
- Driver for NZXT Kraken X42/X52/X62/X72
Driver enhancements:
- Added support for Intel D5005 to intel-m10-bmc-hwmon driver
- Added support for NCT6686D to nct6683 driver
Other:
- Converted sch5627 and amd9240 drivers to
hwmon_device_register_with_info()
- Added support for fan drawers capability and present registers to
mlxreg-fan driver
- Added Dell Latitude E7440 to fan control whitelist in dell-smm
driver
- Replaced snprintf in show functions with sysfs_emit. Done with
coccinelle script for all drivers to preempt endless per-driver
submissions of the same change.
- Use kobj_to_dev(). Another coccinelle based change to preempt
endless per-driver submissions of the same change.
- Various minor fixes and improvements"
* tag 'hwmon-for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (38 commits)
hwmon: Remove amd_energy driver
hwmon: Clarify scope of attribute access
hwmon: (pmbus) Introduce PMBUS symbol namespace
hwmon: (pmbus) Add pmbus driver for MAX15301
hwmon: (sch5627) Remove unnecessary error path
hwmon: (sch5627) Use devres function
hwmon: (pmbus/pxe1610) don't bail out when not all pages are active
hwmon: Add driver for fsp-3y PSUs and PDUs
hwmon: (intel-m10-bmc-hwmon) add sensor support of Intel D5005 card
hwmon: (sch5627) Split sch5627_update_device()
hwmon: (sch5627) Convert to hwmon_device_register_with_info()
hwmon: (nct6683) remove useless function
hwmon: (dell-smm) Add Dell Latitude E7440 to fan control whitelist
MAINTAINERS: Add keyword pattern for hwmon registration functions
hwmon: (mlxreg-fan) Add support for fan drawers capability and present registers
hwmon: (pmbus/tps53679) Add support for TI TPS53676
dt-bindings: Add trivial device entry for TPS53676
hwmon: (ftsteutates) Rudimentary typo fixes
hwmon: (pmbus) Add driver for BluTek BPA-RS600
dt-bindings: Add vendor prefix and trivial device for BluTek BPA-RS600
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big set of staging and IIO driver updates for 5.13-rc1.
Lots of little churn in here, and some larger churn as well. Major
things are:
- removal of wimax drivers, no one has this hardware anymore for this
failed "experiment".
- removal of the Google gasket driver, turns out no one wanted to
maintain it or cares about it anymore, so they asked for it to be
removed.
- comedi finally moves out of the staging directory into drivers/comedi
This is one of the oldest kernel subsystems around, being created
in the 2.0 kernel days, and was one of the first things added to
drivers/staging/ when that was created over 15 years ago.
It should have been moved out of staging a long time ago, it's well
maintained and used by loads of different devices in the real world
every day. Nice to see this finally happen.
- so many tiny coding style cleanups it's not funny.
Perfect storm of at least 2 different intern project application
deadlines combined to provide a huge number of new contributions in
this area from people learning how to do kernel development. Great
job to everyone involved here.
There's also the normal updates for IIO drivers with new IIO drivers
and updates all over that subsystem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (907 commits)
staging: octeon: Use 'for_each_child_of_node'
Staging: rtl8723bs: rtw_xmit: fixed tabbing issue
staging: rtl8188eu: remove unused function parameters
staging: rtl8188eu: cmdThread is a task_struct
staging: rtl8188eu: remove constant variable and dead code
staging: rtl8188eu: change bLeisurePs' type to bool
staging: rtl8723bs: remove empty #ifdef block
staging: rtl8723bs: remove unused DBG_871X_LEVEL macro declarations
staging: rtl8723bs: split too long line
staging: rtl8723bs: fix indentation in if block
staging: rtl8723bs: fix code indent issue
staging: rtl8723bs: replace DBG_871X_LEVEL logs with netdev_*()
staging: rtl8192e: indent statement properly
staging: rtl8723bs: Remove led_blink_hdl() and everything related
staging: comedi: move out of staging directory
staging: rtl8723bs: remove sdio_drv_priv structure
staging: rtl8723bs: remove unused argument in function
staging: rtl8723bs: remove DBG_871X_SEL_NL macro declaration
staging: rtl8723bs: replace DBG_871X_SEL_NL with netdev_dbg()
staging: rtl8723bs: fix indentation issue introduced by long line split
...
|
|
Commit 60268b0e8258 ("hwmon: (amd_energy) modify the visibility of
the counters") restricted visibility of AMD energy counters to work
around a side-channel attack using energy data to determine which
instructions are executed. The attack is described in 'PLATYPUS:
Software-based Power Side-Channel Attacks on x86'. It relies on quick
and accurate energy readings.
This change made the counters provided by the amd_energy driver
effectively unusable for non-provileged users. However, unprivileged
read access is the whole point of hardware monitoring attributes.
An attempt to remedy the situation by limiting and randomizing access
to chip registers was rejected by AMD. Since the driver is for all
practical purposes unusable, remove it.
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Exported pmbus symbols are only supposed to be used from PMBus code.
Introduce PMBUS symbol namespace to prevent misuse from other code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add pmbus driver support for Maxim MAX15301 InTune Automatically
Compensated Digital PoL Controller with Driver and PMBus Telemetry
Even though the specification does not specifically mention it,
extensive empirical testing has revealed that auto-detection of
limit-registers will fail in a random fashion unless the delay
parameter is set to above about 80us. The default delay is set
to 100us to include some safety margin.
This patch is tested on a Flex BMR461 converter module.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210419101251.24840-1-erik.rosen@metormote.com
[groeck: Added rationale for delay to driver header]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Calling remove() on error whould have only unregistered
the watchdog, and since a failure in registering him
is considered non-fatal and happens last, remove the
error path and return the error codes directly.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20210417210920.15496-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use devm_hwmon_device_register_with_info() and remove hwmon_dev
from sch5627_data struct as it is not needed anymore.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20210417210920.15496-2-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Certain VRs might be configured to use only the first output channel and
so the mode for the second will be 0. Handle this gracefully.
Fixes: b9fa0a3acfd8 ("hwmon: (pmbus/core) Add support for vid mode detection per page bases")
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210416102926.13614-1-fercerpav@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds support for these devices:
- YH-5151E - the PDU
- YM-2151E - the PSU
The device datasheet says that the devices support PMBus 1.2, but in my
testing, a lot of the commands aren't supported and if they are, they
sometimes behave strangely or inconsistently. For example, writes to the
PAGE command requires using PEC, otherwise the write won't work and the
page won't switch, even though, the standard says that PEC is optional.
On the other hand, writes to SMBALERT don't require PEC. Because of
this, the driver is mostly reverse engineered with the help of a tool
called pmbus_peek written by David Brownell (and later adopted by my
colleague Jan Kundrát).
The device also has some sort of a timing issue when switching pages,
which is explained further in the code.
Because of this, the driver support is limited. It exposes only the
values that have been tested to work correctly.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210414080019.3530794-1-kubernat@cesnet.cz
[groeck: Fixed up "missing braces around initializer" from 0-day]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Like the Intel N3000 card, the Intel D5005 has a MAX10 based
BMC. This commit adds support for the D5005 sensors that are
monitored by the MAX10 BMC.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210413225835.459662-3-matthew.gerlach@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
An error in sch5627_update_device() could cause sch5627_read()
to fail even if the error did not affect the target sensor type.
Split sch5627_update_device() to prevent that.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210411164225.11967-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
hwmon_device_register() is deprecated.
Convert driver to use hwmon_device_register_with_info() and
remove sysfs attributes which are now being handled by the
hwmon subsystem.
Channel handling was inspired by corsair-cpro.
Tested on a Fujitsu Esprimo P720.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210411164225.11967-2-W_Armin@gmx.de
[groeck: Replaced 0 with NULL]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix the following clang warning:
drivers/hwmon/nct6683.c:491:19: warning: unused function 'in_to_reg'
[-Wunused-function].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/1618293770-55307-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Allow manual PWM control on Dell Latitude E7440.
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210411095741.zmllsuc7pevdipvy@icloud.com
Signed-off-by: Sebastian Oechsle <setboolean@icloud.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for fan drawer's capability and present registers in order
to set mapping between the fan drawers and tachometers. Some systems
are equipped with fan drawers with one tachometer inside. Others with
fan drawers with several tachometers inside. Using present register
along with tachometer-to-drawer mapping allows to skip reading missed
tachometers and expose input for them as zero, instead of exposing
fault code returned by hardware.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210322172237.2213584-1-vadimp@nvidia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for TI TPS53676 controller to the tps53679 pmbus driver
The driver uses the USER_DATA_03 register to figure out how many phases
are enabled and to which channel they are assigned, and sets the number
of pages and phases accordingly.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210322193734.75127-3-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
s/Temprature/Temperature/
s/revsion/revision/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210323043438.1321903-1-unixbhaskar@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The BPA-RS600 is a compact 600W AC to DC removable power supply module.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210317040231.21490-3-chris.packham@alliedtelesis.co.nz
[groeck: Added bpa-rs600 to index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
coccicheck complains about the use of snprintf() in sysfs
show functions.
drivers/hwmon/ina3221.c:701:8-16: WARNING: use scnprintf or sprintf
This results in a large number of patch submissions. Fix it all in
one go using the following coccinelle rules. Use sysfs_emit instead
of scnprintf or sprintf since that makes more sense.
@depends on patch@
identifier show, dev, attr, buf;
@@
ssize_t show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
return
- snprintf(buf, \( PAGE_SIZE \| PAGE_SIZE - 1 \),
+ sysfs_emit(buf,
...);
...>
}
@depends on patch@
identifier show, dev, attr, buf, rc;
@@
ssize_t show(struct device *dev, struct device_attribute *attr, char *buf)
{
<...
rc =
- snprintf(buf, \( PAGE_SIZE \| PAGE_SIZE - 1 \),
+ sysfs_emit(buf,
...);
...>
}
While at it, remove unnecessary braces and as well as unnecessary
else after return statements to address checkpatch warnings in the
resulting patch.
Cc: Zihao Tang <tangzihao1@hisilicon.com>
Cc: Jay Fang <f.fangjian@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The hwmon sysfs ABI requires that the `name` property doesn't include
any dashes. But when the pmbus code picks the name up from the device
tree it quite often does. Replace '-' with '_' before registering the
device.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210317040231.21490-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
These are "all-in-one" CPU liquid coolers that can be monitored and
controlled through a proprietary USB HID protocol.
While the models have differently sized radiators and come with varying
numbers of fans, they are all indistinguishable at the software level.
The driver exposes fan/pump speeds and coolant temperature through the
standard hwmon sysfs interface.
Fan and pump control, while supported by the devices, are not currently
exposed. The firmware accepts up to 61 trip points per channel
(fan/pump), but the same set of trip temperatures has to be maintained
for both; with pwmX_auto_point_Y_temp attributes, users would need to
maintain this invariant themselves.
Instead, fan and pump control, as well as LED control (which the device
also supports for 9 addressable RGB LEDs on the CPU water block) are
left for existing and already mature user-space tools, which can still
be used alongside the driver, thanks to hidraw. A link to one, which I
also maintain, is provided in the documentation.
The implementation is based on USB traffic analysis. It has been
runtime tested on x86_64, both as a built-in driver and as a module.
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20210319045544.416138-1-jonas@protocubo.io
[groeck: Removed unnecessary spinlock.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix the following coccicheck warning:
drivers/hwmon/ina2xx.c:313:8-16: WARNING: use scnprintf or sprintf
drivers/hwmon/ina2xx.c:453:8-16: WARNING: use scnprintf or sprintf
drivers/hwmon/ina2xx.c:484:8-16: WARNING: use scnprintf or sprintf
drivers/hwmon/ina2xx.c:540:8-16: WARNING: use scnprintf or sprintf
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1615892457-35501-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
coccinelle complains about
WARNING opportunity for kobj_to_dev()
in several files, resulting in one-by-one patch submissions.
Handle all remaining instances in one go.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
fixed the following coccicheck:
./drivers/hwmon/ds1621.c:329:60-61: WARNING opportunity
for kobj_to_dev().
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1616032504-59817-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Change 'revsion' to 'revision'.
Signed-off-by: zuoqilin <zuoqilin@yulong.com>
Link: https://lore.kernel.org/r/20210318124637.1331-1-zuoqilin1@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Adds support for reading the critical values of the temperature sensors
and the rail sensors (voltage and current) once and caches them. Updates
the naming of the constants following a more clear scheme. Also updates
the documentation and fixes some typos. Updates is_visible and ops_read
functions to be more readable.
The new sensors output of a Corsair HX850i will look like this:
corsairpsu-hid-3-1
Adapter: HID adapter
v_in: 230.00 V
v_out +12v: 12.14 V (crit min = +8.41 V, crit max = +15.59 V)
v_out +5v: 5.03 V (crit min = +3.50 V, crit max = +6.50 V)
v_out +3.3v: 3.30 V (crit min = +2.31 V, crit max = +4.30 V)
psu fan: 0 RPM
vrm temp: +46.2°C (crit = +70.0°C)
case temp: +39.8°C (crit = +70.0°C)
power total: 152.00 W
power +12v: 108.00 W
power +5v: 41.00 W
power +3.3v: 5.00 W
curr +12v: 9.00 A (crit max = +85.00 A)
curr +5v: 8.31 A (crit max = +40.00 A)
curr +3.3v: 1.62 A (crit max = +40.00 A)
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/YFNg6vGk3sQmyqgB@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add hardware monitoring support for ST STPDDC60 Unversal Digital
Multicell Controller.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-3-erik.rosen@metormote.com
[groeck: Fixed whitespace error in Makefile]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
For the STPDDC60 chip, the vout alarm-limits are represented as an offset
relative to the commanded output voltage. This means that the limits are
dynamic and must not be cached by the pmbus driver. This patch adds a
pmbus_set_sensor() function to pmbus_core to be able to set the update flag
on selected sensors after auto-detection of limit attributes.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-2-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for NCT6686D chip used in the Lenovo P620.
Signed-off-by: Jiqi Li <lijq9@lenovo.com>
Reviewed-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20210304104421.1912934-1-lijq9@lenovo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The IR36021 is a dual‐loop digital multi‐phase buck controller.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210301035954.16713-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Changes the way how LINEAR11 values are calculated. The new method
increases the precision of 2-3 digits.
old method:
corsairpsu-hid-3-1
Adapter: HID adapter
v_in: 230.00 V
v_out +12v: 12.00 V
v_out +5v: 5.00 V
v_out +3.3v: 3.00 V
psu fan: 0 RPM
vrm temp: +44.0°C
case temp: +37.0°C
power total: 152.00 W
power +12v: 112.00 W
power +5v: 38.00 W
power +3.3v: 5.00 W
curr in: N/A
curr +12v: 9.00 A
curr +5v: 7.00 A
curr +3.3v: 1000.00 mA
new method:
corsairpsu-hid-3-1
Adapter: HID adapter
v_in: 230.00 V
v_out +12v: 12.16 V
v_out +5v: 5.01 V
v_out +3.3v: 3.30 V
psu fan: 0 RPM
vrm temp: +44.5°C
case temp: +37.8°C
power total: 148.00 W
power +12v: 108.00 W
power +5v: 37.00 W
power +3.3v: 4.50 W
curr in: N/A
curr +12v: 9.25 A
curr +5v: 7.50 A
curr +3.3v: 1.50 A
Co-developed-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Jack Doan <me@jackdoan.com>
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/YDoSMqFbgoTXyoru@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
