summaryrefslogtreecommitdiff
path: root/drivers/i2c/busses/i2c-sh_mobile.c
AgeCommit message (Collapse)AuthorFilesLines
2019-11-14i2c: sh_mobile: Use dma_request_chan() directly for channel requestPeter Ujfalusi1-1/+1
dma_request_slave_channel_reason() is: dma_request_chan(dev, name) Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-02-09i2c: sh_mobile: use new clock calculation formulas for Gen2Wolfram Sang1-5/+5
We measured the clock on a Lager and an Ebisu board. The new formula gives better results for both. So after Gen3, switch to this formula for all Gen2 SoCs. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-02-09i2c: sh_mobile: use new clock calculation formulas for Gen3Wolfram Sang1-3/+3
We could finally measure the clock on an Ebisu board. The new formula gives way better results, i.e. 100kHz instead of 106kHz and 400kHz instead of 387kHz. Switch to these formulas for all Gen3 SoCs. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-02-09i2c: sh_mobile: sort compatible entriesWolfram Sang1-2/+2
Makes it easier to add new ones. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-01-23i2c: sh_mobile: update copyright and commentsWolfram Sang1-4/+3
Update copyright years and add Renesas to it. Add/update comments to make driver easier to understand. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-01-23i2c: sh_mobile: refactor rx isrWolfram Sang1-29/+21
Remove the do_while loop which was just there to have an easy exit with "break;" and replace it with if-else-blocks which should make the state machine clearer. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-01-23i2c: sh_mobile: replace break; with if-blockWolfram Sang1-4/+3
In preparation to remove the do-while-loop. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-01-23i2c: sh_mobile: remove is_first_byte functionWolfram Sang1-7/+2
All state machines deal with pd->pos values. This helper function is an exception and makes it only more confusing. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-01-23i2c: sh_mobile: drop 'data' argument from i2c_op functionWolfram Sang1-24/+17
It is clear that we always send the address in TX_FIRST and data in TX. No need to pass it from the caller. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-01-23i2c: sh_mobile: remove get_data functionWolfram Sang1-15/+8
It makes the code much easier comprehensible to explicitly code that the first byte will be client address and all the following bytes are the actual data. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-01-23i2c: sh_mobile: simplify sending address for RXWolfram Sang1-6/+2
pd->pos won't be smaller than -1, so we can simplify the logic. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-12-18i2c: sh_mobile: Add support for r8a774c0 (RZ/G2E)Fabrizio Castro1-0/+1
Similarly to R-Car E3, RZ/G2E doesn't come with automatic transmission registers, as such it is not considered compatible with the existing fallback bindings. Add SoC specific binding compatibility to allow for later support for automatic transmission. Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-11-27i2c: sh_mobile: add support for r8a77990 (R-Car E3)Simon Horman1-0/+1
Add support for the IIC code for the r8a77990 (R-Car E3). It is not considered compatible with existing fallback bindings due to the documented absence of automatic transmission registers. These registers are currently not used by the driver and thus the provides the same behaviour for "renesas,iic-r8a77990" and "renesas,rcar-gen3-iic". The point of declaring incompatibility is to allow for automatic transmission register support to be added to "renesas,iic-r8a77990" and "renesas,rcar-gen3-iic" in future. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-10-29i2c: sh_mobile: Remove dummy runtime PM callbacksJarkko Nikula1-18/+0
Platform drivers don't need dummy runtime PM callbacks that just return success and non-NULL pm pointer in their struct device_driver in order to have runtime PM happening. This has changed since following commits: 05aa55dddb9e ("PM / Runtime: Lenient generic runtime pm callbacks") 543f2503a956 ("PM / platform_bus: Allow runtime PM by default") 8b313a38ecff ("PM / Platform: Use generic runtime PM callbacks directly") Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-08-31i2c: sh_mobile: fix leak when using DMA bounce bufferWolfram Sang1-2/+4
We only freed the bounce buffer after successful DMA, missing the cases where DMA setup may have gone wrong. Use a better location which always gets called after each message and use 'stop_after_dma' as a flag for a successful transfer. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-08-31i2c: sh_mobile: define start_ch() void as it only returns 0 anyhowWolfram Sang1-6/+3
After various refactoring over the years, start_ch() doesn't return errno anymore, so make the function return void. This saves the error handling when calling it which in turn eases cleanup of resources of a future patch. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-08-31i2c: refactor function to release a DMA safe bufferWolfram Sang1-1/+1
a) rename to 'put' instead of 'release' to match 'get' when obtaining the buffer b) change the argument order to have the buffer as first argument c) add a new argument telling the function if the message was transferred. This allows the function to be used also in cases where setting up DMA failed, so the buffer needs to be freed without syncing to the message buffer. Also convert the only user. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-08-24i2c: use SPDX identifier for Renesas driversWolfram Sang1-9/+1
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-08-05i2c: sh_mobile: use core to detect 'no zero length read' quirkWolfram Sang1-5/+5
And don't reimplement in the driver. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-05-09i2c: busses: remove superfluous ignoring of children for RPMWolfram Sang1-11/+0
These days, the I2C core ensures that the embedded adapter device ignores the PM states of its children already. Because the adapter device is an opaque logical device, there is no need for drivers to repeat that again. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15i2c: sh_mobile: let r8a7790 (R-Car H2) use the new formulaWolfram Sang1-1/+1
Make use of the new formula for more precise bus frequencies. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15i2c: sh_mobile: add new frequency calculation for later SoCWolfram Sang1-1/+18
The formula to generate the desired bus speeds has changed a little over time. Implement the new formula and allow drivers to opt-in by changing to this new config set. Ensure in probe that we don't divide by zero. The returned values on a R-Car H2 (r8a7790/Lager board) match the suggested values in the datasheet. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15i2c: sh_mobile: add helper to check frequency calculationsWolfram Sang1-22/+27
Because we will add a second formula soon, put the sanity checks for the computed results into a separate function. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15i2c: sh_mobile: let RuntimePM do the clock handlingWolfram Sang1-18/+17
Start RuntimePM a bit earlier, so we can use it to enable the clock during probe for frequency calculations. Make sure it is enabled before calling setup(). Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15i2c: sh_mobile: require setup callbackWolfram Sang1-9/+6
Require the setup callback and move the frequency calculation into it. This is in preparation for supporting multiple formulas. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15i2c: sh_mobile: allow setup callback to return errnoWolfram Sang1-4/+9
The setup callback will be more generic and, thus, need to be able to return error codes. Change the return type to 'int' for that. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2018-01-15i2c: sh_mobile: move type detection upwardsWolfram Sang1-6/+4
For refactoring reasons, we will need this information before the setup callback. Also, simplify the comment to a oneliner. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-12-03i2c: sh_mobile: use core helper to decide when to use DMAWolfram Sang1-2/+6
This ensures that we fall back to PIO if the message length is too small for DMA being useful. Otherwise, we use DMA. A bounce buffer might be applied by the helper if the original message buffer is not DMA safe. Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: make sure to not accidently trigger STOPWolfram Sang1-3/+3
The datasheet was a bit vague, but after consultation with HW designers, we came to the conclusion that we should set the SCP bit always when dealing only with the ICE bit. A set SCP bit is ignored, and thus fine, a cleared one may trigger STOP on the bus. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: send STOP according to datasheetWolfram Sang1-23/+6
We initiate STOP (or REP_START) on the second last WAIT interrupt currently. This works fine but is not according to the datasheet which says to do it on the last WAIT interrupt. This also simplifies the code quite a lot, so let's do it. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: avoid unnecessary register readWolfram Sang1-1/+2
There is no data when the first WAIT interrupt arrives. No need to read something then. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: let RuntimePM do the clock handlingWolfram Sang1-2/+0
No need to do it manually. Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: shorten exit of xfer routineWolfram Sang1-3/+1
We can use the ternary operator for easier reading. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: use direct writes when accessing ICE bitWolfram Sang1-3/+3
ICE bit is for resetting the module. Other bits don't matter then, so we don't need to use the iic_set_clr() function but can use iic_wr(). Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: manually "inline" two short functionsWolfram Sang1-19/+9
Those two functions are very short and only called once. The code becomes easier to understand if the code is directly put into the main xfer function. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: remove redundant deinitializationWolfram Sang1-4/+0
No need to clear the interrupt registers because right after that we disable the IP core which will reload registers with their initial values anyhow. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-11-27i2c: sh_mobile: remove redundant initializationWolfram Sang1-10/+0
Following the documentation, we initialize the HW before each START in start_ch(). No need to do the same in activate_ch(). Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-10-18i2c: sh_mobile: Use of_device_get_match_data() helperGeert Uytterhoeven1-5/+3
Use the of_device_get_match_data() helper instead of open coding. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-08-17i2c: sh_mobile: avoid unused ret variableEugeniu Rosca1-2/+2
Fix smatch warning: drivers/i2c/busses/i2c-sh_mobile.c:564 \ sh_mobile_i2c_request_dma_chan() warn: unused return: ret = PTR_ERR() Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-06-02i2c: sh_mobile: drop needless check for of_nodeWolfram Sang1-12/+7
After removal of platform_data support, we can simplify OF handling. of_match_device() evaluates to NULL if !CONFIG_OF or if there is no node pointer for that device, so we can remove the check for the node ptr. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-06-02i2c: sh_mobile: remove platform_dataWolfram Sang1-8/+0
No platform currently upstream makes use of this platform_data anymore. The ones that did are converted to DT meanwhile. So, remove it. The old platforms likely don't have the 'clks_per_cnt' feature, otherwise it would have been implemented by now. And in the unlikely case they need to setup a different bus speed, we should rather go for a generic i2c platform data just for that. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2017-02-09i2c: busses: constify i2c_algorithm structuresBhumika Goyal1-1/+1
Declare i2c_algorithm structures as const as they are only stored in the algo field of an i2c_adapter structure. This field is of type const, so i2c_algorithm structures having this property can be made const too. Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> for Acked-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-12i2c: sh_mobile: Add per-Generation fallback bindingsSimon Horman1-1/+3
Add per-Generation fallback bindings for R-Car SoCs. This is in keeping with the compatibility string scheme is being adopted for drivers for Renesas SoCs. Also, improve readability by listing the rmobile fallback compatibility string after the more-specific compatibility strings they provide a fallback for. Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-08Merge branch 'i2c/for-4.9' of ↵Linus Torvalds1-1/+0
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c updates from Wolfram Sang: "Here is the 4.9 pull request from I2C including: - centralized error messages when registering to the core - improved lockdep annotations to prevent false positives - DT support for muxes, gates, and arbitrators - bus speeds can now be obtained from ACPI - i2c-octeon got refactored and now supports ThunderX SoCs, too - i2c-tegra and i2c-designware got a bigger bunch of updates - a couple of standard driver fixes and improvements" * 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits) i2c: axxia: disable clks in case of failure in probe i2c: octeon: thunderx: Limit register access retries i2c: uniphier-f: fix misdetection of incomplete STOP condition gpio: pca953x: variable 'id' was used twice i2c: i801: Add support for Kaby Lake PCH-H gpio: pca953x: fix an incorrect lockdep warning i2c: add a warning to i2c_adapter_depth() lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible i2c: export i2c_adapter_depth() i2c: rk3x: Fix variable 'min_total_ns' unused warning i2c: rk3x: Fix sparse warning i2c / ACPI: Do not touch an I2C device if it belongs to another adapter i2c: octeon: Fix high-level controller status check i2c: octeon: Avoid sending STOP during recovery i2c: octeon: Fix set SCL recovery function i2c: rcar: add support for r8a7796 (R-Car M3-W) i2c: imx: make bus recovery through pinctrl optional i2c: meson: add gxbb compatible string i2c: uniphier-f: set the adapter to master mode when probing i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path ...
2016-08-25i2c: sh_mobile: use proper device with dma_mapping_errorWolfram Sang1-1/+1
We must use the same device we used for mapping. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-08-22i2c: don't print error when adding adapter failsWolfram Sang1-1/+0
The core will do this for us now. Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Peter Korsgaard <peter@korsgaard.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Ray Jui <ray.jui@broadcom.com> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-04-11i2c: sh_mobile: use new 8 bit address helper functionWolfram Sang1-2/+1
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20i2c: sh_mobile: add support for r8a7795 (R-Car H3)Wolfram Sang1-0/+1
Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so reuse the settings. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23i2c: sh_mobile: use proper type for timeoutWolfram Sang1-3/+4
wait_event_timeout returns long, not int. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23i2c: sh_mobile: use adapter default for timeoutWolfram Sang1-1/+1
5 seconds is a very large timeout, and it is hardcoded. Use the default timeout from 'struct adapter' which is 1 second. It can also be modified from userspace for specific workloads via i2c-dev. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-19 16:39:09 +0300