summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2020-07-22net: phylink: update ethtool reporting for fixed-link modesRussell King1-0/+2
Comparing the ethtool output from phylink and non-phylink fixed-link setups shows that we have some differences: - The "auto-negotiation" fields are different; phylink reports these as "No", non-phylink reports these as "Yes" for the supported and advertising masks. - The link partner advertisement is set to the link speed with non- phylink, but phylink leaves this unset, causing all link partner fields to be omitted. The phylink ethtool output also disagrees with the software emulated PHY dump via the MII registers. Update the phylink fixed-link parsing code so that we better reflect the behaviour of the non-phylink code that this facility replaces, and bring the ethtool interface more into line with the report from via the MII interface. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22enetc: Add adaptive interrupt coalescingClaudiu Manoil4-7/+73
Use the generic dynamic interrupt moderation (dim) framework to implement adaptive interrupt coalescing on Rx. With the per-packet interrupt scheme, a high interrupt rate has been noted for moderate traffic flows leading to high CPU utilization. The 'dim' scheme implemented by the current patch addresses this issue improving CPU utilization while using minimal coalescing time thresholds in order to preserve a good latency. On the Tx side use an optimal time threshold value by default. This value has been optimized for Tx TCP streams at a rate of around 85kpps on a 1G link, at which rate half of the Tx ring size (128) gets filled in 1500 usecs. Scaling this down to 2.5G links yields the current value of 600 usecs, which is conservative and gives good enough results for 1G links too (see next). Below are some measurement results for before and after this patch (and related dependencies) basically, for a 2 ARM Cortex-A72 @1.3Ghz CPUs system (32 KB L1 data cache), using 60secs log netperf TCP stream tests @ 1Gbit link (maximum throughput): 1) 1 Rx TCP flow, both Rx and Tx processed by the same NAPI thread on the same CPU: CPU utilization int rate (ints/sec) Before: 50%-60% (over 50%) 92k After: 13%-22% 3.5k-12k Comment: Major CPU utilization improvement for a single flow Rx TCP flow (i.e. netperf -t TCP_MAERTS) on a single CPU. Usually settles under 16% for longer tests. 2) 4 Rx TCP flows + 4 Tx TCP flows (+ pings to check the latency): Total CPU utilization Total int rate (ints/sec) Before: ~80% (spikes to 90%) ~100k After: 60% (more steady) ~4k Comment: Important improvement for this load test, while the ping test outcome does not show any notable difference compared to before. Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22enetc: Add interrupt coalescing supportClaudiu Manoil4-10/+132
Enable programming of the interrupt coalescing registers and allow manual configuration of the coalescing time thresholds via ethtool. Packet thresholds have been fixed to predetermined values as there's no point in making them run-time configurable, also anticipating the dynamic interrupt moderation (DIM) algorithm which uses fixed packet thresholds as well. If the interface is up when the operation mode of traffic interrupt events is changed by the user (i.e. switching from default per-packet interrupts to coalesced interrupts), the traffic needs to be paused in the process. This patch also prepares the ground for introducing DIM on Rx. Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22enetc: Drop redundant ____cacheline_aligned_in_smpClaudiu Manoil1-1/+1
'struct enetc_bdr' is already '____cacheline_aligned_in_smp'. Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22enetc: Fix interrupt coalescing register namingClaudiu Manoil3-7/+7
Interrupt coalescing registers naming in the current revision of the Ref Man (RM) is ICR, deprecating the ICIR name used in earlier (draft) versions of the RM. Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22enetc: Factor out the traffic start/stop proceduresClaudiu Manoil1-25/+49
A reliable traffic pause (and reconfiguration) procedure is needed to be able to safely make h/w configuration changes during run-time, like changing the mode in which the interrupts are operating (i.e. with or without coalescing), as opposed to making on-the-fly register updates that may be subject to h/w or s/w concurrency issues. To this end, the code responsible of the run-time device configurations that basically starts resp. stops the traffic flow through the device has been extracted from the the enetc_open/_close procedures, to the separate standalone enetc_start/_stop procedures. Traffic stop should be as graceful as possible, it lets the executing napi threads to to finish while the interrupts stay disabled. But since the napi thread will try to re-enable interrupts by clearing the device's unmask register, the enable_irq/ disable_irq API has been used to avoid this potential concurrency issue and make the traffic pause procedure more reliable. Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22enetc: Refine buffer descriptor ring sizesClaudiu Manoil2-4/+5
It's time to differentiate between Rx and Tx ring sizes. Not only Tx rings are processed differently than Rx rings, but their default number also differs - i.e. up to 8 Tx rings per device (8 traffic classes) vs. 2 Rx rings (one per CPU). So let's set Tx rings sizes to half the size of the Rx rings for now, to be conservative. The default ring sizes were decreased as well (to the next lower power of 2), to reduce the memory footprint, buffering etc., since the measurements I've made so far show that the rings are very unlikely to get full. This change also anticipates the introduction of the dynamic interrupt moderation (dim) algorithm which operates on maximum packet thresholds of 256 packets for Rx and 128 packets for Tx. Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-22net: mdio-mux-gpio: use devm_gpiod_get_array()Jisheng Zhang1-8/+3
Use devm_gpiod_get_array() to simplify the error handling and exit code path. Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: dsa: qca8k: implement the port MTU callbacksJonathan McDowell2-0/+34
This switch has a single max frame size configuration register, so we track the requested MTU for each port and apply the largest. v2: - Address review feedback from Vladimir Oltean Signed-off-by: Jonathan McDowell <noodles@earth.li> Acked-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net/fealnx: switch from 'pci_' to 'dma_' APIChristophe JAILLET1-38/+53
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated, GFP_KERNEL can be used because it is called from the probe function (i.e. 'fealnx_init_one()') and no lock is taken. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21mISDN: switch from 'pci_' to 'dma_' APIChristophe JAILLET2-9/+11
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'setup_hw()' (hfcpci.c) GFP_KERNEL can be used because it is called from the probe function and no lock is taken. The call chain is: hfc_probe() --> setup_card() --> setup_hw() When memory is allocated in 'inittiger()' (netjet.c) GFP_ATOMIC must be used because a spin_lock is taken by the caller (i.e. 'nj_init_card()') This is also consistent with the other allocations done in the function. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21crypto/chtls: Enable tcp window scaling optionVinay Kumar Yadav1-0/+1
Enable tcp window scaling option in hw based on sysctl settings and option in connection request. v1->v2: - Set window scale option based on option in connection request. Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: add hwmon getter for MAC temperatureMark Starovoytov10-22/+215
This patch adds the possibility to obtain MAC temperature via hwmon. On A1 there are two separate temperature sensors. On A2 there's only one temperature sensor, which is used for reporting both MAC and PHY temperature. Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: A0 ntuple filtersDmitry Bogdanov1-28/+88
This patch adds support for ntuple filters on A0. Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: use intermediate variable to improve readability a bitNikita Danilov1-11/+10
This patch syncs up hw_atl_a0.c with an out-of-tree driver, where an intermediate variable was introduced in a couple of functions to improve the code readability a bit. Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: use U32_MAX in aq_hw_utils.cMark Starovoytov1-3/+2
This patch replaces magic constant ~0U usage with U32_MAX in aq_hw_utils.c Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: add support for 64-bit reads/writesPavel Belous6-8/+33
This patch adds support for 64-bit reads/writes where applicable, e.g. A2 supports them. Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: enable ipv6 support for TCP LSO and UDP GSOIgor Russkikh2-1/+2
This patch enables ipv6 support for TCP LSO and UDP GSO. The code itself (aq_nic_map_skb) was ready for this after udp gso feature, but corresponding NETIF_F_TSO6 wasn't enabled. We now have tested both tcp and udp v6 GSO, and enabling them safely. Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: PTP statisticsPavel Belous3-19/+105
This patch adds PTP rings statistics. Before that these were missing from overall stats, hardening debugging and analysis. Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: additional per-queue statsDmitry Bogdanov4-0/+23
This patch adds additional per-queue stats, these could be useful for debugging and diagnostics. Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: use u64_stats_update_* to protect access to 64-bit statsMark Starovoytov3-10/+47
This patch adds u64_stats_update_* usage to protect access to 64-bit stats, where necessary. This is necessary for per-ring stats, because they are updated by the driver directly, so there is a possibility for a partial read. Other stats require no additional protection, e.g.: * all MACSec stats are fetched directly from HW (under semaphore); * nic/ndev stats (aq_stats_s) are fetched directly from FW (under mutex). Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: split rx and tx per-queue statsMark Starovoytov6-63/+68
This patch splits rx and tx per-queue stats. This change simplifies the follow-up introduction of PTP stats and u64_stats_update_* usage. Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: make _get_sw_stats return count as return valueMark Starovoytov3-13/+9
This patch changes aq_vec_get_sw_stats() to return count as a return value (which was unused) instead of an out parameter. Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: use simple assignment in _get_stats and _get_sw_statsMark Starovoytov1-23/+24
This patch replaces addition assignment operator with a simple assignment in aq_vec_get_stats() and aq_vec_get_sw_stats(), because it is sufficient in both cases and this change simplifies the introduction of u64_stats_update_* in these functions. Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: atlantic: move FRAC_PER_NS to aq_hw.hMark Starovoytov2-11/+11
This patch moves FRAC_PER_NS to aq_hw.h so that it can be used in both hw_atl (A1) and hw_atl2 (A2) in the future. Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21ethernet: myri10ge: use generic power managementVaibhav Gupta1-29/+8
Drivers using legacy PM have to manage PCI states and device's PM states themselves. They also need to take care of configuration registers. With improved and powerful support of generic PM, PCI Core takes care of above mentioned, device-independent, jobs. This driver makes use of PCI helper functions like pci_save/restore_state(), pci_enable/disable_device(), pci_set_power_state() and pci_set_master() to do required operations. In generic mode, they are no longer needed. Change function parameter in both .suspend() and .resume() to "struct device*" type. Use to_pci_dev() and dev_get_drvdata() to get "struct pci_dev*" variable and drv data. Compile-tested only. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: add support for the extended speed and FEC modesAlexander Lobakin6-25/+546
Add all necessary code (NVM parsing, MFW and Ethtool reports etc.) to support extended speed and FEC modes. These new modes are supported by the new boards revisions and newer MFW versions. Misc: correct port type for MEDIA_KR. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: populate supported link modes maps on module initAlexander Lobakin1-71/+118
Simplify and lighten qed_set_link() by declaring static link modes maps and populating them on module init. This way we save plenty of text size at the low expense of __ro_after_init and __initconst data (the latter will be purged after module init is done). Misc: sanitize exit callback. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: add missing loopback modesAlexander Lobakin2-0/+24
These modes are relevant only for several boards, but may be reported by MFW as well as the others. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: add support for new port modesAlexander Lobakin2-0/+10
These ports ship on new boards revisions and are supported by newer firmware versions. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: remove unused qed_hw_info::port_mode and QED_PORT_MODEAlexander Lobakin2-36/+0
Struct field qed_hw_info::port_mode isn't used anywhere in the code, so can be safely removed to prevent possible dead code addition. Also remove the enumeration QED_PORT_MODE orphaned after this deletion. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: reformat several structures a bitAlexander Lobakin3-229/+237
Reformat a few nvm_cfg* structures (and partly qed_dev) prior to adding new fields and definitions. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qede: introduce support for FEC controlAlexander Lobakin1-0/+74
Add Ethtool callbacks for querying and setting FEC parameters if it's supported by the underlying qed module and MFW version running on the device. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qede: format qede{,_vf}_ethtool_opsAlexander Lobakin1-69/+68
Prior to adding new callbacks, format qede ethtool_ops structs to make declarations more fancy and readable. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: add support for Forward Error CorrectionAlexander Lobakin5-27/+108
Add all necessary routines for reading supported FEC modes from NVM and querying FEC control to the MFW (if the running version supports it). Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: reformat several structures a bitAlexander Lobakin2-169/+172
Prior to adding new fields and bitfields, reformat the related structures according to the Linux style (spaces to tabs, lowercase hex, indentation etc.). Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: use transceiver data to fill link partner's advertising speedsAlexander Lobakin1-20/+29
Currently qed driver does not take into consideration transceiver's capabilities when generating link partner's speed advertisement. This leads to e.g. incorrect ethtool link info on 10GbaseT modules. Use transceiver info not only for advertisement and support arrays, but also for link partner's abilities to fix it. Misc: fix a couple of comments nearby. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: add support for multi-rate transceiversAlexander Lobakin3-27/+106
Set the corresponding advertised and supported link modes according to the detected transceiver type and device capabilities. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed: reformat public_port::transceiver_data a bitAlexander Lobakin1-53/+55
Prior to adding new bitfields, reformat the existing ones from spaces to tabs, and unify all hex values to lowercase. Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qede: populate supported link modes maps on module initAlexander Lobakin3-54/+108
Simplify and lighten qede_set_link_ksettings() by declaring static link modes maps and populating them on module init. This way we save plenty of text size at the low expense of __ro_after_init and __initconst data (the latter will be purged after module init is done). Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21qed, qede, qedf: convert link mode from u32 to ETHTOOL_LINK_MODEAlexander Lobakin3-304/+262
Currently qed driver already ran out of 32 bits to store link modes, and this doesn't allow to add and support more speeds. Convert custom link mode to generic Ethtool bitmap and definitions (convenient Phylink shorthands are used for elegance and readability). This allowed us to drop all conversions/mappings between the driver and Ethtool. This involves changes in qede and qedf as well, as they used definitions from shared "qed_if.h". Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexander Lobakin <alobakin@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21Merge tag 'wireless-drivers-next-2020-07-20' of ↵David S. Miller130-690/+11824
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for v5.9 First set of patches for v5.9. This comes later than usual as I was offline for two weeks. The biggest change here is moving Microchip wilc1000 driver from staging. There was an immutable topic branch with one commit moving the whole driver and the topic branch was pulled both to staging-next and wireless-drivers-next. At the moment the only reported conflict is in MAINTAINERS file, so I'm hoping the move should go smoothly. Other notable changes are ath11k getting 6 GHz band support and rtw88 supporting RTL8821CE. And there's also the usual fixes, API changes and cleanups all over. Major changes: wilc1000 * move from drivers/staging to drivers/net/wireless/microchip ath11k * add 6G band support * add spectral scan support iwlwifi * make FW reconfiguration quieter by not using warn level rtw88 * add support for RTL8821CE ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21sis: switch from 'pci_' to 'dma_' APIChristophe JAILLET2-61/+80
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'epic_init_one()' (sis190.c), GFP_KERNEL can be used because this is a net_device_ops' 'ndo_open' function. This function is protected by the rtnl_lock() semaphore. So only a mutex is used and no spin_lock is acquired. When memory is allocated in 'sis900_probe()' (sis900.c), GFP_KERNEL can be used because it is a probe function and no spin_lock is acquired. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21r6040: switch from 'pci_' to 'dma_' APIChristophe JAILLET1-30/+34
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'r6040_open()', GFP_KERNEL can be used because this is a net_device_ops' 'ndo_open' function. This function is protected by the rtnl_lock() semaphore. So only a mutex is used and no spin_lock is acquired. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: packetengines: switch from 'pci_' to 'dma_' APIChristophe JAILLET2-84/+110
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'hamachi_init_one()' (hamachi.c), GFP_KERNEL can be used because it is a probe function and no lock is acquired. When memory is allocated in 'yellowfin_init_one()' (yellowfin.c), GFP_KERNEL can be used because it is a probe function and no lock is acquired. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: fs_enet: remove redundant null checkZhang Changzhong1-4/+2
Because clk_prepare_enable and clk_disable_unprepare already checked NULL clock parameter, so the additional checks are unnecessary, just remove them. Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: macb: Add WoL interrupt support for MACB type of Ethernet controllerNicolas Ferre1-1/+39
Handle the Wake-on-Lan interrupt for the Cadence MACB Ethernet controller. As we do for the GEM version, we handle of WoL interrupt in a specialized interrupt handler for MACB version that is positionned just between suspend() and resume() calls. Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: macb: WoL support for GEM type of Ethernet controllerNicolas Ferre2-27/+129
Adapt the Wake-on-Lan feature to the Cadence GEM Ethernet controller. This controller has different register layout and cannot be handled by previous code. We disable completely interrupts on all the queues but the queue 0. Handling of WoL interrupt is done in another interrupt handler positioned depending on the controller version used, just between suspend() and resume() calls. It allows to lower pressure on the generic interrupt hot path by removing the need to handle 2 tests for each IRQ: the first figuring out the controller revision, the second for actually knowing if the WoL bit is set. Queue management in suspend()/resume() functions inspired from RFC patch by Harini Katakam <harinik@xilinx.com>, thanks! Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: ena: Fix using plain integer as NULL pointer in ena_init_napi_in_rangeWang Hai1-3/+2
Fix sparse build warning: drivers/net/ethernet/amazon/ena/ena_netdev.c:2193:34: warning: Using plain integer as NULL pointer Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Suggested-by: Joe Perches <joe@perches.com> Acked-by: Shay Agroskin <shayagr@amazon.com> Acked-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-07-21net: hns: use eth_broadcast_addr() to assign broadcast addressXu Wang1-1/+1
This patch is to use eth_broadcast_addr() to assign broadcast address insetad of memset(). Signed-off-by: Xu Wang <vulab@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-09-02 03:28:41 +0300