summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2014-10-15cxgb4 : Fix build failure in cxgb4 when ipv6 is disabled/not in-builtAnish Bhatt2-1/+9
cxgb4 ipv6 does not guard against ipv6 being disabled, or the standard ipv6 module vs inbuilt tri-state issue. This was fixed for cxgb4i & iw_cxgb4 but missed for cxgb4. Signed-off-by: Anish Bhatt <anish@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15cxgb4i : Remove duplicated CLIP handling codeAnish Bhatt2-133/+7
cxgb4 already handles CLIP updates from a previous changeset for iw_cxgb4, there is no need to have this functionality in cxgb4i. Remove duplicated code Signed-off-by: Anish Bhatt <anish@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15qlcnic: Fix number of arguments in destroy tx context commandRajesh Borundia1-1/+1
o Number of arguments taken by destroy tx command is three instead of two. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15qlcnic: Fix programming number of arguments in a command.Rajesh Borundia1-2/+2
o Initially we were programming maximum number of arguments. Instead we should program number of arguments required in a command. o Maximum number of arguments for 82xx adapter is four. Fix it for GET_ESWITCH_STATS command. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15cxgb4: Fix FW flash logic using ethtoolHariprasad Shenai3-6/+16
Use t4_fw_upgrade instead of t4_load_fw to write firmware into FLASH, since t4_load_fw doesn't co-ordinate with the firmware and the adapter can get hosed enough to require a power cycle of the system. Based on original work by Casey Leedom <leedom@chelsio.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15stmmac: dwmac-sti: review the glue-logic for STi4xx and STiD127 SoCsGiuseppe CAVALLARO1-169/+205
This patch is to review the whole glue logic adopted on STi SoCs that was bugged. In the old glue-logic there was a lot of confusion when setup the retiming especially for STiD127 where, for example, the bits 6 and 7 (in the GMAC control register) have a different meaning of what is used for STiH4xx SoCs. So we cannot adopt the same glue for all these SoCs. Moreover, GiGa on STiD127 didn't work and, for all the SoCs, the RGMII couldn't run when the speed was 10Mbps (because the clock was not properly managed). Note that the phy clock needs to be provided by the platform as well as documented in the related binding file (updated as consequence). The old code supported too many configurations never adopted and validated. This made the code very complex to maintain and debug in case of issues. The patch simplifies all the configurations as commented in the tables inside the file and obviously it has been tested on all the boards based on the SoCs mentioned. With this patch, the dwmac-sti is also ready to support new configurations that will be available on next SoC generations. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15stmmac: make the STi Layer compatible to STiH407Giuseppe CAVALLARO1-0/+1
This adds the missing compatibility to the STiH407 SoC. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15stmmac: platform: fix FIXED_PHY support.Giuseppe CAVALLARO1-5/+10
On several STi platforms: e.g. stihxxx-b2120 an Ethernet switch is embedded and connected to the stmmac via RGMII mode. So this is managed by using the FIXED_PHY. In that case, the support in the platform needs to be fixed to allow the stmmac to dialog with the switch via fixed-link by using phy_bus_name property. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15dsa: mv88e6171: Fix tag_protocol checkGuenter Roeck1-1/+1
tag_protocol is now an enum, so drivers have to check against it. Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15drivers: net: xgene: Add SGMII based 1GbE ethtool supportIyappan Subramanian1-8/+17
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Keyur Chudgar <kchudgar@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15drivers: net: xgene: Add SGMII based 1GbE supportIyappan Subramanian7-5/+453
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Keyur Chudgar <kchudgar@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-15drivers: net: xgene: Preparing for adding SGMII based 1GbEIyappan Subramanian6-8/+8
- Added link_state function pointer to the xgene__mac_ops structure - Moved ring manager (pdata->rm) assignment to xgene_enet_setup_ops - Removed unused variable (pdata->phy_addr) and macro (FULL_DUPLEX) Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Keyur Chudgar <kchudgar@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14drivers: net: cpsw: remove child devices while driver detachMugunthan V N1-0/+10
remove all the child devices from the system to make sure that re-insert of cpsw module doesn't fail on child device populated by of_platform_populate(). Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14drivers: net: davinci_cpdma: remove spinlock as SOFTIRQ-unsafe lock order ↵Mugunthan V N1-4/+0
detected remove spinlock in cpdma_desc_pool_destroy() as there is no active cpdma channel and iounmap should be called without auquiring lock. root@dra7xx-evm:~# modprobe -r ti_cpsw [ 50.539743] [ 50.541312] ====================================================== [ 50.547796] [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ] [ 50.554826] 3.14.19-02124-g95c5b7b #308 Not tainted [ 50.559939] ------------------------------------------------------ [ 50.566416] modprobe/1921 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: [ 50.573347] (vmap_area_lock){+.+...}, at: [<c01127fc>] find_vmap_area+0x10/0x6c [ 50.581132] [ 50.581132] and this task is already holding: [ 50.587249] (&(&pool->lock)->rlock#2){..-...}, at: [<bf017c74>] cpdma_ctlr_destroy+0x5c/0x114 [davinci_cpdma] [ 50.597766] which would create a new lock dependency: [ 50.603048] (&(&pool->lock)->rlock#2){..-...} -> (vmap_area_lock){+.+...} [ 50.610296] [ 50.610296] but this new dependency connects a SOFTIRQ-irq-safe lock: [ 50.618601] (&(&pool->lock)->rlock#2){..-...} ... which became SOFTIRQ-irq-safe at: [ 50.626829] [<c06585a4>] _raw_spin_lock_irqsave+0x38/0x4c [ 50.632677] [<bf01773c>] cpdma_desc_free.constprop.7+0x28/0x58 [davinci_cpdma] [ 50.640437] [<bf0177e8>] __cpdma_chan_free+0x7c/0xa8 [davinci_cpdma] [ 50.647289] [<bf017908>] __cpdma_chan_process+0xf4/0x134 [davinci_cpdma] [ 50.654512] [<bf017984>] cpdma_chan_process+0x3c/0x54 [davinci_cpdma] [ 50.661455] [<bf0277e8>] cpsw_poll+0x14/0xa8 [ti_cpsw] [ 50.667038] [<c05844f4>] net_rx_action+0xc0/0x1e8 [ 50.672150] [<c0048234>] __do_softirq+0xcc/0x304 [ 50.677183] [<c004873c>] irq_exit+0xa8/0xfc [ 50.681751] [<c000eeac>] handle_IRQ+0x50/0xb0 [ 50.686513] [<c0008638>] gic_handle_irq+0x28/0x5c [ 50.691628] [<c06590a4>] __irq_svc+0x44/0x5c [ 50.696289] [<c0658ab4>] _raw_spin_unlock_irqrestore+0x34/0x44 [ 50.702591] [<c065a9c4>] do_page_fault.part.9+0x144/0x3c4 [ 50.708433] [<c065acb8>] do_page_fault+0x74/0x84 [ 50.713453] [<c00083dc>] do_DataAbort+0x34/0x98 [ 50.718391] [<c065923c>] __dabt_usr+0x3c/0x40 [ 50.723148] [ 50.723148] to a SOFTIRQ-irq-unsafe lock: [ 50.728893] (vmap_area_lock){+.+...} ... which became SOFTIRQ-irq-unsafe at: [ 50.736476] ... [<c06584e8>] _raw_spin_lock+0x28/0x38 [ 50.741876] [<c011376c>] alloc_vmap_area.isra.28+0xb8/0x300 [ 50.747908] [<c0113a44>] __get_vm_area_node.isra.29+0x90/0x134 [ 50.754210] [<c011486c>] get_vm_area_caller+0x3c/0x48 [ 50.759692] [<c0114be0>] vmap+0x40/0x78 [ 50.763900] [<c09442f0>] check_writebuffer_bugs+0x54/0x1a0 [ 50.769835] [<c093eac0>] start_kernel+0x320/0x388 [ 50.774952] [<80008074>] 0x80008074 [ 50.778793] [ 50.778793] other info that might help us debug this: [ 50.778793] [ 50.787181] Possible interrupt unsafe locking scenario: [ 50.787181] [ 50.794295] CPU0 CPU1 [ 50.799042] ---- ---- [ 50.803785] lock(vmap_area_lock); [ 50.807446] local_irq_disable(); [ 50.813652] lock(&(&pool->lock)->rlock#2); [ 50.820782] lock(vmap_area_lock); [ 50.827086] <Interrupt> [ 50.829823] lock(&(&pool->lock)->rlock#2); [ 50.834490] [ 50.834490] *** DEADLOCK *** [ 50.834490] [ 50.840695] 4 locks held by modprobe/1921: [ 50.844981] #0: (&__lockdep_no_validate__){......}, at: [<c03e53e8>] driver_detach+0x44/0xb8 [ 50.854038] #1: (&__lockdep_no_validate__){......}, at: [<c03e53f4>] driver_detach+0x50/0xb8 [ 50.863102] #2: (&(&ctlr->lock)->rlock){......}, at: [<bf017c34>] cpdma_ctlr_destroy+0x1c/0x114 [davinci_cpdma] [ 50.873890] #3: (&(&pool->lock)->rlock#2){..-...}, at: [<bf017c74>] cpdma_ctlr_destroy+0x5c/0x114 [davinci_cpdma] [ 50.884871] the dependencies between SOFTIRQ-irq-safe lock and the holding lock: [ 50.892827] -> (&(&pool->lock)->rlock#2){..-...} ops: 167 { [ 50.898703] IN-SOFTIRQ-W at: [ 50.901995] [<c06585a4>] _raw_spin_lock_irqsave+0x38/0x4c [ 50.909476] [<bf01773c>] cpdma_desc_free.constprop.7+0x28/0x58 [davinci_cpdma] [ 50.918878] [<bf0177e8>] __cpdma_chan_free+0x7c/0xa8 [davinci_cpdma] [ 50.927366] [<bf017908>] __cpdma_chan_process+0xf4/0x134 [davinci_cpdma] [ 50.936218] [<bf017984>] cpdma_chan_process+0x3c/0x54 [davinci_cpdma] [ 50.944794] [<bf0277e8>] cpsw_poll+0x14/0xa8 [ti_cpsw] [ 50.952009] [<c05844f4>] net_rx_action+0xc0/0x1e8 [ 50.958765] [<c0048234>] __do_softirq+0xcc/0x304 [ 50.965432] [<c004873c>] irq_exit+0xa8/0xfc [ 50.971635] [<c000eeac>] handle_IRQ+0x50/0xb0 [ 50.978035] [<c0008638>] gic_handle_irq+0x28/0x5c [ 50.984788] [<c06590a4>] __irq_svc+0x44/0x5c [ 50.991085] [<c0658ab4>] _raw_spin_unlock_irqrestore+0x34/0x44 [ 50.999023] [<c065a9c4>] do_page_fault.part.9+0x144/0x3c4 [ 51.006510] [<c065acb8>] do_page_fault+0x74/0x84 [ 51.013171] [<c00083dc>] do_DataAbort+0x34/0x98 [ 51.019738] [<c065923c>] __dabt_usr+0x3c/0x40 [ 51.026129] INITIAL USE at: [ 51.029335] [<c06585a4>] _raw_spin_lock_irqsave+0x38/0x4c [ 51.036729] [<bf017d78>] cpdma_chan_submit+0x4c/0x2f0 [davinci_cpdma] [ 51.045225] [<bf02863c>] cpsw_ndo_open+0x378/0x6bc [ti_cpsw] [ 51.052897] [<c058747c>] __dev_open+0x9c/0x104 [ 51.059287] [<c05876ec>] __dev_change_flags+0x88/0x160 [ 51.066420] [<c05877e4>] dev_change_flags+0x18/0x48 [ 51.073270] [<c05ed51c>] devinet_ioctl+0x61c/0x6e0 [ 51.080029] [<c056ee54>] sock_ioctl+0x5c/0x298 [ 51.086418] [<c01350a4>] do_vfs_ioctl+0x78/0x61c [ 51.092993] [<c01356ac>] SyS_ioctl+0x64/0x74 [ 51.099200] [<c000e580>] ret_fast_syscall+0x0/0x48 [ 51.105956] } [ 51.107696] ... key at: [<bf019000>] __key.21312+0x0/0xfffff650 [davinci_cpdma] [ 51.115912] ... acquired at: [ 51.119019] [<c00899ac>] lock_acquire+0x9c/0x104 [ 51.124138] [<c06584e8>] _raw_spin_lock+0x28/0x38 [ 51.129341] [<c01127fc>] find_vmap_area+0x10/0x6c [ 51.134547] [<c0114960>] remove_vm_area+0x8/0x6c [ 51.139659] [<c0114a7c>] __vunmap+0x20/0xf8 [ 51.144318] [<c001c350>] __arm_iounmap+0x10/0x18 [ 51.149440] [<bf017d08>] cpdma_ctlr_destroy+0xf0/0x114 [davinci_cpdma] [ 51.156560] [<bf026294>] cpsw_remove+0x48/0x8c [ti_cpsw] [ 51.162407] [<c03e62c8>] platform_drv_remove+0x18/0x1c [ 51.168063] [<c03e4c44>] __device_release_driver+0x70/0xc8 [ 51.174094] [<c03e5458>] driver_detach+0xb4/0xb8 [ 51.179212] [<c03e4a6c>] bus_remove_driver+0x4c/0x90 [ 51.184693] [<c00b024c>] SyS_delete_module+0x10c/0x198 [ 51.190355] [<c000e580>] ret_fast_syscall+0x0/0x48 [ 51.195661] [ 51.197217] the dependencies between the lock to be acquired and SOFTIRQ-irq-unsafe lock: [ 51.205986] -> (vmap_area_lock){+.+...} ops: 520 { [ 51.211032] HARDIRQ-ON-W at: [ 51.214321] [<c06584e8>] _raw_spin_lock+0x28/0x38 [ 51.221090] [<c011376c>] alloc_vmap_area.isra.28+0xb8/0x300 [ 51.228750] [<c0113a44>] __get_vm_area_node.isra.29+0x90/0x134 [ 51.236690] [<c011486c>] get_vm_area_caller+0x3c/0x48 [ 51.243811] [<c0114be0>] vmap+0x40/0x78 [ 51.249654] [<c09442f0>] check_writebuffer_bugs+0x54/0x1a0 [ 51.257239] [<c093eac0>] start_kernel+0x320/0x388 [ 51.263994] [<80008074>] 0x80008074 [ 51.269474] SOFTIRQ-ON-W at: [ 51.272769] [<c06584e8>] _raw_spin_lock+0x28/0x38 [ 51.279525] [<c011376c>] alloc_vmap_area.isra.28+0xb8/0x300 [ 51.287190] [<c0113a44>] __get_vm_area_node.isra.29+0x90/0x134 [ 51.295126] [<c011486c>] get_vm_area_caller+0x3c/0x48 [ 51.302245] [<c0114be0>] vmap+0x40/0x78 [ 51.308094] [<c09442f0>] check_writebuffer_bugs+0x54/0x1a0 [ 51.315669] [<c093eac0>] start_kernel+0x320/0x388 [ 51.322423] [<80008074>] 0x80008074 [ 51.327906] INITIAL USE at: [ 51.331112] [<c06584e8>] _raw_spin_lock+0x28/0x38 [ 51.337775] [<c011376c>] alloc_vmap_area.isra.28+0xb8/0x300 [ 51.345352] [<c0113a44>] __get_vm_area_node.isra.29+0x90/0x134 [ 51.353197] [<c011486c>] get_vm_area_caller+0x3c/0x48 [ 51.360224] [<c0114be0>] vmap+0x40/0x78 [ 51.365977] [<c09442f0>] check_writebuffer_bugs+0x54/0x1a0 [ 51.373464] [<c093eac0>] start_kernel+0x320/0x388 [ 51.380131] [<80008074>] 0x80008074 [ 51.385517] } [ 51.387260] ... key at: [<c0a66948>] vmap_area_lock+0x10/0x20 [ 51.393841] ... acquired at: [ 51.396945] [<c00899ac>] lock_acquire+0x9c/0x104 [ 51.402060] [<c06584e8>] _raw_spin_lock+0x28/0x38 [ 51.407266] [<c01127fc>] find_vmap_area+0x10/0x6c [ 51.412478] [<c0114960>] remove_vm_area+0x8/0x6c [ 51.417592] [<c0114a7c>] __vunmap+0x20/0xf8 [ 51.422252] [<c001c350>] __arm_iounmap+0x10/0x18 [ 51.427369] [<bf017d08>] cpdma_ctlr_destroy+0xf0/0x114 [davinci_cpdma] [ 51.434487] [<bf026294>] cpsw_remove+0x48/0x8c [ti_cpsw] [ 51.440336] [<c03e62c8>] platform_drv_remove+0x18/0x1c [ 51.446000] [<c03e4c44>] __device_release_driver+0x70/0xc8 [ 51.452031] [<c03e5458>] driver_detach+0xb4/0xb8 [ 51.457147] [<c03e4a6c>] bus_remove_driver+0x4c/0x90 [ 51.462628] [<c00b024c>] SyS_delete_module+0x10c/0x198 [ 51.468289] [<c000e580>] ret_fast_syscall+0x0/0x48 [ 51.473584] [ 51.475140] [ 51.475140] stack backtrace: [ 51.479703] CPU: 0 PID: 1921 Comm: modprobe Not tainted 3.14.19-02124-g95c5b7b #308 [ 51.487744] [<c0016090>] (unwind_backtrace) from [<c0012060>] (show_stack+0x10/0x14) [ 51.495865] [<c0012060>] (show_stack) from [<c0652a20>] (dump_stack+0x78/0x94) [ 51.503444] [<c0652a20>] (dump_stack) from [<c0086f18>] (check_usage+0x408/0x594) [ 51.511293] [<c0086f18>] (check_usage) from [<c00870f8>] (check_irq_usage+0x54/0xb0) [ 51.519416] [<c00870f8>] (check_irq_usage) from [<c0088724>] (__lock_acquire+0xe54/0x1b90) [ 51.528077] [<c0088724>] (__lock_acquire) from [<c00899ac>] (lock_acquire+0x9c/0x104) [ 51.536291] [<c00899ac>] (lock_acquire) from [<c06584e8>] (_raw_spin_lock+0x28/0x38) [ 51.544417] [<c06584e8>] (_raw_spin_lock) from [<c01127fc>] (find_vmap_area+0x10/0x6c) [ 51.552726] [<c01127fc>] (find_vmap_area) from [<c0114960>] (remove_vm_area+0x8/0x6c) [ 51.560935] [<c0114960>] (remove_vm_area) from [<c0114a7c>] (__vunmap+0x20/0xf8) [ 51.568693] [<c0114a7c>] (__vunmap) from [<c001c350>] (__arm_iounmap+0x10/0x18) [ 51.576362] [<c001c350>] (__arm_iounmap) from [<bf017d08>] (cpdma_ctlr_destroy+0xf0/0x114 [davinci_cpdma]) [ 51.586494] [<bf017d08>] (cpdma_ctlr_destroy [davinci_cpdma]) from [<bf026294>] (cpsw_remove+0x48/0x8c [ti_cpsw]) [ 51.597261] [<bf026294>] (cpsw_remove [ti_cpsw]) from [<c03e62c8>] (platform_drv_remove+0x18/0x1c) [ 51.606659] [<c03e62c8>] (platform_drv_remove) from [<c03e4c44>] (__device_release_driver+0x70/0xc8) [ 51.616237] [<c03e4c44>] (__device_release_driver) from [<c03e5458>] (driver_detach+0xb4/0xb8) [ 51.625264] [<c03e5458>] (driver_detach) from [<c03e4a6c>] (bus_remove_driver+0x4c/0x90) [ 51.633749] [<c03e4a6c>] (bus_remove_driver) from [<c00b024c>] (SyS_delete_module+0x10c/0x198) [ 51.642781] [<c00b024c>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48) Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14drivers: net: davinci_cpdma: remove kfree on objects allocated with devm_* apisMugunthan V N1-1/+0
memories allocated with devm_* apis must not be freed with kfree apis, so removing the kfree calls Fixes: e194312854ed ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().') Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14tg3: Add skb->xmit_more supportPrashant Sreedharan1-4/+6
Ring TX doorbell only if xmit_more is not set or the queue is stopped. Suggested-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Prashant Sreedharan <prashant@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/gigaset: fix usb_gigaset write_cmd result raceTilman Schmidt1-1/+3
In usb_gigaset function gigaset_write_cmd(), the length field of the command buffer structure could be cleared by the transmit tasklet before it was used for the function's return value. Fix by copying to a local variable before scheduling the tasklet. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/capi: don't return NULL from capi_cmd2str()Tilman Schmidt1-2/+7
capi_cmd2str() is used in many places to build log messages. None of them is prepared to handle NULL as a result. Change the function to return printable string "INVALID_COMMAND" instead. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/capi: handle CAPI 2.0 message parser failuresTilman Schmidt2-27/+145
Have callers of capi_cmsg2message and capi_message2cmsg handle non-zero return values indicating failure. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/capi: prevent NULL pointer dereference on invalid CAPI commandTilman Schmidt1-0/+7
An invalid CAPI 2.0 command/subcommand combination may retrieve a NULL pointer from the cpars[] array which will later be dereferenced by the parser routines. Fix by adding NULL pointer checks in strategic places. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/capi: refactor command/subcommand table accessesTilman Schmidt1-5/+18
Encapsulate accesses to the CAPI 2.0 command/subcommand name and parameter tables in a single place in preparation for redesign. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/capi: prevent index overrun from command_2_index()Tilman Schmidt1-0/+2
The result of the function command_2_index() is used to index two arrays mnames[] and cpars[] with max. index 0x4e but in its current form that function can produce results up to 3*(0x9+0x9)+0x7f = 0xb5. Fix by clamping all result values potentially overrunning the arrays to zero which is already handled as an invalid value. Re-spotted with Coverity. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/capi: correct capi20_manufacturer argument type mismatchTilman Schmidt1-2/+2
Function capi20_manufacturer() is declared with unsigned int cmd argument but called with unsigned long. Fix by correcting the function prototype since the actual argument is part of the user visible API. Spotted with Coverity. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/gigaset: fix non-heap pointer deallocationTilman Schmidt1-41/+70
at_state structures may be allocated individually or as part of a cardstate or bc_state structure. The disconnect() function handled both cases, creating a risk that it might try to deallocate an at_state structure that had not been allocated individually. Fix by splitting disconnect() into two variants handling cases with and without an associated B channel separately, and adding an explicit check. Spotted with Coverity. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/gigaset: fix NULL pointer dereferenceTilman Schmidt1-0/+5
In do_action, a NULL pointer might be passed to function start_dial which will dereference it. Fix by adding a check for NULL before the call. Spotted with Coverity. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/gigaset: limit raw CAPI message dump lengthTilman Schmidt1-0/+2
In dump_rawmsg, the length field from a received data package was used unscrutinized, allowing an attacker to control the size of the allocated buffer and the number of times the output loop iterates. Fix by limiting to a reasonable value. Spotted with Coverity. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/gigaset: make sure controller name is null terminatedTilman Schmidt1-2/+2
In gigaset_isdn_regdev, the name field may not have a null terminator if the source string's length is equal to the buffer size. Fix by zero filling the structure and excluding the last byte of the name field from the copy. Spotted with Coverity. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14isdn/gigaset: missing break in do_facility_reqTilman Schmidt1-0/+1
If we take the unsupported supplementary service notification mask path, we end up falling through and overwriting the error code. Insert a break statement to skip the remainder of the switch case and proceed to sending the reply message. Spotted with Coverity. Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: Tilman Schmidt <tilman@imap.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14net: fec: ptp: Enable PPS output based on ptp clockLuwei Zhou3-1/+205
FEC ptp timer has 4 channel compare/trigger function. It can be used to enable pps output. The pulse would be ouput high exactly on N second. The pulse ouput high on compare event mode is used to produce pulse per second. The pulse width would be one cycle based on ptp timer clock source.Since 31-bit ptp hardware timer is used, the timer will wrap more than 2 seconds. We need to reload the compare compare event about every 1 second. Signed-off-by: Luwei Zhou <b45643@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14net: fec: ptp: Use hardware algorithm to adjust PTP counter.Luwei Zhou2-12/+56
The FEC IP supports hardware adjustment for ptp timer. Refer to the description of ENET_ATCOR and ENET_ATINC registers in the spec about the hardware adjustment. This patch uses hardware support to adjust the ptp offset and frequency on the slave side. Signed-off-by: Luwei Zhou <b45643@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: Fugang Duan <b38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14net: fec: ptp: Use the 31-bit ptp timer.Luwei Zhou1-4/+6
When ptp switches from software adjustment to hardware ajustment, linux ptp can't converge. It is caused by the IP limit. Hardware adjustment logcial have issue when ptp counter runs over 0x80000000(31 bit counter). The internal IP reference manual already remove 32bit free-running count support. This patch replace the 32-bit PTP timer with 31-bit. Signed-off-by: Luwei Zhou <b45643@freescale.com> Signed-off-by: Frank Li <Frank.Li@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14fm10k: Add skb->xmit_more supportAlexander Duyck1-31/+34
This change adds support for skb->xmit_more based on the changes that were made to igb to support the feature. The main changes are moving up the check for maybe_stop_tx so that we can check netif_xmit_stopped to determine if we must write the tail because we can add no further buffers. Acked-by: Matthew Vick <matthew.vick@intel.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14net: fec: Fix sparse warnings with different lock contexts for basic blockNimrod Andy1-10/+14
reproduce: make ARCH=arm C=1 2>fec.txt drivers/net/ethernet/freescale/fec_main.o cat fec.txt sparse warnings: drivers/net/ethernet/freescale/fec_main.c:2916:12: warning: context imbalance in 'fec_set_features' - different lock contexts for basic block Christopher Li suggest to change as below: if (need_lock) { lock(); do_something_real(); unlock(); } else { do_something_real(); } Reported-by: Fabio Estevam <festevam@gmail.com> Suggested-by: Christopher Li <sparse@chrisli.org> Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-14phy/micrel: KSZ8031RNL RMII clock reconfiguration bugBruno Thomsen1-1/+3
Bug: Unable to send and receive Ethernet packets with Micrel PHY. Affected devices: KSZ8031RNL (commercial temp) KSZ8031RNLI (industrial temp) Description: PHY device is correctly detected during probe. PHY power-up default is 25MHz crystal clock input and output 50MHz RMII clock to MAC. Reconfiguration of PHY to input 50MHz RMII clock from MAC causes PHY to become unresponsive if clock source is changed after Operation Mode Strap Override (OMSO) register setup. Cause: Long lead times on parts where clock setup match circuit design forces the usage of similar parts with wrong default setup. Solution: Swapped KSZ8031 register setup and added phy_write return code validation. Tested with Freescale i.MX28 Fast Ethernet Controler (fec). Signed-off-by: Bruno Thomsen <bth@kamstrup.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10net: systemport: avoid unbalanced enable_irq_wake callsFlorian Fainelli1-1/+2
Multiple enable_irq_wake() calls will keep increasing the IRQ wake_depth, which ultimately leads to the following types of situation: 1) enable Wake-on-LAN interrupt w/o password 2) enable Wake-on-LAN interrupt w/ password 3) enable Wake-on-LAN interrupt w/o password 4) disable Wake-on-LAN interrupt After step 4), SYSTEMPORT would always wake-up the system no matter what wake-up device we use, which is not what we want. Fix this by making sure there are no unbalanced enable_irq_wake() calls. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10net: bcmgenet: avoid unbalanced enable_irq_wake callsFlorian Fainelli1-1/+3
Multiple enable_irq_wake() calls will keep increasing the IRQ wake_depth, which ultimately leads to the following types of situation: 1) enable Wake-on-LAN interrupt w/o password 2) enable Wake-on-LAN interrupt w/ password 3) enable Wake-on-LAN interrupt w/o password 4) disable Wake-on-LAN interrupt After step 4), GENET would always wake-up the system no matter what wake-up device we use, which is not what we want. Fix this by making sure there are no unbalanced enable_irq_wake() calls. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10net: bcmgenet: fix off-by-one in incrementing read pointerFlorian Fainelli1-5/+4
Commit b629be5c8399d7c423b92135eb43a86c924d1cbc ("net: bcmgenet: check harder for out of memory conditions") moved the increment of the local read pointer *before* reading from the hardware descriptor using dmadesc_get_length_status(), which creates an off-by-one situation. Fix this by moving again the read_ptr increment after we have read the hardware descriptor to get both the control block and the read pointer back in sync. Fixes: b629be5c8399 ("net: bcmgenet: check harder for out of memory conditions") Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Petri Gynther <pgynther@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10mlx4: fix race accessing page->_countEric Dumazet1-3/+3
This is illegal to use atomic_set(&page->_count, ...) even if we 'own' the page. Other entities in the kernel need to use get_page_unless_zero() to get a reference to the page before testing page properties, so we could loose a refcount increment. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10ixgbe: fix race accessing page->_countEric Dumazet1-5/+3
This is illegal to use atomic_set(&page->_count, 2) even if we 'own' the page. Other entities in the kernel need to use get_page_unless_zero() to get a reference to the page before testing page properties, so we could loose a refcount increment. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10igb: fix race accessing page->_countEric Dumazet1-4/+3
This is illegal to use atomic_set(&page->_count, 2) even if we 'own' the page. Other entities in the kernel need to use get_page_unless_zero() to get a reference to the page before testing page properties, so we could loose a refcount increment. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10fm10k: fix race accessing page->_countEric Dumazet1-4/+3
This is illegal to use atomic_set(&page->_count, 2) even if we 'own' the page. Other entities in the kernel need to use get_page_unless_zero() to get a reference to the page before testing page properties, so we could loose a refcount increment. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10net/phy: micrel: Add clock support for KSZ8021/KSZ8031Sascha Hauer1-2/+29
The KSZ8021 and KSZ8031 support RMII reference input clocks of 25MHz and 50MHz. Both PHYs differ in the default frequency they expect after reset. If this differs from the actual input clock, then register 0x1f bit 7 must be changed. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10macvlan: optimize the receive pathjbaron@akamai.com1-5/+10
The netif_rx() call on the fast path of macvlan_handle_frame() appears to be there to ensure that we properly throttle incoming packets. However, it would appear as though the proper throttling is already in place for all possible ingress paths, and that the call is redundant. If packets are arriving from the physical NIC, we've already throttled them by this point. Otherwise, if they are coming via macvlan_queue_xmit(), it calls either 'dev_forward_skb()', which ends up calling netif_rx_internal(), or else in the broadcast case, we are throttling via macvlan_broadcast_enqueue(). The test results below are from off the box to an lxc instance running macvlan. Once the tranactions/sec stop increasing, the cpu idle time has gone to 0. Results are from a quad core Intel E3-1270 V2@3.50GHz box with bnx2x 10G card. for i in {10,100,200,300,400,500}; do super_netperf $i -H $ip -t TCP_RR; done Average of 5 runs. trans/sec trans/sec (3.17-rc7-net-next) (3.17-rc7-net-next + this patch) ---------- ---------- 208101 211534 (+1.6%) 839493 850162 (+1.3%) 845071 844053 (-.12%) 816330 819623 (+.4%) 778700 789938 (+1.4%) 735984 754408 (+2.5%) Signed-off-by: Jason Baron <jbaron@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10macvlan: pass 'bool' type to macvlan_count_rx()jbaron@akamai.com1-3/+3
Pass last argument to macvlan_count_rx() as the correct bool type. Signed-off-by: Jason Baron <jbaron@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10drivers: net: xgene: Add 10GbE ethtool supportIyappan Subramanian1-6/+22
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Keyur Chudgar <kchudgar@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10drivers: net: xgene: Add 10GbE supportIyappan Subramanian6-30/+438
- Added 10GbE support - Removed unused macros/variables - Moved mac_init call to the end of hardware init Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Keyur Chudgar <kchudgar@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10drivers: net: xgene: Preparing for adding 10GbE supportIyappan Subramanian4-41/+78
- Rearranged code to pave the way for adding 10GbE support - Added mac_ops structure containing function pointers for mac specific functions - Added port_ops structure containing function pointers for port specific functions Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Keyur Chudgar <kchudgar@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10Merge tag 'master-2014-10-08' of ↵David S. Miller9-40/+67
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next John W. Linville says: ==================== pull request: wireless-next 2014-10-09 Please pull this batch of fixes intended for the 3.18 stream! Andrea Merello makes rtl818x_pci use a more reasonable transmission rate for HW generated frames. Fabian Frederick tweaks some kernel-doc bits to avoid warnings. Larry Finger corrects a possible unaligned access in the rtlwifi code. Marek Puzyniak avoids a kernel panic in ath9k_hw_reset. Sujith Manoharan goes for the hat trick -- he fixes a smatch warning in the shared ath code, he fixes a crash in ath9k, and he corrects a sequence number assignment problem in ath9k too. For ease of merging, I pulled the last bits of the wireless tree as well... Please let me know if there are problems! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10stmmac: correct mc_filter local variable in set_filter and set_mac_addr callVince Bridgers1-2/+2
Testing revealed that the local variable mc_filter was dimensioned incorrectly for all possible configurations and get_mac_addr should have been set_mac_addr (a typo). Make sure mc_filter is dimensioned to 8 32-bit unsigned longs - the largest size of the Synopsys multicast filter register set. Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-10-10net: pxa168_eth: PXA168_ETH should depend on HAS_DMAGeert Uytterhoeven1-1/+2
If NO_DMA=y: drivers/built-in.o: In function `rxq_deinit': pxa168_eth.c:(.text+0x2a2f2e): undefined reference to `dma_free_coherent' drivers/built-in.o: In function `txq_reclaim': pxa168_eth.c:(.text+0x2a3044): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `txq_deinit': pxa168_eth.c:(.text+0x2a310a): undefined reference to `dma_free_coherent' drivers/built-in.o: In function `txq_init': pxa168_eth.c:(.text+0x2a3226): undefined reference to `dma_alloc_coherent' drivers/built-in.o: In function `rxq_init': pxa168_eth.c:(.text+0x2a32d4): undefined reference to `dma_alloc_coherent' drivers/built-in.o: In function `init_hash_table': pxa168_eth.c:(.text+0x2a3354): undefined reference to `dma_alloc_coherent' drivers/built-in.o: In function `rxq_refill': pxa168_eth.c:(.text+0x2a345a): undefined reference to `dma_map_single' drivers/built-in.o: In function `rxq_process': pxa168_eth.c:(.text+0x2a39cc): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `pxa168_eth_remove': pxa168_eth.c:(.text+0x2a3b84): undefined reference to `dma_free_coherent' drivers/built-in.o: In function `pxa168_eth_start_xmit': pxa168_eth.c:(.text+0x2a3e8a): undefined reference to `dma_map_single' Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-09-19 17:54:24 +0300