Age | Commit message (Collapse) | Author | Files | Lines |
|
For z/VM NICs, qeth needs to consider which of the three CCW devices in
an MPC group it uses for requesting a managed MAC address.
On the Base device, the hypervisor returns a default MAC which is
pre-assigned when creating the NIC (this MAC is also returned by the
READ MAC primitive). Querying any other device results in the allocation
of an additional MAC address.
For consistency with READ MAC and to avoid using up more addresses than
necessary, it is preferable to use the NIC's default MAC. So switch the
the diag26c over to using a NIC's Read device, which should always be
identical to the Base device.
Fixes: ec61bd2fd2a2 ("s390/qeth: use diag26c to get MAC address on L2")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Submitting a cmd IO request (usually on the WRITE device, but for IDX
also on the READ device) is currently done with ccw_device_start()
and a manual timeout in the caller.
On timeout, the caller cleans up the related resources (eg. IO buffer).
But 1) the IO might still be active and utilize those resources, and
2) when the IO completes, qeth_irq() will attempt to clean up the
same resources again.
Instead of introducing additional resource locking, switch to
ccw_device_start_timeout() to ensure IO termination after timeout, and
let the IRQ handler alone deal with cleaning up after a request.
This also removes a stray write->irq_pending reset from
clear_ipacmd_list(). The routine doesn't terminate any pending IO on
the WRITE device, so this should be handled properly via IO timeout
in the IRQ handler.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing the MAC address on a L2 qeth device, current code first
unregisters the old address, then registers the new one.
If HW rejects the new address (or the IO fails), the device ends up with
no operable address at all.
Re-order the code flow so that the old address only gets dropped if the
new address was registered successfully. While at it, add logic to catch
some corner-cases.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Creating the global workqueue during driver init may fail, deal with it.
Also, destroy the created workqueue on any subsequent error.
Fixes: 0f54761d167f ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For control IO, qeth currently tracks the index of the buffer that it
expects to complete the next IO on each qeth_channel. If the channel
presents an IRQ while this buffer has not yet completed, no completion
processing for _any_ completed buffer takes place.
So if the 'next buffer' is skipped for any sort of reason* (eg. when it
is released due to error conditions, before the IO is started), the
buffer obviously won't switch to PROCESSED until it is eventually
allocated for a _different_ IO and completes.
Until this happens, all completion processing on that channel stalls
and pending requests possibly time out.
As a fix, remove the whole 'next buffer' logic and simply process any
IO buffer right when it completes. A channel will never have more than
one IO pending, so there's no risk of processing out-of-sequence.
*Note: currently just one location in the code really handles this problem,
by advancing the 'next' index manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to check both return code fields before(!) processing the
command response. Otherwise we risk operating on invalid data.
This matches an earlier fix for SETASSPARMS commands, see
commit ad3cbf613329 ("s390/qeth: fix error handling in checksum cmd callback").
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removing couple of duplicate includes, found by "make includecheck".
That leaves 1 duplicate include in arch/s390/kernel/entry.S, which is
there for a reason (it includes generated asm/syscall_table.h twice).
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The module exit function of the smsgiucv module uses the incorrect CP
command to disable SMSG messages. The correct command is "SET SMSG OFF".
Use it.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
sclp_early_printk could be used before .bss section is zeroed
(i.e. from als.c during the decompressor phase), therefore values used
by sclp_early_printk should be located in the .data section.
Another reason for that is to avoid potential initrd corruption, if some
code in future would use sclp_early_printk before initrd is moved from
possibly overlapping with .bss section region to a safe location.
Fixes: 0b0d1173d8ae ("s390/sclp: 32 bit event mask compatibility mode")
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Martin Schwidefsky:
"Three notable larger changes next to the usual bug fixing:
- update the email addresses in MAINTAINERS for the s390 folks to use
the simpler linux.ibm.com domain instead of the old
linux.vnet.ibm.com
- an update for the zcrypt device driver that removes some old and
obsolete interfaces and add support for up to 256 crypto adapters
- a rework of the IPL aka boot code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (23 commits)
s390: correct nospec auto detection init order
s390/zcrypt: Support up to 256 crypto adapters.
s390/zcrypt: Remove deprecated zcrypt proc interface.
s390/zcrypt: Remove deprecated ioctls.
s390/zcrypt: Make ap init functions static.
MAINTAINERS: update s390 maintainers email addresses
s390/ipl: remove reipl_method and dump_method
s390/ipl: correct kdump reipl block checksum calculation
s390/ipl: remove non-existing functions declaration
s390: assume diag308 set always works
s390/ipl: avoid adding scpdata to cmdline during ftp/dvd boot
s390/ipl: correct ipl parmblock valid checks
s390/ipl: rely on diag308 store to get ipl info
s390/ipl: move ipl_flags to ipl.c
s390/ipl: get rid of ipl_ssid and ipl_devno
s390/ipl: unite diag308 and scsi boot ipl blocks
s390/ipl: ensure loadparm valid flag is set
s390/qdio: lock device while installing IRQ handler
s390/qdio: clear intparm during shutdown
s390/ccwgroup: require at least one ccw device
...
|
|
There was an artificial restriction on the card/adapter id
to only 6 bits but all the AP commands do support adapter
ids with 8 bit. This patch removes this restriction to 64
adapters and now up to 256 adapter can get addressed.
Some of the ioctl calls work on the max number of cards
possible (which was 64). These ioctls are now deprecated
but still supported. All the defines, structs and ioctl
interface declarations have been kept for compabibility.
There are now new ioctls (and defines for these) with an
additional '2' appended which provide the extended versions
with 256 cards supported.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This cycle was was not something I ever want to repeat as there were
several late changes that have only now just settled.
Half of the branch up to commit d2c997c0f145 ("fs, dax: use
page->mapping to warn...") have been in -next for several releases.
The of_pmem driver and the address range scrub rework were late
arrivals, and the dax work was scaled back at the last moment.
The of_pmem driver missed a previous merge window due to an oversight.
A sense of obligation to rectify that miss is why it is included for
4.17. It has acks from PowerPC folks. Stephen reported a build failure
that only occurs when merging it with your latest tree, for now I have
fixed that up by disabling modular builds of of_pmem. A test merge
with your tree has received a build success report from the 0day robot
over 156 configs.
An initial version of the ARS rework was submitted before the merge
window. It is self contained to libnvdimm, a net code reduction, and
passing all unit tests.
The filesystem-dax changes are based on the wait_var_event()
functionality from tip/sched/core. However, late review feedback
showed that those changes regressed truncate performance to a large
degree. The branch was rewound to drop the truncate behavior change
and now only includes preparation patches and cleanups (with full acks
and reviews). The finalization of this dax-dma-vs-trnucate work will
need to wait for 4.18.
Summary:
- A rework of the filesytem-dax implementation provides for detection
of unmap operations (truncate / hole punch) colliding with
in-progress device-DMA. A fix for these collisions remains a
work-in-progress pending resolution of truncate latency and
starvation regressions.
- The of_pmem driver expands the users of libnvdimm outside of x86
and ACPI to describe an implementation of persistent memory on
PowerPC with Open Firmware / Device tree.
- Address Range Scrub (ARS) handling is completely rewritten to
account for the fact that ARS may run for 100s of seconds and there
is no platform defined way to cancel it. ARS will now no longer
block namespace initialization.
- The NVDIMM Namespace Label implementation is updated to handle
label areas as small as 1K, down from 128K.
- Miscellaneous cleanups and updates to unit test infrastructure"
* tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (39 commits)
libnvdimm, of_pmem: workaround OF_NUMA=n build error
nfit, address-range-scrub: add module option to skip initial ars
nfit, address-range-scrub: rework and simplify ARS state machine
nfit, address-range-scrub: determine one platform max_ars value
powerpc/powernv: Create platform devs for nvdimm buses
doc/devicetree: Persistent memory region bindings
libnvdimm: Add device-tree based driver
libnvdimm: Add of_node to region and bus descriptors
libnvdimm, region: quiet region probe
libnvdimm, namespace: use a safe lookup for dimm device name
libnvdimm, dimm: fix dpa reservation vs uninitialized label area
libnvdimm, testing: update the default smart ctrl_temperature
libnvdimm, testing: Add emulation for smart injection commands
nfit, address-range-scrub: introduce nfit_spa->ars_state
libnvdimm: add an api to cast a 'struct nd_region' to its 'struct device'
nfit, address-range-scrub: fix scrub in-progress reporting
dax, dm: allow device-mapper to operate without dax support
dax: introduce CONFIG_DAX_DRIVER
fs, dax: use page->mapping to warn if truncate collides with a busy page
ext2, dax: introduce ext2_dax_aops
...
|
|
This patch removes the deprecated zcrypt proc interface.
It is outdated and deprecated and does not support the
latest 3 generations of CEX cards.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This patch removes the old status calls which have been marked
as deprecated since at least 2 years now. There is no known
application or library relying on these ioctls any more.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The ap init functions ap_module_init and ap_debug_init are
only used within ap_bus.c. Make these functions static and
do not declare them in any header file any more.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
diag308 set has been available for many machine generations, and
alternative reipl code paths has not been exercised and seems to be
broken without noticing for a while now. So, cleaning up all obsolete
reipl methods except currently used ones, assuming that diag308 set
always works.
Also removing not longer needed reset callbacks.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
For both ccw and fcp boot retrieve ipl info from ipl block received via
diag308 store. Old scsi ipl parm block handling and cio_get_iplinfo are
removed. Ipl type is deducted from ipl block (if valid).
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
During setup, qdio takes control of the presented ccw device and replaces
the device's IRQ handler with its own. To avoid any interference with
conccurent activity on the device, this should be done while holding the
device's lock.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
During shutdown, qdio returns its ccw device back to control by the
upper-layer driver. But there is a remote chance that by the time where the
IRQ handler gets switched back, the interrupt for the preceding
ccw_device_{clear,halt} hasn't been presented yet.
Upper-layer drivers would then need to handle this IRQ - and since the IO
is issued with an intparm, it could very well be confused with whatever
intparm mechanism the driver uses itself (eg intparm == request address).
So when switching over the IRQ handler, also clear the intparm and have
upper-layer drivers deal with any such delayed interrupt as if it was
unsolicited.
Suggested-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
ccwgroup_create_dev() derives the gdev's device name from gdev->cdev[0],
so make sure that this reference is valid.
For robustness only, all current ccwgroup drivers get this right.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The AP bus code is not available as kernel module any more.
There was some leftover code dealing with kernel module
exit which has been removed with this patch.
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- Improvements for the spectre defense:
* The spectre related code is consolidated to a single file
nospec-branch.c
* Automatic enable/disable for the spectre v2 defenses (expoline vs.
nobp)
* Syslog messages for specve v2 are added
* Enable CONFIG_GENERIC_CPU_VULNERABILITIES and define the attribute
functions for spectre v1 and v2
- Add helper macros for assembler alternatives and use them to shorten
the code in entry.S.
- Add support for persistent configuration data via the SCLP Store Data
interface. The H/W interface requires a page table that uses 4K pages
only, the code to setup such an address space is added as well.
- Enable virtio GPU emulation in QEMU. To do this the depends
statements for a few common Kconfig options are modified.
- Add support for format-3 channel path descriptors and add a binary
sysfs interface to export the associated utility strings.
- Add a sysfs attribute to control the IFCC handling in case of
constant channel errors.
- The vfio-ccw changes from Cornelia.
- Bug fixes and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (40 commits)
s390/kvm: improve stack frame constants in entry.S
s390/lpp: use assembler alternatives for the LPP instruction
s390/entry.S: use assembler alternatives
s390: add assembler macros for CPU alternatives
s390: add sysfs attributes for spectre
s390: report spectre mitigation via syslog
s390: add automatic detection of the spectre defense
s390: move nobp parameter functions to nospec-branch.c
s390/cio: add util_string sysfs attribute
s390/chsc: query utility strings via fmt3 channel path descriptor
s390/cio: rename struct channel_path_desc
s390/cio: fix unbind of io_subchannel_driver
s390/qdio: split up CCQ handling for EQBS / SQBS
s390/qdio: don't retry EQBS after CCQ 96
s390/qdio: restrict buffer merging to eligible devices
s390/qdio: don't merge ERROR output buffers
s390/qdio: simplify math in get_*_buffer_frontier()
s390/decompressor: trim uncompressed image head during the build
s390/crypto: Fix kernel crash on aes_s390 module remove.
s390/defkeymap: fix global init to zero
...
|
|
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- add a shell script to get Clang version
- improve portability of build scripts
- drop always-enabled CONFIG_THIN_ARCHIVE and remove unused code
- rename built-in.o which is now thin archive to built-in.a
- process clean/build targets one by one to get along with -j option
- simplify ld-option
- improve building with CONFIG_TRIM_UNUSED_KSYMS
- define KBUILD_MODNAME even for objects shared among multiple modules
- avoid linking multiple instances of same objects from composite
objects
- move <linux/compiler_types.h> to c_flags to include it only for C
files
- clean-up various Makefiles
* tag 'kbuild-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (29 commits)
kbuild: get <linux/compiler_types.h> out of <linux/kconfig.h>
kbuild: clean up link rule of composite modules
kbuild: clean up archive rule of built-in.a
kbuild: remove partial section mismatch detection for built-in.a
net: liquidio: clean up Makefile for simpler composite object handling
lib: zstd: clean up Makefile for simpler composite object handling
kbuild: link $(real-obj-y) instead of $(obj-y) into built-in.a
kbuild: rename real-objs-y/m to real-obj-y/m
kbuild: move modname and modname-multi close to modname_flags
kbuild: simplify modname calculation
kbuild: fix modname for composite modules
kbuild: define KBUILD_MODNAME even if multiple modules share objects
kbuild: remove unnecessary $(subst $(obj)/, , ...) in modname-multi
kbuild: Use ls(1) instead of stat(1) to obtain file size
kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS
kbuild: move include/config/ksym/* to include/ksym/*
kbuild: move CONFIG_TRIM_UNUSED_KSYMS code unneeded for external module
kbuild: restore autoksyms.h touch to the top Makefile
kbuild: move 'scripts' target below
kbuild: remove wrong 'touch' in adjust_autoksyms.sh
...
|
|
In support of allowing device-mapper to compile out idle/dead code when
there are no dax providers in the system, introduce the DAX_DRIVER
symbol. This is selected by all leaf drivers that device-mapper might be
layered on top. This allows device-mapper to conditionally 'select DAX'
only when a provider is present.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Reported-by: Bart Van Assche <Bart.VanAssche@wdc.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Export utility strings as a chpid's binary sysfs attribute.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add support for format 3 channel path descriptors and use them to
gather utility strings.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Rename struct channel_path_desc to struct channel_path_desc_fmt0
to fit the scheme. Provide a macro for the function wrappers that
gather this and related data from firmware.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If the io_subchannel_driver is unbound from a subchannel it bluntly kills
all I/O on the subchannel and sets the ccw_device state to not operable
before deregistering the ccw_device. However, for online devices we should
set the device offline (disband path groups etc.) which does not happen if
the device is in not oper state.
Simply deregister the ccw device - ccw_device_remove is smart enough to set
the device offline properly. If everything fails call io_subchannel_quiesce
afterwards as a safeguard.
Reported-by: Shalini Chellathurai Saroja <shalini@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Get rid of the confusing two-stage translation in a hot path, and only
handle CCQs that we anticipate for the respective command. Any
unexpected value (such as CCQ 97 (rc == 1) for SQBS) should be
considered a severe HW/driver bug, and traced as such.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Immediate retry of EQBS after CCQ 96 means that we potentially misreport
the state of buffers inspected during the first EQBS call.
This occurs when
1. the first EQBS finds all inspected buffers still in the initial state
set by the driver (ie INPUT EMPTY or OUTPUT PRIMED),
2. the EQBS terminates early with CCQ 96, and
3. by the time that the second EQBS comes around, the state of those
previously inspected buffers has changed.
If the state reported by the second EQBS is 'driver-owned', all we know
is that the previous buffers are driver-owned now as well. But we can't
tell if they all have the same state. So for instance
- the second EQBS reports OUTPUT EMPTY, but any number of the previous
buffers could be OUTPUT ERROR by now,
- the second EQBS reports OUTPUT ERROR, but any number of the previous
buffers could be OUTPUT EMPTY by now.
Effectively, this can result in both over- and underreporting of errors.
If the state reported by the second EQBS is 'HW-owned', that doesn't
guarantee that the previous buffers have not been switched to
driver-owned in the mean time. So for instance
- the second EQBS reports INPUT EMPTY, but any number of the previous
buffers could be INPUT PRIMED (or INPUT ERROR) by now.
This would result in failure to process pending work on the queue. If
it's the final check before yielding initiative, this can cause
a (temporary) queue stall due to IRQ avoidance.
Fixes: 25f269f17316 ("[S390] qdio: EQBS retry after CCQ 96")
Cc: <stable@vger.kernel.org> #v3.2+
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Only attempt to merge PENDING into EMPTY buffers for devices where
the PENDING state is actually expected (ie. IQD with CQ).
This might speed up the hot path a little bit.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
On an Output queue, both EMPTY and PENDING buffer states imply that the
buffer is ready for completion-processing by the upper-layer drivers.
So for a non-QEBSM Output queue, get_buf_states() merges mixed
batches of PENDING and EMPTY buffers into one large batch of EMPTY
buffers. The upper-layer driver (ie. qeth) later distuingishes PENDING
from EMPTY by inspecting the slsb_state for
QDIO_OUTBUF_STATE_FLAG_PENDING.
But the merge logic in get_buf_states() contains a bug that causes us to
erronously also merge ERROR buffers into such a batch of EMPTY buffers
(ERROR is 0xaf, EMPTY is 0xa1; so ERROR & EMPTY == EMPTY).
Effectively, most outbound ERROR buffers are currently discarded
silently and processed as if they had succeeded.
Note that this affects _all_ non-QEBSM device types, not just IQD with CQ.
Fix it by explicitly spelling out the exact conditions for merging.
For extracting the "get initial state" part out of the loop, this relies
on the fact that get_buf_states() is never called with a count of 0. The
QEBSM path already strictly requires this, and the two callers with
variable 'count' make sure of it.
Fixes: 104ea556ee7f ("qdio: support asynchronous delivery of storage blocks")
Cc: <stable@vger.kernel.org> #v3.2+
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When determining the buffer count that get_buf_states() should
be queried for, 'count' is capped at 127 buffers.
So the check
q->first_to_check == (q->first_to_check + count) % 128
can be reduced to
count == 0
This helps to emphasize that get_buf_states() is really only
called with count > 0.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Incremental linking is gone, so rename built-in.o to built-in.a, which
is the usual extension for archive files.
This patch does two things, first is a simple search/replace:
git grep -l 'built-in\.o' | xargs sed -i 's/built-in\.o/built-in\.a/g'
The second is to invert nesting of nested text manipulations to avoid
filtering built-in.a out from libs-y2:
-libs-y2 := $(filter-out %.a, $(patsubst %/, %/built-in.a, $(libs-y)))
+libs-y2 := $(patsubst %/, %/built-in.a, $(filter-out %.a, $(libs-y)))
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f9524
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e61 (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Always validate XFRM esn replay attribute, from Florian Westphal.
2) Fix RCU read lock imbalance in xfrm_get_tos(), from Xin Long.
3) Don't try to get firmware dump if not loaded in iwlwifi, from Shaul
Triebitz.
4) Fix BPF helpers to deal with SCTP GSO SKBs properly, from Daniel
Axtens.
5) Fix some interrupt handling issues in e1000e driver, from Benjamin
Poitier.
6) Use strlcpy() in several ethtool get_strings methods, from Florian
Fainelli.
7) Fix rhlist dup insertion, from Paul Blakey.
8) Fix SKB leak in netem packet scheduler, from Alexey Kodanev.
9) Fix driver unload crash when link is up in smsc911x, from Jeremy
Linton.
10) Purge out invalid socket types in l2tp_tunnel_create(), from Eric
Dumazet.
11) Need to purge the write queue when TCP connections are aborted,
otherwise userspace using MSG_ZEROCOPY can't close the fd. From
Soheil Hassas Yeganeh.
12) Fix double free in error path of team driver, from Arkadi
Sharshevsky.
13) Filter fixes for hv_netvsc driver, from Stephen Hemminger.
14) Fix non-linear packet access in ipv6 ndisc code, from Lorenzo
Bianconi.
15) Properly filter out unsupported feature flags in macvlan driver,
from Shannon Nelson.
16) Don't request loading the diag module for a protocol if the protocol
itself is not even registered. From Xin Long.
17) If datagram connect fails in ipv6, make sure the socket state is
consistent afterwards. From Paolo Abeni.
18) Use after free in qed driver, from Dan Carpenter.
19) If received ipv4 PMTU is less than the min pmtu, lock the mtu in the
entry. From Sabrina Dubroca.
20) Fix sleep in atomic in tg3 driver, from Jonathan Toppins.
21) Fix vlan in vlan untagging in some situations, from Toshiaki Makita.
22) Fix double SKB free in genlmsg_mcast(). From Nicolas Dichtel.
23) Fix NULL derefs in error paths of tcf_*_init(), from Davide Caratti.
24) Unbalanced PM runtime calls in FEC driver, from Florian Fainelli.
25) Memory leak in gemini driver, from Igor Pylypiv.
26) IDR leaks in error paths of tcf_*_init() functions, from Davide
Caratti.
27) Need to use GFP_ATOMIC in seg6_build_state(), from David Lebrun.
28) Missing dev_put() in error path of macsec_newlink(), from Dan
Carpenter.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (201 commits)
macsec: missing dev_put() on error in macsec_newlink()
net: dsa: Fix functional dsa-loop dependency on FIXED_PHY
hv_netvsc: common detach logic
hv_netvsc: change GPAD teardown order on older versions
hv_netvsc: use RCU to fix concurrent rx and queue changes
hv_netvsc: disable NAPI before channel close
net/ipv6: Handle onlink flag with multipath routes
ppp: avoid loop in xmit recursion detection code
ipv6: sr: fix NULL pointer dereference when setting encap source address
ipv6: sr: fix scheduling in RCU when creating seg6 lwtunnel state
net: aquantia: driver version bump
net: aquantia: Implement pci shutdown callback
net: aquantia: Allow live mac address changes
net: aquantia: Add tx clean budget and valid budget handling logic
net: aquantia: Change inefficient wait loop on fw data reads
net: aquantia: Fix a regression with reset on old firmware
net: aquantia: Fix hardware reset when SPI may rarely hangup
s390/qeth: on channel error, reject further cmd requests
s390/qeth: lock read device while queueing next buffer
s390/qeth: when thread completes, wake up all waiters
...
|
|
When the IRQ handler determines that one of the cmd IO channels has
failed and schedules recovery, block any further cmd requests from
being submitted. The request would inevitably stall, and prevent the
recovery from making progress until the request times out.
This sort of error was observed after Live Guest Relocation, where
the pending IO on the READ channel intentionally gets terminated to
kick-start recovery. Simultaneously the guest executed SIOCETHTOOL,
triggering qeth to issue a QUERY CARD INFO command. The command
then stalled in the inoperabel WRITE channel.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For calling ccw_device_start(), issue_next_read() needs to hold the
device's ccwlock.
This is satisfied for the IRQ handler path (where qeth_irq() gets called
under the ccwlock), but we need explicit locking for the initial call by
the MPC initialization.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_wait_for_threads() is potentially called by multiple users, make
sure to notify all of them after qeth_clear_thread_running_bit()
adjusted the thread_running_mask. With no timeout, callers would
otherwise stall.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On removal, a qeth card's netdevice is currently not properly freed
because the call chain looks as follows:
qeth_core_remove_device(card)
lx_remove_device(card)
unregister_netdev(card->dev)
card->dev = NULL !!!
qeth_core_free_card(card)
if (card->dev) !!!
free_netdev(card->dev)
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/vfio-ccw into features
Pull vfio-ccw patches from Cornelia Huck:
A small documentation update, and reject transport mode requests
(which we don't support).
|
|
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
commit 8f50af49f564d4e5 ("s390/console: Make preferred console handling
more consistent") created a separate console state for the ascii
console. This has the side effect that we register no tty for the line
mode interface as soon as there an ascii interface as default console.
Under KVM this results in no getty program on the line mode tty if the
guest has both types of interfaces.
As we can have multiple ttys at the same time we do not want to disable
the tty on sclp_line0 under KVM. So instead of checking for the console
mode, we now check for the presence of the sclp line mode interface. As
z/VM multiplexes the line mode interface on the 32xx screen we continue
to disable the line mode tty for the z/VM case.
CC: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Fixes: 8f50af49f564d4e5 ("s390/console: Make preferred console handling more consistent")
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The Linux Virtual Terminal (VT) layer provides a default keymap
which is compiled when VT layer is enabled. But at the same time
we are also compiling the EBCDIC keymap and this causes the linker
to complain.
So let's rename the EBCDIC keymap variables to prevent linker
conflict.
Signed-off-by: Farhan Ali <alifm@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <f670a2698d2372e1e990c48a29334ffe894804b1.1519315352.git.alifm@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The zfcp driver wants to know the timeout for a bsg job, so add a field
to struct bsg_job for it in preparation of not exposing the request
to the bsg-lib users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Using up 8 bytes in every ipaddr object to store SETIP/DELIP flags is
rather wasteful. Except for takeover eligibility, the flag values all
just depend on the address type, so determine them on demand.
While at it reorder the struct to fill an alignment hole.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reduce code duplication.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On an IP event, current code tries to determine if the netdev belongs
to a L3 card by walking all qeth cards in the system, and then all of
their VLAN devices too. Short-cut the whole thing by identifying a L3
device through its netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|