Age | Commit message (Collapse) | Author | Files | Lines |
|
If PTP synchronisation is done every second, then sporadic the interval
is higher than one second:
ptp4l[696.582]: master offset -17 s2 freq -1891 path delay 573
ptp4l[697.582]: master offset -22 s2 freq -1901 path delay 573
ptp4l[699.368]: master offset -1 s2 freq -1887 path delay 573
^^^^^^^ Should be 698.582!
This problem is caused by rotten packets, which are received after
polling but before interrupts are enabled again. This can be fixed by
checking for pending work and rescheduling if necessary after interrupts
has been enabled again.
Fixes: 403f69bbdbad ("tsnep: Add TSN endpoint Ethernet MAC driver")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20221119211825.81805-1-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 4581dd480c9e ("net: octeontx2-pf: mcs: consider MACSEC setting")
has already added "depends on MACSEC || !MACSEC", so remove it.
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20221119133616.3583538-1-zhengbin13@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put(). Call pci_dev_put() before returning from
bnx2x_vf_is_pcie_pending() to avoid refcount leak.
Fixes: b56e9670ffa4 ("bnx2x: Prepare device and initialize VF database")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221119070202.1407648-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If phylink_of_phy_connect() fails, the port should be disabled.
If sparx5_serdes_set()/phy_power_on() fails, the port should be
disabled and the phylink should be stopped and disconnected.
Fixes: 946e7fd5053a ("net: sparx5: add port module support")
Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Tested-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Link: https://lore.kernel.org/r/20221117125918.203997-1-liujian56@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The __ef100_hard_start_xmit() returns NETDEV_TX_OK without freeing skb
in error handling case, add dev_kfree_skb_any() to fix it.
Fixes: 51b35a454efd ("sfc: skeleton EF100 PF driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/1668671409-10909-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
acpi_evaluate_dsm() should be coupled with ACPI_FREE() to free the ACPI
memory, because we need to track the allocation of acpi_object when
ACPI_DBG_TRACK_ALLOCATIONS enabled, so use ACPI_FREE() instead of kfree().
Fixes: d38a648d2d6c ("net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Link: https://lore.kernel.org/r/20221118062447.2324881-1-bobo.shaobowang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 1229b33973c7 ("ice: Add low latency Tx timestamp read") refactored
PTP timestamping logic to use a threaded IRQ instead of a separate kthread.
This implementation introduced ice_misc_intr_thread_fn and redefined the
ice_ptp_process_ts function interface to return a value of whether or not
the timestamp processing was complete.
ice_misc_intr_thread_fn would take the return value from ice_ptp_process_ts
and convert it into either IRQ_HANDLED if there were no more timestamps to
be processed, or IRQ_WAKE_THREAD if the thread should continue processing.
This is not correct, as the kernel does not re-schedule threaded IRQ
functions automatically. IRQ_WAKE_THREAD can only be used by the main IRQ
function.
This results in the ice_ptp_process_ts function (and in turn the
ice_ptp_tx_tstamp function) from only being called exactly once per
interrupt.
If an application sends a burst of Tx timestamps without waiting for a
response, the interrupt will trigger for the first timestamp. However,
later timestamps may not have arrived yet. This can result in dropped or
discarded timestamps. Worse, on E822 hardware this results in the interrupt
logic getting stuck such that no future interrupts will be triggered. The
result is complete loss of Tx timestamp functionality.
Fix this by modifying the ice_misc_intr_thread_fn to perform its own
polling of the ice_ptp_process_ts function. We sleep for a few microseconds
between attempts to avoid wasting significant CPU time. The value was
chosen to allow time for the Tx timestamps to complete without wasting so
much time that we overrun application wait budgets in the worst case.
The ice_ptp_process_ts function also currently returns false in the event
that the Tx tracker is not initialized. This would result in the threaded
IRQ handler never exiting if it gets started while the tracker is not
initialized.
Fix the function to appropriately return true when the tracker is not
initialized.
Note that this will not reproduce with default ptp4l behavior, as the
program always synchronously waits for a timestamp response before sending
another timestamp request.
Reported-by: Siddaraju DH <siddaraju.dh@intel.com>
Fixes: 1229b33973c7 ("ice: Add low latency Tx timestamp read")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20221118222729.1565317-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-11-18 (iavf)
Ivan Vecera resolves issues related to reset by adding back call to
netif_tx_stop_all_queues() and adding calls to dev_close() to ensure
device is properly closed during reset.
Stefan Assmann removes waiting for setting of MAC address as this breaks
ARP.
Slawomir adds setting of __IAVF_IN_REMOVE_TASK bit to prevent deadlock
between remove and shutdown.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: Fix race condition between iavf_shutdown and iavf_remove
iavf: remove INITIAL_MAC_SET to allow gARP to work properly
iavf: Do not restart Tx queues after reset task failure
iavf: Fix a crash during reset task
====================
Link: https://lore.kernel.org/r/20221118222439.1565245-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the ccr read error handling
case instead of 0, as done elsewhere in this function.
Fixes: 3265f4218878 ("net: phy: at803x: add fiber support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221118103635.254256-1-weiyongjun@huaweicloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This code accidentally uses the RX macro twice instead of the RX and TX.
Fixes: 6c635f78c474 ("octeontx2-af: cn10k: mcs: Handle MCS block interrupts")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function sparx5_tc_setup_qdisc_ets() always returns negative value
because it return -EOPNOTSUPP in the end. This patch returns the
rersult of sparx5_tc_ets_add() and sparx5_tc_ets_del() directly.
Fixes: 211225428d65 ("net: microchip: sparx5: add support for offloading ets qdisc")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
s3fwrn5_nci_send() won't free the skb when it failed for the check
before s3fwrn5_write(). As the result, the skb will memleak. Free the
skb when the check failed.
Fixes: c04c674fadeb ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nxp_nci_send() won't free the skb when it failed for the check before
write(). As the result, the skb will memleak. Free the skb when the
check failed.
Fixes: dece45855a8b ("NFC: nxp-nci: Add support for NXP NCI chips")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nfcmrvl_i2c_nci_send() will be called by nfcmrvl_nci_send(), and skb
should be freed in nfcmrvl_i2c_nci_send(). However, nfcmrvl_nci_send()
won't free the skb when it failed for the test_bit(). Free the skb when
test_bit() failed.
Fixes: b5b3e23e4cac ("NFC: nfcmrvl: add i2c driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Suggested-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'ret' is defined twice in macsec_changelink(), when it is set in macsec_is_offloaded
case, it will be invalid before return.
Fixes: 3cf3227a21d1 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/20221118011249.48112-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, we get icmp6hdr via function icmp6_hdr(), which needs the skb
transport header to be set first. But there is no rule to ask driver set
transport header before netif_receive_skb() and bond_handle_frame(). So
we will not able to get correct icmp6hdr on some drivers.
Fix this by using skb_header_pointer to get the IPv6 and ICMPV6 headers.
Reported-by: Liang Li <liali@redhat.com>
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20221118034353.1736727-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Setting of the port flag `NFP_PORT_CHANGED`, introduced
to ensure the correct reading of EEPROM data, causes a
fatal kernel NULL pointer dereference in cases where
the target netdev type cannot be determined.
Add validation of port struct pointer before attempting
to set the `NFP_PORT_CHANGED` flag. Return that operation
is not supported if the netdev type cannot be determined.
Fixes: 4ae97cae07e1 ("nfp: ethtool: fix the display error of `ethtool -m DEVNAME`")
Signed-off-by: Jaco Coetzee <jaco.coetzee@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The error is reflected in that it shows wrong splittable status of
port when executing "devlink port show".
The reason which leads the error is that the assigned operation of
splittable is just a simple negation operation of split and it does
not consider port lanes quantity. A splittable port should have
several lanes that can be split(lanes quantity > 1).
If without the judgement, it will show wrong message for some
firmware, such as 2x25G, 2x10G.
Fixes: a0f49b548652 ("devlink: Add a new devlink port split ability attribute and pass to netlink")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
In pch_gbe_probe(), pci_get_domain_bus_and_slot() is called,
so in error path in probe() and remove() function, pci_dev_put()
should be called to avoid refcount leak. Compile tested only.
Fixes: 1a0bdadb4e36 ("net/pch_gbe: supports eg20t ptp clock")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117135148.301014-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from rvu_dbg_rvu_pf_cgx_map_display() or
cgx_print_dmac_flt(), pci_dev_put() is called to avoid refcount
leak.
Fixes: dbc52debf95f ("octeontx2-af: Debugfs support for DMAC filters")
Fixes: e2fb37303865 ("octeontx2-af: Display CGX, NIX and PF map in debugfs.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221117124658.162409-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ql3xxx_send() returns NETDEV_TX_OK without freeing skb in error
handling case, add dev_kfree_skb_any() to fix it.
Fixes: bd36b0ac5d06 ("qla3xxx: Add support for Qlogic 4032 chip.")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1668675039-21138-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It will cause invalid pointer dereference to priv->cm3_base behind,
if PTR_ERR(priv->cm3_base) in mvpp2_get_sram().
Fixes: e54ad1e01c00 ("net: mvpp2: add CM3 SRAM memory map")
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Link: https://lore.kernel.org/r/20221117084032.101144-1-tanghui20@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If mlx4_bitmap_init fails, mlx4_bitmap_alloc_range will dereference
the NULL pointer (bitmap->table).
Make sure, that mlx4_bitmap_alloc_range called in no error case.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: d57febe1a478 ("net/mlx4: Add A0 hybrid steering")
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Peter Kosyh <pkosyh@yandex.ru>
Link: https://lore.kernel.org/r/20221117152806.278072-1-pkosyh@yandex.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If mtk_start_dma() fails, invoke phylink_disconnect_phy() to perform
cleanup. phylink_disconnect_phy() contains the put_device action. If
phylink_disconnect_phy is not performed, the Kref of netdev will leak.
Fixes: b8fc9f30821e ("net: ethernet: mediatek: Add basic PHYLINK support")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221117111356.161547-1-liujian56@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix a deadlock introduced by commit
974578017fc1 ("iavf: Add waiting so the port is initialized in remove")
due to race condition between iavf_shutdown and iavf_remove, where
iavf_remove stucks forever in while loop since iavf_shutdown already
set __IAVF_REMOVE adapter state.
Fix this by checking if the __IAVF_IN_REMOVE_TASK has already been
set and return if so.
Fixes: 974578017fc1 ("iavf: Add waiting so the port is initialized in remove")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
IAVF_FLAG_INITIAL_MAC_SET prevents waiting on iavf_is_mac_set_handled()
the first time the MAC is set. This breaks gratuitous ARP because the
MAC address has not been updated yet when the gARP packet is sent out.
Current behaviour:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: ee:04:19:14:ec:ea
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:23:41.676611 ee:04:19:14:ec:ea > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28
With IAVF_FLAG_INITIAL_MAC_SET removed:
$ echo 1 > /sys/class/net/ens4f0/device/sriov_numvfs
iavf 0000:88:02.0: MAC address: 3e:8a:16:a2:37:6d
$ ip addr add 192.168.1.1/24 dev ens4f0v0
$ ip link set dev ens4f0v0 up
$ echo 1 > /proc/sys/net/ipv4/conf/ens4f0v0/arp_notify
$ ip link set ens4f0v0 addr 00:11:22:33:44:55
07:28:01.836608 00:11:22:33:44:55 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.1, length 28
Fixes: 35a2443d0910 ("iavf: Add waiting for response from PF in set mac")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After commit aa626da947e9 ("iavf: Detach device during reset task")
the device is detached during reset task and re-attached at its end.
The problem occurs when reset task fails because Tx queues are
restarted during device re-attach and this leads later to a crash.
To resolve this issue properly close the net device in cause of
failure in reset task to avoid restarting of tx queues at the end.
Also replace the hacky manipulation with IFF_UP flag by device close
that clears properly both IFF_UP and __LINK_STATE_START flags.
In these case iavf_close() does not do anything because the adapter
state is already __IAVF_DOWN.
Reproducer:
1) Run some Tx traffic (e.g. iperf3) over iavf interface
2) Set VF trusted / untrusted in loop
[root@host ~]# cat repro.sh
PF=enp65s0f0
IF=${PF}v0
ip link set up $IF
ip addr add 192.168.0.2/24 dev $IF
sleep 1
iperf3 -c 192.168.0.1 -t 600 --logfile /dev/null &
sleep 2
while :; do
ip link set $PF vf 0 trust on
ip link set $PF vf 0 trust off
done
[root@host ~]# ./repro.sh
Result:
[ 2006.650969] iavf 0000:41:01.0: Failed to init adminq: -53
[ 2006.675662] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.689997] iavf 0000:41:01.0: Reset task did not complete, VF disabled
[ 2006.696611] iavf 0000:41:01.0: failed to allocate resources during reinit
[ 2006.703209] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.737011] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.764536] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.768919] BUG: kernel NULL pointer dereference, address: 0000000000000b4a
[ 2006.776358] #PF: supervisor read access in kernel mode
[ 2006.781488] #PF: error_code(0x0000) - not-present page
[ 2006.786620] PGD 0 P4D 0
[ 2006.789152] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 2006.792903] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.793501] CPU: 4 PID: 0 Comm: swapper/4 Kdump: loaded Not tainted 6.1.0-rc3+ #2
[ 2006.805668] Hardware name: Abacus electric, s.r.o. - servis@abacus.cz Super Server/H12SSW-iN, BIOS 2.4 04/13/2022
[ 2006.815915] RIP: 0010:iavf_xmit_frame_ring+0x96/0xf70 [iavf]
[ 2006.821028] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.821572] Code: 48 83 c1 04 48 c1 e1 04 48 01 f9 48 83 c0 10 6b 50 f8 55 c1 ea 14 45 8d 64 14 01 48 39 c8 75 eb 41 83 fc 07 0f 8f e9 08 00 00 <0f> b7 45 4a 0f b7 55 48 41 8d 74 24 05 31 c9 66 39 d0 0f 86 da 00
[ 2006.845181] RSP: 0018:ffffb253004bc9e8 EFLAGS: 00010293
[ 2006.850397] RAX: ffff9d154de45b00 RBX: ffff9d15497d52e8 RCX: ffff9d154de45b00
[ 2006.856327] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.857523] RDX: 0000000000000000 RSI: 00000000000005a8 RDI: ffff9d154de45ac0
[ 2006.857525] RBP: 0000000000000b00 R08: ffff9d159cb010ac R09: 0000000000000001
[ 2006.857526] R10: ffff9d154de45940 R11: 0000000000000000 R12: 0000000000000002
[ 2006.883600] R13: ffff9d1770838dc0 R14: 0000000000000000 R15: ffffffffc07b8380
[ 2006.885840] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.890725] FS: 0000000000000000(0000) GS:ffff9d248e900000(0000) knlGS:0000000000000000
[ 2006.890727] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2006.909419] CR2: 0000000000000b4a CR3: 0000000c39c10002 CR4: 0000000000770ee0
[ 2006.916543] PKRU: 55555554
[ 2006.918254] ice 0000:41:00.0: VF 0 is now trusted
[ 2006.919248] Call Trace:
[ 2006.919250] <IRQ>
[ 2006.919252] dev_hard_start_xmit+0x9e/0x1f0
[ 2006.932587] sch_direct_xmit+0xa0/0x370
[ 2006.936424] __dev_queue_xmit+0x7af/0xd00
[ 2006.940429] ip_finish_output2+0x26c/0x540
[ 2006.944519] ip_output+0x71/0x110
[ 2006.947831] ? __ip_finish_output+0x2b0/0x2b0
[ 2006.952180] __ip_queue_xmit+0x16d/0x400
[ 2006.952721] ice 0000:41:00.0: VF 0 is now untrusted
[ 2006.956098] __tcp_transmit_skb+0xa96/0xbf0
[ 2006.965148] __tcp_retransmit_skb+0x174/0x860
[ 2006.969499] ? cubictcp_cwnd_event+0x40/0x40
[ 2006.973769] tcp_retransmit_skb+0x14/0xb0
...
Fixes: aa626da947e9 ("iavf: Detach device during reset task")
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Patryk Piotrowski <patryk.piotrowski@intel.com>
Cc: SlawomirX Laba <slawomirx.laba@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Recent commit aa626da947e9 ("iavf: Detach device during reset task")
removed netif_tx_stop_all_queues() with an assumption that Tx queues
are already stopped by netif_device_detach() in the beginning of
reset task. This assumption is incorrect because during reset
task a potential link event can start Tx queues again.
Revert this change to fix this issue.
Reproducer:
1. Run some Tx traffic (e.g. iperf3) over iavf interface
2. Switch MTU of this interface in a loop
[root@host ~]# cat repro.sh
IF=enp2s0f0v0
iperf3 -c 192.168.0.1 -t 600 --logfile /dev/null &
sleep 2
while :; do
for i in 1280 1500 2000 900 ; do
ip link set $IF mtu $i
sleep 2
done
done
[root@host ~]# ./repro.sh
Result:
[ 306.199917] iavf 0000:02:02.0 enp2s0f0v0: NIC Link is Up Speed is 40 Gbps Full Duplex
[ 308.205944] iavf 0000:02:02.0 enp2s0f0v0: NIC Link is Up Speed is 40 Gbps Full Duplex
[ 310.103223] BUG: kernel NULL pointer dereference, address: 0000000000000008
[ 310.110179] #PF: supervisor write access in kernel mode
[ 310.115396] #PF: error_code(0x0002) - not-present page
[ 310.120526] PGD 0 P4D 0
[ 310.123057] Oops: 0002 [#1] PREEMPT SMP NOPTI
[ 310.127408] CPU: 24 PID: 183 Comm: kworker/u64:9 Kdump: loaded Not tainted 6.1.0-rc3+ #2
[ 310.135485] Hardware name: Abacus electric, s.r.o. - servis@abacus.cz Super Server/H12SSW-iN, BIOS 2.4 04/13/2022
[ 310.145728] Workqueue: iavf iavf_reset_task [iavf]
[ 310.150520] RIP: 0010:iavf_xmit_frame_ring+0xd1/0xf70 [iavf]
[ 310.156180] Code: d0 0f 86 da 00 00 00 83 e8 01 0f b7 fa 29 f8 01 c8 39 c6 0f 8f a0 08 00 00 48 8b 45 20 48 8d 14 92 bf 01 00 00 00 4c 8d 3c d0 <49> 89 5f 08 8b 43 70 66 41 89 7f 14 41 89 47 10 f6 83 82 00 00 00
[ 310.174918] RSP: 0018:ffffbb5f0082caa0 EFLAGS: 00010293
[ 310.180137] RAX: 0000000000000000 RBX: ffff92345471a6e8 RCX: 0000000000000200
[ 310.187259] RDX: 0000000000000000 RSI: 000000000000000d RDI: 0000000000000001
[ 310.194385] RBP: ffff92341d249000 R08: ffff92434987fcac R09: 0000000000000001
[ 310.201509] R10: 0000000011f683b9 R11: 0000000011f50641 R12: 0000000000000008
[ 310.208631] R13: ffff923447500000 R14: 0000000000000000 R15: 0000000000000000
[ 310.215756] FS: 0000000000000000(0000) GS:ffff92434ee00000(0000) knlGS:0000000000000000
[ 310.223835] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 310.229572] CR2: 0000000000000008 CR3: 0000000fbc210004 CR4: 0000000000770ee0
[ 310.236696] PKRU: 55555554
[ 310.239399] Call Trace:
[ 310.241844] <IRQ>
[ 310.243855] ? dst_alloc+0x5b/0xb0
[ 310.247260] dev_hard_start_xmit+0x9e/0x1f0
[ 310.251439] sch_direct_xmit+0xa0/0x370
[ 310.255276] __qdisc_run+0x13e/0x580
[ 310.258848] __dev_queue_xmit+0x431/0xd00
[ 310.262851] ? selinux_ip_postroute+0x147/0x3f0
[ 310.267377] ip_finish_output2+0x26c/0x540
Fixes: aa626da947e9 ("iavf: Detach device during reset task")
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Patryk Piotrowski <patryk.piotrowski@intel.com>
Cc: SlawomirX Laba <slawomirx.laba@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In pch_gbe_xmit_frame(), NETDEV_TX_OK will be returned whether
pch_gbe_tx_queue() sends data successfully or not, so pch_gbe_tx_queue()
needs to free skb before returning. But pch_gbe_tx_queue() returns without
freeing skb in case of dma_map_single() fails. Add dev_kfree_skb_any()
to fix it.
Fixes: 77555ee72282 ("net: Add Gigabit Ethernet driver of Topcliff PCH")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
You'd think people know that the internal 100BASE-TX PHY on the SJA1110
responds only to clause 22 MDIO transactions, but they don't :)
When a clause 45 transaction is attempted, sja1105_base_tx_mdio_read()
and sja1105_base_tx_mdio_write() don't expect "reg" to contain bit 30
set (MII_ADDR_C45) and pack this value into the SPI transaction buffer.
But the field in the SPI buffer has a width smaller than 30 bits, so we
see this confusing message from the packing() API rather than a proper
rejection of C45 transactions:
Call trace:
dump_stack+0x1c/0x38
sja1105_pack+0xbc/0xc0 [sja1105]
sja1105_xfer+0x114/0x2b0 [sja1105]
sja1105_xfer_u32+0x44/0xf4 [sja1105]
sja1105_base_tx_mdio_read+0x44/0x7c [sja1105]
mdiobus_read+0x44/0x80
get_phy_c45_ids+0x70/0x234
get_phy_device+0x68/0x15c
fwnode_mdiobus_register_phy+0x74/0x240
of_mdiobus_register+0x13c/0x380
sja1105_mdiobus_register+0x368/0x490 [sja1105]
sja1105_setup+0x94/0x119c [sja1105]
Cannot store 401d2405 inside bits 24-4 (would truncate)
Fixes: 5a8f09748ee7 ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently syzkaller discovered the issue of disappearing lower
device (NETDEV_UNREGISTER) while the virtual device (like
macvlan) is still having it as a lower device. So it's just
a matter of time similar discovery will be made for IPvlan
device setup. So fixing it preemptively. Also while at it,
add a refcount tracker.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the warning reported by kbuild:
cocci warnings: (new ones prefixed by >>)
>> drivers/net/ethernet/cavium/liquidio/lio_main.c:1797:54-56: WARNING !A || A && B is equivalent to !A || B
drivers/net/ethernet/cavium/liquidio/lio_main.c:1827:54-56: WARNING !A || A && B is equivalent to !A || B
Fixes: 8979f428a4af ("net: liquidio: release resources when liquidio driver open failed")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf.
Current release - regressions:
- tls: fix memory leak in tls_enc_skb() and tls_sw_fallback_init()
Previous releases - regressions:
- bridge: fix memory leaks when changing VLAN protocol
- dsa: make dsa_master_ioctl() see through port_hwtstamp_get() shims
- dsa: don't leak tagger-owned storage on switch driver unbind
- eth: mlxsw: avoid warnings when not offloaded FDB entry with IPv6
is removed
- eth: stmmac: ensure tx function is not running in
stmmac_xdp_release()
- eth: hns3: fix return value check bug of rx copybreak
Previous releases - always broken:
- kcm: close race conditions on sk_receive_queue
- bpf: fix alignment problem in bpf_prog_test_run_skb()
- bpf: fix writing offset in case of fault in
strncpy_from_kernel_nofault
- eth: macvlan: use built-in RCU list checking
- eth: marvell: add sleep time after enabling the loopback bit
- eth: octeon_ep: fix potential memory leak in octep_device_setup()
Misc:
- tcp: configurable source port perturb table size
- bpf: Convert BPF_DISPATCHER to use static_call() (not ftrace)"
* tag 'net-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (51 commits)
net: use struct_group to copy ip/ipv6 header addresses
net: usb: smsc95xx: fix external PHY reset
net: usb: qmi_wwan: add Telit 0x103a composition
netdevsim: Fix memory leak of nsim_dev->fa_cookie
tcp: configurable source port perturb table size
l2tp: Serialize access to sk_user_data with sk_callback_lock
net: thunderbolt: Fix error handling in tbnet_init()
net: microchip: sparx5: Fix potential null-ptr-deref in sparx_stats_init() and sparx5_start()
net: lan966x: Fix potential null-ptr-deref in lan966x_stats_init()
net: dsa: don't leak tagger-owned storage on switch driver unbind
net/x25: Fix skb leak in x25_lapb_receive_frame()
net: ag71xx: call phylink_disconnect_phy if ag71xx_hw_enable() fail in ag71xx_open()
bridge: switchdev: Fix memory leaks when changing VLAN protocol
net: hns3: fix setting incorrect phy link ksettings for firmware in resetting process
net: hns3: fix return value check bug of rx copybreak
net: hns3: fix incorrect hw rss hash type of rx packet
net: phy: marvell: add sleep time after enabling the loopback bit
net: ena: Fix error handling in ena_init()
kcm: close race conditions on sk_receive_queue
net: ionic: Fix error handling in ionic_init_module()
...
|
|
An external PHY needs settling time after power up or reset.
In the bind() function an mdio bus is registered. If at this point
the external PHY is still initialising, no valid PHY ID will be
read and on phy_find_first() the bind() function will fail.
If an external PHY is present, wait the maximum time specified
in 802.3 45.2.7.1.1.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221115114434.9991-2-alexandru.tachici@analog.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add the following Telit LE910C4-WWX composition:
0x103a: rmnet
Signed-off-by: Enrico Sau <enrico.sau@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20221115105859.14324-1-enrico.sau@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
kmemleak reports this issue:
unreferenced object 0xffff8881bac872d0 (size 8):
comm "sh", pid 58603, jiffies 4481524462 (age 68.065s)
hex dump (first 8 bytes):
04 00 00 00 de ad be ef ........
backtrace:
[<00000000c80b8577>] __kmalloc+0x49/0x150
[<000000005292b8c6>] nsim_dev_trap_fa_cookie_write+0xc1/0x210 [netdevsim]
[<0000000093d78e77>] full_proxy_write+0xf3/0x180
[<000000005a662c16>] vfs_write+0x1c5/0xaf0
[<000000007aabf84a>] ksys_write+0xed/0x1c0
[<000000005f1d2e47>] do_syscall_64+0x3b/0x90
[<000000006001c6ec>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
The issue occurs in the following scenarios:
nsim_dev_trap_fa_cookie_write()
kmalloc() fa_cookie
nsim_dev->fa_cookie = fa_cookie
..
nsim_drv_remove()
The fa_cookie allocked in nsim_dev_trap_fa_cookie_write() is not freed. To
fix, add kfree(nsim_dev->fa_cookie) to nsim_drv_remove().
Fixes: d3cbb907ae57 ("netdevsim: add ACL trap reporting cookie as a metadata")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Link: https://lore.kernel.org/r/1668504625-14698-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two trivial cleanups, and three simple fixes"
* tag 'for-linus-6.1-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/platform-pci: use define instead of literal number
xen/platform-pci: add missing free_irq() in error path
xen-pciback: Allow setting PCI_MSIX_FLAGS_MASKALL too
xen/pcpu: fix possible memory leak in register_pcpu()
x86/xen: Use kstrtobool() instead of strtobool()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Aere is a hopefully final round of pin control fixes. Nothing special,
driver fixes and we caught a potential NULL pointer exception.
- Fix a potential NULL dereference in the core!
- Fix all pin mux routes in the Rockchop PX30 driver
- Fix the UFS pins in the Qualcomm SC8280XP driver
- Fix bias disabling in the Mediatek driver
- Fix debounce time settings in the Mediatek driver"
* tag 'pinctrl-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: Export debounce time tables
pinctrl: mediatek: Fix EINT pins input debounce time configuration
pinctrl: devicetree: fix null pointer dereferencing in pinctrl_dt_to_map
pinctrl: mediatek: common-v2: Fix bias-disable for PULL_PU_PD_RSEL_TYPE
pinctrl: qcom: sc8280xp: Rectify UFS reset pins
pinctrl: rockchip: list all pins in a possible mux route for PX30
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Surface Pro 9 and Surface Laptop 5 kbd, battery, etc support (this
is just a few hw-id additions)
- A couple of other hw-id / DMI-quirk additions
- A few small bug fixes + 1 build fix
* tag 'platform-drivers-x86-v6.1-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: ideapad-laptop: Add module parameters to match DMI quirk tables
platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some Yoga laptops
platform/x86: hp-wmi: Ignore Smart Experience App event
platform/surface: aggregator_registry: Add support for Surface Laptop 5
platform/surface: aggregator_registry: Add support for Surface Pro 9
platform/surface: aggregator: Do not check for repeated unsequenced packets
platform/x86: acer-wmi: Enable SW_TABLET_MODE on Switch V 10 (SW5-017)
platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
platform/x86/intel: pmc: Don't unconditionally attach Intel PMC when virtualized
platform/x86: thinkpad_acpi: Enable s2idle quirk for 21A1 machine type
platform/x86/amd: pmc: Add new ACPI ID AMDI0009
platform/x86/amd: pmc: Remove more CONFIG_DEBUG_FS checks
|
|
A problem about insmod thunderbolt-net failed is triggered with following
log given while lsmod does not show thunderbolt_net:
insmod: ERROR: could not insert module thunderbolt-net.ko: File exists
The reason is that tbnet_init() returns tb_register_service_driver()
directly without checking its return value, if tb_register_service_driver()
failed, it returns without removing property directory, resulting the
property directory can never be created later.
tbnet_init()
tb_register_property_dir() # register property directory
tb_register_service_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without remove property directory
Fix by remove property directory when tb_register_service_driver() returns
error.
Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
and sparx5_start()
sparx_stats_init() calls create_singlethread_workqueue() and not
checked the ret value, which may return NULL. And a null-ptr-deref may
happen:
sparx_stats_init()
create_singlethread_workqueue() # failed, sparx5->stats_queue is NULL
queue_delayed_work()
queue_delayed_work_on()
__queue_delayed_work() # warning here, but continue
__queue_work() # access wq->flags, null-ptr-deref
Check the ret value and return -ENOMEM if it is NULL. So as
sparx5_start().
Fixes: af4b11022e2d ("net: sparx5: add ethtool configuration and statistics support")
Fixes: b37a1bae742f ("net: sparx5: add mactable support")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lan966x_stats_init() calls create_singlethread_workqueue() and not
checked the ret value, which may return NULL. And a null-ptr-deref may
happen:
lan966x_stats_init()
create_singlethread_workqueue() # failed, lan966x->stats_queue is NULL
queue_delayed_work()
queue_delayed_work_on()
__queue_delayed_work() # warning here, but continue
__queue_work() # access wq->flags, null-ptr-deref
Check the ret value and return -ENOMEM if it is NULL.
Fixes: 12c2d0a5b8e2 ("net: lan966x: add ethtool configuration and statistics")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add module parameters to allow setting the hw_rfkill_switch and
set_fn_lock_led feature flags for testing these on laptops which are not
on the DMI-id based allow lists for these 2 flags.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221115193400.376159-1-hdegoede@redhat.com
|
|
Yoga laptops
Commit 3ae86d2d4704 ("platform/x86: ideapad-laptop: Fix Legion 5 Fn lock
LED") uses the WMI event-id for the fn-lock event on some Legion 5 laptops
to manually toggle the fn-lock LED because the EC does not do it itself.
However, the same WMI ID is also sent on some Yoga laptops. Here, setting
the fn-lock state is not valid behavior, and causes the EC to spam
interrupts until the laptop is rebooted.
Add a set_fn_lock_led_list[] DMI-id list and only enable the workaround to
manually set the LED on models on this list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=212671
Cc: Meng Dong <whenov@gmail.com>
Signed-off-by: Arnav Rawat <arnavr3@illinois.edu>
Link: https://lore.kernel.org/r/12093851.O9o76ZdvQC@fedora
[hdegoede@redhat.com: Check DMI-id list only once and store the result]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Sometimes hp-wmi driver complains on system resume:
[ 483.116451] hp_wmi: Unknown event_id - 33 - 0x0
According to HP it's a feature called "HP Smart Experience App" and it's
safe to be ignored.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20221114073842.205392-1-kai.heng.feng@canonical.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal HID devices (including
touchpad and keyboard) on the Surface Laptop 5.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221115231440.1338142-1-luzmaximilian@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
ag71xx_open()
If ag71xx_hw_enable() fails, call phylink_disconnect_phy() to clean up.
And if phylink_of_phy_connect() fails, nothing needs to be done.
Compile tested only.
Fixes: 892e09153fa3 ("net: ag71xx: port to phylink")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221114095549.40342-1-liujian56@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal and type-cover HID devices
(including sensors, touchpad, keyboard, and other miscellaneous devices)
on the Surface Pro 9.
This does not include support for a tablet-mode switch yet, as that is
now handled via the POS subsystem (unlike the Surface Pro 8, where it is
handled via the KIP subsystem) and therefore needs further changes.
While we're at it, also add the missing comment for the Surface Pro 8.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Currently, we check any received packet whether we have already seen it
previously, regardless of the packet type (sequenced / unsequenced). We
do this by checking the sequence number. This assumes that sequence
numbers are valid for both sequenced and unsequenced packets. However,
this assumption appears to be incorrect.
On some devices, the sequence number field of unsequenced packets (in
particular HID input events on the Surface Pro 9) is always zero. As a
result, the current retransmission check kicks in and discards all but
the first unsequenced packet, breaking (among other things) keyboard and
touchpad input.
Note that we have, so far, only seen packets being retransmitted in
sequenced communication. In particular, this happens when there is an
ACK timeout, causing the EC (or us) to re-send the packet waiting for an
ACK. Arguably, retransmission / duplication of unsequenced packets
should not be an issue as there is no logical condition (such as an ACK
timeout) to determine when a packet should be sent again.
Therefore, remove the retransmission check for unsequenced packets
entirely to resolve the issue.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-1-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Like the Acer Switch 10 (SW5-012) and Acer Switch 10 (S1003) models
the Acer Switch V 10 (SW5-017) supports reporting SW_TABLET_MODE
through acer-wmi.
Add a DMI quirk for the SW5-017 setting force_caps to ACER_CAP_KBD_DOCK
(these devices have no other acer-wmi based functionality).
Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221111111639.35730-1-hdegoede@redhat.com
|