Age | Commit message (Collapse) | Author | Files | Lines |
|
There are 2 issues with the blamed commit.
1. When the phy is initialized, it would enable the disabled of UDPv4
checksums. The UDPv6 checksum is already enabled by default. So when
1-step is configured then it would clear these flags.
2. After the 1-step is configured, then if 2-step is configured then the
1-step would be still configured because it is not clearing the flag.
So the sync frames will still have origin timestamps set.
Fix this by reading first the value of the register and then
just change bit 12 as this one determines if the timestamp needs to
be inserted in the frame, without changing any other bits.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may
return NULL as ptp_header due to abnormal packet type or corrupted packet.
Fix this bug by adding ptp_header check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On reworking and splitting the at803x driver, in splitting function of
at803x PHYs it was added a NULL dereference bug where priv is referenced
before it's actually allocated and then is tried to write to for the
is_1000basex and is_fiber variables in the case of at8031, writing on
the wrong address.
Fix this by correctly setting priv local variable only after
at803x_probe is called and actually allocates priv in the phydev struct.
Reported-by: William Wortel <wwortel@dorpstraat.com>
Cc: <stable@vger.kernel.org>
Fixes: 25d2ba94005f ("net: phy: at803x: move specific at8031 probe mode check to dedicated probe")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240325190621.2665-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec732951702 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Merge in late fixes to prepare for the 6.9 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Handling case err == 0 in the other branch allows to simplify the
code. In addition I assume in "err & phydev->eee_cfg.tx_lpi_enabled"
it should have been a logical and operator. It works as expected also
with the bitwise and, but using a bitwise and with a bool value looks
ugly to me.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/de37bf30-61dd-49f9-b645-2d8ea11ddb5d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240307122346.3677534-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240307122231.3677241-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The logic for enabling the TX clock shift is inverse of enabling the RX
clock shift. The TX clock shift is disabled when DP83822_TX_CLK_SHIFT is
set. Correct the current behavior and always write the delay configuration
to ensure consistent delay settings regardless of bootloader configuration.
Reference: https://www.ti.com/lit/ds/symlink/dp83822i.pdf p. 69
Fixes: 8095295292b5 ("net: phy: DP83822: Add setting the fixed internal delay")
Signed-off-by: Tim Pambor <tp@osasysteme.de>
Link: https://lore.kernel.org/r/20240305110608.104072-1-tp@osasysteme.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec913b ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comment in m88e1111_config_init_1000basex() is wrong - it claims
that Autoneg will be enabled, but this doesn't actually happen.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1rhos4-003yuQ-5p@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Kernel bot has discovered that if CONFIG_GPIOLIB is not set compilation
will fail.
Upon investigation the issue is that qca807x_gpio() is guarded by a
preprocessor check but then it is called under
if (IS_ENABLED(CONFIG_GPIOLIB)) in the probe call so the compiler will
error out since qca807x_gpio() has not been declared if CONFIG_GPIOLIB has
not been set.
Fixes: d1cb613efbd3 ("net: phy: qcom: add support for QCA807x PHY Family")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202403031332.IGAbZzwq-lkp@intel.com/
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20240305142113.795005-1-robimarko@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order for EEE to operate, both the MAC and the PHY need to support
it, similar to how pause works. With some exception - a number of PHYs
have SmartEEE or AutoGrEEEn support in order to provide some EEE-like
power savings with non-EEE capable MACs.
Copy the pause concept and add the call phy_support_eee() which the MAC
makes after connecting the PHY to indicate it supports EEE. phylib will
then advertise EEE when auto-neg is performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MAC driver changes its EEE hardware configuration in its
adjust_link callback. This is called when auto-neg
completes. Disabling EEE via eee_enabled false will trigger an
autoneg, and as a result the adjust_link callback will be called with
phydev->enable_tx_lpi set to false. Similarly, eee_enabled set to true
and with a change of advertised link modes will result in a new
autoneg, and a call the adjust_link call.
If set_eee is called with only a change to tx_lpi_enabled which does
not trigger an auto-neg, it is necessary to call the adjust_link
callback so that the MAC is reconfigured to take this change into
account.
When setting phydev->enable_tx_lpi, take both eee_enabled and
tx_lpi_enabled into account, so the MAC drivers just needs to act on
phydev->enable_tx_lpi and not the whole EEE configuration.
The same check should be done for tx_lpi_timer too.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240302195306.3207716-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Have phylib keep track of the EEE configuration. This simplifies the
MAC drivers, in that they don't need to store it.
Future patches to phylib will also make use of this information to
further simplify the MAC drivers.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
MAC drivers which support EEE need to know the results of the EEE
auto-neg in order to program the hardware to perform EEE or not. The
oddly named phy_init_eee() can be used to determine this, it returns 0
if EEE should be used, or a negative error code,
e.g. -EOPPROTONOTSUPPORT if the PHY does not support EEE or negotiate
resulted in it not being used.
However, many MAC drivers get this wrong. Add phydev->enable_tx_lpi
which indicates the result of the autoneg for EEE, including if EEE is
administratively disabled with ethtool. The MAC driver can then access
this in the same way as link speed and duplex in the adjust link
callback. If enable_tx_lpi is true, the MAC should send low power
indications and does not need to consider anything else with respect
to EEE.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the length of the cable is more than 100m and the lan8814 is
configured to run in 1000Base-T Slave then the register of the device
needs to be optimized.
Workaround this by setting the measure time to a value of 0xb. This
value can be set regardless of the configuration.
This issue is described in 'LAN8814 Silicon Errata and Data Sheet
Clarification' and according to that, this will not be corrected in a
future silicon revision.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240304091548.1386022-3-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Lan8814 phy led behavior is not correct. It was noticed that the led
still remains ON when the cable is unplugged while there was traffic
passing at that time.
The fix consists in clearing bit 10 of register 0x38, in this way the
led behaviour is correct and gets OFF when there is no link.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240304091548.1386022-2-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently QCA808x driver does not fill the possible_interfaces.
2.5G QCA808x support SGMII and 2500Base-X while 1G model only supports
SGMII, so fill the possible_interfaces accordingly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 2 versions of QCA808x, one 2.5G capable and one 1G capable.
Currently, this matter only in the .get_features call however, it will
be required for filling supported interface modes so lets add a helper
that can be reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d1d77120bc28 ("net: phy: dp83826: support TX data voltage tuning")
introduced a regression in that WOL is not disabled by default for DP83826.
WOL should normally be enabled through ethtool.
Fixes: d1d77120bc28 ("net: phy: dp83826: support TX data voltage tuning")
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Link: https://lore.kernel.org/r/20240226162339.696461-1-catalin.popescu@leica-geosystems.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify the function, no functional change intended.
- Remove not needed variable unsupp, I think code is even better
readable now.
- Move setting phydev->eee_enabled out of the if clause
- Simplify return value handling
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/442277c7-7431-4542-80b5-1d3d691714d7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The TI DP83826 PHY can operate between two RMII modes:
- master mode (PHY operates from a 25MHz clock reference)
- slave mode (PHY operates from a 50MHz clock reference)
By default, the operation mode is configured by hardware straps.
Add support to configure the operation mode from within the driver.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TI DP83826 PHY can operate in either MII mode or RMII mode.
By default, it is configured by straps.
It can also be configured by writing to the bit 5 of register 0x17 - RMII
and Status Register (RCSR).
When phydev->interface is rmii, rmii mode must be enabled, otherwise
mii mode must be set.
This prevents misconfiguration of hw straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/ipv4/udp.c
f796feabb9f5 ("udp: add local "peek offset enabled" flag")
56667da7399e ("net: implement lockless setsockopt(SO_PEEK_OFF)")
Adjacent changes:
net/unix/garbage.c
aa82ac51d633 ("af_unix: Drop oob_skb ref before purging queue in GC.")
11498715f266 ("af_unix: Remove io_uring code for GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit bb726b753f75 ("net: phy: realtek: add support for
RTL8211F(D)(I)-VD-CG") extended support of the driver from the existing
support for RTL8211F(D)(I)-CG PHY to the newer RTL8211F(D)(I)-VD-CG PHY.
While that commit indicated that the RTL8211F_PHYCR2 register is not
supported by the "VD-CG" PHY model and therefore updated the corresponding
section in rtl8211f_config_init() to be invoked conditionally, the call to
"genphy_soft_reset()" was left as-is, when it should have also been invoked
conditionally. This is because the call to "genphy_soft_reset()" was first
introduced by the commit 0a4355c2b7f8 ("net: phy: realtek: add dt property
to disable CLKOUT clock") since the RTL8211F guide indicates that a PHY
reset should be issued after setting bits in the PHYCR2 register.
As the PHYCR2 register is not applicable to the "VD-CG" PHY model, fix the
rtl8211f_config_init() function by invoking "genphy_soft_reset()"
conditionally based on the presence of the "PHYCR2" register.
Fixes: bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220070007.968762-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move interrupt configuration from mv88q222x_revb0_config_init to
mv88q2xxx_config_init. Same register and bits are used for the 88q2xxx
devices.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Stefan Eichenberger <eichest@gmail.com>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-15-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove assignment of phydev->pma_extable in mv88q222x_revb0_config_init.
It is already done in mv88q2xxx_config_init, just call
mv88q2xxx_config_init.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-14-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mv88q2xxx_config_init calls genphy_c45_read_pma which is done by
mv88q2xxx_read_status, it calls also mv88q2xxx_config_aneg which is
also called by the PHY state machine. Let the PHY state machine handle
the phydriver ops in their intendend way.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Eichenberger <eichest@gmail.com>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-13-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Switch to mv88q2xxx_config_aneg for Marvell 88Q2220 devices and remove
the mv88q222x_config_aneg function which is basically a copy of the
mv88q2xxx_config_aneg function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-12-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Marvell 88Q2xxx devices follow the same scheme, after configuration they
need a soft reset. Soft resets differ between devices, so we use the
.soft_reset callback instead of creating .config_aneg callbacks for each
device.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-11-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add cable test support for Marvell 88Q222x devices. Reported distance
granularity is 1m.
1m cable, open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair A code Open Circuit
Pair A, fault length: 1.00m
1m cable, shorted:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair A code Short within Pair
Pair A, fault length: 1.00m
6m cable, open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair A code Open Circuit
Pair A, fault length: 6.00m
6m cable, shorted:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair A code Short within Pair
Pair A, fault length: 6.00m
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240218075753.18067-10-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Marvell 88q2xxx devices have an inbuilt temperature sensor. Add hwmon
support for this sensor.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-9-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add suspend/resume ops for Marvell 88Q2xxx devices.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-8-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Added .config_intr and .handle_interrupt callbacks. Whenever the link
goes up or down an interrupt will be triggered. Interrupts are configured
separately for 100/1000BASET1.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-7-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a driver for the Marvell 88Q2220. This driver allows to detect the
link, switch between 100BASE-T1 and 1000BASE-T1 and switch between
master and slave mode. Autonegotiation is supported.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregor Herburger <gregor.herburger@ew.tq-group.com>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-6-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename mv88q2xxxx_get_sqi to mv88q2xxx_get_sqi and
mv88q2xxxx_get_sqi_max to mv88q2xxx_get_sqi_max.
Fix linebreaks and use everywhere hexadecimal numbers written with
lowercase letters instead of mixing it up.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-5-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set 100BT1 and 1000BT1 linkmode advertisement bits to adv_l_mask to
enable detection.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240218075753.18067-4-dima.fedrau@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fill in the possible_interfaces member.
GPY21x phys support the SGMII and 2500base-X interfaces
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Link: https://lore.kernel.org/r/20240216054435.22380-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Aquantia AQR813 is the Octal Port variant of the AQR113. Add PHY ID for
it to provide support for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for handling the EEE advertisement 2 register.
For now only 2500baseT and 5000baseT modes are supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
genphy_c45_read_eee_lpa
Add support for reading EEE link partner ability 2 register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add and use genphy_c45_read_eee_cap2(), complementing
genphy_c45_read_eee_cap1().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a prerequisite for adding EEE CAP2 register support, complement
PHY_EEE_CAP1_FEATURES with PHY_EEE_CAP2_FEATURES.
For now only 2500baseT and 5000baseT modes are supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Aquantia AQR113 PHY ID. Aquantia AQR113 is just a chip size variant of
the already supported AQR133C where the only difference is the PHY ID
and the hw chip size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/dev.c
9f30831390ed ("net: add rcu safety to rtnl_prop_list_size()")
723de3ebef03 ("net: free altname using an RCU callback")
net/unix/garbage.c
11498715f266 ("af_unix: Remove io_uring code for GC.")
25236c91b5ab ("af_unix: Fix task hung while purging oob_skb in GC.")
drivers/net/ethernet/renesas/ravb_main.c
ed4adc07207d ("net: ravb: Count packets instead of descriptors in GbEth RX path"
)
c2da9408579d ("ravb: Add Rx checksum offload support for GbEth")
net/mptcp/protocol.c
bdd70eb68913 ("mptcp: drop the push_pending field")
28e5c1380506 ("mptcp: annotate lockless accesses around read-mostly fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the PHY MDIO helpers.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240214152741.670178-7-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit d492cc2573a0 ("driver core: device.h: make struct
bus_type a const *"), the driver core can properly handle constant
struct bus_type, move the mdio_bus_type variable to be a constant
structure as well, placing it into read-only memory which can not be
modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240213-bus_cleanup-mdio-v1-1-f9e799da7fda@marliere.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add Aquantia AQR111 and AQR111B0 PHY ID. These PHY advertise 10G speed
but actually supports up to 5G speed, hence some manual fixup is needed.
The Aquantia AQR111B0 PHY is just a variant of the AQR111 with smaller
chip size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240213133558.1836-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, we are checking whether the PHY package mode matches the
individual PHY interface modes at PHY package probe time, but at that time
we only know the PHY package mode and not the individual PHY interface
modes as of_get_phy_mode() that populates it will only get called once the
netdev to which PHY-s are attached to is being probed and thus this check
will always fail and return -EINVAL.
So, lets move this check to .config_init_once as at that point individual
PHY interface modes should be populated.
Fixes: d1cb613efbd3 ("net: phy: qcom: add support for QCA807x PHY Family")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240212115043.1725918-1-robimarko@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|