Age | Commit message (Collapse) | Author | Files | Lines |
|
The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older. This
will cause the VF driver to fail during probe:
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
bnxt_en 0000:00:03.0: Unable to initialize mac address.
bnxt_en: probe of 0000:00:03.0 failed with error -99
We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.
Fixes: 707e7e966026 ("bnxt_en: Always forward VF MAC address to the PF.")
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Siwei Liu <loseweigh@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The operation ~(p100_inb(VG_LAN_CFG_1) & HP100_LINK_UP) returns a value
that is always non-zero and hence the wait for the link to drop always
terminates prematurely. Fix this by using a logical not operator instead
of a bitwise complement. This issue has been in the driver since
pre-2.6.12-rc2.
Detected by CoverityScan, CID#114157 ("Logical vs. bitwise operator")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a new configuration for the sama5d3-macb new compatibility string.
This configuration disables scatter-gather because we experienced lock down
of the macb interface of this particular SoC under very high load.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Net drivers using phylink shouldn't mess with the link carrier
themselves and should let phylink manage it. The mvpp2 driver wasn't
following this best practice as the mac_config() function made calls to
change the link carrier state. This led to wrongly reported carrier link
state which then triggered other issues. This patch fixes this
behaviour.
But the PPv2 driver relied on this misbehaviour in two cases: for fixed
links and when not using phylink (ACPI mode). The later was fixed by
adding an explicit call to link_up(), which when the ACPI mode will use
phylink should be removed.
The fixed link case was relying on the mac_config() function to set the
link up, as we found an issue in phylink_start() which assumes the
carrier is off. If not, the link_up() function is never called. To fix
this, a call to netif_carrier_off() is added just before phylink_start()
so that we do not introduce a regression in the driver.
Fixes: 4bb043262878 ("net: mvpp2: phylink support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pppoe_rcv() needs to look back at the Ethernet header in order to
lookup the PPPoE session. Therefore we need to ensure that the mac
header is big enough to contain an Ethernet header. Otherwise
eth_hdr(skb)->h_source might access invalid data.
==================================================================
BUG: KMSAN: uninit-value in __get_item drivers/net/ppp/pppoe.c:172 [inline]
BUG: KMSAN: uninit-value in get_item drivers/net/ppp/pppoe.c:236 [inline]
BUG: KMSAN: uninit-value in pppoe_rcv+0xcef/0x10e0 drivers/net/ppp/pppoe.c:450
CPU: 0 PID: 4543 Comm: syz-executor355 Not tainted 4.16.0+ #87
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:53
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
__get_item drivers/net/ppp/pppoe.c:172 [inline]
get_item drivers/net/ppp/pppoe.c:236 [inline]
pppoe_rcv+0xcef/0x10e0 drivers/net/ppp/pppoe.c:450
__netif_receive_skb_core+0x47df/0x4a90 net/core/dev.c:4562
__netif_receive_skb net/core/dev.c:4627 [inline]
netif_receive_skb_internal+0x49d/0x630 net/core/dev.c:4701
netif_receive_skb+0x230/0x240 net/core/dev.c:4725
tun_rx_batched drivers/net/tun.c:1555 [inline]
tun_get_user+0x740f/0x7c60 drivers/net/tun.c:1962
tun_chr_write_iter+0x1d4/0x330 drivers/net/tun.c:1990
call_write_iter include/linux/fs.h:1782 [inline]
new_sync_write fs/read_write.c:469 [inline]
__vfs_write+0x7fb/0x9f0 fs/read_write.c:482
vfs_write+0x463/0x8d0 fs/read_write.c:544
SYSC_write+0x172/0x360 fs/read_write.c:589
SyS_write+0x55/0x80 fs/read_write.c:581
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x4447c9
RSP: 002b:00007fff64c8fc28 EFLAGS: 00000297 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00000000004447c9
RDX: 000000000000fd87 RSI: 0000000020000600 RDI: 0000000000000004
RBP: 00000000006cf018 R08: 00007fff64c8fda8 R09: 00007fff00006bda
R10: 0000000000005fe7 R11: 0000000000000297 R12: 00000000004020d0
R13: 0000000000402160 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
slab_post_alloc_hook mm/slab.h:445 [inline]
slab_alloc_node mm/slub.c:2737 [inline]
__kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:984 [inline]
alloc_skb_with_frags+0x1d4/0xb20 net/core/skbuff.c:5234
sock_alloc_send_pskb+0xb56/0x1190 net/core/sock.c:2085
tun_alloc_skb drivers/net/tun.c:1532 [inline]
tun_get_user+0x2242/0x7c60 drivers/net/tun.c:1829
tun_chr_write_iter+0x1d4/0x330 drivers/net/tun.c:1990
call_write_iter include/linux/fs.h:1782 [inline]
new_sync_write fs/read_write.c:469 [inline]
__vfs_write+0x7fb/0x9f0 fs/read_write.c:482
vfs_write+0x463/0x8d0 fs/read_write.c:544
SYSC_write+0x172/0x360 fs/read_write.c:589
SyS_write+0x55/0x80 fs/read_write.c:581
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
==================================================================
Fixes: 224cf5ad14c0 ("ppp: Move the PPP drivers")
Reported-by: syzbot+f5f6080811c849739212@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch mades TI_DAVINCI_CPDMA select GENERIC_ALLOCATOR.
without that, the following sparc64 build failure happen
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
(.text+0x278): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit':
(.text+0x340): undefined reference to `gen_pool_alloc'
(.text+0x5c4): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x64c): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.6':
davinci_cpdma.c:(.text+0x17ac): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x17b8): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x1824): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x1830): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
(.text+0x19f8): undefined reference to `devm_gen_pool_create'
(.text+0x1a90): undefined reference to `gen_pool_add_virt'
Makefile:1011: recipe for target 'vmlinux' failed
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GRO expects skbs not to be owned by sockets, but when XDP is enabled veth
passed skbs owned by sockets. It caused corrupted sk_wmem_alloc.
Paolo Abeni reported the following splat:
[ 362.098904] refcount_t overflow at skb_set_owner_w+0x5e/0xa0 in iperf3[1644], uid/euid: 0/0
[ 362.108239] WARNING: CPU: 0 PID: 1644 at kernel/panic.c:648 refcount_error_report+0xa0/0xa4
[ 362.117547] Modules linked in: tcp_diag inet_diag veth intel_rapl sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel intel_cstate intel_uncore intel_rapl_perf ipmi_ssif iTCO_wdt sg ipmi_si iTCO_vendor_support ipmi_devintf mxm_wmi ipmi_msghandler pcspkr dcdbas mei_me wmi mei lpc_ich acpi_power_meter pcc_cpufreq xfs libcrc32c sd_mod mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ixgbe igb ttm ahci mdio libahci ptp crc32c_intel drm pps_core libata i2c_algo_bit dca dm_mirror dm_region_hash dm_log dm_mod
[ 362.176622] CPU: 0 PID: 1644 Comm: iperf3 Not tainted 4.19.0-rc2.vanilla+ #2025
[ 362.184777] Hardware name: Dell Inc. PowerEdge R730/072T6D, BIOS 2.1.7 06/16/2016
[ 362.193124] RIP: 0010:refcount_error_report+0xa0/0xa4
[ 362.198758] Code: 08 00 00 48 8b 95 80 00 00 00 49 8d 8c 24 80 0a 00 00 41 89 c1 44 89 2c 24 48 89 de 48 c7 c7 18 4d e7 9d 31 c0 e8 30 fa ff ff <0f> 0b eb 88 0f 1f 44 00 00 55 48 89 e5 41 56 41 55 41 54 49 89 fc
[ 362.219711] RSP: 0018:ffff9ee6ff603c20 EFLAGS: 00010282
[ 362.225538] RAX: 0000000000000000 RBX: ffffffff9de83e10 RCX: 0000000000000000
[ 362.233497] RDX: 0000000000000001 RSI: ffff9ee6ff6167d8 RDI: ffff9ee6ff6167d8
[ 362.241457] RBP: ffff9ee6ff603d78 R08: 0000000000000490 R09: 0000000000000004
[ 362.249416] R10: 0000000000000000 R11: ffff9ee6ff603990 R12: ffff9ee664b94500
[ 362.257377] R13: 0000000000000000 R14: 0000000000000004 R15: ffffffff9de615f9
[ 362.265337] FS: 00007f1d22d28740(0000) GS:ffff9ee6ff600000(0000) knlGS:0000000000000000
[ 362.274363] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 362.280773] CR2: 00007f1d222f35d0 CR3: 0000001fddfec003 CR4: 00000000001606f0
[ 362.288733] Call Trace:
[ 362.291459] <IRQ>
[ 362.293702] ex_handler_refcount+0x4e/0x80
[ 362.298269] fixup_exception+0x35/0x40
[ 362.302451] do_trap+0x109/0x150
[ 362.306048] do_error_trap+0xd5/0x130
[ 362.315766] invalid_op+0x14/0x20
[ 362.319460] RIP: 0010:skb_set_owner_w+0x5e/0xa0
[ 362.324512] Code: ef ff ff 74 49 48 c7 43 60 20 7b 4a 9d 8b 85 f4 01 00 00 85 c0 75 16 8b 83 e0 00 00 00 f0 01 85 44 01 00 00 0f 88 d8 23 16 00 <5b> 5d c3 80 8b 91 00 00 00 01 8b 85 f4 01 00 00 89 83 a4 00 00 00
[ 362.345465] RSP: 0018:ffff9ee6ff603e20 EFLAGS: 00010a86
[ 362.351291] RAX: 0000000000001100 RBX: ffff9ee65deec700 RCX: ffff9ee65e829244
[ 362.359250] RDX: 0000000000000100 RSI: ffff9ee65e829100 RDI: ffff9ee65deec700
[ 362.367210] RBP: ffff9ee65e829100 R08: 000000000002a380 R09: 0000000000000000
[ 362.375169] R10: 0000000000000002 R11: fffff1a4bf77bb00 R12: ffffc0754661d000
[ 362.383130] R13: ffff9ee65deec200 R14: ffff9ee65f597000 R15: 00000000000000aa
[ 362.391092] veth_xdp_rcv+0x4e4/0x890 [veth]
[ 362.399357] veth_poll+0x4d/0x17a [veth]
[ 362.403731] net_rx_action+0x2af/0x3f0
[ 362.407912] __do_softirq+0xdd/0x29e
[ 362.411897] do_softirq_own_stack+0x2a/0x40
[ 362.416561] </IRQ>
[ 362.418899] do_softirq+0x4b/0x70
[ 362.422594] __local_bh_enable_ip+0x50/0x60
[ 362.427258] ip_finish_output2+0x16a/0x390
[ 362.431824] ip_output+0x71/0xe0
[ 362.440670] __tcp_transmit_skb+0x583/0xab0
[ 362.445333] tcp_write_xmit+0x247/0xfb0
[ 362.449609] __tcp_push_pending_frames+0x2d/0xd0
[ 362.454760] tcp_sendmsg_locked+0x857/0xd30
[ 362.459424] tcp_sendmsg+0x27/0x40
[ 362.463216] sock_sendmsg+0x36/0x50
[ 362.467104] sock_write_iter+0x87/0x100
[ 362.471382] __vfs_write+0x112/0x1a0
[ 362.475369] vfs_write+0xad/0x1a0
[ 362.479062] ksys_write+0x52/0xc0
[ 362.482759] do_syscall_64+0x5b/0x180
[ 362.486841] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 362.492473] RIP: 0033:0x7f1d22293238
[ 362.496458] Code: 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 c5 54 2d 00 8b 00 85 c0 75 17 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 49 89 d4 55
[ 362.517409] RSP: 002b:00007ffebaef8008 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 362.525855] RAX: ffffffffffffffda RBX: 0000000000002800 RCX: 00007f1d22293238
[ 362.533816] RDX: 0000000000002800 RSI: 00007f1d22d36000 RDI: 0000000000000005
[ 362.541775] RBP: 00007f1d22d36000 R08: 00000002db777a30 R09: 0000562b70712b20
[ 362.549734] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000005
[ 362.557693] R13: 0000000000002800 R14: 00007ffebaef8060 R15: 0000562b70712260
In order to avoid this, orphan the skb before entering GRO.
Fixes: 948d4f214fde ("veth: Add driver XDP")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or
128 unicast filter entries. (Table 7-8 MAC Address Registers from
databook) Fix dwmac1000_validate_ucast_entries() to accept values
between 1 and 32 in addition.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fields ->dev and ->next of struct ipddp_route may be copied to
userspace on the SIOCFINDIPDDPRT ioctl. This is only accessible
to CAP_NET_ADMIN though. Let's manually copy the relevant fields
instead of using memcpy().
BugLink: http://blog.infosectcbr.com.au/2018/09/linux-kernel-infoleaks.html
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When netvsc device is removed it can call reschedule in RCU context.
This happens because canceling the subchannel setup work could (in theory)
cause a reschedule when manipulating the timer.
To reproduce, run with lockdep enabled kernel and unbind
a network device from hv_netvsc (via sysfs).
[ 160.682011] WARNING: suspicious RCU usage
[ 160.707466] 4.19.0-rc3-uio+ #2 Not tainted
[ 160.709937] -----------------------------
[ 160.712352] ./include/linux/rcupdate.h:302 Illegal context switch in RCU read-side critical section!
[ 160.723691]
[ 160.723691] other info that might help us debug this:
[ 160.723691]
[ 160.730955]
[ 160.730955] rcu_scheduler_active = 2, debug_locks = 1
[ 160.762813] 5 locks held by rebind-eth.sh/1812:
[ 160.766851] #0: 000000008befa37a (sb_writers#6){.+.+}, at: vfs_write+0x184/0x1b0
[ 160.773416] #1: 00000000b097f236 (&of->mutex){+.+.}, at: kernfs_fop_write+0xe2/0x1a0
[ 160.783766] #2: 0000000041ee6889 (kn->count#3){++++}, at: kernfs_fop_write+0xeb/0x1a0
[ 160.787465] #3: 0000000056d92a74 (&dev->mutex){....}, at: device_release_driver_internal+0x39/0x250
[ 160.816987] #4: 0000000030f6031e (rcu_read_lock){....}, at: netvsc_remove+0x1e/0x250 [hv_netvsc]
[ 160.828629]
[ 160.828629] stack backtrace:
[ 160.831966] CPU: 1 PID: 1812 Comm: rebind-eth.sh Not tainted 4.19.0-rc3-uio+ #2
[ 160.832952] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v1.0 11/26/2012
[ 160.832952] Call Trace:
[ 160.832952] dump_stack+0x85/0xcb
[ 160.832952] ___might_sleep+0x1a3/0x240
[ 160.832952] __flush_work+0x57/0x2e0
[ 160.832952] ? __mutex_lock+0x83/0x990
[ 160.832952] ? __kernfs_remove+0x24f/0x2e0
[ 160.832952] ? __kernfs_remove+0x1b2/0x2e0
[ 160.832952] ? mark_held_locks+0x50/0x80
[ 160.832952] ? get_work_pool+0x90/0x90
[ 160.832952] __cancel_work_timer+0x13c/0x1e0
[ 160.832952] ? netvsc_remove+0x1e/0x250 [hv_netvsc]
[ 160.832952] ? __lock_is_held+0x55/0x90
[ 160.832952] netvsc_remove+0x9a/0x250 [hv_netvsc]
[ 160.832952] vmbus_remove+0x26/0x30
[ 160.832952] device_release_driver_internal+0x18a/0x250
[ 160.832952] unbind_store+0xb4/0x180
[ 160.832952] kernfs_fop_write+0x113/0x1a0
[ 160.832952] __vfs_write+0x36/0x1a0
[ 160.832952] ? rcu_read_lock_sched_held+0x6b/0x80
[ 160.832952] ? rcu_sync_lockdep_assert+0x2e/0x60
[ 160.832952] ? __sb_start_write+0x141/0x1a0
[ 160.832952] ? vfs_write+0x184/0x1b0
[ 160.832952] vfs_write+0xbe/0x1b0
[ 160.832952] ksys_write+0x55/0xc0
[ 160.832952] do_syscall_64+0x60/0x1b0
[ 160.832952] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 160.832952] RIP: 0033:0x7fe48f4c8154
Resolve this by getting RTNL earlier. This is safe because the subchannel
work queue does trylock on RTNL and will detect the race.
Fixes: 7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 57f230ab04d291 ("xen/netfront: raise max number of slots in
xennet_get_responses()") raised the max number of allowed slots by one.
This seems to be problematic in some configurations with netback using
a larger MAX_SKB_FRAGS value (e.g. old Linux kernel with MAX_SKB_FRAGS
defined as 18 instead of nowadays 17).
Instead of BUG_ON() in this case just fall back to retransmission.
Fixes: 57f230ab04d291 ("xen/netfront: raise max number of slots in xennet_get_responses()")
Cc: stable@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a bug where ipv6 tunnels would report that it is
getting offloaded to hardware but would actually be rejected
by hardware.
Fixes: b27d6a95a70d ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously we only checked if the vlan id field is present when trying
to match a vlan tag. The vlan id and vlan pcp field should be treated
independently.
Fixes: 5571e8c9f241 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After system suspend, sometimes the r8169 doesn't work when ethernet
cable gets pluggued.
This issue happens because rtl_reset_work() doesn't get called from
rtl8169_runtime_resume(), after system suspend.
In rtl_task(), RTL_FLAG_TASK_* only gets cleared if this condition is
met:
if (!netif_running(dev) ||
!test_bit(RTL_FLAG_TASK_ENABLED, tp->wk.flags))
...
If RTL_FLAG_TASK_ENABLED was cleared during system suspend while
RTL_FLAG_TASK_RESET_PENDING was set, the next rtl_schedule_task() won't
schedule task as the flag is still there.
So in addition to clearing RTL_FLAG_TASK_ENABLED, also clears other
flags.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dma_zalloc_coherent() now crashes if no dev pointer is given.
Add a dev pointer to the ltq_dma_channel structure and fill it in the
driver using it.
This fixes a bug introduced in kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the incorrect WR_HDR field which can cause a misinterpretation
of ABORT CPL by ULDs, such as iw_cxgb4.
Fixes: a3cdaa69e4ae ("cxgb4: Adds CPL support for Shared Receive Queues")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Quectel EP06 (and EM06/EG06) supports dynamic configuration of USB
interfaces, without the device changing VID/PID or configuration number.
When the configuration is updated and interfaces are added/removed, the
interface numbers change. This means that the current code for matching
EP06 does not work.
This patch removes the current EP06 interface number match, and replaces
it with a match on class, subclass and protocol. Unfortunately, matching
on those three alone is not enough, as the diag interface exports the
same values as QMI. The other serial interfaces + adb export different
values and do not match.
The diag interface only has two endpoints, while the QMI interface has
three. I have therefore added a check for number of interfaces, and we
ignore the interface if the number of endpoints equals two.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added memory barriers where they were missing to support multiple
architectures, and removed redundant ones.
As part of removing the redundant memory barriers and improving
performance, we moved to more relaxed versions of memory barriers,
as well as to the more relaxed version of writel - writel_relaxed,
while maintaining correctness.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add READ_ONCE calls where necessary (for example when iterating
over a memory field that gets updated by the hardware).
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
acquire the rtnl_lock during device destruction to avoid
using partially destroyed device.
ena_remove() shares almost the same logic as ena_destroy_device(),
so use ena_destroy_device() and avoid duplications.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ena_destroy_device() can potentially be called twice.
To avoid this, check that the device is running and
only then proceed destroying it.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ena_destroy_device() is called from ena_suspend(), the device is
still reachable from the driver. Therefore, the driver can send a command
to the device to free all resources.
However, in all other cases of calling ena_destroy_device(), the device is
potentially in an error state and unreachable from the driver. In these
cases the driver must not send commands to the device.
The current implementation does not request resource freeing from the
device even when possible. We add the graceful parameter to
ena_destroy_device() to enable resource freeing when possible, and
use it in ena_suspend().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The buffer length field in the ena rx descriptor is 16 bit, and the
current driver passes a full page in each ena rx descriptor.
When PAGE_SIZE equals 64kB or more, the buffer length field becomes
zero.
To solve this issue, limit the ena Rx descriptor to use 16kB even
when allocating 64kB kernel pages. This change would not impact ena
device functionality, as 16kB is still larger than maximum MTU.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Starting with driver version 1.5.0, in case of a surprise device
unplug, there is a race caused by invoking ena_destroy_device()
from two different places. As a result, the readless register might
be accessed after it was destroyed.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 822fb18a82aba ("xen-netfront: wait xenbus state change when load
module manually") added a new wait queue to wait on for a state change
when the module is loaded manually. Unfortunately there is no wakeup
anywhere to stop that waiting.
Instead of introducing a new wait queue rename the existing
module_unload_q to module_wq and use it for both purposes (loading and
unloading).
As any state change of the backend might be intended to stop waiting
do the wake_up_all() in any case when netback_changed() is called.
Fixes: 822fb18a82aba ("xen-netfront: wait xenbus state change when load module manually")
Cc: <stable@vger.kernel.org> #4.18
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3559d81e76bf ("r8169: simplify rtl_hw_start_8169") changed order of
two register writes:
1) Caused RxConfig to be written before TX / RX is enabled,
2) Caused TxConfig to be written before TX / RX is enabled.
At least on XIDs 10000000 ("RTL8169sb/8110sb") and
18000000 ("RTL8169sc/8110sc") such writes are ignored by the chip, leaving
values in these registers intact.
Change 1) was reverted by
commit 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices"),
however change 2) wasn't.
In practice, this caused TxConfig's "InterFrameGap time" and "Max DMA Burst
Size per Tx DMA Burst" bits to be zero dramatically reducing TX performance
(in my tests it dropped from around 500Mbps to around 50Mbps).
This patch fixes the issue by moving TxConfig register write a bit later in
the code so it happens after TX / RX is already enabled.
Fixes: 05212ba8132b42 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a false positive report due to incorrect nested lock
annotations as we lock multiple fgs with the same subclass.
Instead of locking all fgs only lock the one being used as was
done before.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Copy and paste bug was introduced in the offending patch.
We need to write udp source port value into the headers value and not
headers criteria "mask".
Fixes: 142644f8a1f8 ("net/mlx5e: Ethtool steering flow parsing refactoring")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, mlx5_attach_interface does not check for error
after calling intf->attach or intf->add. When these two calls
fails, the client is not initialized and will cause issues such as
kernel panic on invalid address in the teardown path (mlx5_detach_interface)
Fixes: 737a234bb638 ("net/mlx5: Introduce attach/detach to interface API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The PCI BDF is not unique. PCI domain must also be considered when
searching for the next physical device during lag setup. Example below:
mlx5_core 0000:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0000:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If building match list fg fails and we never jumped to
search_again_locked label then the function returned without
unlocking the read lock.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The memory allocated for the slow path table flow group input structure
was not freed upon successful return, fix that.
Fixes: 1967ce6ea5c8 ("net/mlx5: E-Switch, Refactor fast path FDB table creation in switchdev mode")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.
u16 is sufficient to represent this.
Fixes: d7037ad73daa ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.
u16 is sufficient to represent this.
Fixes: 388ca8be0037 ("IB/mlx5: Implement fragmented completion queue (CQ)")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When initializing the device (procedure init_one), the driver
calls mlx5_pci_init to perform pci initialization. As part of this
initialization, mlx5_pci_init creates a debugfs directory.
If this creation fails, init_one aborts, returning failure to
the caller (which is the probe method caller).
The main reason for such a failure to occur is if the debugfs
directory already exists. This can happen if the last time
mlx5_pci_close was called, debugfs_remove (silently) failed due
to the debugfs directory not being empty.
Guarantee that such a debugfs_remove failure will not occur by
instead calling debugfs_remove_recursive in procedure mlx5_pci_close.
Fixes: 59211bd3b632 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
With performance optimization the spi transfer and messages of basic
register operations like qcaspi_read_register moved into the private
driver structure. But they weren't protected against mutual access
(e.g. between driver kthread and ethtool). So dumping the QCA7000
registers via ethtool during network traffic could make spi_sync
hang forever, because the completion in spi_message is overwritten.
So revert the optimization completely.
Fixes: 291ab06ecf676 ("net: qualcomm: new Ethernet over SPI driver for QCA700")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DMA allocated memory is lost in be_cmd_get_profile_config() when we
call it with non-NULL port_res parameter.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MC-aware mode was recently enabled by mlxsw on Spectrum switches in
commit 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw
ports"). Unfortunately, testing has shown that the fix is incomplete and
in the presented form actually makes the problem even worse, because any
amount of MC traffic causes UC disruption.
The reason for this is that currently, mlxsw configures the MC-specific
TCs (8..15) to map to pool 0. It also configures a maximum buffer size
of 0, but for MC traffic that maximum is disregarded and not part of the
quota. Therefore MC traffic is always admitted to the egress buffer.
Fix the configuration by directing the MC TCs into pool 15, which is
dedicated to MC traffic and recognized as such by the silicon.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all SFPs implement the registers containing sensor limits and
alarms. Luckily, there is a bit indicating if they are implemented or
not. Add checking for this bit, when deciding if the hwmon attributes
should be visible.
Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Correct the formula for calculating the RQ page remainder,
which should be in byte granularity. The result will be
non-zero only for RQs smaller than PAGE_SIZE, as an RQ size
is a power of 2.
Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the
SQ offset in strides granularity.
Fixes: d7037ad73daa ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea506 ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unused bnxt_subtract_ulp_resources(). Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0. This will properly setup the
init sequence to initialize the default rings again. We also need
to signal the RDMA driver to stop and clear its interrupts. We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.
Fixes: 25e1acd6b92b ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__emac_calc_base_mr1 was used instead of __emac4_calc_base_mr1
by copy-paste mistake for emac4syn.
Fixes: 45d6e545505fd32edb812f085be7de45b6a5c0af ("net/ibm/emac: add 8192 rx/tx fifo size")
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This card identifies itself as:
Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06)
Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468]
Adding a new entry to rtl8169_pci_tbl makes the card work.
Link: http://launchpad.net/bugs/1788730
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel module may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task
To fix this bug, usleep_range() is replaced with udelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw-phy-sel device is not a child of the cpsw interconnect target
module. It lives in the system control module.
Let's fix this issue by trying to use cpsw-phy-sel phandle first if it
exists and if not fall back to current usage of trying to find the
cpsw-phy-sel child. That way the phy sel driver can be a child of the
system control module where it belongs in the device tree.
Without this fix, we cannot have a proper interconnect target module
hierarchy in device tree for things like genpd.
Note that deferred probe is mostly not supported by cpsw and this patch
does not attempt to fix that. In case deferred probe support is needed,
this could be added to cpsw_slave_open() and phy_connect() so they start
handling and returning errors.
For documenting it, looks like the cpsw-phy-sel is used for all cpsw device
tree nodes. It's missing the related binding documentation, so let's also
update the binding documentation accordingly.
Cc: devicetree@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|