Age | Commit message (Collapse) | Author | Files | Lines |
|
In multi-channel scenarios, the granted channel must be aborted before
suspending. Otherwise, the firmware will be put into a wrong state,
resulting in an association failure after resuming.
With this patch, the granted channel will be aborted before suspending
if necessary.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Before entering suspend, we need to ensure that all MCU command are
completed. In some cases, such as with regd_notifier, there is a
chance that CLC commands, will be executed before suspend.
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
This patch updates the EU country list to ensure the MTCL table
works correctly.
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
config from ACPI
In some case, the MTCL table will exist, but MTDS table will not.
So the SAR will init fail. This patch make MTCL and MTDS can exist
with no dependence.
Fixes: f965333e491e ("mt76: mt7921: introduce ACPI SAR support")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
clc->len is defined as 32 bits in length, so it must also be
operated on with 32 bits, not 16 bits.
Fixes: fa6ad88e023d ("wifi: mt76: mt7921: fix country count limitation for CLC")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312112104.Zkc3QUHr-lkp@intel.com/
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
From commit a304e1b82808 ("[PATCH] Debug shared irqs"), there is a test
to make sure the shared irq handler should be able to handle the unexpected
event after deregistration. For this case, let's apply MT76_REMOVED flag to
indicate the device was removed and do not run into the resource access
anymore.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
From commit a304e1b82808 ("[PATCH] Debug shared irqs"), there is a test
to make sure the shared irq handler should be able to handle the unexpected
event after deregistration. For this case, let's apply MT76_REMOVED flag to
indicate the device was removed and do not run into the resource access
anymore.
BUG: KASAN: use-after-free in mt7921_irq_handler+0xd8/0x100 [mt7921e]
Read of size 8 at addr ffff88824a7d3b78 by task rmmod/11115
CPU: 28 PID: 11115 Comm: rmmod Tainted: G W L 5.17.0 #10
Hardware name: Micro-Star International Co., Ltd. MS-7D73/MPG B650I
EDGE WIFI (MS-7D73), BIOS 1.81 01/05/2024
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x1f/0x190
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
kasan_report.cold+0x7f/0x11b
? mt7921_irq_handler+0xd8/0x100 [mt7921e]
mt7921_irq_handler+0xd8/0x100 [mt7921e]
free_irq+0x627/0xaa0
devm_free_irq+0x94/0xd0
? devm_request_any_context_irq+0x160/0x160
? kobject_put+0x18d/0x4a0
mt7921_pci_remove+0x153/0x190 [mt7921e]
pci_device_remove+0xa2/0x1d0
__device_release_driver+0x346/0x6e0
driver_detach+0x1ef/0x2c0
bus_remove_driver+0xe7/0x2d0
? __check_object_size+0x57/0x310
pci_unregister_driver+0x26/0x250
__do_sys_delete_module+0x307/0x510
? free_module+0x6a0/0x6a0
? fpregs_assert_state_consistent+0x4b/0xb0
? rcu_read_lock_sched_held+0x10/0x70
? syscall_enter_from_user_mode+0x20/0x70
? trace_hardirqs_on+0x1c/0x130
do_syscall_64+0x5c/0x80
? trace_hardirqs_on_prepare+0x72/0x160
? do_syscall_64+0x68/0x80
? trace_hardirqs_on_prepare+0x72/0x160
entry_SYSCALL_64_after_hwframe+0x44/0xae
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/CABXGCsOdvVwdLmSsC8TZ1jF0UOg_F_W3wqLECWX620PUkvNk=A@mail.gmail.com/
Fixes: 9270270d6219 ("wifi: mt76: mt7921: fix PCI DMA hang after reboot")
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The mtcl table provided regulatory information for 5.9/6Ghz channels and
configured by platform venders. So, sometimes vendors may write illegal
values, and therefore it is necessary to check and add corresponding
handling for such cases.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
For the member of 'struct scan_req_tlv', replace data type of
func_mask_ext from 'u8' to '__le32'.
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
In order to recycle skbs in the page_pool "hot" cache in
napi_pp_put_page routine, set napi pointer for MMIO devices in
mt76_create_page_pool().
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Introduce wed.c in order to collect mt76 wed common codebase used by
mt7915 and mt7996 drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add a missing EHT related field to fix the following ethtool warning:
[98179.287352] mt7921e 0003:01:00.0: ei: 74 SSTATS_LEN: 73
Fixes: c74df1c067f2 ("wifi: mt76: mt792x: introduce mt792x-lib module")
Signed-off-by: Gen Xu <genxu6@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Sync the value of HIF_TXD_V2_1 with firmware to let it correctly fill
TXD values for HW path.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The MUAR (multicast unicast address) is an address mapping table that
participates in the process of searching WTBL entries. For mt799x
chipsets, the default muar index of BMC WTBL is 0xe.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
A race condition was observed when accessing mapped registers, so add
locking to protect against concurrent access.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
DMA queue settings of TXS will be initialized by the firmware.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The efuse data starts from the 48th bytes instead of 64th bytes in the
returned event skb.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Since the FW does not support to handle the integrity and validation of
IGTK in GCMP mode, return -EOPNOTSUPP to let it be handled by upper layer.
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Set correct beamformer capabilities for station vif in HE PHY
capability IE.
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
If TLV includes beacon content, its length might not be 4-byte aligned.
Make sure the length is aligned before sending beacon commands to FW.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The EHT MCS map subfield of 20 MHz-Only is not present in the EHT
capability of AP, so STA does not need to parse the subfield.
Moreover, AP should parse the subfield only if STA is 20 MHz-Only, which
can be confirmed by checking supported channel width in HE capability.
Fixes: 92aa2da9fa49 ("wifi: mt76: mt7996: enable EHT support in firmware")
Co-developed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Disable AMSDU for non-data frames to prevent TX token leak issues.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
This patch fixes the following TWT issues:
- Change table_mask to u16 to support up to 16 TWT stations
- Reject TWT flows for duplicated establishment
- Fix possible unaligned pointer
- Remove unsupported TWT_CONTROL_WAKE_DUR_UNIT flag
- The minimum TWT duration supported by mt7996 chipsets is 64. Reply
with TWT_SETUP_CMD_DICTATE if the min_twt_dur is smaller than 64
Fixes: 98686cd21624 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The PPDU TXS does not include the error bit so it cannot use to report
status to mac80211. This patch fixes issue that STA wrongly detects if AP
is still alive.
Fixes: 2569ea5326e2 ("wifi: mt76: mt7996: enable PPDU-TxS to host")
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Allow sensors tool to read radio's temperature, example:
mt7925_phy8-pci-3b00
Adapter: PCI adapter
temp1: +35.0°C
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix the wrong WFDMA settings to improve TX performance.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
There's a race between driver and fw on some tx/rx control registers
when setting ifs, which will cause accidental hw queue pause problems.
Avoid this by setting ifs time with bss_info mcu command.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
A sub-process of Wifi L0.5 reset will make chip common partition
enter low power, and have chance lead to Bluetooth host-to-chip
command timeout, modify the software flow according to the chip's
design to solve the problem.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The header translation config should set to broadcast and unicast
cases correctly, not only unicast case. And also remove the cmds
of wtbl (wlan table) series, because these MCU commands have
already been replaced by other commands in mt7925.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When in suspend mode, WoW (Wake-on-WLAN) fails to wake the system remotely
due to incorrect encryption mode settings. For the new mt7925 chipset, the
old STA_REC_KEY_V2 command will send incorrect parameters to the firmware.
Therefore, STA_REC_KEY_V3 has been introduced as a replacement for it.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add an address of fw region for fw download.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Firmware uses access class index (ACI) for wmm parameters update,
so convert mac80211 queue to ACI in mt7925_conf_tx().
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Apply query command type properly to make the chip send the response back.
Otherwise, we may see the command timeout in driver side.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Hao Zhang <hao.zhang@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Driver should configure basic rate and phy mode for SAP mode.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: rong.yan <rong.yan@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Driver should setting correct phy mode to firmware when in legacy mode.
Fixes: c948b5da6bbe ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Netgear WDNA3100v3 has a chipset that's compatible with the mt76x2u driver
and works without modification with the mainline kernel by writing to sysfs.
Signed-off-by: Dacio Romero <dacioromero@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
dmashdl(DMA scheduler) was disable and may cause packets corruption
without propoer resource handling. Enable this to control resources
between usb-bus/pse/hardware-ac-queue.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Store usb endpoint in mt76_queue structure and rework q2ep routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Create a dedicate queue for psd/mgmt traffic and do not rely on voice
one. This is a preliminary patch to fix mt7921u/mt7925 usb dmasl
configuration.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Fix the following firmware loading error due to a wrong dma register
configuration if wed is disabled.
[ 8.245881] mt7996e_hif 0001:01:00.0: assign IRQ: got 128
[ 8.251308] mt7996e_hif 0001:01:00.0: enabling device (0000 -> 0002)
[ 8.257674] mt7996e_hif 0001:01:00.0: enabling bus mastering
[ 8.263488] mt7996e 0000:01:00.0: assign IRQ: got 126
[ 8.268537] mt7996e 0000:01:00.0: enabling device (0000 -> 0002)
[ 8.274551] mt7996e 0000:01:00.0: enabling bus mastering
[ 28.648773] mt7996e 0000:01:00.0: Message 00000010 (seq 1) timeout
[ 28.654959] mt7996e 0000:01:00.0: Failed to get patch semaphore
[ 29.661033] mt7996e: probe of 0000:01:00.0 failed with error -11
Suggested-by: Sujuan Chen" <sujuan.chen@mediatek.com>
Fixes: 4920a3a1285f ("wifi: mt76: mt7996: set DMA mask to 36 bits for boards with more than 4GB of RAM")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Add support for a newer ADIE version
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Sicne the mapping is global, mapped register access needs to be protected
against concurrent access, otherwise a race condition might cause the reads
or writes to go towards the wrong register
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Do not clear the interrupt mask register on MT7915, since that prevents
MCU_CMD interrupts from being reported, thus causing timeouts during the
reset sequence. Defer stopping WED until tx/rx processing activity has
stopped.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The PPDU TxS does not include the error bit so it cannot use to report
status to mac80211.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
When using fixed rate, HW uses txd DW9 to store tx arrivial time if VTA
is set. It would overwrite the msdu_id in txd and lead to token pending
if amsdu is enable.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
This reverts commit fcf690b0b47494df51d214db5c5a714a400b0257.
When using a wilc1000 chip over a spi bus, users can optionally define a
reset gpio and a chip enable gpio. The reset line of wilc1000 is active
low, so to hold the chip in reset, a low (physical) value must be applied.
The corresponding device tree binding documentation was introduced by
commit f31ee3c0a555 ("wilc1000: Document enable-gpios and reset-gpios
properties") and correctly indicates that the reset line is an active-low
signal. The corresponding driver part, brought by commit ec031ac4792c
("wilc1000: Add reset/enable GPIO support to SPI driver") was applying the
correct logic. But commit fcf690b0b474 ("wifi: wilc1000: use correct
sequence of RESET for chip Power-UP/Down") eventually flipped this logic
and started misusing the gpiod APIs, applying an inverted logic when
powering up/down the chip (for example, setting the reset line to a logic
"1" during power up, which in fact asserts the reset line when device tree
describes the reset line as GPIO_ACTIVE_LOW). As a consequence, any
platform currently using the driver in SPI mode must use a faulty reset
line description in device tree, or else chip will be maintained in reset
and will not even allow to bring up the chip.
Fix reset line usage by inverting back the gpiod APIs usage, setting the
reset line to the logic value "0" when powering the chip, and the logic
value "1" when powering off the chip.
Fixes: fcf690b0b474 ("wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240217-wilc_1000_reset_line-v2-1-b216f433d7d5@bootlin.com
|
|
The ACEPC W5 Pro HDMI stick contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
"brcmfmac43455-sdio.$(DEFAULT_STRING)-$(DEFAULT_STRING).txt" as nvram file
which is both too generic and messy with the $ symbols in the name.
The ACEPC W5 Pro uses the same Ampak AP6255 module as the ACEPC T8
and the nvram for the T8 is already in linux-firmware, so point the new
DMI nvram filename quirk to the T8 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240216213649.251718-1-hdegoede@redhat.com
|
|
Map USB endpoints to hardware and AC queues according to number of USB
endpoints. However, original only give a warning for unexpected cases but
initial values are not given. Then, smatch warns:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:642
_rtl92cu_init_chipn_two_out_ep_priority() error: uninitialized symbol 'valuelow'.
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:644
_rtl92cu_init_chipn_two_out_ep_priority() error: uninitialized symbol 'valuehi'.
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:649
_rtl92cu_init_chipn_two_out_ep_priority() error: uninitialized symbol 'valuehi'.
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:650
_rtl92cu_init_chipn_two_out_ep_priority() error: uninitialized symbol 'valuelow'.
The regular selection is high and low queues, so move default (unexpected)
case along with that.
Compile tested only.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240216033949.34765-1-pkshih@realtek.com
|
|
The 'vif' is from tx_info of SKB, and other codes check 'vif' before using,
which raises smatch warnings:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:5656 rtl8xxxu_tx()
warn: variable dereferenced before check 'vif' (see line 5553)
Compile tested only.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240216033923.34683-1-pkshih@realtek.com
|
|
rtl8192cu is checking rtl_mac.tids when deciding if it should enable
aggregation. This is wrong because rtl_mac.tids is not initialised
anywhere. Check rtl_sta_info.tids instead, which is initialised.
Also, when enabling aggregation also enable RTS. The vendor driver does
this, my router does this. It seems like the thing to do.
Also also, it seems right to set the AMPDU density only when enabling
aggregation.
Also also also, delete the unused member rtl_mac.tids and the unused
macros RTL_AGG_ON and RTL_AGG_OFF.
Naturally, with working AMPDU the download/upload speeds are better.
Before: 59/32 Mbps.
After: 68/46 Mbps.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/4e936334-5f81-403f-a495-0628ebfb6903@gmail.com
|