summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2012-06-12Merge branch 'master' of ↵John W. Linville163-5700/+10357
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
2012-06-12phy: Use pr_<level>Joe Perches7-36/+50
Use a more current logging style. Add pr_fmt and missing newlines. Remove embedded prefixes. Neaten phy_print_status to avoid using KERN_CONT. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-11ssb: add missing PCI ID for b/g/n single band BCM4322Jonas Gorski1-0/+1
14e4:432c is found on some bcm63xx devices. The device is working fine with b43. Reported-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11ath9k_hw: Initvals update for AR9462Sujith Manoharan1-0/+1
MSI is enabled by default for most of the 4th generation chips. Add this for AR9462 - this fixes PowerSave operation, the chip was not entering Network-Sleep mode earlier. With proper powering down of the MAC now, power consumption in associated state is reduced considerably. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11mwifiex: scan less channels per scan command to improve Tx trafficAmitkumar Karwar1-7/+27
Currently 4 channels are scanned per scan command. if scan request is issued by user during Tx traffic, radio will be out of channel for "4 * per_chan_scan_time" for each scan command and will not be able to receive Rx packets. This adds delay in data traffic. We can minimize it by reducing number of channels scanned per scan command in this scenario. We can not always scan 1 channel per scan command due to limitation of number of command buffers. So we add code to decide number of channels scanned per scan command in associated state. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11mwifiex: fix simultaneous scan and Tx traffic problemAmitkumar Karwar4-10/+89
If scan operation is started when Tx traffic is already running, driver locks Tx queue until it gets completed. With this logic there is a delay for Tx packets. This patch implements new approach to give Tx path higher priority in this case. Driver internally sends multiple synchronous scan commands to firmware when scan is requested by user. Now we will make sure that Tx queue is empty everytime before sending next scan command. If Tx queue isn't empty scan command will be postponsed by 20msec. This rule will be followed until Tx queue becomes empty or timeout of 1 second happens. In case of timeout scan operation will be aborted. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11mwifiex: shorten per channel scan timeBing Zhao1-3/+3
Currently the scan time per channel for active scanning is set to 200ms. It takes quite a while to finsh scanning on all channels, especially with a dual band configuration. Change the per channel scan time settings to the following values: passive scan: 110ms active scan: 30ms specific scan: 30ms Above settings have been tested on x86 and arm platforms. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-11Merge branch 'for-john' of ↵John W. Linville53-2553/+2329
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next Conflicts: drivers/net/wireless/iwlwifi/iwl-eeprom.c
2012-06-11Merge tag 'nfc-next-3.6-1' of ↵John W. Linville2-123/+549
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-3.0
2012-06-08wl18xx: avoid some -Wformat warningsJohn W. Linville1-1/+2
CC drivers/net/wireless/ti/wl18xx/main.o drivers/net/wireless/ti/wl18xx/main.c: In function ‘wl18xx_conf_init’: drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 2 has type ‘long unsigned int’ [-Wformat] drivers/net/wireless/ti/wl18xx/main.c:1024:3: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-08Merge branch 'wl12xx-next' into for-linvilleLuciano Coelho46-956/+4818
2012-06-08wlcore/wl12xx/wl18xx: make NVS file optional for wl18xxArik Nemtsov2-17/+9
Don't spew errors when we can't find the NVS file in wlcore. Instead fail the wl12xx boot HW op if the NVS isn't found. Take this opportunity to remove some dead code from register_hw() which looks for the NVS again needlessly. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wl18xx: clean up phy module parametersArik Nemtsov2-58/+56
Give all wl18xx phy module paramters -1 as a default value, indicating the paramter was not set. Add previous default values to the default 18xx priv conf structure. Remove the board_type field from wl18xx priv. The field with the same name inside the phy conf is good enough for our purposes. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wl18xx: align wl18xx_conf_phy with FW variant and remove itArik Nemtsov3-110/+36
wl18xx_conf_phy represents part of the FW native wl18xx_mac_and_phy_params structure. Remove it and replace the phy part of the wl18xx conf with the FW bound structure. This allows us to set/override all members. Increment the wlconf version to ensure compatibility with the new structure Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wl18xx: update fw statisticsIdo Reis2-24/+65
Aligned to the struct in FW 8.2.0.0.91 and updated the debugfs entries accordingly. Signed-off-by: Ido Reis <idor@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wl18xx: allow FW-log by default for PG2.0Arik Nemtsov1-1/+0
This is supported by new FW versions (.88+). Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wl18xx: read configuration structure from a binary fileLuciano Coelho1-5/+63
Instead of using the hardcoded configuration structure, try to read it from a "firmware" file called wl18xx-conf.bin. If the file doesn't exist, fall back to the hardcoded version. If the file exists but is illegal, bail out. Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wlcore/wl18xx: export conf struct in a debugfs fileLuciano Coelho3-0/+72
Add conf file header structure, magic and version values and export the entire conf struct in debugfs. Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wlcore/wl18xx: the conf structs must be packed so they can be exportedLuciano Coelho2-24/+24
Since we are now going to export the conf structure and read it from a file, it should be packed to avoid surprises with padding bytes. Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wlcore: use u8 instead of enum for bcn_filt_modeLuciano Coelho1-1/+1
Since we will export the conf structure as a file, we need to use well defined types. Instead of using enum, whose size may vary, use u8 for bcn_filt_mode instead. Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wlcore/wl18xx/wl12xx: use u8 instead of bool for host_fast_wakeup_supportLuciano Coelho3-4/+9
The conf structure is going to be exported to a file, so we should use only well defined types. bool is not well defined and may vary from platform to platform, so change the host_fast_wakeup_support type to u8 instead. Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wlcore: export raw binary with the FW statistics in debugfsLuciano Coelho1-0/+20
Instead of parsing all the binary data returned by the firmware, we should simply export the binary and let the userspace do the parsing. This commit adds a new file to debugfs to do that. Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wl18xx: add support to clear FW statisticsLuciano Coelho3-0/+63
This patch calls ACX_CLEAR_STATISTICS to clear the firmware statistics. The trigger is a new debugfs file called clear_fw_statistics in the fw_stats directory. Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wlcore: add debugfs control over rx interrupt pacingEyal Shapira1-0/+11
Add control over several conf fields which combined control the rx interrupt pacing mechanism, that is avoiding getting an interrupt following a single frame rx but instead have the FW trigger the interrupt only after a certain amount of frames received or a timeout. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08wlcore: add support macros to easily add conf debugfs entriesEyal Shapira1-0/+75
The current debugfs code contains too much code duplication of bolierplate code. Add some macro magic to avoid this and enable adding new debugfs entries by using just a few lines. Signed-off-by: Eyal Shapira <eyal@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-08be2net: Fix driver load for VFs for LancerPadmanabh Ratnakar3-61/+66
Permanent MAC is wrongly supplied in create iface command. Call the command with no MAC address and then MAC address should be later queried and applied. Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-08macvtap: use prepare_to_wait/finish_wait to ensure mbHong zhi guo1-5/+3
instead of raw assignment to current->state Signed-off-by: Hong Zhiguo <honkiko@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-08bnx2x: Added EEE Ethtool support.Yuval Mintz1-0/+134
This patch extends the bnx2x's ethtool interface to enable control in the eee feature, as well as report statistic information about it. Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-08bnx2x: Added EEE supportYuval Mintz7-10/+552
This patch adds energy efficient energy support (802.3az) to bnx2x boards with 84833 phys (and sufficiently new BC and external FW). Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-08qlcnic: Fix protcol type in case of inband vlan.Rajesh Borundia2-2/+3
o Use correct l3 (ETH_IP or ETH_IPV6)protcol in case of inband vlan. Because of incorrect protcol type driver was setting incorrect opcode. This resulted in adapter calculating checksum incorrectly. o Updated driver version to 5.0.29 Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-08qlcnic: fix unsupported CDRP command error message.Jitendra Kalsaria2-5/+33
Add debug messages for FW CDRP command failure. Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-08qlcnic: Fix estimation of recv MSS in case of LRORajesh Borundia5-0/+23
o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size. In case of LRO skb->len is aggregate of len of number of packets hence MSS obtained using skb->len would be incorrect. Incorrect estimation of recv MSS would lead to delayed acks in some traffic patterns (which sends two or three packets and wait for ack and only then send remaining packets). This leads to drop in performance. Hence we need to set gso_size to MSS obtained from firmware. o This is fixed recently in firmware hence the MSS is obtained based on capability. If fw is capable of sending the MSS then only driver sets the gso_size. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-08net/ethernet: ks8851_mll unregister_netdev() before freeingDan Carpenter1-1/+3
We added another error condition here, but if we were to hit it then we need to unregister_netdev() before doing the free_netdev(). Otherwise we would hit the BUG_ON() in free_netdev(): BUG_ON(dev->reg_state != NETREG_UNREGISTERED); Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-06-07wl12xx: Add support for an external 26 MHz crystal sourceGrant Erickson1-0/+1
Add support for an external 26 MHz crystal source. [Changed wl->ref_clock to priv->ref_clock -- Luca.] Signed-off-by: Grant Erickson <marathon96@gmail.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07wl18xx: pad only last frame in aggregration buffer for PG2Ido Reis7-9/+58
In PG2 only the last frame in the aggregate buffer should be aligned to the sdio block size. This frame's header msb should be set to 0, while in all the previous frames in the aggregation buffer, this bit should be set to 1. [Add a HW op for setting the frame ctrl bit only for 18xx. Other minor cleanups - Arik] [Make the pre_pkt_send operation optional -- Luca] Signed-off-by: Ido Reis <idor@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07wl18xx: PG2.0 HW Watch dog interrupt supportIdo Reis6-21/+71
In PG2, the HW watchdog interrupt occupies bit0 of the event vector, and the SW watchdog is relocated to bit9. We perform the relocation globally, as there's only one watchdog bit on previous platforms (bit0). [Only mask in the new bit9 for platforms supporting it. This avoids spurious events on other platforms - Arik] Signed-off-by: Orit Brayer <orit@ti.com> Signed-off-by: Ido Reis <idor@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07wl18xx: FW/PHY arguments added for PG2Ido Reis3-1/+28
PG2 requires 4 new parameters that to be passed to the PHY. Use the actual PHY initialization struct size for the mem size of the PHY_INIT section, to account for additions in params. [Make sure PG1 still gets the original struct - Arik] Signed-off-by: Ido Reis <idor@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07wl18xx: support PG2 version of the chipIdo Reis2-1/+12
PG2 has a unique chip id. It supports similar HW quirks. Signed-off-by: Ido Reis <idor@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07wl18xx: fix PHY_INIT addresses mem sizeIdo Reis1-2/+2
was hardcoded 252, now uses the parameters struct size. Signed-off-by: Ido Reis <idor@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-06-07can: c_can: Add support for Bosch D_CAN controllerAnilKumar Ch3-19/+94
This patch adds the support for D_CAN controller driver to the existing C_CAN driver. Bosch D_CAN controller is a full-CAN implementation which is compliant to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be obtained from: http://www.semiconductors.bosch.de/media/en/pdf/ ipmodules_1/can/d_can_users_manual_111.pdf A new array is added for accessing the d_can registers, according to d_can controller register space. Current D_CAN implementation has following limitations, this is done to avoid large changes to the C_CAN driver. 1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP supports upto 32 message objects but in case of D_CAN we can configure upto 128 message objects. 2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers. 3. These patches have been tested on little endian machine, there might be some hidden endian-related issues due to the nature of the accesses (32-bit registers accessed as 2 16-bit registers). However, I do not have a big-endian D_CAN implementation to confirm. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-07can: c_can: Move overlay structure to array with offset as indexAnilKumar Ch3-107/+154
c_can uses overlay structure for accessing c_can module registers. With this kind of implementation it is difficult to add one more ip which is similar to c_can in functionality but different register offsets. This patch changes the overlay structure implementation to an array with register offset as index. This way we can overcome the above limitation. Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2012-06-07Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller31-106/+186
2012-06-06wireless: update wireless URLsJohannes Berg1-1/+1
The preferred URL is http://wireless.kernel.org/ rather than http://linuxwireless.org/, update all URLs to point there. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06ath9k: Resync beacons properlySujith Manoharan1-2/+12
After a chip reset, the beacon timers have to re-programmed correctly for a station in associated state. Use the PS flags to ensure that this is done after a TSF sync happens, otherwise the driver ends up using incorrect values for TBTT/DTIM in powersave mode. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06ath9k: Fix powersave lockingSujith Manoharan3-9/+21
The 'ps_flags' is used/accessed in a variety of contexts and requires proper locking. Use 'sc_pm_lock' appropriately. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06ath9k: Handle fatal interrupts properlySujith Manoharan2-1/+7
When a fatal interrupt is received or it is detected that the baseband has hung, the chip has to be reset immediately. Otherwise, we end up processing spurious interrupts. Ensure that we bail out properly in the ISR when the reset work hasn't completed yet. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06ath9k: Use atomic operationsSujith Manoharan9-50/+52
The 'sc_flags' variable is being used in a number of places with no locking whatsoever. This patch converts the usage of sc_flags to atomic ops. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06ath9k: Move LNA code to antenna.cSujith Manoharan5-757/+786
And use a helper function to setup antennae after a reset. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06ath9k: Fix work handlingSujith Manoharan3-19/+37
* Currently, there is no synchronization between the reset work and the tx-poll work. Fix this and make sure that we bail out properly if a reset work is in progress. * Cleanup the PLL WAR and enable it for AR9340 too and use a helper for restarting work/timers after a reset. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-06-06ath9k: Group link monitoring logicSujith Manoharan5-479/+511
Add link.c and move all the link/connection monitoring code to it. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-10-15 18:10:40 +0300