| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The variable 'op' is assigned a value and is never read. The variable is
not used and is redundant, remove it.
Link: https://lore.kernel.org/r/20220517092518.93159-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The memories for the slot should be observed to be written prior to
observing the slot as ready.
Prior to commit 26fc0ea74fcb ("scsi: libsas: Drop SAS_TASK_AT_INITIATOR"),
we had a spin_lock() + spin_unlock() immediately before marking the slot as
ready. The spin_unlock() - with release semantics - caused the slot memory
to be observed to be written.
Now that the spin_lock() + spin_unlock() is gone, use a smp_wmb().
Link: https://lore.kernel.org/r/1652774661-12935-1-git-send-email-john.garry@huawei.com
Fixes: 26fc0ea74fcb ("scsi: libsas: Drop SAS_TASK_AT_INITIATOR")
Reported-by: Yihang Li <liyihang6@hisilicon.com>
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Cisco VIC supports only 47 bits. If the host sends DMA addresses that are
greater than 47 bits, it causes work queue (WQ) errors in the VIC.
Link: https://lore.kernel.org/r/20220513205605.81788-1-kartilak@cisco.com
Tested-by: Karan Tilak Kumar <kartilak@cisco.com>
Co-developed-by: Dhanraj Jhawar <djhawar@cisco.com>
Signed-off-by: Dhanraj Jhawar <djhawar@cisco.com>
Co-developed-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add sysfs attributes for exposing target device details such as SAS
address, firmware device handle, and persistent ID for the
controller-attached devices and RAID volumes.
Link: https://lore.kernel.org/r/20220517115310.13062-3-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add shost related sysfs attributes to display the controller's firmware
version, queue depth, number of requests, and number of reply queues. Also
add an attribute to set & get the logging_level.
Link: https://lore.kernel.org/r/20220517115310.13062-2-sreekanth.reddy@broadcom.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As memset() of bmbx is immediately followed by a memcpy() where bmbx is the
destination, the memset() is redundant.
Link: https://lore.kernel.org/r/20220505143703.45441-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As memset() of scmd->sense_buffer is immediately followed by a memcpy()
where scmd->sense_buffer is the destination. The memset() is redundant.
Link: https://lore.kernel.org/r/20220505143214.44908-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Return -ENOMEM instead of success if dma_alloc_coherent() fails.
Link: https://lore.kernel.org/r/YnOmMGHqCOtUCYQ1@kili
Fixes: 43ca11005098 ("scsi: mpi3mr: Add support for PEL commands")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Removing an ATA device via sysfs means that the device may not be found
through re-scanning:
root@ubuntu:/home/john# lsscsi
[0:0:0:0] disk SanDisk LT0200MO P404 /dev/sda
[0:0:1:0] disk ATA HGST HUS724040AL A8B0 /dev/sdb
[0:0:8:0] enclosu 12G SAS Expander RevB -
root@ubuntu:/home/john# echo 1 > /sys/block/sdb/device/delete
root@ubuntu:/home/john# echo "- - -" > /sys/class/scsi_host/host0/scan
root@ubuntu:/home/john# lsscsi
[0:0:0:0] disk SanDisk LT0200MO P404 /dev/sda
[0:0:8:0] enclosu 12G SAS Expander RevB -
root@ubuntu:/home/john#
The problem is that the rescan of the device may conflict with the device
in being re-initialized, as follows:
- In the rescan we call hisi_sas_slave_alloc() in store_scan() ->
sas_user_scan() -> [__]scsi_scan_target() -> scsi_probe_and_add_lunc()
-> scsi_alloc_sdev() -> hisi_sas_slave_alloc() -> hisi_sas_init_device()
In hisi_sas_init_device() we issue an IT nexus reset for ATA devices
- That IT nexus causes the remote PHY to go down and this triggers a bcast
event
- In parallel libsas processes the bcast event, finds that the phy is down
and marks the device as gone
The hard reset issued in hisi_sas_init_device() is unncessary - as
described in the code comment - so remove it. Also set dev status as
HISI_SAS_DEV_NORMAL as the hisi_sas_init_device() call.
Link: https://lore.kernel.org/r/1652354134-171343-4-git-send-email-john.garry@huawei.com
Fixes: 36c6b7613ef1 ("scsi: hisi_sas: Initialise devices in .slave_alloc callback")
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We have seen errors like this when a SATA device is probed:
[524.566298] hisi_sas_v3_hw 0000L74:02.0: erroneous completion iptt=4096 ...
[524.582827] sas: TMF task open reject failed 500e004aaaaaaaa00
Since commit 21c7e972475e ("scsi: hisi_sas: Disable SATA disk phy for
severe I_T nexus reset failure"), we issue an ATA softreset to disks after
a phy reset to ensure that they are in sound working order. If the
softreset is issued before the remote phy has come back up then the
softreset will fail (errors as above). Remedy this by waiting for the phy
to come back up after the reset.
Link: https://lore.kernel.org/r/1652354134-171343-3-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Create function sas_ata_wait_after_reset() from sas_ata_hard_reset() as
some LLDDs may want to check for a remote ATA phy is up after reset.
Link: https://lore.kernel.org/r/1652354134-171343-2-git-send-email-john.garry@huawei.com
Tested-by: Yihang Li <liyihang6@hisilicon.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update driver version to 42.100.00.00.
Link: https://lore.kernel.org/r/20220511072621.30657-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Terminate string after copying 16 bytes of ChipName data from Manufacturing
Page0 to prevent %s from printing junk characters.
Link: https://lore.kernel.org/r/20220511072621.30657-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
drivers/net/ethernet/mellanox/mlx5/core/main.c
b33886971dbc ("net/mlx5: Initialize flow steering during driver probe")
40379a0084c2 ("net/mlx5_fpga: Drop INNOVA TLS support")
f2b41b32cde8 ("net/mlx5: Remove ipsec_ops function table")
https://lore.kernel.org/all/20220519040345.6yrjromcdistu7vh@sx1/
16d42d313350 ("net/mlx5: Drain fw_reset when removing device")
8324a02c342a ("net/mlx5: Add exit route when waiting for FW")
https://lore.kernel.org/all/20220519114119.060ce014@canb.auug.org.au/
tools/testing/selftests/net/mptcp/mptcp_join.sh
e274f7154008 ("selftests: mptcp: add subflow limits test-cases")
b6e074e171bc ("selftests: mptcp: add infinite map testcase")
5ac1d2d63451 ("selftests: mptcp: Add tests for userspace PM type")
https://lore.kernel.org/all/20220516111918.366d747f@canb.auug.org.au/
net/mptcp/options.c
ba2c89e0ea74 ("mptcp: fix checksum byte order")
1e39e5a32ad7 ("mptcp: infinite mapping sending")
ea66758c1795 ("tcp: allow MPTCP to update the announced window")
https://lore.kernel.org/all/20220519115146.751c3a37@canb.auug.org.au/
net/mptcp/pm.c
95d686517884 ("mptcp: fix subflow accounting on close")
4d25247d3ae4 ("mptcp: bypass in-kernel PM restrictions for non-kernel PMs")
https://lore.kernel.org/all/20220516111435.72f35dca@canb.auug.org.au/
net/mptcp/subflow.c
ae66fb2ba6c3 ("mptcp: Do TCP fallback on early DSS checksum failure")
0348c690ed37 ("mptcp: add the fallback check")
f8d4bcacff3b ("mptcp: infinite mapping receiving")
https://lore.kernel.org/all/20220519115837.380bb8d4@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify scsifront's ring creation and removal via xenbus_setup_ring()
and xenbus_teardown_ring().
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
GRANT_INVALID_REF isn't used in scsifront, so remove it.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Instead of relying on a well behaved PV scsi backend verify all meta
data received from the backend and avoid multiple reads of the same
data from the shared ring page.
In case any illegal data from the backend is detected switch the
PV device to a new "error" state and deactivate it for further use.
Use the "lateeoi" variant for the event channel in order to avoid
event storms blocking the guest.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20220428075323.12853-5-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Add a translation layer for the command result values.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20220428075323.12853-4-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Use kobj_to_dev() instead of open-coding it.
Link: https://lore.kernel.org/r/20220510105113.1351891-1-chi.minghao@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cn>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The bsg_setup_queue() function does not return NULL. It returns error
pointers. Fix the check accordingly.
Link: https://lore.kernel.org/r/YnUf7RQl+A3tigWh@kili
Fixes: 4268fa751365 ("scsi: mpi3mr: Add bsg device support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Using get_cpu() leads to disabling preemption and in this context it is not
possible to acquire the following spinlock_t on PREEMPT_RT because it
becomes a sleeping lock.
Commit 0ea5c27583e1 ("[SCSI] bnx2fc: common free list for cleanup
commands") says that it is using get_cpu() as a fix in case the CPU is
preempted. While this might be true, the important part is that it is now
using the same CPU for locking and unlocking while previously it always
relied on smp_processor_id(). The date structure itself is protected with
a lock so it does not rely on CPU-local access.
Replace get_cpu() with raw_smp_processor_id() to obtain the current CPU
number which is used as an index for the per-CPU resource.
Link: https://lore.kernel.org/r/20220506105758.283887-5-bigeasy@linutronix.de
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The get_cpu() in fc_exch_em_alloc() was introduced in commit f018b73af6db
("[SCSI] libfc, libfcoe, fcoe: use smp_processor_id() only when preempt
disabled") for no other reason than to simply use smp_processor_id()
without getting a warning, because everything is done with the pool->lock
held anyway. However, get_cpu(), by disabling preemption, does not play
well with PREEMPT_RT, particularly when acquiring a regular (and thus
sleepable) spinlock.
Therefore remove the get_cpu() and just use the unstable value as we will
have CPU locality guarantees next by taking the lock. The window of
migration, as noted by Sebastian, is small and even if it happens the
result is correct.
Link: https://lore.kernel.org/r/20211117025956.79616-2-dave@stgolabs.net
Link: https://lore.kernel.org/r/20220506105758.283887-4-bigeasy@linutronix.de
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The per-CPU statistics (struct fc_stats) is updated by getting a stable
per-CPU pointer via get_cpu() + per_cpu_ptr() and then performing the
increment. This can be optimized by using this_cpu_*() which will do
whatever is needed on the architecture to perform the update safe and
efficient. The read out of the individual value (fc_get_host_stats())
should be done by using READ_ONCE() instead of a plain-C access. The
difference is that READ_ONCE() will always perform a single access while
the plain-C access can be split by the compiler into two loads if it
appears beneficial. The usage of u64 has the side-effect that it is also
64bit wide on 32bit architectures and the read is always split into two
loads. The can lead to strange values if the read happens during an update
which alters both 32bit parts of the 64bit value. This can be circumvented
by either using a 32bit variables on 32bit architecures or extending the
statistics with a sequence counter.
Use this_cpu_*() API to update the statistics and READ_ONCE() to read it.
Link: https://lore.kernel.org/r/20220506105758.283887-3-bigeasy@linutronix.de
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
fcoe_get_paged_crc_eof() relies on the caller having preemption disabled to
ensure the per-CPU fcoe_percpu context remains valid throughout the
call. This is done by either holding spinlocks (such as bnx2fc_global_lock
or qedf_global_lock) or the get_cpu() from fcoe_alloc_paged_crc_eof(). This
last one breaks PREEMPT_RT semantics as there can be memory allocation and
end up sleeping in atomic contexts.
Introduce a local_lock_t to struct fcoe_percpu that will keep the non-RT
case the same, mapping to preempt_disable/enable, while RT will use a
per-CPU spinlock allowing the region to be preemptible but still maintain
CPU locality. The other users of fcoe_percpu are already safe in this
regard and do not require local_lock()ing.
Link: https://lore.kernel.org/r/20211117025956.79616-3-dave@stgolabs.net
Link: https://lore.kernel.org/r/20220506105758.283887-2-bigeasy@linutronix.de
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The code for gso_max_size was added originally to allow for debugging and
workaround of buggy devices that couldn't support TSO with blocks 64K in
size. The original reason for limiting it to 64K was because that was the
existing limits of IPv4 and non-jumbogram IPv6 length fields.
With the addition of Big TCP we can remove this limit and allow the value
to potentially go up to UINT_MAX and instead be limited by the tso_max_size
value.
So in order to support this we need to go through and clean up the
remaining users of the gso_max_size value so that the values will cap at
64K for non-TCPv6 flows. In addition we can clean up the GSO_MAX_SIZE value
so that 64K becomes GSO_LEGACY_MAX_SIZE and UINT_MAX will now be the upper
limit for GSO_MAX_SIZE.
v6: (edumazet) fixed a compile error if CONFIG_IPV6=n,
in a new sk_trim_gso_size() helper.
netif_set_tso_max_size() caps the requested TSO size
with GSO_MAX_SIZE.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The storvsc driver has special case code for running on the first released
versions of Hyper-V: 2008 and 2008 R2/Windows 7. These versions are now
out of support (except for extended security updates) and lack support
for performance features like multiple VMbus channels that are needed for
effective production usage of Linux guests.
The negotiation of the VMbus protocol versions required by these old
Hyper-V versions has been removed from the VMbus driver. So now remove
the handling of these VMbus protocol versions from the storvsc driver.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/1651509391-2058-3-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
Complete all new I/O requests issued to an unrecoverable controller with
DID_ERROR status instead of returning the I/O requests with
SCSI_MLQUEUE_HOST_BUSY. This will prevent the infinite retries of the new
I/Os when a controller is in an unrecoverable state.
Link: https://lore.kernel.org/r/20220505184808.24049-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If any drive is missing during reset, the driver checks whether the device
is exposed to the OS. If it is, then it removes the device from the OS and
its own internal list. For hidden devices, even if they are found as
missing during reset, the driver is not removing them from its internal
list.
Modify driver to remove hidden devices from the driver's target device list
if they are missing during soft reset.
Link: https://lore.kernel.org/r/20220505184808.24049-2-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Set each SCSI device's default I/O timeout and default error handling I/O
timeout to 60s.
Link: https://lore.kernel.org/r/20220505184808.24049-3-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Update lpfc version to 14.2.0.3
Link: https://lore.kernel.org/r/20220506035519.50908-13-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
NVMe I/O problems may be seen on IOMMU enabled platforms. Adapter I/Os
failing with transfer length mismatches.
The sg list processing routine for NVMe I/O is accessing the sg entry
directly for the length and address fields. On some IOMMU platforms,
contigous mappings are compressed to the first sg entry with the sum of the
lengths set to the sg entry dma_length field. The length fields are left
for later use by the unmap call. As such, the driver didn't see the actual
dma_length value, just the first entries length value. Drivers are to use
the sg_dma_length() and sg_dma_address() macros to reference the sg
entry. The macros select the proper length field (dma_length or length) to
reference.
Fix the offending code to use the sg_dma_xxx macros.
Link: https://lore.kernel.org/r/20220506035519.50908-12-jsmart2021@gmail.com
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Co-developed-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When configuring CMF management based on signals instead of FPINs, FPIN
alarm and warning statistics are not tracked.
Change the behavior so that FPIN alarms and warnings are always tracked
regardless of the configured mode.
Similar changes are made in the CMF signal stat accounting logic. Upon
receipt of a signal, only track signaled alarms and warnings. FPIN stats
should not be incremented upon receipt of a signal.
Link: https://lore.kernel.org/r/20220506035519.50908-11-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After a link up, it's possible for the switch to change FDMI support (e.g.
FDMI1 vs FDMI2 vs SmartSAN). If the switch reverts to FDMI1, then the
revert is currently not detected.
Additionally, when NPIV is configured, it's possible the physical port's
RHBA is unprocessed by the switch before reciept of an NPIV port issued
RPRT. This causes some switches vendors to reject the NPIV's RPRT.
Fix by reinitializing base FDMI mode on link up, and defer FDMI vport RPRT
submission until after confirming physical port's RHBA is completed.
Link: https://lore.kernel.org/r/20220506035519.50908-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently, VMID registration is configured via module parameters. This
could lead to VMID compatibility issues if two ports are connected to
different brands of switches, as the two brands implement VMID differently.
Make logical changes so that VMID registration is based on common service
parameters from FLOGI_ACC with fabric rather than module parameters.
Link: https://lore.kernel.org/r/20220506035519.50908-9-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During large NPIV port testing, it was sometimes seen that not all vports
would log back in to the target device.
There are instances when the fabric is slow to respond to a spam of GID_PT
requests and as a result the SLI PORT may abort the GID_PT request because
the fabric takes so long. lpfc_cmpl_ct_cmd_gid_pt() would enter the
lpfc_err_lost_link() logic and attempt to lpfc_els_flush_rscn(), which is
fine, but forgets to decrement the gidft_inp counter. This results in a
vport->gidft_inp never reaching 0 and never restarting discovery again.
Decrement vport->gidft_inp if lpfc_err_lost_link() is true for both
lpfc_cmpl_ct_cmd_gid_pt() and lpfc_cmpl_ct_cmd_gid_ft().
Increase logging info during RSCN timeout and lpfc_err_lost_link() events.
Link: https://lore.kernel.org/r/20220506035519.50908-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In GID_PT mode with lpfc_ns_query=1, a race condition between iterating the
vport->fc_nodes list in lpfc_rscn_recovery_check() and cleanup of an ndlp
can trigger a crash while processing the RSCN of another initiator from the
same zone.
During iteration of the vport->fc_nodes list, an ndlp is cleaned up and
released. lpfc_dequeue_node() is called from lpfc_cleanup_node() leading to
a bad ndlp dereference in lpfc_rscn_recovery_check().
Change list_for_each_entry() to list_for_each_entry_safe() in
lpfc_rscn_recovery_check() to protect against removal of an initiator ndlp,
while walking the vport->fc_nodes list.
Link: https://lore.kernel.org/r/20220506035519.50908-7-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Upon driver receipt of a CT cmd for type = 0xFA (Management Server) and
subtype = 0x11 (Fabric Device Management Interface), the driver is
responding with garbage CT cmd data when it should send a properly formed
RJT.
The __lpfc_prep_xmit_seq64_s4() routine was using the wrong buffer for the
reject.
Fix by converting the routine to use the buffer specified in the bde within
the wqe rather than the ill-set bmp element.
Link: https://lore.kernel.org/r/20220506035519.50908-6-jsmart2021@gmail.com
Fixes: 61910d6a5243 ("scsi: lpfc: SLI path split: Refactor CT paths")
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After running a short external loopback test, when the external loopback is
removed and a normal cable inserted that is directly connected to a target
device, the system oops in the llpfc_set_rrq_active() routine.
When the loopback was inserted an FLOGI was transmit. As we're looped back,
we receive the FLOGI request. The FLOGI is ABTS'd as we recognize the same
wppn thus understand it's a loopback. However, as the ABTS sends address
information the port is not set to (fffffe), the ABTS is dropped on the
wire. A short 1 frame loopback test is run and completes before the ABTS
times out. The looback is unplugged and the new cable plugged in, and the
an FLOGI to the new device occurs and completes. Due to a mixup in ref
counting the completion of the new FLOGI releases the fabric ndlp. Then the
original ABTS completes and references the released ndlp generating the
oops.
Correct by no-op'ing the ABTS when in loopback mode (it will be dropped
anyway). Added a flag to track the mode to recognize when it should be
no-op'd.
Link: https://lore.kernel.org/r/20220506035519.50908-5-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
During testing with repeated asynchronous resets of the target, an issue
was found when the driver issues a LOGO to disconnect its login and recover
all exchanges. The LOGO command takes a node reference but neglects to
remove it, keeping the node reference count artifically high.
Add a call to lpfc_nlp_put() to lpfc_nlp_logo_unreg() and move the mempool
free call to the routine exit along with the needed put. This is always
safe as this will not be the last reference removed as lpfc_unreg_rpi()
ensures there is an additional reference on the ndlp.
Link: https://lore.kernel.org/r/20220506035519.50908-4-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Code review, following every lpfc_nlp_get() call vs calls during error
handling, discovered cases of missing put calls.
Correct by adding ndlp kref puts in the respective error paths.
Also added comments to several of the error paths to record relationships
to reference counts.
Link: https://lore.kernel.org/r/20220506035519.50908-3-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The prior commit that moved from iocb elements to explicit wqe elements
missed a name change.
Correct __lpfc_sli_release_iocbq_s4() to reference wqe rather than iocb.
Link: https://lore.kernel.org/r/20220506035519.50908-2-jsmart2021@gmail.com
Fixes: a680a9298e7b ("scsi: lpfc: SLI path split: Refactor lpfc_iocbq")
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ufshpb_resume() is only called when the HPB state is HPB_SUSPEND, so the
check statement for "ufshpb_get_state(hpb) != HPB_PRESENT" is useless.
Link: https://lore.kernel.org/r/20220505134707.35929-7-huobean@gmail.com
Reviewed-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In UFS HPB Spec JESD220-3A,
"5.8. Active and inactive information upon power cycle
...
When the device is powered off by the host, the device may restore L2P map
data upon power up or build from the host's HPB READ command. In case
device powered up and lost HPB information, device can signal to the host
through HPB Sense data, by setting HPB Operation as '2' which will inform
the host that device reset HPB information."
Therefore, for HPB device control mode, if the UFS device is reset via the
RST_N pin, the active region information in the device will be reset. If
the host side receives this notification from the device side, it is
recommended to inactivate all active regions in the host's HPB cache.
Link: https://lore.kernel.org/r/20220505134707.35929-6-huobean@gmail.com
Reviewed-by: Keoseong Park <keosung.park@samsung.com>
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
According to the documentation of the sysfs nodes rb_noti_cnt,
rb_active_cnt and rb_inactive_cnt, these are all related to HPB
recommendation in UPIU response packet. 'rcmd' (recommendation) should be
the correct abbreviation.
Change the sysfs documentation about these sysfs nodes to highlight what
they mean under different HPB control modes.
Link: https://lore.kernel.org/r/20220505134707.35929-5-huobean@gmail.com
Reviewed-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
"When the device is powered off by the host, the device may restore L2P map
data upon power up or build from the host's HPB READ command. In case
device powered up and lost HPB information, device can signal to the host
through HPB Sense data, by setting HPB Operation as '2' which will inform
the host that device reset HPB information."
Clean up the handler and make the intent of this handler more readable, no
functional change.
Link: https://lore.kernel.org/r/20220505134707.35929-4-huobean@gmail.com
Reviewed-by: Keoseong Park <keosung.park@samsung.com>
Reviewed-by: Daejun Park <daejun7.park@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If the first enumerator has no initializer, the value of the corresponding
constant is zero.
Link: https://lore.kernel.org/r/20220505134707.35929-3-huobean@gmail.com
Reviewed-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no functional change in this patch, just merge ufshpb_reset() and
ufshpb_reset_host() into one function ufshpb_toggle_state().
Link: https://lore.kernel.org/r/20220505134707.35929-2-huobean@gmail.com
Reviewed-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In order to allow the block devices to enter autosuspend mode during
runtime, thereby allowing the ufshcd host driver to also runtime suspend,
let's make use of the RPM_AUTOSUSPEND flag.
Without this flag, userspace needs to enable the autosuspend feature of
the block devices through sysfs.
Link: https://lore.kernel.org/r/20220504084212.11605-6-manivannan.sadhasivam@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The wmb() inside ufshcd_send_command() is added to make sure that the
doorbell is committed immediately. This leads to couple of expectations:
1. The doorbell write should complete before the function return.
2. The doorbell write should not cross the function boundary.
2nd expectation is fullfilled by the Linux memory model as there is a
guarantee that the critical section won't cross the unlock (release)
operation.
1st expectation is not really needed here as there is no following read/
write that depends on the doorbell to be complete implicitly. Even if the
doorbell write is in a CPUs Write Buffer (WB), wmb() won't flush it. And
there is no real need of a WB flush here as well.
So let's get rid of the wmb() that seems redundant.
Link: https://lore.kernel.org/r/20220504084212.11605-5-manivannan.sadhasivam@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In ufs_qcom_dev_ref_clk_ctrl(), it was noted that the ref_clk needs to be
stable for at least 1us. Even though there is wmb() to make sure the write
gets "completed", there is no guarantee that the write actually reached the
UFS device. There is a good chance that the write could be stored in a
Write Buffer (WB). In that case, even though the CPU waits for 1us, the
ref_clk might not be stable for that period.
So lets do a readl() to make sure that the previous write has reached the
UFS device before udelay().
Also, the wmb() after writel_relaxed() is not really needed. Both writel()
and readl() are ordered on all architectures and the CPU won't speculate
instructions after readl() due to the in-built control dependency with read
value on weakly ordered architectures. So it can be safely removed.
Link: https://lore.kernel.org/r/20220504084212.11605-4-manivannan.sadhasivam@linaro.org
Fixes: f06fcc7155dc ("scsi: ufs-qcom: add QUniPro hardware support and power optimizations")
Cc: stable@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
