Age | Commit message (Collapse) | Author | Files | Lines |
|
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The System EID (SEID) is an internal EID that is used by the SMCv2
software stack that has a predefined and constant value representing
the s390 physical machine that the OS is executing on. So it should
be managed by SMC stack instead of ISM driver and be consistent for
all ISMv2 device (including virtual ISM devices) on s390 architecture.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-and-tested-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to virtual ISM support feature defined by SMCv2.1, GIDs of
virtual ISM device are UUIDs defined by RFC4122, which are 128-bits
long. So some adaptation work is required. And note that the GIDs of
existing platform firmware ISM devices still remain 64-bits long.
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit a72178cfe855 ("net/smc: Fix dependency of SMC on ISM")
you can build the ism code without selecting the SMC network protocol.
That leaves some ism functions be reported as unused. Move these
functions under the conditional compile with CONFIG_SMC.
Also codify the suggestion to also configure the SMC protocol in ism's
Kconfig - but with an "imply" rather than a "select" as SMC depends on
other config options and allow for a deliberate decision not to build
SMC. Also, mention that in ISM's help.
Fixes: a72178cfe855 ("net/smc: Fix dependency of SMC on ISM")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/netdev/afd142a2-1fa0-46b9-8b2d-7652d41d3ab8@infradead.org/
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace 'weed' with 'we' in the comment.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect new_entry->dbf_name to be NUL-terminated based on its use with
strcmp():
| if (strcmp(entry->dbf_name, name) == 0) {
Moreover, NUL-padding is not required as new_entry is kzalloc'd just
before this assignment:
| new_entry = kzalloc(sizeof(struct qeth_dbf_entry), GFP_KERNEL);
... rendering any future NUL-byte assignments (like the ones strncpy()
does) redundant.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Tested-by: Thorsten Winkler <twinkler@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231023-strncpy-drivers-s390-net-qeth_core_main-c-v1-1-e7ce65454446@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect chid to be NUL-terminated based on its use with format
strings:
CTCM_DBF_TEXT_(SETUP, CTC_DBF_INFO, "%s(%s) %s", CTCM_FUNTAIL,
chid, ok ? "OK" : "failed");
Moreover, NUL-padding is not required as it is _only_ used in this one
instance with a format string.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
We can also drop the +1 from chid's declaration as we no longer need to
be cautious about leaving a spot for a NUL-byte. Let's use the more
idiomatic strscpy usage of (dest, src, sizeof(dest)) as this more
closely ties the destination buffer to the length.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Tested-by: Thorsten Winkler <twinkler@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231023-strncpy-drivers-s390-net-ctcm_main-c-v1-1-265db6e78165@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the SMC protocol is built into the kernel proper while ISM is
configured to be built as module, linking the kernel fails due to
unresolved dependencies out of net/smc/smc_ism.o to
ism_get_smcd_ops, ism_register_client, and ism_unregister_client
as reported via the linux-next test automation (see link).
This however is a bug introduced a while ago.
Correct the dependency list in ISM's and SMC's Kconfig to reflect the
dependencies that are actually inverted. With this you cannot build a
kernel with CONFIG_SMC=y and CONFIG_ISM=m. Either ISM needs to be 'y',
too - or a 'n'. That way, SMC can still be configured on non-s390
architectures that do not have (nor need) an ISM driver.
Fixes: 89e7d2ba61b7 ("net/ism: Add new API for client registration")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/linux-next/d53b5b50-d894-4df8-8969-fd39e63440ae@infradead.org/
Co-developed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20231006125847.1517840-1-gbayer@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/dsa/port.c
9945c1fb03a3 ("net: dsa: fix older DSA drivers using phylink")
a88dd7538461 ("net: dsa: remove legacy_pre_march2020 detection")
https://lore.kernel.org/all/20230731102254.2c9868ca@canb.auug.org.au/
net/xdp/xsk.c
3c5b4d69c358 ("net: annotate data-races around sk->sk_mark")
b7f72a30e9ac ("xsk: introduce wrappers and helpers for supporting multi-buffer in Tx path")
https://lore.kernel.org/all/20230731102631.39988412@canb.auug.org.au/
drivers/net/ethernet/broadcom/bnxt/bnxt.c
37b61cda9c16 ("bnxt: don't handle XDP in netpoll")
2b56b3d99241 ("eth: bnxt: handle invalid Tx completions more gracefully")
https://lore.kernel.org/all/20230801101708.1dc7faac@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_fs.c
62da08331f1a ("net/mlx5e: Set proper IPsec source port in L4 selector")
fbd517549c32 ("net/mlx5e: Add function to get IPsec offload namespace")
drivers/net/ethernet/sfc/selftest.c
55c1528f9b97 ("sfc: fix field-spanning memcpy in selftest")
ae9d445cd41f ("sfc: Miscellaneous comment removals")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dev_close() and dev_open() are issued to change the interface state to DOWN
or UP (dev->flags IFF_UP). When the netdev is set DOWN it loses e.g its
Ipv6 addresses and routes. We don't want this in cases of device recovery
(triggered by hardware or software) or when the qeth device is set
offline.
Setting a qeth device offline or online and device recovery actions call
netif_device_detach() and/or netif_device_attach(). That will reset or
set the LOWER_UP indication i.e. change the dev->state Bit
__LINK_STATE_PRESENT. That is enough to e.g. cause bond failovers, and
still preserves the interface settings that are handled by the network
stack.
Don't call dev_open() nor dev_close() from the qeth device driver. Let the
network stack handle this.
Fixes: d4560150cb47 ("s390/qeth: call dev_close() during recovery")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last s390 machine that supported FDDI was z900 ('7th generation',
released in 2000). The oldest machine generation currently supported by
the Linux kernel is MARCH_Z10 (released 2008). If there is still a usecase
for connecting a Linux on s390 instance to a LAN Channel Station (LCS), it
can only do so via Ethernet.
Randy Dunlap[1] found that LCS over FDDI has never worked, when FDDI
was compiled as module. Instead of fixing that, remove the FDDI option
from the lcs driver.
While at it, make the CONFIG_LCS description a bit more helpful.
References:
[1] https://lore.kernel.org/netdev/20230621213742.8245-1-rdunlap@infradead.org/
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230724131546.3597001-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter, wireless and ebpf.
Current release - regressions:
- netfilter: conntrack: gre: don't set assured flag for clash entries
- wifi: iwlwifi: remove 'use_tfh' config to fix crash
Previous releases - regressions:
- ipv6: fix a potential refcount underflow for idev
- icmp6: ifix null-ptr-deref of ip6_null_entry->rt6i_idev in
icmp6_dev()
- bpf: fix max stack depth check for async callbacks
- eth: mlx5e:
- check for NOT_READY flag state after locking
- fix page_pool page fragment tracking for XDP
- eth: igc:
- fix tx hang issue when QBV gate is closed
- fix corner cases for TSN offload
- eth: octeontx2-af: Move validation of ptp pointer before its usage
- eth: ena: fix shift-out-of-bounds in exponential backoff
Previous releases - always broken:
- core: prevent skb corruption on frag list segmentation
- sched:
- cls_fw: fix improper refcount update leads to use-after-free
- sch_qfq: account for stab overhead in qfq_enqueue
- netfilter:
- report use refcount overflow
- prevent OOB access in nft_byteorder_eval
- wifi: mt7921e: fix init command fail with enabled device
- eth: ocelot: fix oversize frame dropping for preemptible TCs
- eth: fec: recycle pages for transmitted XDP frames"
* tag 'net-6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (79 commits)
selftests: tc-testing: add test for qfq with stab overhead
net/sched: sch_qfq: account for stab overhead in qfq_enqueue
selftests: tc-testing: add tests for qfq mtu sanity check
net/sched: sch_qfq: reintroduce lmax bound check for MTU
wifi: cfg80211: fix receiving mesh packets without RFC1042 header
wifi: rtw89: debug: fix error code in rtw89_debug_priv_send_h2c_set()
net: txgbe: fix eeprom calculation error
net/sched: make psched_mtu() RTNL-less safe
net: ena: fix shift-out-of-bounds in exponential backoff
netdevsim: fix uninitialized data in nsim_dev_trap_fa_cookie_write()
net/sched: flower: Ensure both minimum and maximum ports are specified
MAINTAINERS: Add another mailing list for QUALCOMM ETHQOS ETHERNET DRIVER
docs: netdev: update the URL of the status page
wifi: iwlwifi: remove 'use_tfh' config to fix crash
xdp: use trusted arguments in XDP hints kfuncs
bpf: cpumap: Fix memory leak in cpu_map_update_elem
wifi: airo: avoid uninitialized warning in airo_get_rate()
octeontx2-pf: Add additional check for MCAM rules
net: dsa: Removed unneeded of_node_put in felix_parse_ports_node
net: fec: use netdev_err_once() instead of netdev_err()
...
|
|
When ism_unregister_client() is called but the client still has DMBs
registered it returns -EBUSY and prints an error. This only happens
after the client has already been unregistered however. This is
unexpected as the unregister claims to have failed. Furthermore as this
implies a client bug a WARN() is more appropriate. Thus move the
deregistration after the check and use WARN().
Fixes: 89e7d2ba61b7 ("net/ism: Add new API for client registration")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the clients_lock was protecting the clients array against
concurrent addition/removal of clients but was also accessed from IRQ
context. This meant that it had to be a spinlock and that the add() and
remove() callbacks in which clients need to do allocation and take
mutexes can't be called under the clients_lock. To work around this these
callbacks were moved to workqueues. This not only introduced significant
complexity but is also subtly broken in at least one way.
In ism_dev_init() and ism_dev_exit() clients[i]->tgt_ism is used to
communicate the added/removed ISM device to the work function. While
write access to client[i]->tgt_ism is protected by the clients_lock and
the code waits that there is no pending add/remove work before and after
setting clients[i]->tgt_ism this is not enough. The problem is that the
wait happens based on per ISM device counters. Thus a concurrent
ism_dev_init()/ism_dev_exit() for a different ISM device may overwrite
a clients[i]->tgt_ism between unlocking the clients_lock and the
subsequent wait for the work to finnish.
Thankfully with the clients_lock no longer held in IRQ context it can be
turned into a mutex which can be held during the calls to add()/remove()
completely removing the need for the workqueues and the associated
broken housekeeping including the per ISM device counters and the
clients[i]->tgt_ism.
Fixes: 89e7d2ba61b7 ("net/ism: Add new API for client registration")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clients array references all registered clients and is protected by
the clients_lock. Besides its use as general list of clients the clients
array is accessed in ism_handle_irq() to forward ISM device events to
clients.
While the clients_lock is taken in the IRQ handler when calling
handle_event() it is however incorrectly not held during the
client->handle_irq() call and for the preceding clients[] access leaving
it unprotected against concurrent client (un-)registration.
Furthermore the accesses to ism->sba_client_arr[] in ism_register_dmb()
and ism_unregister_dmb() are not protected by any lock. This is
especially problematic as the client ID from the ism->sba_client_arr[]
is not checked against NO_CLIENT and neither is the client pointer
checked.
Instead of expanding the use of the clients_lock further add a separate
array in struct ism_dev which references clients subscribed to the
device's events and IRQs. This array is protected by ism->lock which is
already taken in ism_handle_irq() and can be taken outside the IRQ
handler when adding/removing subscribers or the accessing
ism->sba_client_arr[]. This also means that the clients_lock is no
longer taken in IRQ context.
Fixes: 89e7d2ba61b7 ("net/ism: Add new API for client registration")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- Fix virtual vs physical address confusion in vmem_add_range() and
vmem_remove_range() functions
- Include <linux/io.h> instead of <asm/io.h> and <asm-generic/io.h>
throughout s390 code
- Make all PSW related defines also available for assembler files.
Remove PSW_DEFAULT_KEY define from uapi for that
- When adding an undefined symbol the build still succeeds, but
userspace crashes trying to execute VDSO, because the symbol is not
resolved. Add undefined symbols check to prevent that
- Use kvmalloc_array() instead of kzalloc() for allocaton of 256k
memory when executing s390 crypto adapter IOCTL
- Add -fPIE flag to prevent decompressor misaligned symbol build error
with clang
- Use .balign instead of .align everywhere. This is a no-op for s390,
but with this there no mix in using .align and .balign anymore
- Filter out -mno-pic-data-is-text-relative flag when compiling kernel
to prevent VDSO build error
- Rework entering of DAT-on mode on CPU restart to use PSW_KERNEL_BITS
mask directly
- Do not retry administrative requests to some s390 crypto cards, since
the firmware assumes replay attacks
- Remove most of the debug code, which is build in when kernel config
option CONFIG_ZCRYPT_DEBUG is enabled
- Remove CONFIG_ZCRYPT_MULTIDEVNODES kernel config option and switch
off the multiple devices support for the s390 zcrypt device driver
- With the conversion to generic entry machine checks are accounted to
the current context instead of irq time. As result, the STCKF
instruction at the beginning of the machine check handler and the
lowcore member are no longer required, therefore remove it
- Fix various typos found with codespell
- Minor cleanups to CPU-measurement Counter and Sampling Facilities
code
- Revert patch that removes VMEM_MAX_PHYS macro, since it causes a
regression
* tag 's390-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (25 commits)
Revert "s390/mm: get rid of VMEM_MAX_PHYS macro"
s390/cpum_sf: remove check on CPU being online
s390/cpum_sf: handle casts consistently
s390/cpum_sf: remove unnecessary debug statement
s390/cpum_sf: remove parameter in call to pr_err
s390/cpum_sf: simplify function setup_pmu_cpu
s390/cpum_cf: remove unneeded debug statements
s390/entry: remove mcck clock
s390: fix various typos
s390/zcrypt: remove ZCRYPT_MULTIDEVNODES kernel config option
s390/zcrypt: do not retry administrative requests
s390/zcrypt: cleanup some debug code
s390/entry: rework entering DAT-on mode on CPU restart
s390/mm: fence off VM macros from asm and linker
s390: include linux/io.h instead of asm/io.h
s390/ptrace: make all psw related defines also available for asm
s390/ptrace: remove PSW_DEFAULT_KEY from uapi
s390/vdso: filter out mno-pic-data-is-text-relative cflag
s390: consistently use .balign instead of .align
s390/decompressor: fix misaligned symbol build error
...
|
|
Change boolean parameter of function "qeth_l3_vipa_store" inside the
"qeth_l3_dev_vipa_del4_store" function from "true" to "false" because
"true" is used for adding a virtual ip address and "false" for deleting.
Fixes: 2390166a6b45 ("s390/qeth: clean up L3 sysfs code")
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Include linux/io.h instead of asm/io.h everywhere. linux/io.h includes
asm/io.h, so this shouldn't cause any problems. Instead this might help for
some randconfig build errors which were reported due to some undefined io
related functions.
Also move the changed include so it stays grouped together with other
includes from the same directory.
For ctcm_mpc.c also remove not needed comments (actually questions).
Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
The referenced patch is causing build errors when ETHERNET=y and
FDDI=m. While we work out the preferred patch(es), revert this patch
to make the pain go away.
Fixes: 128272336120 ("s390/net: lcs: use IS_ENABLED() for kconfig detection")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: lore.kernel.org/r/202306202129.pl0AqK8G-lkp@intel.com
Cc: Alexandra Winter <wintera@linux.ibm.com>
Cc: Wenjia Zhang <wenjia@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230622155409.27311-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This LWN article explains the why scnprintf is preferred over snprintf
in general
https://lwn.net/Articles/69419/
Ie. snprintf() returns what *would* be the resulting length, while
scnprintf() returns the actual length.
Note that ctcm_print_statistics() writes the data into the kernel log
and is therefore not suitable for sysfs_emit(). Observable behavior is
not changed, as there may be dependencies.
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Following the advice of the Documentation/filesystems/sysfs.rst.
All sysfs related show()-functions should only use sysfs_emit() or
sysfs_emit_at() when formatting the value to be returned to user space.
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This LWN article explains the why scnprintf is preferred over snprintf
in general
https://lwn.net/Articles/69419/
Ie. snprintf() returns what *would* be the resulting length, while
scnprintf() returns the actual length.
Reported-by: Jules Irenge <jbi.octave@gmail.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Following the advice of the Documentation/filesystems/sysfs.rst.
All sysfs related show()-functions should only use sysfs_emit() or
sysfs_emit_at() when formatting the value to be returned to user space.
While at it, follow Linux kernel coding style and unify indentation
Reported-by: Jules Irenge <jbi.octave@gmail.com>
Reported-by: Joe Perches <joe@perches.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When CONFIG_ETHERNET=m or CONFIG_FDDI=m, lcs.s has build errors or
warnings:
../drivers/s390/net/lcs.c:40:2: error: #error Cannot compile lcs.c without some net devices switched on.
40 | #error Cannot compile lcs.c without some net devices switched on.
../drivers/s390/net/lcs.c: In function 'lcs_startlan_auto':
../drivers/s390/net/lcs.c:1601:13: warning: unused variable 'rc' [-Wunused-variable]
1601 | int rc;
Solve this by using IS_ENABLED(CONFIG_symbol) instead of ifdef
CONFIG_symbol. The latter only works for builtin (=y) values
while IS_ENABLED() works for builtin or modular values.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexandra Winter <wintera@linux.ibm.com>
Cc: Wenjia Zhang <wenjia@linux.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
include/linux/mlx5/driver.h
617f5db1a626 ("RDMA/mlx5: Fix affinity assignment")
dc13180824b7 ("net/mlx5: Enable devlink port for embedded cpu VF vports")
https://lore.kernel.org/all/20230613125939.595e50b8@canb.auug.org.au/
tools/testing/selftests/net/mptcp/mptcp_join.sh
47867f0a7e83 ("selftests: mptcp: join: skip check if MIB counter not supported")
425ba803124b ("selftests: mptcp: join: support RM_ADDR for used endpoints or not")
45b1a1227a7a ("mptcp: introduces more address related mibs")
0639fa230a21 ("selftests: mptcp: add explicit check for new mibs")
https://lore.kernel.org/netdev/20230609-upstream-net-20230610-mptcp-selftests-support-old-kernels-part-3-v1-0-2896fe2ee8a3@tessares.net/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch prevents the system from crashing when unloading the ISM module.
How to reproduce: Attach an ISM device and execute 'rmmod ism'.
Error-Log:
- Trying to free already-free IRQ 0
- WARNING: CPU: 1 PID: 966 at kernel/irq/manage.c:1890 free_irq+0x140/0x540
After calling ism_dev_exit() for each ISM device in the exit routine,
pci_unregister_driver() will execute ism_remove() for each ISM device.
Because ism_remove() also calls ism_dev_exit(),
free_irq(pci_irq_vector(pdev, 0), ism) is called twice for each ISM
device. This results in a crash with the error
'Trying to free already-free IRQ'.
In the exit routine, it is enough to call pci_unregister_driver()
because it ensures that ism_dev_exit() is called once per
ISM device.
Cc: <stable@vger.kernel.org> # 6.3+
Fixes: 89e7d2ba61b7 ("net/ism: Add new API for client registration")
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Julian Ruess <julianr@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A future change will convert the DMA API implementation from the
architecture specific arch/s390/pci/pci_dma.c to using the common code
drivers/iommu/dma-iommu.c which the utilizes the same IOMMU hardware
through the s390-iommu driver. Unlike the s390 specific DMA API this
requires devices to correctly set the coherent mask to be allowed to use
IOVAs >2^32 in dma_alloc_coherent(). This was however not done for ISM
devices. ISM requires such addresses since currently the DMA aperture
for PCI devices starts at 2^32 and all calls to dma_alloc_coherent()
would thus fail.
Link: https://lore.kernel.org/all/20230310-dma_iommu-v9-1-65bb8edd2beb@linux.ibm.com/
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230524075411.3734141-1-schnelle@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, v2 support was derived from a very specific format of the SEID
as part of the SMC-D codebase. Make this part of the SMC-D device API, so
implementers do not need to adhere to a specific SEID format.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Reviewed-and-tested-by: Jan Karcher <jaka@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This LWN article explains the rationale for this change
https: //lwn.net/Articles/69419/
Ie. snprintf() returns what *would* be the resulting length,
while scnprintf() returns the actual length.
Reported-by: Jules Irenge <jbi.octave@gmail.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Following the advice of the Documentation/filesystems/sysfs.rst.
All sysfs related show()-functions should only use sysfs_emit() or
sysfs_emit_at() when formatting the value to be returned to user space.
Reported-by: Jules Irenge <jbi.octave@gmail.com>
Reported-by: Joe Perches <joe@perches.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use INET6_ADDRSTRLEN constant with size of 48 which be used for char arrays
storing ip addresses (for IPv4 and IPv6)
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Get rid of multiple smatch warnings, like:
warn: inconsistent indenting
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The struct device for ISM devices was part of struct smcd_dev. Move to
struct ism_dev, provide a new API call in struct smcd_ops, and convert
existing SMCD code accordingly.
Furthermore, remove struct smcd_dev from struct ism_dev.
This is the final part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ism module had SMC-D-specific code sprinkled across the entire module.
We are now consolidating the SMC-D-specific parts into the latter parts
of the module, so it becomes more clear what code is intended for use with
ISM, and which parts are glue code for usage in the context of SMC-D.
This is the fourth part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We separate the code implementing the struct smcd_ops API in the ISM
device driver from the functions that may be used by other exploiters of
ISM devices.
Note: We start out small, and don't offer the whole breadth of the ISM
device for public use, as many functions are specific to or likely only
ever used in the context of SMC-D.
This is the third part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register the smc module with the new ism device driver API.
This is the second part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new API that allows other drivers to concurrently access ISM devices.
To do so, we introduce a new API that allows other modules to register for
ISM device usage. Furthermore, we move the GID to struct ism, where it
belongs conceptually, and rename and relocate struct smcd_event to struct
ism_event.
This is the first part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conceptually, a DMB is a structure that belongs to ISM devices. However,
SMC currently 'owns' this structure. So future exploiters of ISM devices
would be forced to include SMC headers to work - which is just weird.
Therefore, we switch ISM to struct ism_dmb, introduce a new public header
with the definition (will be populated with further API calls later on),
and, add a thin wrapper to please SMC. Since structs smcd_dmb and ism_dmb
are identical, we can simply convert between the two for now.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Follow the advice of the Documentation/filesystems/sysfs.rst
and show() should only use sysfs_emit() or sysfs_emit_at()
when formatting the value to be returned to user space.
Signed-off-by: Xuezhi Zhang <zhangxuezhi1@coolpad.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- reduce the swiotlb buffer size on allocation failure (Alexey
Kardashevskiy)
- clean up passing of bogus GFP flags to the dma-coherent allocator
(Christoph Hellwig)
* tag 'dma-mapping-6.2-2022-12-13' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: reject __GFP_COMP in dma_alloc_attrs
ALSA: memalloc: don't pass bogus GFP_ flags to dma_alloc_*
s390/ism: don't pass bogus GFP_ flags to dma_alloc_coherent
cnic: don't pass bogus GFP_ flags to dma_alloc_coherent
RDMA/qib: don't pass bogus GFP_ flags to dma_alloc_coherent
RDMA/hfi1: don't pass bogus GFP_ flags to dma_alloc_coherent
media: videobuf-dma-contig: use dma_mmap_coherent
swiotlb: reduce the swiotlb buffer size on allocation failure
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KASAN found that addr was dereferenced after br2dev_event_work was freed.
==================================================================
BUG: KASAN: use-after-free in qeth_l2_br2dev_worker+0x5ba/0x6b0
Read of size 1 at addr 00000000fdcea440 by task kworker/u760:4/540
CPU: 17 PID: 540 Comm: kworker/u760:4 Tainted: G E 6.1.0-20221128.rc7.git1.5aa3bed4ce83.300.fc36.s390x+kasan #1
Hardware name: IBM 8561 T01 703 (LPAR)
Workqueue: 0.0.8000_event qeth_l2_br2dev_worker
Call Trace:
[<000000016944d4ce>] dump_stack_lvl+0xc6/0xf8
[<000000016942cd9c>] print_address_description.constprop.0+0x34/0x2a0
[<000000016942d118>] print_report+0x110/0x1f8
[<0000000167a7bd04>] kasan_report+0xfc/0x128
[<000000016938d79a>] qeth_l2_br2dev_worker+0x5ba/0x6b0
[<00000001673edd1e>] process_one_work+0x76e/0x1128
[<00000001673ee85c>] worker_thread+0x184/0x1098
[<000000016740718a>] kthread+0x26a/0x310
[<00000001672c606a>] __ret_from_fork+0x8a/0xe8
[<00000001694711da>] ret_from_fork+0xa/0x40
Allocated by task 108338:
kasan_save_stack+0x40/0x68
kasan_set_track+0x36/0x48
__kasan_kmalloc+0xa0/0xc0
qeth_l2_switchdev_event+0x25a/0x738
atomic_notifier_call_chain+0x9c/0xf8
br_switchdev_fdb_notify+0xf4/0x110
fdb_notify+0x122/0x180
fdb_add_entry.constprop.0.isra.0+0x312/0x558
br_fdb_add+0x59e/0x858
rtnl_fdb_add+0x58a/0x928
rtnetlink_rcv_msg+0x5f8/0x8d8
netlink_rcv_skb+0x1f2/0x408
netlink_unicast+0x570/0x790
netlink_sendmsg+0x752/0xbe0
sock_sendmsg+0xca/0x110
____sys_sendmsg+0x510/0x6a8
___sys_sendmsg+0x12a/0x180
__sys_sendmsg+0xe6/0x168
__do_sys_socketcall+0x3c8/0x468
do_syscall+0x22c/0x328
__do_syscall+0x94/0xf0
system_call+0x82/0xb0
Freed by task 540:
kasan_save_stack+0x40/0x68
kasan_set_track+0x36/0x48
kasan_save_free_info+0x4c/0x68
____kasan_slab_free+0x14e/0x1a8
__kasan_slab_free+0x24/0x30
__kmem_cache_free+0x168/0x338
qeth_l2_br2dev_worker+0x154/0x6b0
process_one_work+0x76e/0x1128
worker_thread+0x184/0x1098
kthread+0x26a/0x310
__ret_from_fork+0x8a/0xe8
ret_from_fork+0xa/0x40
Last potentially related work creation:
kasan_save_stack+0x40/0x68
__kasan_record_aux_stack+0xbe/0xd0
insert_work+0x56/0x2e8
__queue_work+0x4ce/0xd10
queue_work_on+0xf4/0x100
qeth_l2_switchdev_event+0x520/0x738
atomic_notifier_call_chain+0x9c/0xf8
br_switchdev_fdb_notify+0xf4/0x110
fdb_notify+0x122/0x180
fdb_add_entry.constprop.0.isra.0+0x312/0x558
br_fdb_add+0x59e/0x858
rtnl_fdb_add+0x58a/0x928
rtnetlink_rcv_msg+0x5f8/0x8d8
netlink_rcv_skb+0x1f2/0x408
netlink_unicast+0x570/0x790
netlink_sendmsg+0x752/0xbe0
sock_sendmsg+0xca/0x110
____sys_sendmsg+0x510/0x6a8
___sys_sendmsg+0x12a/0x180
__sys_sendmsg+0xe6/0x168
__do_sys_socketcall+0x3c8/0x468
do_syscall+0x22c/0x328
__do_syscall+0x94/0xf0
system_call+0x82/0xb0
Second to last potentially related work creation:
kasan_save_stack+0x40/0x68
__kasan_record_aux_stack+0xbe/0xd0
kvfree_call_rcu+0xb2/0x760
kernfs_unlink_open_file+0x348/0x430
kernfs_fop_release+0xc2/0x320
__fput+0x1ae/0x768
task_work_run+0x1bc/0x298
exit_to_user_mode_prepare+0x1a0/0x1a8
__do_syscall+0x94/0xf0
system_call+0x82/0xb0
The buggy address belongs to the object at 00000000fdcea400
which belongs to the cache kmalloc-96 of size 96
The buggy address is located 64 bytes inside of
96-byte region [00000000fdcea400, 00000000fdcea460)
The buggy address belongs to the physical page:
page:000000005a9c26e8 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0xfdcea
flags: 0x3ffff00000000200(slab|node=0|zone=1|lastcpupid=0x1ffff)
raw: 3ffff00000000200 0000000000000000 0000000100000122 000000008008cc00
raw: 0000000000000000 0020004100000000 ffffffff00000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
00000000fdcea300: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
00000000fdcea380: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
>00000000fdcea400: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
^
00000000fdcea480: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
00000000fdcea500: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
==================================================================
Fixes: f7936b7b2663 ("s390/qeth: Update MACs of LEARNING_SYNC device")
Reported-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Link: https://lore.kernel.org/r/20221207105304.20494-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
dma_alloc_coherent is an opaque allocator that only uses the GFP_ flags
for allocation context control. Don't pass __GFP_COMP which makes no
sense for an allocation that can't in any way be converted to a page
pointer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Wenjia Zhang <wenjia@linux.ibm.com>
|
|
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/lcs.c:2090:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
drivers/s390/net/lcs.c:2097:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of lcs_start_xmit() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/netiucv.c:1854:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = netiucv_tx,
^~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of netiucv_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/ctcm_main.c:1064:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcm_tx,
^~~~~~~
drivers/s390/net/ctcm_main.c:1072:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = ctcmpc_tx,
^~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of ctc{mp,}m_tx() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future.
Additionally, while in the area, remove a comment block that is no
longer relevant.
Link: https://github.com/ClangBuiltLinux/linux/issues/1750
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|