| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"In the raw NAND subsystem, the major fix prevents using cached reads
with devices not supporting it. There was two bug reports about this.
Apart from that, three drivers (pl353, arasan and marvell) could
sometimes hide page program failures due to their their own program
page helper not being fully compliant with the specification (many
drivers use the default helpers shared by the core). Adding a missing
check prevents these situation.
Finally, the Qualcomm driver had a broken error path.
In the SPI-NAND subsystem one Micron device used a wrong bitmak
reporting possibly corrupted ECC status.
Finally, the physmap-core got stripped from its map_rom fallback by
mistake, this feature is added back"
* tag 'mtd/fixes-for-6.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: Ensure the nand chip supports cached reads
mtd: rawnand: qcom: Unmap the right resource upon probe failure
mtd: rawnand: pl353: Ensure program page operations are successful
mtd: rawnand: arasan: Ensure program page operations are successful
mtd: spinand: micron: correct bitmask for ecc status
mtd: physmap-core: Restore map_rom fallback
mtd: rawnand: marvell: Ensure program page operations are successful
|
|
Both the JEDEC and ONFI specification say that read cache sequential
support is an optional command. This means that we not only need to
check whether the individual controller supports the command, we also
need to check the parameter pages for both ONFI and JEDEC NAND flashes
before enabling sequential cache reads.
This fixes support for NAND flashes which don't support enabling cache
reads, i.e. Samsung K9F4G08U0F or Toshiba TC58NVG0S3HTA00.
Sequential cache reads are now only available for ONFI and JEDEC
devices, if individual vendors implement this, it needs to be enabled
per vendor.
Tested on i.MX6Q with a Samsung NAND flash chip that doesn't support
sequential reads.
Fixes: 003fe4b9545b ("mtd: rawnand: Support for sequential cache reads")
Cc: stable@vger.kernel.org
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230922141717.35977-1-r.czerwinski@pengutronix.de
|
|
We currently provide the physical address of the DMA region
rather than the output of dma_map_resource() which is obviously wrong.
Fixes: 7330fc505af4 ("mtd: rawnand: qcom: stop using phys_to_dma()")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bibek Kumar Patro <quic_bibekkum@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230913070702.12707-1-quic_bibekkum@quicinc.com
|
|
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: Michal Simek <michal.simek@amd.com>
Cc: stable@vger.kernel.org
Fixes: 08d8c62164a3 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-3-miquel.raynal@bootlin.com
|
|
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: Michal Simek <michal.simek@amd.com>
Cc: stable@vger.kernel.org
Fixes: 88ffef1b65cf ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-2-miquel.raynal@bootlin.com
|
|
Valid bitmask is 0x70 in the status register.
Fixes: a508e8875e13 ("mtd: spinand: Add initial support for Micron MT29F2G01ABAGD")
Signed-off-by: Martin Kurbanov <mmkurbanov@sberdevices.ru>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230905145637.139068-1-mmkurbanov@sberdevices.ru
|
|
When the exact mapping type driver was not available, the old
physmap_of_core driver fell back to mapping the region as ROM.
Unfortunately this feature was lost when the DT and pdata cases were
merged. Revive this useful feature.
Fixes: 642b1e8dbed7bbbf ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/550e8c8c1da4c4baeb3d71ff79b14a18d4194f9e.1693407371.git.geert+renesas@glider.be
|
|
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: stable@vger.kernel.org
Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ravi Chandra Minnikanti <rminnikanti@marvell.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-1-miquel.raynal@bootlin.com
|
|
There exists mtd devices with zero erasesize, which will trigger a
divide-by-zero exception while attaching ubi device.
Fix it by refusing attaching if mtd's erasesize is 0.
Fixes: 801c135ce73d ("UBI: Unsorted Block Images")
Reported-by: Yu Hao <yhao016@ucr.edu>
Link: https://lore.kernel.org/lkml/977347543.226888.1682011999468.JavaMail.zimbra@nod.at/T/
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull NFD updates from Lee Jones:
"New Drivers:
- Add support for the Cirrus Logic CS42L43 Audio CODEC
Fix-ups:
- Make use of specific printk() format tags for various optimisations
- Kconfig / module modifications / tweaking
- Simplify obtaining resources (memory, device data) using unified
API helpers
- Bunch of Device Tree additions, conversions and adaptions
- Convert a bunch of Regmap configurations to use the Maple Tree
cache
- Ensure correct includes are present and remove some that are not
required
- Remove superfluous code
- Reduce amount of cycles spent in critical sections
- Omit the use of redundant casts and if relevant replace with better
ones
- Swap out raw_spin_{un}lock_irq{save,restore}() for
spin_{un}lock_irq{save,restore}()
Bug Fixes:
- Repair theoretical deadlock situation
- Fix some link-time dependencies
- Use more appropriate datatype when casting"
* tag 'mfd-next-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (70 commits)
mfd: mc13xxx: Simplify device data fetching in probe()
mfd: rz-mtu3: Replace raw_spin_lock->spin_lock()
mfd: rz-mtu3: Reduce critical sections
mfd: mxs-lradc: Fix Wvoid-pointer-to-enum-cast warning
mfd: wm31x: Fix Wvoid-pointer-to-enum-cast warning
mfd: wm8994: Fix Wvoid-pointer-to-enum-cast warning
mfd: tc3589: Fix Wvoid-pointer-to-enum-cast warning
mfd: lp87565: Fix Wvoid-pointer-to-enum-cast warning
mfd: hi6421-pmic: Fix Wvoid-pointer-to-enum-cast warning
mfd: max77541: Fix Wvoid-pointer-to-enum-cast warning
mfd: max14577: Fix Wvoid-pointer-to-enum-cast warning
mfd: stmpe: Fix Wvoid-pointer-to-enum-cast warning
mfd: rn5t618: Remove redundant of_match_ptr()
mfd: lochnagar-i2c: Remove redundant of_match_ptr()
mfd: stpmic1: Remove redundant of_match_ptr()
mfd: act8945a: Remove redundant of_match_ptr()
mfd: rsmu_spi: Remove redundant of_match_ptr()
mfd: altera-a10sr: Remove redundant of_match_ptr()
mfd: rsmu_i2c: Remove redundant of_match_ptr()
mfd: tc3589x: Remove redundant of_match_ptr()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"Core MTD changes:
- Use refcount to prevent corruption
- Call external _get and _put in right order
- Fix use-after-free in mtd release
- Explicitly include correct DT includes
- Clean refcounting with MTD_PARTITIONED_MASTER
- mtdblock: make warning messages ratelimited
- dt-bindings: Add SEAMA partition bindings
Device driver changes:
- Use devm helper functions
- Fix questionable cast, remove pointless ones.
- error handling fixes
- add support for new chip versions
- update DT bindings
- misc cleanups - fix typos, whitespace, indentation"
* tag 'mtd/for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (105 commits)
dt-bindings: mtd: amlogic,meson-nand: drop unneeded quotes
mtd: spear_smi: Use helper function devm_clk_get_enabled()
mtd: rawnand: orion: Use helper function devm_clk_get_optional_enabled()
mtd: rawnand: vf610_nfc: Use helper function devm_clk_get_enabled()
mtd: rawnand: sunxi: Use helper function devm_clk_get_enabled()
mtd: rawnand: stm32_fmc2: Use helper function devm_clk_get_enabled()
mtd: rawnand: mtk: Use helper function devm_clk_get_enabled()
mtd: rawnand: mpc5121: Use helper function devm_clk_get_enabled()
mtd: rawnand: lpc32xx_slc: Use helper function devm_clk_get_enabled()
mtd: rawnand: intel: Use helper function devm_clk_get_enabled()
mtd: rawnand: fsmc: Use helper function devm_clk_get_enabled()
mtd: rawnand: arasan: Use helper function devm_clk_get_enabled()
mtd: rawnand: qcom: Add read/read_start ops in exec_op path
mtd: rawnand: qcom: Clear buf_count and buf_start in raw read
mtd: maps: fix -Wvoid-pointer-to-enum-cast warning
mtd: rawnand: fix -Wvoid-pointer-to-enum-cast warning
mtd: rawnand: fsmc: handle clk prepare error in fsmc_nand_resume()
mtd: rawnand: Propagate error and simplify ternary operators for brcmstb_nand_wait_for_completion()
mtd: rawnand: qcom: Sort includes alphabetically
mtd: rawnand: qcom: Do not override the error no of submit_descs()
...
|
|
The mtd driver has similar problems than the one that was fixed in
commit dc3216b14160 ("super: ensure valid info").
The kill_mtd_super() helper calls shuts the superblock down but leaves
the superblock on fs_supers as the devices are still in use but puts the
mtd device and cleans out the superblock's s_mtd field.
This means another mounter can find the superblock on the list accessing
its s_mtd field while it is curently in the process of being freed or
already freed.
Prevent that from happening by keying superblock by dev_t just as we do
in the generic code.
Link: https://lore.kernel.org/linux-fsdevel/20230829-weitab-lauwarm-49c40fc85863@brauner
Acked-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Message-Id: <20230829-vfs-super-mtd-v1-2-fecb572e5df3@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Raw NAND core changes:
* Fix -Wvoid-pointer-to-enum-cast warning
* Export 'nand_exit_status_op()'
* dt-bindings: Fix nand-controller.yaml license
Raw NAND controller driver changes:
* Omap, Omap2, Samsung, Atmel, fsl_upm, lpc32xx_slc, lpc32xx_mlc, STM32_FMC2,
sh_ftlctl, MXC, Sunxi:
- Use devm_platform_get_and_ioremap_resource()
* Orion, vf610_nfc, Sunxi, STM32_FMC2, MTK, mpc5121, lpc32xx_slc, Intel,
FSMC, Arasan:
- Use helper function devm_clk_get_optional_enabled()
* Brcmnand:
- Use devm_platform_ioremap_resource_byname()
- Propagate init error -EPROBE_DEFER up
- Propagate error and simplify ternary operators
- Fix mtd oobsize
- Fix potential out-of-bounds access in oob write
- Fix crash during the panic_write
- Fix potential false time out warning
- Fix ECC level field setting for v7.2 controller
* fsmc: Handle clk prepare error in fsmc_nand_resume()
* Marvell: Add support for AC5 SoC
* Meson:
- Support for 512B ECC step size
- Fix build error
- Use NAND core API to check status
- dt-bindings:
* Make ECC properties dependent
* Support for 512B ECC step size
* Drop unneeded quotes
* Oxnas: Remove driver and bindings
* Qcom:
- Conversion to ->exec_op()
- Removal of the legacy interface
- Two full series of improvements/misc fixes
* Use the BIT() macro
* Use u8 instead of uint8_t
* Fix alignment with open parenthesis
* Fix the spacing
* Fix wrong indentation
* Fix a typo
* Early structure initialization
* Fix address parsing within ->exec_op()
* Remove superfluous initialization of "ret"
* Rename variables in qcom_op_cmd_mapping()
* Handle unsupported opcode in qcom_op_cmd_mapping()
* Fix the opcode check in qcom_check_op()
* Use EOPNOTSUPP instead of ENOTSUPP
* Wrap qcom_nand_exec_op() to 80 columns
* Unmap sg_list and free desc within submic_descs()
* Simplify the call to nand_prog_page_end_op()
* Do not override the error no of submit_descs()
* Sort includes alphabetically
* Clear buf_count and buf_start in raw read
* Add read/read_start ops in exec_op path
* vf610_nfc: Do not check 0 for platform_get_irq()
SPI-NAND changes:
* gigadevice: Add support for GD5F1GQ{4,5}RExxH
* esmt: Add support for F50D2G41KA
* toshiba: Add support for T{C,H}58NYG{0,2}S3HBAI4 and TH58NYG3S0HBAI6
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "err_irq".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-2-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get_optional() and clk_prepare_enable() can
now be replaced by devm_clk_get_optional_enabled() when driver enables
(and possibly prepares) the clocks for the whole lifetime of the device.
Moreover, it is no longer necessary to unprepare and disable the clocks
explicitly, so drop the label "no_dev".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-13-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "err_disable_clk".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "out_mod_clk_unprepare" and "out_ahb_clk_unprepare".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-10-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "err_clk_disable".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-9-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "clk_disable". And both mtk_nfc_enable_clk() and
mtk_nfc_disable_clk() now have a single user, which is the resume or
suspend callback, so drop this two helper function and just move related
operations in the resume or suspend function.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-8-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-7-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "unprepare_clk".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-6-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "err_disable_unprepare_clk".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-5-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly. The
label "disable_clk" no longer makes sense, rename it to "disable_fsmc".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-4-lizetao1@huawei.com
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly, so drop
the label "disable_bus_clk" and "disable_controller_clk".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230821031737.1973183-3-lizetao1@huawei.com
|
|
READ/READ_START opcodes are not set in exec_op path.
Fixing that here.
While there, Steps to program the controller is common for
erase/reset/read/program page. So use a common pattern and
pull them under one function.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230818145101.23825-4-quic_mdalam@quicinc.com
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174731.4059811-1-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Initialize buf_count and buf_start to 0 before starting the
raw read. If we will not initialize then read staus will get
updated with wrong value and we will see failure for even
successful raw read transaction.
Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230818145101.23825-3-quic_mdalam@quicinc.com
|
|
SPI NOR core changes:
* fix assumption on enabling quad mode in
spi_nor_write_16bit_sr_and_check()
* avoid setting SRWD bit in SR if WP# signal not connected as it will
configure the SR permanently as read only. Add "no-wp" dt property.
* clarify the need for spi-nor compatibles in dt-bindings
SPI NOR manufacturer drivers changes:
* spansion:
- add support for S28HS02GT
- switch methods to use vreg_offset from SFDP instead of hardcoding
the register value
* microchip/sst:
- add support for sst26vf032b flash
* winbond:
- correct flags for Winbond w25q128
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
When building with clang 18 I see the following warning:
| drivers/mtd/maps/physmap-versatile.c:209:25: warning: cast to smaller
| integer type 'enum versatile_flashprot' from 'const void *' [-Wvoid-pointer-to-enum-cast]
| 209 | versatile_flashprot = (enum versatile_flashprot)devid->data;
This is due to the fact that `devid->data` is a void* while `enum versatile_flashprot`
has the size of an int.
Cast `devid->data` to a uintptr_t to silence the above warning for clang
builds using W=1.
Link: https://github.com/ClangBuiltLinux/linux/issues/1910
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230816-void-drivers-mtd-maps-physmap-versatile-v2-1-433a25272bfa@google.com
|
|
When building with clang 18 I see the following warning:
| drivers/mtd/nand/raw/vf610_nfc.c:853:17: warning: cast to smaller integer
| type 'enum vf610_nfc_variant' from 'const void *' [-Wvoid-pointer-to-enum-cast]
| 853 | nfc->variant = (enum vf610_nfc_variant)of_id->data;
This is due to the fact that `of_id->data` is a void* while `enum vf610_nfc_variant`
has the size of an int.
Cast `of_id->data` to a uintptr_t to silence the above warning for clang
builds using W=1.
Link: https://github.com/ClangBuiltLinux/linux/issues/1910
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230817-void-drivers-mtd-nand-raw-vf610_nfc-v2-1-870a7c948c44@google.com
|
|
In fsmc_nand_resume(), the return value of clk_prepare_enable() should be
checked since it might fail.
Fixes: e25da1c07dfb ("mtd: fsmc_nand: Add clk_{un}prepare() support")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230817115839.10192-1-yiyang13@huawei.com
|
|
brcmstb_nand_wait_for_completion()
As bcmnand_ctrl_poll_status() return negative errno, so return true if
sts < 0. The < 0 case does not exist for wait_for_completion_timeout(),
so return true if sts = 0 and zero otherwise. Both of the true return
of them can be considered as a -ETIMEDOUT err, so return -ETIMEDOUT
if err is true to propagate err from its caller.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230808032943.3890545-1-ruanjinjie@huawei.com
|
|
Sort includes in alphabetical order.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Just use the error no returned by submit_descs() instead of overriding it
with -EIO.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-10-manivannan.sadhasivam@linaro.org
|
|
Now that the dma desc cleanup is moved inside submit_descs(), let's
simplify the call to nand_prog_page_end_op() inside qcom_nandc_write_page()
and qcom_nandc_write_page_raw() to match other functions.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-9-manivannan.sadhasivam@linaro.org
|
|
There are two types of dma descriptors being used in this driver allocated
by, prepare_bam_async_desc() and prep_adm_dma_desc() helper functions.
These functions map and prepare the descriptors to be used for dma
transfers.
And all the descriptors are submitted inside the submit_descs() function.
Once the transfer completion happens, those descriptors should be unmapped
and freed as a part of cleanup.
Currently, free_descs() function is doing the said cleanup of descriptors.
But the callers of submit_descs() are required to call free_descs() in both
the success and error cases.
Since there are no other transactions need to be done after submit_descs(),
let's just move the contents of free_descs() inside submit_descs() itself.
This makes sure that the cleanup is handled within the submit_descs()
thereby offloading the cleanup part from callers.
While at it, let's also rename the return variable from "r" to "ret".
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-8-manivannan.sadhasivam@linaro.org
|
|
Both the function arguments and the definition could be wrapped to 80
columns to save line space.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-7-manivannan.sadhasivam@linaro.org
|
|
Checkpatch complains over the usage of ENOTSUPP for new patches as below:
WARNING: ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP
So let's fix the error code which is already present in qcom_check_op().
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-6-manivannan.sadhasivam@linaro.org
|
|
qcom_check_op() function checks for the invalid opcode for the instruction
types. Currently, it just returns -ENOTSUPP for all opcodes of
NAND_OP_CMD_INSTR type due to the use of "||" operator instead of "&&".
Fix it!
This also fixes the following smatch warning:
drivers/mtd/nand/raw/qcom_nandc.c:3036 qcom_check_op() warn: was && intended here instead of ||?
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202308032022.SnXkKyFs-lkp@intel.com/
Fixes: 89550beb098e ("mtd: rawnand: qcom: Implement exec_op()")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-5-manivannan.sadhasivam@linaro.org
|
|
Handle the scenario where the caller has passed an unsupported opcode to
qcom_op_cmd_mapping(). In that case, log the error and return the
-EOPNOTSUPP errono. Also, let's propagate this error code all the way up.
This also fixes the following smatch warning:
drivers/mtd/nand/raw/qcom_nandc.c:2941 qcom_op_cmd_mapping() error: uninitialized symbol 'ret'.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202308032022.SnXkKyFs-lkp@intel.com/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-4-manivannan.sadhasivam@linaro.org
|
|
qcom_op_cmd_mapping() function accepts opcode and returns the corresponding
command register. So let's rename the local variables and parameters to
reflect the same.
Reported-by: Miquel Raynal <miquel.raynal@bootlin.com>
Closes: https://lore.kernel.org/all/20230804190750.3367a044@xps-13/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-3-manivannan.sadhasivam@linaro.org
|
|
In all the cases, "ret" variable is assigned a value before returning it.
So there is no need to explicitly initialize it with 0.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230805174146.57006-2-manivannan.sadhasivam@linaro.org
|
|
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enable (and possibly
prepare) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clock explicitly, so drop
the label "dis_clks" and "dis_clk_reg".
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230818074642.308166-12-lizetao1@huawei.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
|
|
Describe this new part. The datasheet is public.
Link: https://ww1.microchip.com/downloads/aemDocuments/documents/MPD/ProductDocuments/DataSheets/SST26VF032B-SST26VF032BA-2.5V-3.0V-32-Mbit-Serial-Quad-IO-%28SQI%29-Flash-Memory-20005218K.pdf
Here are the sfdp tables plus base testing to show it works.
$ cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
sst26vf032b
$ cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
bf2642
$ cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
sst
$ xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp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$ md5sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
e7efddddb3d5ee89ca37bf6b6e789645 /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
$ dd if=/dev/urandom of=./qspi_test bs=1M count=1
1+0 records in
1+0 records out
$ mtd_debug write /dev/mtd0 0 1048576 qspi_test
Copied 1048576 bytes from qspi_test to address 0x00000000 in flash
$ mtd_debug erase /dev/mtd0 0 1048576
Erased 1048576 bytes from address 0x00000000 in flash
$ mtd_debug read /dev/mtd0 0 1048576 qspi_read
Copied 1048576 bytes from address 0x00000000 in flash to qspi_read
$ hexdump qspi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0100000
$ mtd_debug write /dev/mtd0 0 1048576 qspi_test
Copied 1048576 bytes from qspi_test to address 0x00000000 in flash
$ mtd_debug read /dev/mtd0 0 1048576 qspi_read
Copied 1048576 bytes from address 0x00000000 in flash to qspi_read
$ sha1sum qspi_test qspi_read
2f2f191c7a937eca5db21a1c39e79e7327587cc1 qspi_test
2f2f191c7a937eca5db21a1c39e79e7327587cc1 qspi_read
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230808075001.223150-1-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
|
|
spi_nor_write_16bit_sr_and_check() should also check if bus width is
4 before setting QE bit.
Fixes: 39d1e3340c73 ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Suggested-by: Michael Walle <michael@walle.cc>
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230818064524.1229100-2-hsinyi@chromium.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
|
|
Since platform_get_irq() never returned zero, so it need not to check
whether it returned zero, and we use the return error code of
platform_get_irq() to replace the current return error code, for that
platform_get_irq() may return -EINVAL or -ENXIO.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230803085056.30888-1-wangzhu9@huawei.com
|
|
Convert platform_get_resource_byname() + devm_ioremap_resource() to a
single call to devm_platform_ioremap_resource_byname(), as this is
exactly what this function does.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230802013500.1030853-1-lizetao1@huawei.com
|
|
The logic is way too convoluted, let's clean the kref_get/put section to
clarify what this block does when using CONFIG_MTD_PARTITIONED_MASTER:
- Iterate through all the parent mtd devices
- Grab a reference over them all but the master
- Only grab the master whith CONFIG_MTD_PARTITIONED_MASTER
Same logic must apply in the put path, otherwise it would be broken.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Alexander Usyskin <alexander.usyskin@intel.com>
Cc: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Fixes: 19bfa9ebebb5 ("mtd: use refcount to prevent corruption")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Alexander Usyskin <alexander.usyskin@intel.com>
Link: https://lore.kernel.org/linux-mtd/20230731090903.770277-1-miquel.raynal@bootlin.com
|
|
I case of partition device_unregister() in mtd_device_release()
calls mtd_release() which frees mtd_info structure for partition.
All code after device_unregister in mtd_device_release thus
uses already freed memory.
Move part of code to mtd_release() and restict mtd->dev cleanup
to non-partion object.
For partition object such cleanup have no sense as partition
mtd_info is removed.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Fixes: 19bfa9ebebb5 ("mtd: use refcount to prevent corruption")
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230731115836.542747-1-alexander.usyskin@intel.com
|
|
Fixes the following build error:
drivers/mtd/nand/raw/meson_nand.c:244:59: error: initializer element is not a compile-time constant
static const struct nand_ecc_step_info axg_stepinfo[] = { axg_stepinfo_1024, axg_stepinfo_512 };
^~~~~~~~~~~~~~~~~
Fixes: 0e1db39336d8 ("mtd: rawnand: meson: support for 512B ECC step size")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307281007.MMuVjmJ9-lkp@intel.com/
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230728093810.2985324-1-AVKrasnov@sberdevices.ru
|
