| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"One small core feature this time around but mostly driver improvements
and additions for SPI:
- Add support for controlling the idle state of MOSI, some systems
can support this and depending on the system integration may need
it to avoid glitching in some situations
- Support for polling mode in the S3C64xx driver and DMA on the
Qualcomm QSPI driver
- Support for several Allwinner SoCs, AMD Pensando Elba, Intel Mount
Evans, Renesas RZ/V2M, and ST STM32H7"
* tag 'spi-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
spi: dt-bindings: atmel,at91rm9200-spi: fix broken sam9x7 compatible
spi: dt-bindings: atmel,at91rm9200-spi: add sam9x7 compatible
spi: Add support for Renesas CSI
spi: dt-bindings: Add bindings for RZ/V2M CSI
spi: sun6i: Use the new helper to derive the xfer timeout value
spi: atmel: Prevent false timeouts on long transfers
spi: dt-bindings: stm32: do not disable spi-slave property for stm32f4-f7
spi: Create a helper to derive adaptive timeouts
spi: spi-geni-qcom: correctly handle -EPROBE_DEFER from dma_request_chan()
spi: stm32: disable spi-slave property for stm32f4-f7
spi: stm32: introduction of stm32h7 SPI device mode support
spi: stm32: use dmaengine_terminate_{a}sync instead of _all
spi: stm32: renaming of spi_master into spi_controller
spi: dw: Remove misleading comment for Mount Evans SoC
spi: dt-bindings: snps,dw-apb-ssi: Add compatible for Intel Mount Evans SoC
spi: dw: Add compatible for Intel Mount Evans SoC
spi: s3c64xx: Use dev_err_probe()
spi: s3c64xx: Use the managed spi master allocation function
spi: spl022: Probe defer is no error
spi: spi-imx: fix mixing of native and gpio chipselects for imx51/imx53/imx6 variants
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This release is almost all drivers, there's some small improvements in
the core but otherwise everything is updates to drivers, mostly the
addition of new ones.
There's also a bunch of changes pulled in from the MFD subsystem as
dependencies, Rockchip and TI core MFD code that the regulator drivers
depend on.
I've also yet again managed to put a SPI commit in the regulator tree,
I don't know what it is about those two trees (this for
spi-geni-qcom).
Summary:
- Support for Renesas RAA215300, Rockchip RK808, Texas Instruments
TPS6594 and TPS6287x, and X-Powers AXP15060 and AXP313a"
* tag 'regulator-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (43 commits)
regulator: Add Renesas PMIC RAA215300 driver
regulator: dt-bindings: Add Renesas RAA215300 PMIC bindings
regulator: ltc3676: Use maple tree register cache
regulator: ltc3589: Use maple tree register cache
regulator: helper: Document ramp_delay parameter of regulator_set_ramp_delay_regmap()
regulator: mt6358: Use linear voltage helpers for single range regulators
regulator: mt6358: Const-ify mt6358_regulator_info data structures
regulator: mt6358: Drop *_SSHUB regulators
regulator: mt6358: Merge VCN33_* regulators
regulator: dt-bindings: mt6358: Drop *_sshub regulators
regulator: dt-bindings: mt6358: Merge ldo_vcn33_* regulators
regulator: dt-bindings: pwm-regulator: Add missing type for "pwm-dutycycle-unit"
regulator: Switch two more i2c drivers back to use .probe()
spi: spi-geni-qcom: Do not do DMA map/unmap inside driver, use framework instead
soc: qcom: geni-se: Add interfaces geni_se_tx_init_dma() and geni_se_rx_init_dma()
regulator: tps6594-regulator: Add driver for TI TPS6594 regulators
regulator: axp20x: Add AXP15060 support
regulator: axp20x: Add support for AXP313a variant
dt-bindings: pfuze100.yaml: Add an entry for interrupts
regulator: stm32-pwr: Fix regulator disabling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
- Yosry Ahmed brought back some cgroup v1 stats in OOM logs
- Yosry has also eliminated cgroup's atomic rstat flushing
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning
- Lorenzo Stoakes has done some maintanance work on the
get_user_pages() interface
- Liam Howlett continues with cleanups and maintenance work to the
maple tree code. Peng Zhang also does some work on maple tree
- Johannes Weiner has done some cleanup work on the compaction code
- David Hildenbrand has contributed additional selftests for
get_user_pages()
- Thomas Gleixner has contributed some maintenance and optimization
work for the vmalloc code
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting
- Christoph Hellwig has some cleanups for the filemap/directio code
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the
provided APIs rather than open-coding accesses
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings
- John Hubbard has a series of fixes to the MM selftesting code
- ZhangPeng continues the folio conversion campaign
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment
from 128 to 8
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code
- Vishal Moola also has done some folio conversion work
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch
* tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (380 commits)
mm/hugetlb: remove hugetlb_set_page_subpool()
mm: nommu: correct the range of mmap_sem_read_lock in task_mem()
hugetlb: revert use of page_cache_next_miss()
Revert "page cache: fix page_cache_next/prev_miss off by one"
mm/vmscan: fix root proactive reclaim unthrottling unbalanced node
mm: memcg: rename and document global_reclaim()
mm: kill [add|del]_page_to_lru_list()
mm: compaction: convert to use a folio in isolate_migratepages_block()
mm: zswap: fix double invalidate with exclusive loads
mm: remove unnecessary pagevec includes
mm: remove references to pagevec
mm: rename invalidate_mapping_pagevec to mapping_try_invalidate
mm: remove struct pagevec
net: convert sunrpc from pagevec to folio_batch
i915: convert i915_gpu_error to use a folio_batch
pagevec: rename fbatch_count()
mm: remove check_move_unevictable_pages()
drm: convert drm_gem_put_pages() to use a folio_batch
i915: convert shmem_sg_free_table() to use a folio_batch
scatterlist: add sg_set_folio()
...
|
|
Merge series from Biju Das <biju.das.jz@bp.renesas.com>:
This patch series aims to add support for Renesas PMIC RAA215300 and
built-in RTC found on this PMIC device.
The details of PMIC can be found here[1].
Renesas PMIC RAA215300 exposes two separate i2c devices, one for the main
device and another for rtc device.
|
|
The RZ/V2M SoC comes with the Clocked Serial Interface (CSI)
IP, which is a master/slave SPI controller.
This commit adds a driver to support CSI master mode.
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622113341.657842-4-fabrizio.castro.jz@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:
I recently came across an issue with the Atmel spi controller driver
which would stop my transfers after a too small timeout when performing
big transfers (reading a 4MiB flash in one transfer). My initial idea
was to derive a the maximum amount of time a transfer would take
depending on its size and use that as value to avoid erroring-out when
not relevant. Mark wanted to go further by creating a core helper doing
that, based on the heuristics from the sun6i driver.
Here is a small series of 3 patches doing exactly that.
|
|
A helper was recently added to the core to factorize common code between
drivers, like the amount of time a driver should wait for a transfer to
happen.
It is of course possible to use a default value (like eg. 1s) but it is
way stronger to adapt this amount of time to the transfer. Indeed, long
transfers (eg. 4MiB) on a slow single-spi bus might take more than the
usual second of timeout and prevent lengthy transfers.
The core helper was heavily inspired by the logic applied in this
driver, the only difference being the minimum amount of time which was
enlarged from 0.1s to 0.5s.
Use this helper instead of open-coding it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jernej Škrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-4-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A slow SPI bus clocks at ~20MHz, which means it would transfer about
2500 bytes per second with a single data line. Big transfers, like when
dealing with flashes can easily reach a few MiB. The current DMA timeout
is set to 1 second, which means any working transfer of about 4MiB will
always be cancelled.
With the above derivations, on a slow bus, we can assume every byte will
take at most 0.4ms. Said otherwise, we could add 4ms to the 1-second
timeout delay every 10kiB. On a 4MiB transfer, it would bring the
timeout delay up to 2.6s which still seems rather acceptable for a
timeout.
The consequence of this is that long transfers might be allowed, which
hence requires the need to interrupt the transfer if wanted by the
user. We can hence switch to the _interruptible variant of
wait_for_completion. This leads to a little bit more handling to also
handle the interrupted case but looks really acceptable overall.
While at it, we drop the useless, noisy and redundant WARN_ON() call.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ryan Wanner <ryan.wanner@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-3-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ARCH_DMA_MINALIGN represents the minimum (static) alignment for safe DMA
operations while ARCH_KMALLOC_MINALIGN is the minimum kmalloc() objects
alignment.
Link: https://lkml.kernel.org/r/20230612153201.554742-9-catalin.marinas@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
Tested-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mike Snitzer <snitzer@kernel.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Now spi_geni_grab_gpi_chan() errors are correctly reported, the
-EPROBE_DEFER error should be returned from probe in case the
GPI dma driver is built as module and/or not probed yet.
Fixes: b59c122484ec ("spi: spi-geni-qcom: Add support for GPI dma")
Fixes: 6532582c353f ("spi: spi-geni-qcom: fix error handling in spi_geni_grab_gpi_chan()")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230615-topic-sm8550-upstream-fix-spi-geni-qcom-probe-v2-1-670c3d9e8c9c@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now spi_geni_grab_gpi_chan() errors are correctly reported, the
-EPROBE_DEFER error should be returned from probe in case the
GPI dma driver is built as module and/or not probed yet.
Fixes: b59c122484ec ("spi: spi-geni-qcom: Add support for GPI dma")
Fixes: 6532582c353f ("spi: spi-geni-qcom: fix error handling in spi_geni_grab_gpi_chan()")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230615-topic-sm8550-upstream-fix-spi-geni-qcom-probe-v2-1-670c3d9e8c9c@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for stm32h7 to use SPI controller in device role.
In such case, the spi instance should have the spi-slave property
defined.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230615075815.310261-5-valentin.caron@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Avoid usage of deprecated dmaengine_terminate_all and use
dmaengine_terminate_sync and dmaengine_terminate_async instead.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230615075815.310261-3-valentin.caron@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Preparing introduction of SPI device, rename the spi_master structure
into spi_controller. This doesn't have any functional impact since
spi_master was already a macro for spi_controller.
Referring now to ctrl instead of master since the spi_controller
structure might not be used as a master controller only.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230615075815.310261-2-valentin.caron@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 445164e8c136 ("spi: dw: Replace spi->chip_select references with
function calls") replaced direct access to spi.chip_select with
spi_*_chipselect calls but incorrectly replaced a set instance with a
get instance, replace the incorrect instance.
Fixes: 445164e8c136 ("spi: dw: Replace spi->chip_select references with function calls")
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230613162103.569812-1-abe.kohandel@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Andi Shyti <andi.shyti@kernel.org>:
Two small cleanups in the probe function. The first puts in use
the managed spi master allocation while the second implements the
dev_err_probe() function.
|
|
Remove a misleading comment about the DMA operations of the Intel Mount
Evans SoC's SPI Controller as requested by Serge.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Link: https://lore.kernel.org/linux-spi/20230606191333.247ucbf7h3tlooxf@mobilestation/
Fixes: 0760d5d0e9f0 ("spi: dw: Add compatible for Intel Mount Evans SoC")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230606231844.726272-1-abe.kohandel@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The spi geni driver in SE DMA mode, unlike GSI DMA, is not making use of
DMA mapping functionality available in the framework.
The driver does mapping internally which makes dma buffer fields available
in spi_transfer struct superfluous while requiring additional members in
spi_geni_master struct.
Conform to the design by having framework handle map/unmap and do only
DMA transfer in the driver; this also simplifies code a bit.
Fixes: e5f0dfa78ac7 ("spi: spi-geni-qcom: Add support for SE DMA mode")
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/1684325894-30252-3-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DSPI controller has configurable timing for
(a) tCSC: the interval between the assertion of the chip select and the
first clock edge
(b) tASC: the interval between the last clock edge and the deassertion
of the chip select
What is a bit surprising, but is documented in the figure "Example of
continuous transfer (CPHA=1, CONT=1)" in the datasheet, is that when the
chip select stays asserted between multiple TX FIFO writes, the tCSC and
tASC times still apply. With CONT=1, chip select remains asserted, but
SCK takes a break and goes to the idle state for tASC + tCSC ns.
In other words, the default values (of 0 and 0 ns) result in SCK
glitches where the SCK transition to the idle state, as well as the SCK
transition from the idle state, will have no delay in between, and it
may appear that a SCK cycle has simply gone missing. The resulting
timing violation might cause data corruption in many peripherals, as
their chip select is asserted.
The driver has device tree bindings for tCSC ("fsl,spi-cs-sck-delay")
and tASC ("fsl,spi-sck-cs-delay"), but these are only specified to apply
when the chip select toggles in the first place, and this timing
characteristic depends on each peripheral. Many peripherals do not have
explicit timing requirements, so many device trees do not have these
properties present at all.
Nonetheless, the lack of SCK glitches is a common sense requirement, and
since the SCK stays in the idle state during transfers for tCSC+tASC ns,
and that in itself should look like half a cycle, then let's ensure that
tCSC and tASC are at least a quarter of a SCK period, such that their
sum is at least half of one.
Fixes: 95bf15f38641 ("spi: fsl-dspi: Add ~50ns delay between cs and sck")
Reported-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Debugged-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Tested-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230529223402.1199503-1-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Intel Mount Evans SoC's Integrated Management Complex uses the SPI
controller for access to a NOR SPI FLASH. However, the SoC doesn't
provide a mechanism to override the native chip select signal.
This driver doesn't use DMA for memory operations when a chip select
override is not provided due to the native chip select timing behavior.
As a result no DMA configuration is done for the controller and this
configuration is not tested.
The controller also has an errata where a full TX FIFO can result in
data corruption. The suggested workaround is to never completely fill
the FIFO. The TX FIFO has a size of 32 so the fifo_len is set to 31.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230606145402.474866-2-abe.kohandel@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Simplify the code by using dev_err_probe() instead of dev_err()
and 'return'.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230606012051.2139333-3-andi.shyti@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use devm_spi_alloc_master() and get rid of one goto error path
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230606012051.2139333-2-andi.shyti@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add check for dma_set_mask() and return the error if it fails.
Fixes: 1a6f854f7daa ("spi: cadence-quadspi: Add Xilinx Versal external DMA support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20230606093859.27818-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the spi controller is registered and the cs_gpiods cannot be
assigned, causing a defer of the probe, there is an error print saying:
"probe - problem registering spi master"
This should not be announced as an error. Print this message for all
errors except for the probe defer.
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20230602-pl022-defer-fix-v2-1-383f6bc2293a@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
variants
Commit 87c614175bbf (spi: spi-imx: fix MX51_ECSPI_* macros when cs >
3) ensured that the argument passed to the macros was masked with &3,
so that we no longer write outside the intended fields in the various
control registers. When all chip selects are gpios, this works just
fine.
However, when a mix of native and gpio chip selects are in use, that
masking is too naive. Say, for example, that SS0 is muxed as native
chip select, and there is also a chip at 4 (obviously with a gpio
cs). In that case, when accessing the latter chip, both the SS0 pin
and the gpio pin will be asserted low.
The fix for this is to use the ->unused_native_cs value as channel
number for any spi device which uses a gpio as chip select.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230602115731.708883-1-linux@rasmusvillemoes.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace the tuple devm_clk_get()/clk_prepare_enable() with the
single function devm_clk_get_enabled().
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20230531205550.568340-1-andi.shyti@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Just drop a redundant empty line from the dw_spi_debugfs_init() function
left in the framework of the commit 0178f1e5d984 ("spi-dw-core.c: Fix
error checking for debugfs_create_dir") after removing the last return
statement.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20230530221725.26319-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Having no DMA is not an error. The simplest reason is not having it
configured. SPI will still be usable, so raise a warning instead to
get still some attention.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20230531072850.739021-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A warning added in commit b5762d95607e ("spi: spi-qcom-qspi: Add DMA
mode support") was missing a newline. Add it.
Reported-by: Stephen Boyd <swboyd@chromium.org>
Closes: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/4573857/comment/44331d65_79128099/
Fixes: b5762d95607e ("spi: spi-qcom-qspi: Add DMA mode support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230530111348.1.Ibd1f4827e18a26dc802cd6e5ac300d83dc1bc41c@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Get the fixes into CI for development.
|
|
Merge series from Boerge Struempfel <boerge.struempfel@gmail.com>:
Some spi controller switch the mosi line to high, whenever they are
idle. This may not be desired in all use cases. For example neopixel
leds can get confused and flicker due to misinterpreting the idle state.
Therefore, we introduce a new spi-mode bit, with which the idle behaviour
can be overwritten on a per device basis.
|
|
Merge series from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>:
Hello,
compared to (implicit) v1 sent in March with Message-Id:
<20230309094704.2568531-1-u.kleine-koenig@pengutronix.de>, I reworked
patch 1 on feedback by AngeloGioacchino Del Regno. Patches 2 and 3 got
his Reviewed-by.
Best regards
Uwe
Uwe Kleine-König (3):
spi: mt65xx: Properly handle failures in .remove()
spi: mt65xx: Convert to platform remove callback returning void
spi: mt65xx: Don't disguise a "return 0" as "return ret"
drivers/spi/spi-mt65xx.c | 30 +++++++++++++++++-------------
1 file changed, 17 insertions(+), 13 deletions(-)
base-commit: ac9a78681b921877518763ba0e89202254349d1b
--
2.39.2
|
|
Allow userspace to set SPI_MOSI_IDLE_LOW and the SPI_3WIRE_HIZ mode bit
using the SPI_IOC_WR_MODE32 ioctl.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-4-boerge.struempfel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
By default, the spi-imx controller pulls the mosi line high, whenever it
is idle. This behaviour can be inverted per CS by setting the
corresponding DATA_CTL bit in the config register of the controller.
Also, since the controller mode-bits have to be touched anyways, the
SPI_CPOL and SPI_CPHA are replaced by the combined SPI_MODE_X_MASK flag.
Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com>
Link: https://lore.kernel.org/r/20230530141641.1155691-3-boerge.struempfel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch fixes the error checking in spi-dw-core.c in
debugfs_create_dir. The DebugFS kernel API is developed in
a way that the caller can safely ignore the errors that
occur during the creation of DebugFS nodes.
Signed-off-by: Osama Muhammad <osmtendev@gmail.com>
Link: https://lore.kernel.org/r/20230520224025.14928-1-osmtendev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The `width_available` array is currently placed on the
`f_ospi_supports_op_width()` function's stack.
But the array is never modified. Make it `static const`. This makes the
code slightly smaller and more efficient.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230528195830.164669-3-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use `min_t` instead of `min` with casting the individual arguments.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230528195830.164669-2-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Replace the combination of devm_clk_get_enable() plus clk_prepare_enable()
with devm_clk_get_enabled(). Slightly reduces the amount of boilerplate
code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230528195830.164669-1-lars@metafoo.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Because of the earlier
if (ret)
return ret;
ret is always zero at the end of mtk_spi_suspend(). Write it as explicit
return 0 for slightly improved clearness.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230530081648.2199419-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230530081648.2199419-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Returning an error code in a platform driver's remove function is wrong
most of the time and there is an effort to make the callback return
void. To prepare this rework the function not to exit early.
There wasn't a real problem because if pm runtime resume failed the only
step missing was pm_runtime_disable() which isn't an issue.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230530081648.2199419-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is usually better to request all necessary resources (clocks,
regulators, ...) before starting to make use of them. That way they do
not change state in case one of the resources is not available yet and
probe deferral (-EPROBE_DEFER) is necessary. This is particularly
important for DMA channels and IOMMUs which are not enforced by
fw_devlink yet (unless you use fw_devlink.strict=1).
spi-qup does this in the wrong order, the clocks are enabled and
disabled again when the DMA channels are not available yet.
This causes issues in some cases: On most SoCs one of the SPI QUP
clocks is shared with the UART controller. When using earlycon UART is
actively used during boot but might not have probed yet, usually for
the same reason (waiting for the DMA controller). In this case, the
brief enable/disable cycle ends up gating the clock and further UART
console output will halt the system completely.
Avoid this by requesting the DMA channels before changing the clock
state.
Fixes: 612762e82ae6 ("spi: qup: Add DMA capabilities")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230518-spi-qup-clk-defer-v1-1-f49fc9ca4e02@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230525211047.735789-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
this patch advertise the availability of Dual and Quad SPI mode
for ipm design.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Tim.Kuo <Tim.kuo@mediatek.com>
Link: https://lore.kernel.org/r/20230523112608.10298-1-qii.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When unloading the spi-mt65xx kernel module during an ongoing spi-mem
operation the kernel will Oops shortly after unloading the module.
This is because wait_for_completion_timeout was still running and
returning into the no longer loaded module:
Internal error: Oops: 0000000096000005 [#1] SMP
Modules linked in: [many, but spi-mt65xx is no longer there]
CPU: 0 PID: 2578 Comm: block Tainted: G W O 6.3.0-next-20230428+ #0
Hardware name: Bananapi BPI-R3 (DT)
pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __lock_acquire+0x18c/0x20e8
lr : __lock_acquire+0x9b8/0x20e8
sp : ffffffc009ec3400
x29: ffffffc009ec3400 x28: 0000000000000001 x27: 0000000000000004
x26: ffffff80082888c8 x25: 0000000000000000 x24: 0000000000000000
x23: ffffffc009609da8 x22: ffffff8008288000 x21: ffffff8008288968
x20: 00000000000003c2 x19: ffffff8008be7990 x18: 00000000000002af
x17: 0000000000000000 x16: 0000000000000000 x15: ffffffc008d78970
x14: 000000000000080d x13: 00000000000002af x12: 00000000ffffffea
x11: 00000000ffffefff x10: ffffffc008dd0970 x9 : ffffffc008d78918
x8 : 0000000000017fe8 x7 : 0000000000000001 x6 : 0000000000000000
x5 : ffffff807fb53910 x4 : 0000000000000000 x3 : 0000000000000027
x2 : 0000000000000027 x1 : 0000000000000000 x0 : 00000000000c03c2
Call trace:
__lock_acquire+0x18c/0x20e8
lock_acquire+0x100/0x2a4
_raw_spin_lock_irq+0x58/0x74
__wait_for_common+0xe0/0x1b4
wait_for_completion_timeout+0x1c/0x24
0xffffffc000acc8a4 <--- used to be mtk_spi_transfer_wait
spi_mem_exec_op+0x390/0x3ec
spi_mem_no_dirmap_read+0x6c/0x88
spi_mem_dirmap_read+0xcc/0x12c
spinand_read_page+0xf8/0x1dc
spinand_mtd_read+0x1b4/0x2fc
mtd_read_oob_std+0x58/0x7c
mtd_read_oob+0x8c/0x148
mtd_read+0x50/0x6c
...
Prevent this by completing in mtk_spi_remove if needed.
Fixes: 9f763fd20da7 ("spi: mediatek: add spi memory support for ipm design")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/ZFAF6pJxMu1z6k4w@makrotopia.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When all bits of IER are set to 0, we still can observe the lpspi irq events
when using DMA mode to transfer data.
So disable irq to avoid the too much irq events.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20230505063557.3962220-1-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ecspi IP block on imx51/imx53/imx6 have four native chip
selects. Tell that to the spi core so that any non-gpio chip selects
get validated against that upper bound.
Also set the SPI_MASTER_GPIO_SS so that the core verifies that, in the
case where both native and gpio chip selects are in use, there is at
least one leftover native chip select (or "channel", in the ecspi
language) for use by the slaves sitting on gpio chip selects.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230425134527.483607-3-linux@rasmusvillemoes.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Near the top of the function, spi_imx->controller is set to
controller (and is of course never modified again). The rest of the
function uses a mix of the two expressions.
For consistency, readability and better code generation, drop all the
spi_imx-> indirections.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230425134527.483607-2-linux@rasmusvillemoes.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the missing kernel documentation to silence the build warning.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230523090124.3132-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When working in slave mode it seems the timing is exceedingly tight.
The TX FIFO can never empty, because the master is driving the clock so
zeros would be sent for those bytes where the FIFO is empty.
Return to interleaving the writing of the TX FIFO and the reading
of the RX FIFO to try to ensure the data is available when required.
Fixes: a84c11e16dc2 ("spi: spi-cadence: Avoid read of RX FIFO before its ready")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230518093927.711358-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
