| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add NAPI support to netdevim, similar to veth.
* Add a nsim_rq rx queue structure to hold a NAPI instance and a skb
queue.
* During xmit, store the skb in the peer skb queue and schedule NAPI.
* During napi_poll(), drain the skb queue and pass up the stack.
* Add assoc between rxq and NAPI instance using netif_queue_set_napi().
Signed-off-by: David Wei <dw@davidwei.uk>
Link: https://lore.kernel.org/r/20240507163228.2066817-2-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Various ndo_set_config() methods can change dev->if_port
dev->if_port is going to be read locklessly from
rtnl_fill_link_ifmap().
Add corresponding WRITE_ONCE() on writer sides.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240507184144.1230469-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the ipq806x dwmac driver is almost always used attached to the
CPU port of a switch and phy-mode was always set to "rgmii" or "sgmii".
Some device came up with a special configuration where the PHY is
directly attached to the GMAC port and in those case phy-mode needs to
be set to "rgmii-id" to make the PHY correctly work and receive packets.
Since the driver supports only "rgmii" and "sgmii" mode, when "rgmii-id"
(or variants) mode is set, the mode is rejected and probe fails.
Add support also for these phy-modes to correctly setup PHYs that requires
delay applied to tx/rx.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do
all needed initial configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8xxx variants
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches have different behavior on different ports:
- It seems to be not possible to disable VLAN PCP classification on port
2. It means, as soon as mutliqueue support is enabled, frames with
VLAN tag will get PCP prios. This behavior do not affect Port 1 -
it is possible to disable PCP prios.
- DSCP classification is not working on Port 2.
Since there are still usable configuration combinations, I added some
quirks to make sure user will get appropriate error message if not
possible configuration is chosen.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches support up to 4 queues. Rework ksz8795_set_prio_queue()
to support KSZ8795 and KSZ88X3 families of switches.
Per default, configure KSZ88X3 to use one queue, since it need special
handling due to priority related errata. Errata handling is implemented
in a separate patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-05-06 (ice)
This series contains updates to ice driver only.
Paul adds support for additional E830 devices and adjusts naming for
existing E830 devices.
Marcin commonizes a couple of TC setup calls to reduce duplicated code.
Mateusz adds ice_vsi_cfg_params into ice_vsi to consolidate info.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: refactor struct ice_vsi_cfg_params to be inside of struct ice_vsi
ice: Deduplicate tc action setup
ice: update E830 device ids and comments
ice: add additional E830 device ids
====================
Link: https://lore.kernel.org/r/20240506170827.948682-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: c9b37458e956 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506143939.3673865-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Link: https://lore.kernel.org/r/20240506142358.3657918-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some usb drivers try to set small skb->truesize and break
core networking stacks.
I replace one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c61172342 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f7a ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: 361459cd9642 ("net: usb: aqc111: Implement RX data path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506135546.3641185-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c94510 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The embedded PHYs of the 88E6250 family switches are very basic - they
do not even have an Extended Address / Page register.
This adds support for the PHYs to the driver to set up PHY interrupts
and retrieve error stats. To deal with PHYs without a page register,
"simple" variants of all stat handling functions are introduced.
The code should work with all 88E6250 family switches (6250/6220/6071/
6070/6020). The PHY ID 0x01410db0 was read from a 88E6020, under the
assumption that all switches of this family use the same ID. The spec
only lists the prefix 0x01410c00 and leaves the last 10 bits as reserved,
but that seems too unspecific to be useful, as it would cover several
existing PHY IDs already supported by the driver; therefore, the ID read
from the actual hardware is used.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/0695f699cd942e6e06da9d30daeedfd47785bc01.1714643285.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The list of stat registers is read-only, so we can declare it as const.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/24d7a2f39e0c4c94466e8ad43228fdd798053f3a.1714643285.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The rtnl lock is no longer needed to protect the control buffer and
command VQ.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Once the RTNL locking around the control buffer is removed there can be
contention on the per queue RX interrupt coalescing data. Use a mutex
per queue. A mutex is required because virtnet_send_command can sleep.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since we no longer have to hold the RTNL lock here just do updates for
the specified queue.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The command VQ will no longer be protected by the RTNL lock. Use a
mutex to protect the control buffer header and the VQ.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Allocate memory for the data when it's used. Ideally the struct could
be on the stack, but we can't DMA stack memory. With this change only
the header and status memory are shared between commands, which will
allow using a tighter lock than RTNL.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Stop storing RSS setting in the control buffer. This is prep work for
removing RTNL lock protection of the control buffer.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.
This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.
Since commit 91374ba537bd ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus"), we can describe the switch PHYs on the MDIO bus of
the switch on the device tree. Extend the check to detect PHY muxing when
the PHY is defined on the MDIO bus of the switch on the device tree.
When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240430-b4-for-netnext-mt7530-use-switch-mdio-bus-for-phy-muxing-v2-1-9104d886d0db@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.
All rtnl_link_ops->get_link_net() methods already using dev_net()
are ready. I added READ_ONCE() annotations on others.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When calling qede_flow_parse_ports(), then the
return code was only used for a non-zero check,
and then -EINVAL was returned.
qede_flow_parse_ports() can currently fail with:
* -EINVAL
This patch changes qede_flow_parse_v{4,6}_common() to
use the actual return code from qede_flow_parse_ports(),
so it's no longer assumed that all errors are -EINVAL.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When calling qede_flow_spec_validate_unused() then
the return code was only used for a non-zero check,
and then -EOPNOTSUPP was returned.
qede_flow_spec_validate_unused() can currently fail with:
* -EOPNOTSUPP
This patch changes qede_flow_spec_to_rule() to use the
actual return code from qede_flow_spec_validate_unused(),
so it's no longer assumed that all errors are -EOPNOTSUPP.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In qede_flow_spec_to_rule(), when calling
qede_parse_actions() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_actions() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
Commit 319a1d19471e ("flow_offload: check for
basic action hw stats type") broke the implicit
assumption that it could only fail with -EINVAL,
by changing it to return -EOPNOTSUPP, when hardware
stats are requested.
However AFAICT it's not possible to trigger
qede_parse_actions() to return -EOPNOTSUPP, when
called from qede_flow_spec_to_rule(), as hardware
stats can't be requested by ethtool_rx_flow_rule_create().
This patch changes qede_flow_spec_to_rule() to use
the actual return code from qede_parse_actions(),
so it's no longer assumed that all errors are -EINVAL.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According to GCC, the constriction of irq_name in otx2_open()
may, theoretically, be truncated.
This patch takes the approach of treating such a situation as an error
which it detects by making use of the return value of snprintf, which is
the total number of bytes, excluding the trailing '\0', that would have
been written.
Based on the approach taken to a similar problem in
commit 54b909436ede ("rtc: fix snprintf() checking in is_rtc_hctosys()")
Flagged by gcc-13 W=1 builds as:
.../otx2_pf.c:1933:58: warning: 'snprintf' output may be truncated before the last format character [-Wformat-truncation=]
1933 | snprintf(irq_name, NAME_SIZE, "%s-rxtx-%d", pf->netdev->name,
| ^
.../otx2_pf.c:1933:17: note: 'snprintf' output between 8 and 33 bytes into a destination of size 32
1933 | snprintf(irq_name, NAME_SIZE, "%s-rxtx-%d", pf->netdev->name,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
1934 | qidx);
| ~~~~~
Compile tested only.
Tested-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240503-octeon2-pf-irq_name-truncation-v2-1-91099177b942@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This list looks like it's been unused since the OF conversion in
2008 in
commit 826b6cfcd5d4 ("fore200e: Convert over to pure OF driver.")
This also means we can remove the 'entry' member for the list.
Build tested only.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/20240503001822.183061-1-linux@treblig.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The new netdev queue api is implemented for gve.
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Link: https://lore.kernel.org/all/20240501232549.1327174-11-shailend@google.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Refactor struct ice_vsi_cfg_params to be embedded into struct ice_vsi.
Prior to that the members of the struct were scattered around ice_vsi,
and were copy-pasted for purposes of reinit.
Now we have struct handy, and it is easier to have something sticky
in the flags field.
Suggested-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vaishnavi Tipireddy <vaishnavi.tipireddy@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_tc_setup_redirect_action() and ice_tc_setup_mirror_action() are almost
identical, except for setting filter action. Reduce them to one function
with an extra param, which handles both cases.
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Update existing E830 device ids and comments to align with new naming 'C'
for 100G and 'CC' for 200G.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add support for additional E830 device ids which are supported by the
driver:
- 0x12D5: Intel(R) Ethernet Controller E830-C for backplane
- 0x12D8: Intel(R) Ethernet Controller E830-C for QSFP
- 0x12DA: Intel(R) Ethernet Controller E830-C for SFP
- 0x12DC: Intel(R) Ethernet Controller E830-XXV for backplane
- 0x12DD: Intel(R) Ethernet Controller E830-XXV for QSFP
- 0x12DE: Intel(R) Ethernet Controller E830-XXV for SFP
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The PTP_CMD_CTL is a self clearing register which controls the PTP clock
values. In the current implementation driver waits for a duration of 20
sec in case of HW failure to clear the PTP_CMD_CTL register bit. This
timeout of 20 sec is very long to recognize a HW failure, as it is
typically cleared in one clock(<16ns). Hence reducing the timeout to 1 sec
would be sufficient to conclude if there is any HW failure observed. The
usleep_range will sleep somewhere between 1 msec to 20 msec for each
iteration. By setting the PTP_CMD_CTL_TIMEOUT_CNT to 50 the max timeout
is extended to 1 sec.
Signed-off-by: Rengarajan S <rengarajan.s@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240502050300.38689-1-rengarajan.s@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Every tx and rx ring has its own queue-page-list (QPL) that serves as
the bounce buffer. Previously we were allocating QPLs for all queues
before the queues themselves were allocated and later associating a QPL
with a queue. This is avoidable complexity: it is much more natural for
each queue to allocate and free its own QPL.
Moreover, the advent of new queue-manipulating ndo hooks make it hard to
keep things as is: we would need to transfer a QPL from an old queue to
a new queue, and that is unpleasant.
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We now account for the fact that the NIC might send us stats for a
subset of queues. Without this change, gve_get_ethtool_stats might make
an invalid access on the priv->stats_report->stats array.
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This does not fix any existing bug. In anticipation of the ndo queue api
hooks that alloc/free/start/stop a single Rx queue, the already existing
per-queue stop functions are being made more robust. Specifically for
this use case: rx_queue_n.stop() + rx_queue_n.start()
Note that this is not the use case being used in devmem tcp (the first
place these new ndo hooks would be used). There the usecase is:
new_queue.alloc() + old_queue.stop() + new_queue.start() + old_queue.free()
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to make possible the implementation of per-queue ndo hooks,
gve_turnup was changed in a previous patch to account for queues already
having some unprocessed descriptors: it does a one-off napi_schdule to
handle them. If conditions of consistent high traffic persist in the
immediate aftermath of this, the poll routine for a queue can be "stuck"
on the cpu on which the ndo hooks ran, instead of the cpu its irq has
affinity with.
This situation is exacerbated by the fact that the ndo hooks for all the
queues are invoked on the same cpu, potentially causing all the napi
poll routines to be residing on the same cpu.
A self correcting mechanism in the poll method itself solves this
problem.
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gVNIC has a requirement that all queues have to be quiesced before any
queue is operated on (created or destroyed). To enable the
implementation of future ndo hooks that work on a single queue, we need
to evolve gve_turnup to account for queues already having some
unprocessed descriptors in the ring.
Say rxq 4 is being stopped and started via the queue api. Due to gve's
requirement of quiescence, queues 0 through 3 are not processing their
rings while queue 4 is being toggled. Once they are made live, these
queues need to be poked to cause them to check their rings for
descriptors that were written during their brief period of quiescence.
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the queues are either all live or all dead, toggling from one
state to the other via the ndo open and stop hooks. The future addition
of single-queue ndo hooks changes this, and thus gve_turnup and
gve_turndown should evolve to account for a state where some queues are
live and some aren't.
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows for implementing future ndo hooks that act on a single
queue.
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although this is not fixing any existing double free bug, making these
functions idempotent allows for a simpler implementation of future ndo
hooks that act on a single queue.
Tested-by: Mina Almasry <almasrymina@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit a580ea994fd37f4105028f5a85c38ff6508a2b25.
This revert is to resolve Dragos's report of page_pool leak here:
https://lore.kernel.org/lkml/20240424165646.1625690-2-dtatulea@nvidia.com/
The reverted patch interacts very badly with commit 2cc3aeb5eccc ("skbuff:
Fix a potential race while recycling page_pool packets"). The reverted
commit hopes that the pp_recycle + is_pp_page variables do not change
between the skb_frag_ref and skb_frag_unref operation. If such a change
occurs, the skb_frag_ref/unref will not operate on the same reference type.
In the case of Dragos's report, the grabbed ref was a pp ref, but the unref
was a page ref, because the pp_recycle setting on the skb was changed.
Attempting to fix this issue on the fly is risky. Lets revert and I hope
to reland this with better understanding and testing to ensure we don't
regress some edge case while streamlining skb reffing.
Fixes: a580ea994fd3 ("net: mirror skb frag ref/unref helpers")
Reported-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Mina Almasry <almasrymina@google.com>
Link: https://lore.kernel.org/r/20240502175423.2456544-1-almasrymina@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current net-next/main does not boot for older chipsets e.g. Stratus.
Sample dmesg:
[ 11.368315] bnxt_en 0000:02:00.0 (unnamed net_device) (uninitialized): Able to reserve only 0 out of 9 requested RX rings
[ 11.390181] bnxt_en 0000:02:00.0 (unnamed net_device) (uninitialized): Unable to reserve tx rings
[ 11.438780] bnxt_en 0000:02:00.0 (unnamed net_device) (uninitialized): 2nd rings reservation failed.
[ 11.487559] bnxt_en 0000:02:00.0 (unnamed net_device) (uninitialized): Not enough rings available.
[ 11.506012] bnxt_en 0000:02:00.0: probe with driver bnxt_en failed with error -12
This is caused by bnxt_get_avail_msix() returning a negative value for
these chipsets not using the new resource manager i.e. !BNXT_NEW_RM.
This in turn causes hwr.cp in __bnxt_reserve_rings() to be set to 0.
In the current call stack, __bnxt_reserve_rings() is called from
bnxt_set_dflt_rings() before bnxt_init_int_mode(). Therefore,
bp->total_irqs is always 0 and for !BNXT_NEW_RM bnxt_get_avail_msix()
always returns a negative number.
Historically, MSIX vectors were requested by the RoCE driver during
run-time and bnxt_get_avail_msix() was used for this purpose. Today,
RoCE MSIX vectors are statically allocated. bnxt_get_avail_msix() should
only be called for the BNXT_NEW_RM() case to reserve the MSIX ahead of
time for RoCE use.
bnxt_get_avail_msix() is also be simplified to handle the BNXT_NEW_RM()
case only.
Fixes: d630624ebd70 ("bnxt_en: Utilize ulp client resources if RoCE is not registered")
Signed-off-by: David Wei <dw@davidwei.uk>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240502203757.3761827-1-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO
busses") mv88e6xxx_default_mdio_bus() has checked that the
return value of list_first_entry() is non-NULL.
This appears to be intended to guard against the list chip->mdios being
empty. However, it is not the correct check as the implementation of
list_first_entry is not designed to return NULL for empty lists.
Instead, use list_first_entry_or_null() which does return NULL if the
list is empty.
Flagged by Smatch.
Compile tested only.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430-mv88e6xx-list_empty-v3-1-c35c69d88d2e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct hfi1_netdev_rx by converting it
into a pointer. Then use the leverage alloc_netdev() to allocate the
net_device object at hfi1_alloc_rx().
[1] https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/
Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Leon Romanovsky <leon@kernel.org>
Link: https://lore.kernel.org/r/20240430162213.746492-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use flow_rule_is_supp_control_flags() to reject filters
with unsupported control flags.
In case any unsupported control flags are masked,
flow_rule_is_supp_control_flags() sets a NL extended
error message, and we return -EOPNOTSUPP.
Remove FLOW_DIS_FIRST_FRAG specific error message,
and treat it as any other unsupported control flag.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20240422152728.175677-1-ast@fiberby.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
