| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Function update_trip_temp() is currently used for the initialization
of trip points as well as for changing trip point temperatures in
sys_set_trip_temp().
This is quite confusing and passing the value of dts->trip_types[trip]
to it so that it can store that value in the same memory location is
not particularly useful, because it only is necessary to set the
trip point type once, at the initialization time.
For this reason, drop the last argument from update_trip_temp() and
introduce configure_trip() calling the former internally for the
initial configuration of trip points.
Modify the majority of update_trip_temp() callers to use
configure_trip() instead of it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
None of the existing callers of intel_soc_dts_iosf_init() passes
INTEL_SOC_DTS_INTERRUPT_NONE as the first argument to it, so the
notification local variable in it is always true and the
notification_support argument of add_dts_thermal_zone() is always
true either.
For this reason, drop the notification local variable from
intel_soc_dts_iosf_init() and the notification_support argument from
add_dts_thermal_zone() and rearrange the latter to always set
writable_trip_cnt and trip_mask.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
SOC_MAX_DTS_SENSORS is already defined in intel_soc_dts_iosf.h which is
included in intel_soc_dts_iosf.c, so it does not need to be defined in
the latter again.
Drop the redundant definition of that symbol from intel_soc_dts_iosf.c.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Both the existing callers of intel_soc_dts_iosf_init() pass 2 as the trip
count argument, so it can be replaced with SOC_MAX_DTS_TRIPS everywhere in
the code and the trip_count argument of that function can be dropped.
This also allows the trip_count field to be dropped from struct
intel_soc_dts_sensor_entry, as it is always equal to 2, and some
related code can be simplified.
Make changes accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
Alderlake N is an E-core only product using Gracemont
micro-architecture. It fits the pre-existing naming scheme perfectly
fine, adhere to it.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230807150405.686834933@infradead.org
|
|
Depends on the interface used, the RAPL registers can be either MSR
indexes or memory mapped IO addresses. Current RAPL common code uses u64
to save both MSR and memory mapped IO registers. With this, when
handling register address with an __iomem annotation, it triggers a
sparse warning like below:
sparse warnings: (new ones prefixed by >>)
>> drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: sparse: incorrect type in initializer (different address spaces) @@ expected unsigned long long [usertype] *tpmi_rapl_regs @@ got void [noderef] __iomem * @@
drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: expected unsigned long long [usertype] *tpmi_rapl_regs
drivers/powercap/intel_rapl_tpmi.c:141:41: sparse: got void [noderef] __iomem *
Fix the problem by using a union to save the registers instead.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307031405.dy3druuy-lkp@intel.com/
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The driver is accessing the thermal zone state to ensure the state is
different from the one we want to set.
We don't want the driver to access the thermal zone device internals.
Actually, the thermal core code already checks if the thermal zone's
state is different before calling this function, thus this check is
duplicate.
Remove it.
Acked-by: srinivas pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use the thermal core API to access the thermal zone "type" field
instead of directly using the structure field. While here, remove
access to the temperature field, as this driver is reporting fake
temperature, which can be replaced with INT3400_FAKE_TEMP. Also
replace hardcoded 20C with INT3400_FAKE_TEMP
Acked-by: srinivas pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These extend the int340x thermal driver, add thermal DT bindings for
some Qcom platforms, add DT bindings and support for Armada AP807 and
MSM8909, allow selecting the bang-bang thermal governor as the default
one, address issues in several thermal drivers for ARM platforms and
clean up code.
Specifics:
- Add new IOCTLs to the int340x thermal driver to allow user space to
retrieve the Passive v2 thermal table (Srinivas Pandruvada)
- Add DT bindings for SM6375, MSM8226 and QCM2290 Qcom platforms
(Konrad Dybcio)
- Add DT bindings and support for QCom MSM8226 (Matti Lehtimäki)
- Add DT bindings for QCom ipq9574 (Praveenkumar I)
- Convert bcm2835 DT bindings to the yaml schema (Stefan Wahren)
- Allow selecting the bang-bang governor as default (Thierry Reding)
- Refactor and prepare the code to set the scene for RCar Gen4
(Wolfram Sang)
- Clean up and fix the QCom tsens drivers. Add DT bindings and
calibration for the MSM8909 platform (Stephan Gerhold)
- Revert a patch introducing a wrong usage of devm_of_iomap() on the
Mediatek platform (Ricardo Cañuelo)
- Fix the clock vs reset ordering in order to conform to the
documentation on the sun8i (Christophe JAILLET)
- Prevent setting up undocumented registers, enable the only
described sensors and add the version 2.1 on the Qoriq sensor (Peng
Fan)
- Add DT bindings and support for the Armada AP807 (Alex Leibovich)
- Update the mlx5 driver with the recent thermal changes (Daniel
Lezcano)
- Convert to platform remove callback returning void on STM32 (Uwe
Kleine-König)
- Add an error information printing for devm_thermal_add_hwmon_sysfs()
and remove the error from the Sun8i, Amlogic, i.MX, TI, K3, Tegra,
Qoriq, Mediateka and QCom (Yangtao Li)
- Register as hwmon sensor for the Generic ADC (Chen-Yu Tsai)
- Use the dev_err_probe() function in the QCom tsens alarm driver
(Luca Weiss)"
* tag 'thermal-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (39 commits)
thermal/drivers/qcom/temp-alarm: Use dev_err_probe
thermal/drivers/generic-adc: Register thermal zones as hwmon sensors
thermal/drivers/mediatek/lvts_thermal: Remove redundant msg in lvts_ctrl_start()
thermal/drivers/qcom: Remove redundant msg at probe time
thermal/drivers/ti-soc: Remove redundant msg in ti_thermal_expose_sensor()
thermal/drivers/qoriq: Remove redundant msg in qoriq_tmu_register_tmu_zone()
thermal/drivers/tegra: Remove redundant msg in tegra_tsensor_register_channel()
drivers/thermal/k3: Remove redundant msg in k3_bandgap_probe()
thermal/drivers/imx: Remove redundant msg in imx8mm_tmu_probe() and imx_sc_thermal_probe()
thermal/drivers/amlogic: Remove redundant msg in amlogic_thermal_probe()
thermal/drivers/sun8i: Remove redundant msg in sun8i_ths_register()
thermal/hwmon: Add error information printing for devm_thermal_add_hwmon_sysfs()
thermal/drivers/stm32: Convert to platform remove callback returning void
net/mlx5: Update the driver with the recent thermal changes
thermal/drivers/armada: Add support for AP807 thermal data
dt-bindings: armada-thermal: Add armada-ap807-thermal compatible
thermal/drivers/qoriq: Support version 2.1
thermal/drivers/qoriq: Only enable supported sensors
thermal/drivers/qoriq: No need to program site adjustment register
thermal/drivers/mediatek/lvts_thermal: Register thermal zones as hwmon sensors
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add Intel TPMI (Topology Aware Register and PM Capsule
Interface) support to the power capping subsystem, extend the
intel_idle driver to work in VM guests where MWAIT is not available,
extend the system-wide power management diagnostics, fix bugs and
clean up code.
Specifics:
- Introduce power capping core support for Intel TPMI (Topology Aware
Register and PM Capsule Interface) and a TPMI interface driver for
Intel RAPL (Zhang Rui, Dan Carpenter)
- Fix CONFIG_IOSF_MBI dependency in the Intel RAPL power capping
driver (Zhang Rui)
- Fix invalid initialization for pl4_supported field in the Intel
RAPL power capping driver (Sumeet Pawnikar)
- Clean up the intel_idle driver, make it work with VM guests that
cannot use the MWAIT instruction and address the case in which the
host may enter a deep idle state when the guest is idle (Arjan van
de Ven)
- Prevent cpufreq drivers that provide the ->adjust_perf() callback
without a ->fast_switch() one which is used as a fallback from the
former in some cases (Wyes Karny)
- Fix some issues related to the AMD P-state cpufreq driver (Mario
Limonciello, Wyes Karny)
- Fix the energy_performance_preference attribute handling in the
intel_pstate driver in passive mode (Tero Kristo)
- Fix the handling of pm_suspend_target_state when CONFIG_PM is unset
(Kai-Heng Feng)
- Correct spelling mistake in a comment in the hibernation code (Wang
Honghui)
- Add arch_resume_nosmt() prototype to avoid a "missing prototypes"
build warning (Arnd Bergmann)
- Restrict pm_pr_dbg() to system-wide power transitions and use it in
a few additional places (Mario Limonciello)
- Drop verification of in-params from genpd_add_device() and ensure
that all of its callers will do it (Ulf Hansson)
- Prevent possible integer overflows from occurring in
genpd_parse_state() (Nikita Zhandarovich)
- Reorder fieldls in 'struct devfreq_dev_status' to reduce its size
somewhat (Christophe JAILLET)
- Ensure that the Exynos PPMU driver is already loaded before the
Exynos Bus driver starts probing so as to avoid a possible freeze
loading of the kernel modules (Marek Szyprowski)
- Fix variable deferencing before NULL check in the mtk-cci devfreq
driver (Sukrut Bellary)"
* tag 'pm-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (42 commits)
intel_idle: Add a "Long HLT" C1 state for the VM guest mode
cpufreq: intel_pstate: Fix energy_performance_preference for passive
cpufreq: amd-pstate: Add a kernel config option to set default mode
cpufreq: amd-pstate: Set a fallback policy based on preferred_profile
ACPI: CPPC: Add definition for undefined FADT preferred PM profile value
cpufreq: amd-pstate: Set default governor to schedutil
PM: domains: Move the verification of in-params from genpd_add_device()
cpufreq: amd-pstate: Make amd-pstate EPP driver name hyphenated
cpufreq: amd-pstate: Write CPPC enable bit per-socket
intel_idle: Add support for using intel_idle in a VM guest using just hlt
cpufreq: Fail driver register if it has adjust_perf without fast_switch
intel_idle: clean up the (new) state_update_enter_method function
intel_idle: refactor state->enter manipulation into its own function
platform/x86/amd: pmc: Use pm_pr_dbg() for suspend related messages
pinctrl: amd: Use pm_pr_dbg to show debugging messages
ACPI: x86: Add pm_debug_messages for LPS0 _DSM state tracking
include/linux/suspend.h: Only show pm_pr_dbg messages at suspend/resume
powercap: RAPL: Fix a NULL vs IS_ERR() bug
powercap: RAPL: Fix CONFIG_IOSF_MBI dependency
powercap: RAPL: fix invalid initialization for pl4_supported field
...
|
|
|
|
Merge power capping updates for 6.5-rc1:
- Introduce power capping core support for Intel TPMI (Topology Aware
Register and PM Capsule Interface) and a TPMI interface driver for
Intel RAPL (Zhang Rui, Dan Carpenter).
- Fix CONFIG_IOSF_MBI dependency in the Intel RAPL power capping
driver (Zhang Rui).
- Fix invalid initialization for pl4_supported field in the Intel RAPL
power capping driver (Sumeet Pawnikar).
* powercap:
powercap: RAPL: Fix a NULL vs IS_ERR() bug
powercap: RAPL: Fix CONFIG_IOSF_MBI dependency
powercap: RAPL: fix invalid initialization for pl4_supported field
powercap: intel_rapl: Introduce RAPL TPMI interface driver
powercap: intel_rapl: Introduce core support for TPMI interface
powercap: intel_rapl: Introduce RAPL I/F type
powercap: intel_rapl: Make cpu optional for rapl_package
powercap: intel_rapl: Remove redundant cpu parameter
powercap: intel_rapl: Add support for lock bit per Power Limit
powercap: intel_rapl: Cleanup Power Limits support
powercap: intel_rapl: Use bitmap for Power Limits
powercap: intel_rapl: Change primitive order
powercap: intel_rapl: Use index to initialize primitive information
powercap: intel_rapl: Support per domain energy/power/time unit
powercap: intel_rapl: Support per Interface primitive information
powercap: intel_rapl: Support per Interface rapl_defaults
powercap: intel_rapl: Allow probing without CPUID match
powercap: intel_rapl: Remove unused field in struct rapl_if_priv
|
|
Since commit 955fb8719efb ("thermal/intel/intel_soc_dts_iosf: Use Intel
TCC library") intel_soc_dts_iosf is reporting the wrong temperature.
The driver expects tj_max to be in milli-degrees-celcius but after
the switch to the TCC library this is now in degrees celcius so
instead of e.g. 90000 it is set to 90 causing a temperature 45
degrees below tj_max to be reported as -44910 milli-degrees
instead of as 45000 milli-degrees.
Fix this by adding back the lost factor of 1000.
Fixes: 955fb8719efb ("thermal/intel/intel_soc_dts_iosf: Use Intel TCC library")
Reported-by: Bernhard Krug <b.krug@elektronenpumpe.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Export Passive version 2 table similar to the way _TRT and _ART tables
via IOCTLs.
This removes need for binary utility to read ACPI Passive 2 table by
providing open source support. This table already has open source
implementation in the user space thermald, when the table is part of
data vault exported by the int3400 sysfs.
This table is supported in some older platforms before Ice Lake
generation.
Passive 2 tables contain multiple entries. Each entry has following
fields:
* Source: Named Reference (String). This is the source device for
temperature.
* Target: Named Reference (String). This is the target device to
control.
* Priority: Priority of this device compared to others.
* SamplingPeriod: Time Period in 1/10 of seconds unit.
* PassiveTemp: Passive Temperature in 1/10 of Kelvin.
* SourceDomain: Domain for the source (00:Processor, others reserved).
* ControlKnob: Type of control knob (00:Power Limit 1, others: reserved)
* Limit: The target state to set on reaching passive temperature.
This can be a string "max", "min" or a power limit value.
* LimitStepSize: Step size during activation.
* UnLimitStepSize: Step size during deactivation.
* Reserved1: Reserved
Three IOCTLs are added similar to IOCTLs for reading TRT:
ACPI_THERMAL_GET_PSVT_COUNT: Number of passive 2 entries.
ACPI_THERMAL_GET_PSVT_LEN: Total return data size (count x each
passive 2 entry size).
ACPI_THERMAL_GET_PSVT: Get the data as an array of objects with
passive 2 entries.
This change is based on original development done by:
Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog and subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Prior to the commit "763bd29fd3d1 ("thermal: int340x_thermal: Use
sysfs_emit_at() instead of scnprintf()", there was a new line after each
UUID string.
With the newline removed, existing user space like "thermald" fails to
compare each supported UUID as it is using getline() to read UUID and
apply correct thermal table.
To avoid breaking existing user space, add newline after each UUID string.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 763bd29fd3d1 ("thermal: int340x_thermal: Use sysfs_emit_at() instead of scnprintf()")
Cc: 6.3+ <stable@vger.kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Different RAPL Interfaces may have different primitive information and
rapl_defaults calls.
To better distinguish this difference in the RAPL framework code,
introduce a new enum to represent different types of RAPL Interfaces.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
MSR RAPL Interface always removes a rapl_package when all the CPUs in
that rapl_package are offlined. This is because it relies on an online
CPU to access the MSR.
But for RAPL Interface using MMIO registers, when all the cpus within
the rapl_package are offlined,
1. the register can still be accessed
2. monitoring and setting the Power Pimits for the rapl_package is still
meaningful because of uncore power.
This means that, a valid rapl_package doesn't rely on one or more cpus
being onlined.
For this sense, make cpu optional for rapl_package. A rapl_package can
be registered either using a CPU id to represent the physical
package/die, or using the physical package id directly.
Note that, the thermal throttling interrupt is not disabled via
MSR_IA32_PACKAGE_THERM_INTERRUPT for such rapl_package at the moment.
If it is still needed in the future, this can be achieved by selecting
an onlined CPU using the physical package id.
Note that, processor_thermal_rapl, the current MMIO RAPL Interface
driver, can also be converted to register using a package id instead.
But this is not done right now because processor_thermal_rapl driver
works on single-package systems only, and offlining the only package
will not happen. So keep the previous logic.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently, a RAPL package is registered with the number of Power Limits
supported in each RAPL domain. But this doesn't tell which Power Limits
are available. Using the number of Power Limits supported to guess the
availability of each Power Limit is fragile.
Use bitmap to represent the availability of each Power Limit.
Note that PL1 is mandatory thus it does not need to be set explicitly by
the RAPL Interface drivers.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If cur_state for the powerclamp cooling device is set to the default
minimum state of 0, without setting first to cur_state > 0, this results
in NULL pointer access.
This NULL pointer access happens in the powercap core idle-inject
function idle_inject_set_duration() as there is no NULL check for
idle_inject_device pointer. This pointer must be allocated by calling
idle_inject_register() or idle_inject_register_full().
In the function powerclamp_set_cur_state(), idle_inject_device pointer
is allocated only when the cur_state > 0. But setting 0 without changing
to any other state, idle_inject_set_duration() will be called with a
NULL idle_inject_device pointer.
To address this, just return from powerclamp_set_cur_state() if the
current cooling device state is the same as the last one. Since the
power-up default cooling device state is 0, changing the state to 0
again here will return without calling idle_inject_set_duration().
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fixes: 8526eb7fc75a ("thermal: intel: powerclamp: Use powercap idle-inject feature")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=217386
Tested-by: Risto A. Paju <teknohog@iki.fi>
Cc: 6.3+ <stable@kernel.org> # 6.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
According to my information, there are no active users of this driver in
the field.
Moreover, it does some really questionable things and gets in the way of
thermal core improvements, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The pch_critical() callback accesses the thermal zone device structure
internals, it dereferences the thermal zone struct device and the 'type'.
Use the available accessors instead of accessing the structure directly.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add support for DLVR (Digital Linear Voltage Regulator) attributes,
which can be used to control RFIM.
Here instead of "fivr" another directory "dlvr" is created with DLVR
attributes:
/sys/bus/pci/devices/0000:00:04.0/dlvr
├── dlvr_freq_mhz
├── dlvr_freq_select
├── dlvr_hardware_rev
├── dlvr_pll_busy
├── dlvr_rfim_enable
└── dlvr_spread_spectrum_pct
└── dlvr_control_mode
└── dlvr_control_lock
Attributes
dlvr_freq_mhz (RO):
Current DLVR PLL frequency in MHz.
dlvr_freq_select (RW):
Sets DLVR PLL clock frequency.
dlvr_hardware_rev (RO):
DLVR hardware revision.
dlvr_pll_busy (RO):
PLL can't accept frequency change when set.
dlvr_rfim_enable (RW):
0: Disable RF frequency hopping, 1: Enable RF frequency hopping.
dlvr_control_mode (RW):
Specifies how frequencies are spread. 0: Down spread, 1: Spread in Center.
dlvr_control_lock (RW):
1: future writes are ignored.
dlvr_spread_spectrum_pct (RW)
A write to this register updates the DLVR spread spectrum percent value.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Some older processors don't allow BIT(13) and BIT(15) in the current
mask set by "THERM_STATUS_CLEAR_CORE_MASK". This results in:
unchecked MSR access error: WRMSR to 0x19c (tried to
write 0x000000000000aaa8) at rIP: 0xffffffff816f66a6
(throttle_active_work+0xa6/0x1d0)
To avoid unchecked MSR issues, check CPUID for each relevant feature and
use that information to set the supported feature bits only in the
"clear" mask for cores. Do the same for the analogous package mask set
by "THERM_STATUS_CLEAR_PKG_MASK".
Introduce functions thermal_intr_init_core_clear_mask() and
thermal_intr_init_pkg_clear_mask() to set core and package mask bits,
respectively. These functions are called during initialization.
Fixes: 6fe1e64b6026 ("thermal: intel: Prevent accidental clearing of HFI status")
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://lore.kernel.org/lkml/cdf43fb423368ee3994124a9e8c9b4f8d00712c6.camel@linux.intel.com/T/
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 6.2+ <stable@kernel.org> # 6.2+
[ rjw: Renamed 2 funtions and 2 static variables, edited subject and
changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
When cpumask is specified as a module parameter the value is
overwritten by the module init routine. This can easily be fixed
by checking to see if the mask has already been allocated in the
init routine.
When max_idle is specified as a module parameter a panic will occur.
The problem is that the idle_injection_cpu_mask is not allocated until
the module init routine executes. This can easily be fixed by allocating
the cpumask if it's not already allocated.
Fixes: ebf519710218 ("thermal: intel: powerclamp: Add two module parameters")
Signed-off-by: David Arcari <darcari@redhat.com>
Reviewed-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 52f04f10b900 ("thermal: intel: int340x: processor_thermal: Fix
deadlock") addressed deadlock issue during user space trip update. But it
missed a case when thermal zone device is disabled when user writes 0.
Call to thermal_zone_device_disable() also causes deadlock as it also
tries to lock tz->lock, which is already claimed by trip_point_temp_store()
in the thermal core code.
Remove call to thermal_zone_device_disable() in the function
sys_set_trip_temp(), which is called from trip_point_temp_store().
Fixes: 52f04f10b900 ("thermal: intel: int340x: processor_thermal: Fix deadlock")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 6.2+ <stable@vger.kernel.org> # 6.2+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Merge an x86_pkg_temp_thermal Intel thermal driver fix (Zhang Rui).
* thermal-intel:
thermal: intel: x86_pkg_temp_thermal: Add lower bound check for sysfs input
|
|
When setting a trip point temperature from sysfs, there is an upper
bound check on the user input, but no lower bound check.
As hardware register has 7 bits for a trip point temperature, the offset
to tj_max of the input temperature must be equal to/less than 0x7f.
Or else,
1. bogus temperature is updated into the trip temperature bits.
2. the upper bits of the register can be polluted.
For example,
$ rdmsr 0x1b2
2000003
$ echo -180000 > /sys/class/thermal/thermal_zone1/trip_point_1_temp
$ rdmsr 0x1b2
3980003
Not only the trip point temp is set to 76C on this platform (tj_max is
100), the Power Notification (Bit 24) is also enabled erronously.
Fix the problem by adding lower bound check for sysfs input.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/all/add7a378-4d50-4ba1-81d3-a0c17db25a0b@kili.mountain/
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Merge thermal control updates for 6.4-rc1:
- Add a thermal zone 'devdata' accessor and modify several drivers to
use it (Daniel Lezcano).
- Prevent drivers from using the 'device' internal thermal zone
structure field directly (Daniel Lezcano).
- Clean up the hwmon thermal driver (Daniel Lezcano).
- Add thermal zone id accessor and thermal zone type accessor
and prevent drivers from using thermal zone fields directly (Daniel
Lezcano).
- Clean up the acerhdf and tegra thermal drivers (Daniel Lezcano).
* thermal-core:
thermal/drivers/acerhdf: Remove pointless governor test
thermal/drivers/acerhdf: Make interval setting only at module load time
thermal/drivers/tegra: Remove unneeded lock when setting a trip point
thermal/hwmon: Use the thermal_core.h header
thermal/drivers/da9062: Don't access the thermal zone device fields
thermal: Use thermal_zone_device_type() accessor
thermal: Add a thermal zone id accessor
thermal/drivers/spear: Don't use tz->device but pdev->dev
thermal/core: Add thermal_zone_device structure 'type' accessor
thermal: Don't use 'device' internal thermal zone structure field
thermal/hwmon: Use the right device for devm_thermal_add_hwmon_sysfs()
thermal/hwmon: Do not set no_hwmon before calling thermal_add_hwmon_sysfs()
thermal: Remove debug or error messages in get_temp() ops
thermal/core: Show a debug message when get_temp() fails
thermal/core: Use the thermal zone 'devdata' accessor in remaining drivers
thermal/core: Use the thermal zone 'devdata' accessor in hwmon located drivers
thermal/core: Use the thermal zone 'devdata' accessor in thermal located drivers
thermal/core: Add a thermal zone 'devdata' accessor
|
|
The thermal zone device structure is exposed to the different drivers
and obviously they access the internals while that should be
restricted to the core thermal code.
In order to self-encapsulate the thermal core code, we need to prevent
the drivers accessing directly the thermal zone structure and provide
accessor functions to deal with.
Use the devdata accessor introduced in the previous patch.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> #R-Car
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #MediaTek auxadc and lvts
Reviewed-by: Balsam CHIHI <bchihi@baylibre.com> #Mediatek lvts
Reviewed-by: Adam Ward <DLG-Adam.Ward.opensource@dm.renesas.com> #da9062
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com> #spread
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> #sun8i_thermal
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com> #Broadcom
Reviewed-by: Dhruva Gole <d-gole@ti.com> # K3 bandgap
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de> #rockchip
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> #uniphier
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When user space updates the trip point there is a deadlock, which results
in caller gets blocked forever.
Commit 05eeee2b51b4 ("thermal/core: Protect sysfs accesses to thermal
operations with thermal zone mutex"), added a mutex for tz->lock in the
function trip_point_temp_store(). Hence, trip set callback() can't
call any thermal zone API as they are protected with the same mutex lock.
The callback here calling thermal_zone_device_enable(), which will result
in deadlock.
Move the thermal_zone_device_enable() to proc_thermal_pci_probe() to
avoid this deadlock.
Fixes: 05eeee2b51b4 ("thermal/core: Protect sysfs accesses to thermal operations with thermal zone mutex")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Cc: 6.2+ <stable@vger.kernel.org> # 6.2+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
REGMAP is a hidden (not user visible) symbol. Users cannot set it
directly thru "make *config", so drivers should select it instead of
depending on it if they need it.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on REGMAP" to "select REGMAP".
Fixes: b474303ffd57 ("thermal: add Intel BXT WhiskeyCove PMIC thermal driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If alloc_soc_dts() fails, then we can just return. Trying to free
"soc_dts" will lead to an Oops.
Fixes: 8c1876939663 ("thermal: intel Quark SoC X1000 DTS thermal driver")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As the name states "thermal_core.h" is the header file for the core
components of the thermal framework.
Too many drivers are including it. Hopefully the recent cleanups
helped to self encapsulate the code a bit more and prevented the
drivers to need this header.
Remove this inclusion in every place where it is possible.
Some other drivers did a confusion with the core header and the one
exported in linux/thermal.h. They include the former instead of the
latter. The changes also fix this.
The tegra/soctherm driver still remains as it uses an internal
function which need to be replaced.
The Intel HFI driver uses the netlink internal framework core and
should be changed to prevent to deal with the internals.
No functional changes intended.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> # armada_thermal.c
Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> # uniphier_thermal.c
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> # rcar_gen3_thermal.c
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> # amlogic_thermal.c
Acked-by: Florian Fainelli <f.fainelli@gmail.com> # bcm2835_thermal.c
Acked-by: Thierry Reding <treding@nvidia.com> # tegra30-tsensor.c
Link: https://lore.kernel.org/r/20230206153432.1017282-1-daniel.lezcano@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In some use cases, it is desirable to only inject idle on certain set
of CPUs. For example on Alder Lake systems, it is possible that we force
idle only on P-Cores for thermal reasons. Also the idle percent can be
more than 50% if we only choose partial set of CPUs in the system.
Introduce 2 new module parameters for this purpose. They can be only
changed when the cooling device is inactive.
cpumask (Read/Write): A bit mask of CPUs to inject idle. The format of
this bitmask is same as used in other subsystems like in
/proc/irq/*/smp_affinity. The mask is comma separated 32 bit groups.
Each CPU is one bit. For example for 256 CPU system the full mask is:
ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff,ffffffff
The rightmost mask is for CPU 0-32.
max_idle (Read/Write): Maximum injected idle time to the total CPU time
ratio in percent range from 1 to 100. Even if the cooling device max_state
is always 100 (100%), this parameter allows to add a max idle percent
limit. The default is 50, to match the current implementation of powerclamp
driver. Also doesn't allow value more than 75, if the cpumask includes
every CPU present in the system.
Also when the cpumask doesn't include every CPU, there is no use of
compensation using package C-state idle counters. Hence don't start
package C-state polling thread even for a single package or a single die
system in this case.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After the switch to use the powercap/idle-inject framework in the Intel
powerclamp driver, the idle duration unit is microsecond.
However, the module parameter for idle duration is in milliseconds, so
convert it to microseconds in the "set" callback and back to milliseconds
in a new "get" callback.
While here, also use mutex protection for setting and getting "duration".
The other uses of "duration" are already protected by the mutex.
Fixes: 8526eb7fc75a ("thermal: intel: powerclamp: Use powercap idle-inject feature")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the user is reading cur_state from the thermal cooling device for
Intel powerclamp device:
- It returns the idle ratio from Package C-state counters when
there is active idle injection session.
- -1, when there is no active idle injection session.
This information is not very useful as the package C-state counters vary
a lot from read to read. Instead just return the last requested cur_state.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make the intel_quark_dts_thermal driver register an array of generic
trip points along with the thermal zone and drop the trip points
thermal zone callbacks that are not used any more from it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@kernel.org>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are two idle injection implementation in the Linux kernel. One
via intel_powerclamp and the other using powercap/idle_inject. Both
implementation end up in calling play_idle* function from a FIFO
priority thread. Both can't be used at the same time.
It is better to use one idle injection framework for better
maintainability. In this way, there is only one caller for play_idle.
Here powercap/idle_inject can be used for both per-core and for system
wide idle injection. This framework has a well defined interface which
allow registry for per-core or for all CPUs (system wide).
This reduces code complexity in the intel powerclamp driver as all the
per CPU kthreads, delayed work and calls to play_idle can be removed.
The changes include:
- Remove unneeded include files
- Remove per CPU kthread workers: balancing_work and idle_injection_work.
- Reuse the compensation related code by moving from previous worker
thread to idle_injection callback.
- Adjust the idle_duration and runtime by using powercap/idle_inject
interface.
- Remove all variables, which are not required once powercap/idle_inject
is used.
- Add mutex to avoid race during removal of idle injection during module
unload and user action to change idle inject percent. Also for
protection during dynamic adjustment of run and idle time from
update() callback.
- Remove online/offline callbacks to designate control CPU
- Use cpu_present_mask global variable for CPU mask
- Remove hot plug locks
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The powerclamp cooling device cur_state shows actual idle observed by
package C-state idle counters. But the implementation is not sufficient
for multi package or multi die system. The cur_state value is incorrect.
On these systems, these counters must be read from each package/die and
somehow aggregate them. But there is no good method for aggregation.
It was not a problem when explicit CPU model addition was required to
enable intel powerclamp. In this way certain CPU models could have
been avoided. But with the removal of CPU model check with the
availability of Package C-state counters, the driver is loaded on most
of the recent systems.
For multi package/die systems, just show the actual target idle state,
the system is trying to achieve. In powerclamp this is the user set
state minus one.
Also there is no use of starting a worker thread for polling package
C-state counters and applying any compensation for multiple package
or multiple die systems.
Fixes: b721ca0d1927 ("thermal/powerclamp: remove cpu whitelist")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Because the only member of struct board_info is the name, the
board_info[] array of struct board_info elements can be replaced with
an array of strings.
Modify the code accordingly and drop struct board_info.
No intentional functional impact.
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Use capitals in the names of the board ID symbols and add the PCH_
prefix to each of them for consistency.
Also rename the board_ids enum accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Fold pch_suspend() and pch_resume(), that each have only one caller,
into their respective callers to make the code somewhat easier to
follow.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Fold two functions, pch_hw_init() and pch_get_temp(), that each have
only one caller, into their respective callers to make the code somewhat
easier to follow.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
The same device operations object is pointed to by all of the board
configurations in the driver, so effectively the same operations
callbacks are used by all of them which only adds overhead (that can
be significant due to retpolines) for no real purpose.
For this reason, drop the device operations object and replace the
respective callback invocations by direct calls to the specific
functions that were previously pointed to by callback pointers.
No intentional change in behavior.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Because the same device operations callbacks are used for all supported
boards, they are in fact generic, so rename them to reflect that.
Also rename the operations object itself for consistency.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Both pch_wpt_init() and pch_wpt_get_temp() can return the proper
result via their return values, so they do not need to use return
pointers.
Modify them accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Modify pch_wpt_add_acpi_psv_trip() to return an int value instead of
using a return pointer for that.
While at it, drop an excessive empty code line.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
|
Instead of using snprintf() to populate the ACPI object name in
int340x_thermal_set_trip_temp(), use an appropriate initializer
and make the function fail if its trip argument is greater than 9,
because ACPI object names can only be 4 characters long and it does
not make sense to even try to evaluate objects with longer names (that
argument is guaranteed to be non-negative, because it comes from the
thermal code that will not pass negative trip numbers to zone
callbacks).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
|
