summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath11k/qmi.h
AgeCommit message (Collapse)AuthorFilesLines
2023-11-30wifi: ath11k: Update Qualcomm Innovation Center, Inc. copyrightsJeff Johnson1-1/+1
Update the copyright for all ath11k files modified on behalf of Qualcomm Innovation Center, Inc. in 2021 through 2023. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20231128-ath12kcopyrights-v1-2-be0b7408cbac@quicinc.com
2023-08-23wifi: ath11k: Remove unused declarationsYue Haibing1-2/+0
Commit 2c3960c2253d ("ath11k: setup ce tasklet for control path") declared but never implemented ath11k_ce_map_service_to_pipe(). Commit e3396b8bddd2 ("ath11k: ce: support different CE configurations") declared but never implemented ath11k_ce_attr_attach(). Commit d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") declared but never implemented ath11k_qmi_event_work()/ath11k_qmi_msg_recv_work(). Signed-off-by: Yue Haibing <yuehaibing@huawei.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230811104413.33668-1-yuehaibing@huawei.com
2023-08-02wifi: ath11k: Add coldboot calibration support for QCN9074Anilkumar Kolli1-1/+2
QCN9074 supports 6 GHz, which has increased number of channels compared to 5 GHz/2 GHz. So, to support coldboot calibration in QCN9074 ATH11K_COLD_BOOT_FW_RESET_DELAY extended to 60 seconds. To avoid code redundancy, fwreset_from_cold_boot moved to QMI and made common for both ahb and pci. Coldboot calibration is enabled only in FTM mode for QCN9074. QCN9074 requires firmware restart after coldboot, hence enable cbcal_restart_fw in hw_params. This support can be enabled/disabled using hw params for different hardware. Currently it is not enabled for QCA6390. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com> Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230726141032.3061-3-quic_rajkbhag@quicinc.com
2022-11-02wifi: ath11k: Fix QCN9074 firmware boot on x86Tyler J. Stachecki1-1/+1
The 2.7.0 series of QCN9074's firmware requests 5 segments of memory instead of 3 (as in the 2.5.0 series). The first segment (11M) is too large to be kalloc'd in one go on x86 and requires piecemeal 1MB allocations, as was the case with the prior public firmware (2.5.0, 15M). Since f6f92968e1e5, ath11k will break the memory requests, but only if there were fewer than 3 segments requested by the firmware. It seems that 5 segments works fine and allows QCN9074 to boot on x86 with firmware 2.7.0, so change things accordingly. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16 Signed-off-by: Tyler J. Stachecki <stachecki.tyler@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20221022042728.43015-1-stachecki.tyler@gmail.com
2022-09-01wifi: ath11k: Fix incorrect QMI message ID mappingsManikanta Pubbisetty1-2/+8
QMI message IDs for some of the QMI messages were incorrectly defined in the original implementation. These have to be corrected to enable cold boot support on WCN6750. These corrections are applicable for all chipsets and will not impact them. Refactor the code accordingly. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220720134909.15626-2-quic_mpubbise@quicinc.com
2022-05-10ath11k: Reuse the available memory after firmware reloadAnilkumar Kolli1-0/+2
Ath11k allocates memory when firmware requests memory in QMI. Coldboot calibration and firmware recovery uses firmware reload. On firmware reload, firmware sends memory request again. If Ath11k allocates memory on first firmware boot, reuse the available memory. Also check if the segment type and size is same on the next firmware boot. Reuse if segment type/size is same as previous firmware boot else free the segment and allocate the segment with size/type. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00752-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220506141448.10340-1-quic_akolli@quicinc.com
2022-05-02ath11k: Fetch device information via QMI for WCN6750Manikanta Pubbisetty1-4/+20
Since WPPS Q6 does the PCIe enumeration of WCN6750, device information like BAR and BAR size is not known to the APPS processor (Application Processor SubSystem). In order to fetch these details, a QMI message called device info request will be sent to the target. Therefore, add logic to fetch BAR details from the target. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-6-quic_mpubbise@quicinc.com
2022-05-02ath11k: Add HW params for WCN6750Manikanta Pubbisetty1-0/+2
WCN6750 is a PCIe based solution that is attached to and enumerated by the WPSS (Wireless Processor SubSystem) Q6 processor. Though it is a PCIe device, since it is not attached to APSS processor (Application Processor SubSystem), APSS will be unaware of such a decice and hence it is registered to the APSS processor as a platform device(AHB). Because of this hybrid nature, it is called as a hybrid bus device. A new variable hybrid_bus_type is defined in hw_params to indicate the hybrid nature of the device. Add HW params for WCN6750. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220429170502.20080-4-quic_mpubbise@quicinc.com
2022-02-21ath11k: add ath11k_qmi_free_resource() for recoveryWen Gong1-0/+1
ath11k_qmi_free_target_mem_chunk() and ath11k_qmi_m3_free() is static in qmi.c, they are needed for recovery, export them in a new function. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220209060012.32478-2-quic_wgong@quicinc.com
2021-12-22ath11k: add support of firmware logging for WCN6855Cheng Wang1-0/+12
Host enables WMI firmware logging feature via QMI message. Host receives firmware logging messages on WMI_DIAG_EVENTID, then sends logging messages to user space via event tracing infrastructure. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by: Cheng Wang <quic_chengwan@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211220121053.357087-1-quic_chengwan@quicinc.com
2021-12-21ath11k: add regdb.bin download for regdb offloadWen Gong1-0/+1
The regdomain is self-managed type for ath11k, the regdomain info is reported from firmware, it is not from wireless regdb. Firmware fetch the regdomain info from board data file before. Currently most of the regdomain info has moved to another file regdb.bin from board data file for some chips such as QCA6390 and WCN6855, so the regdomain info left in board data file is not enough to support the feature which need more regdomain info. After download regdb.bin, firmware will fetch the regdomain info from regdb.bin instead of board data file and report to ath11k. If it does not have the file regdb.bin, it also can initialize wlan success and firmware then fetch regdomain info from board data file. Add download the regdb.bin before download board data for some specific chip which support supports_regdb in hardware parameters. download regdb.bin log: [430082.334162] ath11k_pci 0000:05:00.0: chip_id 0x2 chip_family 0xb board_id 0x106 soc_id 0x400c0200 [430082.334169] ath11k_pci 0000:05:00.0: fw_version 0x110c8b4c fw_build_timestamp 2021-10-25 07:41 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02892-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 [430082.334414] ath11k_pci 0000:05:00.0: boot firmware request ath11k/WCN6855/hw2.0/regdb.bin size 24310 output of "iw reg get" global country US: DFS-FCC (2402 - 2472 @ 40), (N/A, 30), (N/A) (5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW (5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW (5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS (5735 - 5835 @ 80), (N/A, 30), (N/A) (57240 - 63720 @ 2160), (N/A, 40), (N/A) phy#0 (self-managed) country US: DFS-FCC (2402 - 2472 @ 40), (6, 30), (N/A) (5170 - 5250 @ 80), (N/A, 24), (N/A), AUTO-BW (5250 - 5330 @ 80), (N/A, 24), (0 ms), DFS, AUTO-BW (5490 - 5730 @ 160), (N/A, 24), (0 ms), DFS, AUTO-BW (5735 - 5895 @ 160), (N/A, 30), (N/A), AUTO-BW (5945 - 7125 @ 160), (N/A, 24), (N/A), NO-OUTDOOR, AUTO-BW Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211220062355.17021-1-quic_wgong@quicinc.com
2021-12-16ath11k: Use reserved host DDR addresses from DT for PCI devicesAnilkumar Kolli1-0/+1
Host DDR memory (contiguous 45 MB in mode-0 or 15 MB in mode-2) is reserved through DT entries for firmware usage. Send the base address from DT entries. If DT entry is available, PCI device will work with fixed_mem_region else host allocates multiple segments. IPQ8074 on HK10 board supports multiple PCI devices. IPQ8074 + QCN9074 is tested with this patch. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/1638789319-2950-2-git-send-email-akolli@codeaurora.org
2021-12-14ath11k: Change qcn9074 fw to operate in mode-2Seevalamuthu Mariappan1-1/+0
In mode-2 QCN9074 firmware uses 15MB of host memory and firmware request 1MB size segements in QMI, whereas in mode-0 firmware uses 45MB of host memory and each segment is of 2MB size. In mode-2 firmware operates with reduced number of vdevs and peers. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1 Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org> Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20211209104351.9811-3-kvalo@kernel.org
2021-12-07ath11k: Fix QMI file type enum valueSeevalamuthu Mariappan1-1/+1
bdf_type for caldata in QMI_WLANFW_BDF_DOWNLOAD_REQ_V01 is wrongly sent as 1. But, expected bdf_type value for caldata and EEPROM is 2 and 3 respectively. It leads to firmware crash. Fix ath11k_qmi_file_type enum values. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 Fixes: 336e7b53c82f ("ath11k: clean up BDF download functions") Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/1638182754-18408-1-git-send-email-quic_seevalam@quicinc.com
2021-09-28ath11k: add caldata download support from EEPROMAnilkumar Kolli1-3/+13
Firmware updates EEPROM support capability in QMI FW caps, send QMI BDF download request message with file type EEPROM, to get caldata download from EEPROM. Firmware takes more time to update cal data from EEPROM, so increase QMI timeout. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210721201927.100369-5-jouni@codeaurora.org
2021-09-28ath11k: use hw_params to access board_size and cal_offsetAnilkumar Kolli1-2/+0
Reuse board_size from hw_params, add cal_offset to hw params. This patch is clean up only, there is no change in functionality. cal_size was unused, so remove that. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210721201927.100369-2-jouni@codeaurora.org
2021-02-17ath11k: Add qcn9074 mhi controller configAnilkumar Kolli1-0/+1
Add MHI config for QCN9074 also populate ath11k_hw_params for QCN9074. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1612946530-28504-6-git-send-email-akolli@codeaurora.org
2021-02-17ath11k: Update memory segment count for qcn9074Anilkumar Kolli1-0/+2
QCN9074 FW requests three types memory segments during the boot, qmi mem seg type 1 of size 15728640 qmi mem seg type 4 of size 3735552 qmi mem seg type 3 of size 1048576 Segment type 3 is for M3 coredump memory. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1612946530-28504-5-git-send-email-akolli@codeaurora.org
2021-02-17ath11k: qmi: increase the number of fw segmentsAnilkumar Kolli1-3/+3
QCN9074 firmware uses 20MB of HOST DDR memory, fw requests the memory in segmnets of size 1MB/512KB/256KB. Increase the number of fw memory segments to 52. Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1 Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1612946530-28504-4-git-send-email-akolli@codeaurora.org
2020-12-18ath11k: qmi: try to allocate a big block of DMA memory firstCarl Huang1-0/+1
Not all firmware versions support allocating DMA memory in smaller blocks so first try to allocate big block of DMA memory for QMI. If the allocation fails, let firmware request multiple blocks of DMA memory with smaller size. This also fixes an unnecessary error message seen during ath11k probe on QCA6390: ath11k_pci 0000:06:00.0: Respond mem req failed, result: 1, err: 0 ath11k_pci 0000:06:00.0: qmi failed to respond fw mem req:-22 Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1608127593-15192-1-git-send-email-kvalo@codeaurora.org
2020-11-07ath11k: cold boot calibration supportGovindaraj Saminathan1-0/+3
cold boot calibration is the process to calibrate all the channels during the boot-up to avoid the calibration delay during the channel change. During the boot-up, firmware started in cold boot calibration mode Firmware calibrate all channels and generate CalDb(DDR). Subsequent wifi bringup will reuse the same CalDb. Firmware is restarted in normal mode to continue the normal operation. caldb memory address send to firmware through the QMI message.Firmware use this address to store the caldb data and use it until next reboot. This will give the improvement during the channel change. But it is increasing the boot-up time(up to 15sec depend on number of radios). So if the user want to reduce the boot-up time and accepting for channel change delay, user can disable this feature using the module param cold_boot_cal=0. Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1 Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org> Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org> Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org
2020-11-07ath11k: search DT for qcom,ath11k-calibration-variantSven Eckelmann1-0/+2
Board Data File (BDF) is loaded upon driver boot-up procedure. The right board data file is identified on IPQ6018 using bus, qmi-chip-id and qmi-board-id. The problem, however, can occur when the (default) board data file cannot fulfill with the vendor requirements and it is necessary to use a different board data file. This problem was already solved on ath10k by adding a ",variant=.*" at the end of the board name. The same functionality must also be provided for ath11k. The device tree requires an additional string to define the variant name wifi@c000000 { status = "okay"; qcom,ath11k-calibration-variant = "Cigtech-WF-188"; }; This would create the boarddata identifier for the board-2.bin search * bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188 Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org
2020-10-01ath11k: enable shadow register configuration and accessCarl Huang1-1/+1
To enable shadow register access, host needs to pass shadow register configuration to firmware via qmi message. Host also needs to update ring's HP or TP address to shadow register address. The write operation to shadow register will be forwarded to target register by hardware automatically, and the write operation to shadow register is permitted even when the target is in power save or sleep mode. Update the shadow config whenever power up happens. This feature is controlled by hw parameter supports_shadow_regs which is only enabled for QCA6390. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1601544890-13450-3-git-send-email-kvalo@codeaurora.org
2020-08-17ath11k: fix memory OOB access in qmi_decodeCarl Huang1-0/+8
The decoded_size is wrongly assigned in ath11k_qmi_msg_handlers and it results in out of boundary access in qmi_decode. The correct decoded_size should be calculated from the related ind_msg structure. This issue is exposed with QCA6390 because it needs 11 small memory chunks which are stored in qmi_wlanfw_request_mem_ind_msg_v01 and hence the decoded_size exceeds the wrongly assigend decoded_size. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 Signed-off-by: Carl Huang <cjhuang@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1597389030-13887-9-git-send-email-kvalo@codeaurora.org
2020-08-17ath11k: fill appropriate QMI service instance id for QCA6390Govind Singh1-0/+3
QMI service instance id is used for qmi service lookup, IPQ8074 and QCA6390 uses different instance id for service lookup. Fill appropriate QMI service instance id for respective targets. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1597389030-13887-4-git-send-email-kvalo@codeaurora.org
2020-08-17ath11k: add board file support for PCI devicesGovind Singh1-1/+6
PCI devices like QCA6390 load the board file differently, add support for that and the method is chosen using bus_params variables. Add support to create board name for different targets. This board name is used to parse the board data from board-2.bin for ahb/pci based targets. As struct target_mem_chunk::vaddr was changed from 'u32' to 'u32 *' in ath11k_qmi_assign_target_mem_chunk() vaddr assignments were changed to NULL to avoid a compilation warning. IPQ8074 does not use the vaddr field for anything so that change does not affect functionality. At the moment this only supports board files with BIN type. Support for ELF type, which seems to be more popular on QCA6390 devices, needs to be added later. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1597389030-13887-3-git-send-email-kvalo@codeaurora.org
2020-08-17ath11k: add support for m3 firmwareGovind Singh1-0/+7
PCI devices like QCA6390 have a separate firmware image for the m3 micro-controller. Add support to load the firmware using m3.bin file. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1597389030-13887-2-git-send-email-kvalo@codeaurora.org
2020-06-23ath11k: remove define ATH11K_QMI_DEFAULT_CAL_FILE_NAMEKalle Valo1-1/+0
It's just a duplicate of ATH11K_DEFAULT_CAL_FILE. Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1592316055-24958-13-git-send-email-kvalo@codeaurora.org
2020-06-23ath11k: Add bdf-addr in hw_paramsAnilkumar Kolli1-1/+0
bdf-addr is different for IPQ8074 and IPQ6018 so add it to hw_params. No functional changes. Compile tested only. Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1592316055-24958-6-git-send-email-kvalo@codeaurora.org
2019-11-29ath11k: qmi clean up ce and HTC service config updateAnilkumar Kolli1-2/+2
Copy CE and htc service configs for all pipes. Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-11-25ath11k: driver for Qualcomm IEEE 802.11ax devicesKalle Valo1-0/+445
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k uses mac80211 and supports AP, Station and Mesh modes. Even though ath11k has some similar code as with ath10k (especially the WMI layer) it was concluded to be simpler to have a "clean start" for ath11k code base and not try to share the code with ath10k. This makes maintenance easier and avoids major changes in ath10k, which would have significantly increased the risk of regressions in existing setups. Even though the driver is very similar with ath10k but there are major differences as well. The datapath is completely different. ath11k supports multiple MACs, called "soc" in the firmware interface. And there's only one WMI interface to support. Currently ath11k supports only IEEE 802.11ac mode, but patches for 802.11ax are available and they will be submitted after ath11k is accepted to upstream. The firmware images are available from ath11k-firmware repository but they will be also submitted to linux-firmware: https://github.com/kvalo/ath11k-firmware This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1. The driver has had multiple authors who are listed in alphabetical order below. Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org> Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org> Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org> Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by: kbuild test robot <lkp@intel.com> Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org> Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by: Miles Hu <milehu@codeaurora.org> Signed-off-by: Muna Sinada <msinada@codeaurora.org> Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org> Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com> Signed-off-by: Sriram R <srirrama@codeaurora.org> Signed-off-by: Sven Eckelmann <seckelmann@datto.com> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org> Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-28 23:02:37 +0300