Age | Commit message (Collapse) | Author | Files | Lines |
|
Instead of leaving the Rx timestamps in the same mode as before if we
disable the Rx logic, we can set it into a mode that has the fewest
possible timestamps generated. To do this, select only V1 mode, but do
not enable UDP packet recognition. This should eliminate all (or at
least almost all) Rx timestamps, since V1 packets are always over UDP.
Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It's possible that the user configured only Tx hardware timestamping,
and thus we might be receiving PTP traffic which we timestamp but which
software never reads. In this case we don't want to check for Rx
timestamp hang, because we already know that software won't be handling
them. Thus, we add the same check against pf->ptp_rx as we have in the
Rx timestamp code path.
Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We should not be doing Tx or Rx timestamps if we do not have PTP
enabled. Add checks to ensure that we don't attempt to handle any PTP
related timestamping code if we have not enabled PTP on that PF.
Change-ID: I4335942ae2d5c5f91abfdbeeea02bcace49e7677
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Resolve an issue related to images with multiple PFs per physical
port. We cannot fully support 1588 PTP features, since only one port
should control (ie: write) the registers at a time. Doing so can cause
interference of functionality.
It may be possible to partially implement the API for only those
features without side effects. However, this at minimum means non
controlling PFs lose Tx timestamps, frequency atunement, and possibly
SYSTIME adjustment. There may be further impact I did not discover.
Since the API in the kernel expects these features to work, it is
simpler and less dangerous to just disable PTP features on all PFs not
identified as the controlling PF in PRTTSYN_CTL0.PF_ID.
This change also removes the warning printed when hwtstaml IOCTL is
called on the wrong PF. This is actually meaningless now, since only one
PF per port will support it. In addition, the ethtool get_ts_info IOCTL
was updated so that only the controlling port will even indicate support
(so as not to confuse users).
The overall downside is complete loss of functionality on non
controlling PF, vs the possible gain of partial support. The biggest
factor for choosing this approach is simplicity and ensuring that the
main PF will work. There could easily be other portions of the 1588
logic with side effects I am not aware, and the reduced functionality
that might be made available is significantly less useful. In addition,
the API does not allow for proper indication of why particular features
are not supported. These reasons are enough to decide for the simpler
approach to resolving this issue.
Change-ID: If4696bae686fc18aef6552b67dd417213d987c16
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Only warn once that PTP is not supported when linked at 100Mbit.
Yes, using a static this way means that this once-only message is not
port specific, but once only for the life of the driver, regardless of
the number of ports. That should be plenty.
Change-ID: Ie6476530056df408452e195ef06afd4f57caa4b2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The receive hang detection routine was never being run when
PTP was enabled.
Change-ID: I200f35b0f3190d31b595df89d678f4c8a2131ba0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Display a verbose warning message when the incorrect PF attempts to
control timestamping for a port to which it was not assigned. This
shouldn't display except in the case of multiple PFs per port. The
primary intent of this message is to help debugging the reason why the
SIOCSHWTSTAMP ioctl has failed, and to help narrow the cause of the
issue.
Change-ID: Ic98798e0c844d98389d4c20e7160ba256f2bc7e8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i40e has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We don't need the export.h header so we can just go ahead and remove it.
Change-ID: I9057396b141ee449d8299409081358b9270a7c4d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently every time we run through the i40e_ptp_init routine, we create
a new device node. This function is called by i40e_reset_and_rebuild
which is used to handle reset of the device. Even though the 1588
registers only get cleared on a GLOBAL reset, this function is still
called to handle a CORE reset.
This causes a leak of PTP device nodes at every reset. To fix this,
break PTP device clock node creation out of i40e_ptp_init, and only call
this if we don't already have a device created. Further invocation of
i40e_ptp_init will not generate new PTP devices. Instead, only the
necessary work required to reconfigure 1588 will be done.
This change also fixes an issue where a reset can cause the
device to forget it's timestamp configuration, and revert to the default
mode.
Change-ID: I741d01c61d9fe1d24887859d1316e1a8a892909e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch prevents the SIOCGHWTSTAMP ioctl from possibly returning bad
data, by not permanently storing the setting into the private
structure until after we've finished validating that we can support it.
Change-ID: Ib59f9b4f73f451d5a2e76fb8efa5d4271b218433
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch facilitates future work by breaking the PTP hardware control
bits out of the i40e_set_ts_config function. By doing this, we can
maintain state about the 1588 timestamping mode and properly re-enable
to the last known mode during a re-initialize of 1588 bits.
This patch also modifies i40e_ptp_init to call the
i40e_ptp_set_timestamp_mode during the reconfiguration process. A
future patch will ensure that the hwtstamp_config structure is not reset
during this process, so that timestamp mode will be maintained across a
reset.
Change-ID: Ic20832c96c5c512ac203b6c7534e10d891c560f0
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Reduces possible confusion and ambiguity in purpose of the ancillary
feature control entry point function.
Change-ID: I21d773c1a86878f6d061505185b596c788d1b7cc
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The previous removal of the PTP Tx work functionality was
incomplete as noted by Jake Keller. This removal allows
us to rely on the Tx timesync interrupt.
CC: Jacob Keller <jacob.e.keller@intel.com>
Change-ID: Id4faaf275a3688053ebbf07bef08072f9fd11aa9
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch removes the unnecessary ptp_tx_work item. It conflicts with
the interrupt-based handler, and will cause spurious warning messages to
be displayed in the kernel log. Since the hardware can properly trigger
an interrupt, we do not need to poll for an available timestamp in a
work queue any more.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add \n at the end of messages where missing, remove all \r.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
New feature: Enable PTP support in the i40e driver.
Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|