| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The RGB + IR data can be used to calculate the illuminance value (luxes).
Implement the equation obtained from the ROHM HW colleagues and add a
raw light data channel outputting illuminance values in (nano) Luxes.
Both the read_raw and buffering values are supported, with the limitation
that buffering is only allowed when a suitable scan-mask is used. (RGB+IR,
no clear).
The equation has been developed by ROHM HW colleagues for open air sensor.
Adding any lens to the sensor is likely to impact to used c1, c2, c3
coefficients. Also, the output values have only been tested on BU27008.
According to the HW colleagues, the very same equation should work on
BU27010 as well.
Calculate and output illuminance values from BU27008 and BU27010.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/ZTJcOxSb/WHzdN8h@dc78bmyyyyyyyyyyyyydt-3.rev.dnainternet.fi
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We need the char/misc fixes in here as well to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ROHM BU27010 is an RGBC sensor with a flickering detection FIFO. The
RGBC+IR sensor functionality is largely similar to what the BU27008 has.
There are some notable things though:
- gain setting is once again new and exotic. Now, there is 6bit gain
setting where 4 of the bits are common to all channels and 2 bits
can be configured separately for each channel. The BU27010 has
similar "1X on other channels vs 2X on IR when selector is 0x0"
gain design as BU27008 had. So, we use same gain setting policy for
BU27010 as we did for BU27008 - driver sets same gain selector for all
channels but shows the gains separately for all channels so users
can (at least in theory) detect this 1X vs 2X madness...
- BU27010 has suffled all the control register bitfields to new
addresses and bit positions while still keeping the register naming
same.
- Some more power/reset control is added.
- FIFO for "flickering detection" is added.
The control register suffling made this slightly nasty. Still, it is
easier for maintenance perspective to add the BU27010 support in BU27008
driver because - even though the bit positions/addresses were changed -
most of the driver structure can be re-used. Writing own driver for
BU27010 would mean plenty of duplicate code albeit a tad more clarity.
The flickering FIFO is not supported by the driver.
Add BU27010 RGBC+IR support to rohm-bu27008 driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/111cd217ccece1c1f16ab4287532dc4e1ddb8a3f.1690958450.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ROHM BU27010 RGB + flickering sensor is in many regards similar to
the BU27008. Prepare for adding support for BU27010 by allowing
chip-specific properties to be brought from the of_device_id data.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/d5994648033d5513993b8d72eb186ddda211b5ac.1690958450.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The intensity data from bu27008 is unsigned. The type of the scan data
was incorrectly marked as signed resulting large intensity values to be
interpreted as negative ones.
Fix the scan data type.
Fixes: 41ff93d14f78 ("iio: light: ROHM BU27008 color sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/240a7ca5fc1b76da20d81f930d00f31a54b1fdf8.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The driver is expecting accuracy of NANOs for intensity scale in
raw_write. The IIO core is however defaulting to MICROs. This leads the
raw-write of smallest scales to never succeed as correct selector(s) are
not found.
Fix this by implementing the .write_raw_get_fmt callback to use NANO
accuracy for writes of IIO_CHAN_INFO_SCALE.
Fixes: 41ff93d14f78 ("iio: light: ROHM BU27008 color sensor")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/e4778b74cde41431f77bc8dd88ec18605da0b400.1686648422.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ROHM BU27008 is a sensor with 5 photodiodes (red, green, blue, clear
and IR) with four configurable channels. Red and green being always
available and two out of the rest three (blue, clear, IR) can be
selected to be simultaneously measured. Typical application is adjusting
LCD backlight of TVs, mobile phones and tablet PCs.
Add initial support for the ROHM BU27008 color sensor.
- raw_read() of RGB and clear channels
- triggered buffer w/ DRDY interrtupt
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/2594162f0e44148cffb1fb05f1d6edfde6bd11bc.1683541225.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
