| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Avoid using a mixture of tabs and spaces within tables to make them
easier to read and more consistently formatted.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Extend the Tegra194 IO pad table with additional information such as pin
names and 1.8/3.3 V settings to allow a table of voltage control pins to
generated from it. This is similar to what's done for older chips and is
needed to support high-speed modes for SDHCI where switching the pins to
1.8V or 3.3V is necessary.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra PMC has blink control to output 32 kHz clock out to Tegra blink
pin. Blink pad DPD state and enable controls are part of Tegra PMC
register space.
Currently Tegra clock driver registers blink control by passing PMC
address and register offset to clk_register_gate which performs direct
PMC access during clk_ops and with this when PMC is in secure mode, any
access from non-secure world does not go through.
This patch adds blink control registration to the Tegra PMC driver using
PMC specific clock gate operations that use tegra_pmc_readl() and
tegra_pmc_writel() to support both secure mode and non-secure
mode PMC register access.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra PMC has clk_out_1, clk_out_2, and clk_out_3 clocks and currently
these PMC clocks are registered by Tegra clock driver with each clock as
separate mux and gate clocks using clk_register_mux and clk_register_gate
by passing PMC base address and register offsets and PMC programming for
these clocks happens through direct PMC access by the clock driver.
With this, when PMC is in secure mode any direct PMC access from the
non-secure world does not go through and these clocks will not be
functional.
This patch adds these PMC clocks registration to pmc driver with PMC as
a clock provider and registers each clock as single clock.
clk_ops callback implementations for these clocks uses tegra_pmc_readl and
tegra_pmc_writel which supports PMC programming in both secure mode and
non-secure mode.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Tegra194 supports the same reset levels as Tegra186 but extends the set
of reset sources. Provide custom PMC register definitions to account for
the larger field for the reset sources as well as the updated list of
reset sources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v2:
- use the new Tegra194 register definitions
|
|
Reuse the IRQ callbacks from Tegra186 on Tegra194. This fixes failures
to request interrupts on Tegra194 due to the missing callbacks.
Cc: Sowjanya Komatineni <skomatineni@nvidia.com>
Fixes: aba19827fced ("soc/tegra: pmc: Support wake events on more Tegra SoCs")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The remainder of the file uses lower-case for hexadecimal literals, so
change the only odd-one-out occurrence for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The removed barrier isn't needed because writes/reads are strictly ordered
and even if PMC had separate ports for writes, it wouldn't matter since
the hardware logic takes into effect after triggering CPU's power-gating
and at that point all CPU accesses are guaranteed to be completed. That
barrier was copied from the old arch/ code during transition to the soc/
PMC driver and even that the code structure was different back then, the
barrier didn't have a real useful purpose from the start. Lastly, the
tegra_pmc_writel() naturally inserts wmb() because it uses writel(),
and thus this change doesn't actually make any difference in terms of
interacting with hardware. Hence let's remove the barrier to clean up
code a tad.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
It is possible to get a lockup if kernel decides to enter LP2 cpuidle
from some clk-notifier, in that case CCF's "prepare" mutex is kept locked
and thus clk_get_rate(pclk) blocks on the same mutex with interrupts being
disabled, hanging machine.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra210 and prior Tegra chips have deep sleep entry and wakeup related
timings which are platform specific that should be configured before
entering into deep sleep.
Below are the timing specific configurations for deep sleep entry and
wakeup.
- Core rail power-on stabilization timer
- OSC clock stabilization timer after SOC rail power is stabilized.
- Core power off time is the minimum wake delay to keep the system
in deep sleep state irrespective of any quick wake event.
These values depends on the discharge time of regulators and turn OFF
time of the PMIC to allow the complete system to finish entering into
deep sleep state.
These values vary based on the platform design and are specified
through the device tree.
This patch has implementation to configure these timings which are must
to have for proper deep sleep and wakeup operations.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch configures polarity of the core power request signal
in PMC control register based on the device tree property.
PMC asserts and de-asserts power request signal based on it polarity
when it need to power-up and power-down the core rail during SC7.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch implements PMC wakeup sequence for Tegra210 and defines the
commonly used RTC alarm wake event.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch allows to create separate irq_set_wake and irq_set_type
implementations for different Tegra designs PMC that has different
wake models which require difference wake registers and different
programming sequence.
AOWAKE model support is available for Tegra186 and Tegra194 only
and it resides within PMC and supports tiered wake architecture.
Tegra210 and prior Tegra designs uses PMC directly to receive wake
events and coordinate the wake sequence.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Interrupts that don't have an associated wake event or GPIO wake events
end up with an associate IRQ chip that is NULL and which causes IRQ code
to crash. This is because we don't implicitly set the parent IRQ chip by
allocating the interrupt at the parent. However, there really isn't a
corresponding interrupt at the parent, so we need to work around this by
setting the special no_irq_chip as the IRQ chip for these interrupts.
Fixes: 19906e6b1667 ("soc/tegra: pmc: Add wake event support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration changes:
- Evaluate PCI Boot Configuration _DSM to learn if firmware wants us
to preserve its resource assignments (Benjamin Herrenschmidt)
- Simplify resource distribution (Nicholas Johnson)
- Decode 32 GT/s link speed (Gustavo Pimentel)
Virtualization:
- Fix incorrect caching of VF config space size (Alex Williamson)
- Fix VF driver probing sysfs knobs (Alex Williamson)
Peer-to-peer DMA:
- Fix dma_virt_ops check (Logan Gunthorpe)
Altera host bridge driver:
- Allow building as module (Ley Foon Tan)
Armada 8K host bridge driver:
- add PHYs support (Miquel Raynal)
DesignWare host bridge driver:
- Export APIs to support removable loadable module (Vidya Sagar)
- Enable Relaxed Ordering erratum workaround only on Tegra20 &
Tegra30 (Vidya Sagar)
Hyper-V host bridge driver:
- Fix use-after-free in eject (Dexuan Cui)
Mobiveil host bridge driver:
- Clean up and fix many issues, including non-identify mapped
windows, 64-bit windows, multi-MSI, class code, INTx clearing (Hou
Zhiqiang)
Qualcomm host bridge driver:
- Use clk bulk API for 2.4.0 controllers (Bjorn Andersson)
- Add QCS404 support (Bjorn Andersson)
- Assert PERST for at least 100ms (Niklas Cassel)
R-Car host bridge driver:
- Add r8a774a1 DT support (Biju Das)
Tegra host bridge driver:
- Add support for Gen2, opportunistic UpdateFC and ACK (PCIe protocol
details) AER, GPIO-based PERST# (Manikanta Maddireddy)
- Fix many issues, including power-on failure cases, interrupt
masking in suspend, UPHY settings, AFI dynamic clock gating,
pending DLL transactions (Manikanta Maddireddy)
Xilinx host bridge driver:
- Fix NWL Multi-MSI programming (Bharat Kumar Gogada)
Endpoint support:
- Fix 64bit BAR support (Alan Mikhak)
- Fix pcitest build issues (Alan Mikhak, Andy Shevchenko)
Bug fixes:
- Fix NVIDIA GPU multi-function power dependencies (Abhishek Sahu)
- Fix NVIDIA GPU HDA enablement issue (Lukas Wunner)
- Ignore lockdep for sysfs "remove" (Marek Vasut)
Misc:
- Convert docs to reST (Changbin Du, Mauro Carvalho Chehab)"
* tag 'pci-v5.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (107 commits)
PCI: Enable NVIDIA HDA controllers
tools: PCI: Fix installation when `make tools/pci_install`
PCI: dwc: pci-dra7xx: Fix compilation when !CONFIG_GPIOLIB
PCI: Fix typos and whitespace errors
PCI: mobiveil: Fix INTx interrupt clearing in mobiveil_pcie_isr()
PCI: mobiveil: Fix infinite-loop in the INTx handling function
PCI: mobiveil: Move PCIe PIO enablement out of inbound window routine
PCI: mobiveil: Add upper 32-bit PCI base address setup in inbound window
PCI: mobiveil: Add upper 32-bit CPU base address setup in outbound window
PCI: mobiveil: Mask out hardcoded bits in inbound/outbound windows setup
PCI: mobiveil: Clear the control fields before updating it
PCI: mobiveil: Add configured inbound windows counter
PCI: mobiveil: Fix the valid check for inbound and outbound windows
PCI: mobiveil: Clean-up program_{ib/ob}_windows()
PCI: mobiveil: Remove an unnecessary return value check
PCI: mobiveil: Fix error return values
PCI: mobiveil: Refactor the MEM/IO outbound window initialization
PCI: mobiveil: Make some register updates more readable
PCI: mobiveil: Reformat the code for readability
dt-bindings: PCI: mobiveil: Change gpio_slave and apb_csr to optional
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc: tegra: Changes for v5.3-rc1
This contains a set of minor fixes and cleanups for core Tegra drivers.
* tag 'tegra-for-5.3-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: Select pinctrl for Tegra194
soc/tegra: fuse: Do not log error message on deferred probe
soc/tegra: pmc: Add comments clarifying wake events
soc/tegra: pmc: Avoid crash for non-wake IRQs
soc/tegra: pmc: Fail to allocate more than one wake IRQ
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
tegra_powergate_sequence_power_up() powers up partition and also enables
clock & reset. However, if a controller like PCIe have multiple clocks
& resets and they need to be enabled in a sequence, driver must use
standalone function tegra_powergate_power_on() to power up partition.
Export tegra_powergate_power_on() to allow Tegra controller drivers to
unpower gate partition independent to clock & reset.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add some comments to clarify the purpose of the wake event support
implemented in the PMC driver.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
For interrupts that are not wakeup sources but that may end up getting
mapped through the PMC as interrupt parent (this can happen for GPIOs),
return early in order to avoid a subsequent crash from an out-of-bounds
access to the register region.
Reported-by: Bitan Biswas <bbiswas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The code currently doesn't support allocating more than one wake IRQ at
a time. Detect this situation and error out. Also make sure to output a
warning when that happens to help track down callers.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Commit 8df127456f29 ("soc/tegra: pmc: Enable XUSB partitions on boot")
was added as a workaround to ensure that the XUSB powergates or domains
were turned on early during boot because as this time the Tegra XHCI
driver did not handle the power domains at all. Now that the Tegra XHCI
driver has been updated to properly managed the power domains, the
workaround to enable the XUSB power domain early has been removed. This
also means that we can now move the initialisation of the powergates
into the PMC driver probe. Therefore, move the powergate initialisation
into the PMC driver probe and return any errors detected. To handle any
errors, functions to cleanup and remove any power-domains registered
with the generic power-domain framework have been added.
Finally the initialisation of the 'powergates_available' bitmask is kept
in the PMC early init function to allow the legacy PMC powergate APIs to
be called during early boot for enabling secondary CPUs on 32-bit Tegra
devices.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Commit 5f84bb1a4099 ("soc/tegra: pmc: Add sysfs entries for reset info")
added sysfs entries for Tegra reset source and level. However, these
sysfs are not removed on error and so if the registering of PMC device
is probe deferred, then the next time we attempt to probe the PMC device
warnings such as the following will be displayed on boot ...
sysfs: cannot create duplicate filename '/devices/platform/7000e400.pmc/reset_reason'
Fix this by calling device_remove_file() for each sysfs entry added on
failure. Note that we call device_remove_file() unconditionally without
checking if the sysfs entry was created in the first place, but this
should be OK because kernfs_remove_by_name_ns() will fail silently.
Fixes: 5f84bb1a4099 ("soc/tegra: pmc: Add sysfs entries for reset info")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Commit 5f84bb1a4099 ("soc/tegra: pmc: Add sysfs entries for reset info")
added support for reading the Tegra reset source and level from sysfs.
However, there are a few issues with this commit which are ...
1. The number of reset sources for Tegra210 is defined as 5 but it
should be 6.
2. The number of reset sources for Tegra186 is defined as 13 but it
should be 15.
3. The SoC data variables num_reset_sources and num_reset_levels are
defined but never used.
Fix the above by ...
1. Removing the reset source 'AOTAG' from the tegra30_reset_sources
because this is only applicable for Tegra210.
2. Adding a new tegra210_reset_sources structure for Tegra210 reset
sources.
3. Correct the number of reset sources for Tegra210 and Tegra186 by
using the ARRAY_SIZE macro.
4. Updating the functions reset_reason_show() and reset_level_show()
to check whether the value read is valid. While we are at it
clean-up these functions to remove an unnecessary u32 variable.
Fixes: 5f84bb1a4099 ("soc/tegra: pmc: Add sysfs entries for reset info")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
By implementing the acquire/release protocol, the resets can be shared
with other drivers that also adhere to this protocol. This will be used
for example by the SOR driver to put hardware into a known good state,
irrespective of whether or not the power domain can be reset.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
On Tegra210 systems with new enough boot software, direct register
accesses to PMC register space from the non-secure world are not
allowed. Instead a monitor call may be used to read and write PMC
registers.
Add code to detect such a system by attempting to write a scratch
register and detecting if the write happened or not. If not, we switch
to doing all register accesses through the monitor call.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
|
|
It's not strictly necessary to initialize the fields in struct
tegra_pmc_soc if they are 0/false. However, we already initialize them
explicitly even if unnecessary, so keep doing that for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
|
|
Some recently added code used weird alignment and indentation. Fix these
occurrences to make them consistent with the rest of the code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
|
|
Instead of using the global pmc variable, pass around a pointer where
possible. Also, replace most occurrences of pr_*() functions by their
equivalent dev_*() functions, reusing the pmc->dev pointer.
It's not possible to get completely rid of the global variable because
some of the public API that this driver exposes still relies on it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
|
|
Now there are no more external users of tegra_powergate_is_powered(),
make this a local function.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Some of the fields in struct tegra_pmc had not been documented when they
were added. Add the missing kerneldoc.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
|
|
This will make it easier to insert new includes in the right place in
subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
|
|
The new prefix allows the GPIOs to be uniquely identified on a per-chip
basis, which makes it easier to distinguish Tegra186 specific GPIOs from
those of later chips such as Tegra194 which supports a very different
set of GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64
C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in
GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
and misc cleanups across several platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: at91: add support in soc driver for new SAM9X60
ARM: at91: add support in soc driver for LPDDR2 SiP
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: renesas: rcar-sysc: Fix power domain control after system resume
soc: renesas: rcar-sysc: Merge PM Domain registration and linking
soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers
soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B}
dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1
dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1
dt-bindings: sram: Add Allwinner suniv F1C100s
soc: sunxi: sram: Add support for the H5 SoC system control
soc: sunxi: sram: Enable EMAC clock access for H3 variant
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
dmaengine: pxa: make the filter function internal
...
|
|
When CONFIG_SMP is disabled, the tegra clk driver now fails to build:
drivers/clk/tegra/clk-tegra30.c: In function ‘tegra30_cpu_rail_off_ready’:
drivers/clk/tegra/clk-tegra30.c:1151:2: error: implicit declaration of function ‘tegra_pmc_cpu_is_powered’ [-Werror=implicit-function-declaration]
cpu_pwr_status = tegra_pmc_cpu_is_powered(1) ||
^
Fix the above error by removing the CONFIG_SMP ifdef around the
declaration around the PMC CPU APIs because although these are not
needed for non-SMP configurations, there is no harm in including these
for non-SMP builds either.
Fixes: 61866523ed6e ("clk: tegra30: Use Tegra CPU powergate helper function")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Tegra194 supports 96 wake events in total. Many of them are never used,
so only the most common ones (RTC alarm and power key) are currently
defined.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra186 support 96 wake events in total. Many of them are never used,
so only the most common ones (RTC alarm and power key) are currently
defined.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The power management controller has top-level controls that allow
certain interrupts (such as from the RTC or a subset of GPIOs) to
wake the system from sleep. Implement infrastructure to support
these wake events.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The PMC controller on Tegra194 has a couple of new I/O pads and drops
others compared to Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This fixes splats like the one below if CONFIG_DEBUG_ATOMIC_SLEEP=y
and machine (Tegra30) booted with SMP=n or all secondary CPU's are put
offline. Locking isn't needed because it protects atomic operation.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G C 4.18.0-next-20180821-00180-gc3ebb6544e44-dirty #823
Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[<c01134f4>] (unwind_backtrace) from [<c010db2c>] (show_stack+0x20/0x24)
[<c010db2c>] (show_stack) from [<c0bd0f3c>] (dump_stack+0x94/0xa8)
[<c0bd0f3c>] (dump_stack) from [<c0151df8>] (___might_sleep+0x13c/0x174)
[<c0151df8>] (___might_sleep) from [<c0151ea0>] (__might_sleep+0x70/0xa8)
[<c0151ea0>] (__might_sleep) from [<c0bec2b8>] (mutex_lock+0x2c/0x70)
[<c0bec2b8>] (mutex_lock) from [<c0589844>] (tegra_powergate_is_powered+0x44/0xa8)
[<c0589844>] (tegra_powergate_is_powered) from [<c0581a60>] (tegra30_cpu_rail_off_ready+0x30/0x74)
[<c0581a60>] (tegra30_cpu_rail_off_ready) from [<c0122244>] (tegra30_idle_lp2+0xa0/0x108)
[<c0122244>] (tegra30_idle_lp2) from [<c0853438>] (cpuidle_enter_state+0x140/0x540)
[<c0853438>] (cpuidle_enter_state) from [<c08538a4>] (cpuidle_enter+0x40/0x4c)
[<c08538a4>] (cpuidle_enter) from [<c01595e0>] (call_cpuidle+0x30/0x48)
[<c01595e0>] (call_cpuidle) from [<c01599f8>] (do_idle+0x238/0x28c)
[<c01599f8>] (do_idle) from [<c0159d28>] (cpu_startup_entry+0x28/0x2c)
[<c0159d28>] (cpu_startup_entry) from [<c0be76c8>] (rest_init+0xd8/0xdc)
[<c0be76c8>] (rest_init) from [<c1200f50>] (start_kernel+0x41c/0x430)
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Implement read-only reset_reason and reset_level sysfs attributes that
can be used to query the reset reason and level at runtime.
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Now that the Tegra xHCI driver manages the XUSB power-domains itself,
remove the code to power-up the power-domains used by the xHCI device
from the PMC driver on boot.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
|
|
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Li Yang <leoyang.li@nxp.com>
Cc: David Brown <david.brown@linaro.org>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-soc@vger.kernel.org
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Qiang Zhao <qiang.zhao@nxp.com>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Register a pinctrl device and implement get and set functions for
PIN_CONFIG_LOW_POWER_MODE and PIN_CONFIG_POWER_SOURCE parameters.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Make tegra_io_pad_set_voltage() and tegra_io_pad_get_voltage() static
and remove the prototypes from pmc.h. Remove enum tegra_io_pad_voltage
and use the defines from <dt-bindings/pinctrl/pinctrl-tegra-io-pad.h>
instead.
These functions aren't used outside of the pmc driver and new use cases
should use the pinctrl interface instead.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Refactor the IO pad tables into macro tables so that they can be reused
to generate pinctrl pin descriptors. Also add a name field which is
needed by pinctrl.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
