summaryrefslogtreecommitdiff
path: root/include/linux/ath9k_platform.h
AgeCommit message (Collapse)AuthorFilesLines
2012-12-11ath9k: allow to load EEPROM content via firmware APIGabor Juhos1-0/+2
The calibration data for devices w/o a separate EEPROM chip can be specified via the 'eeprom_data' field of 'ath9k_platform_data'. The 'eeprom_data' is usually filled from board specific setup functions. It is easy if the EEPROM data is mapped to the memory, but it can be complicated if it is stored elsewhere. The patch adds support for loading of the EEPROM data via the firmware API to avoid this limitation. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-23ath9k: add external_reset callback to ath9k_platfom_data for AR9330Gabor Juhos1-0/+1
The patch adds a callback to ath9k_platform_data. If the callback is provided by the platform code, then it can be used to hard reset the WMAC device. The callback is required for doing a hard reset of the AR9330 chips to get them working again after a hang. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-23ath9k: add MAC revision detection for AR9330Gabor Juhos1-0/+1
The AR9330 1.0 and 1.1 are using the same revision, thus it is not possible to distinguish the two chips. The platform setup code can distinguish the chips based on the SoC revision. Add a callback function to ath9k_platform_data in order to allow getting the revision number from the platform code. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-25ath9k_hw: Get AHB clock information from ath9k_platform_dataVasanthakumar Thiagarajan1-0/+2
Add a bool in ath9k_platform_data to pass AHB clock speed information. Driver needs this to configure PLL on some SOCs. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-30ath9k: add support for overriding LED pin and GPIO settings from platform dataFelix Fietkau1-0/+4
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-30ath9k: add support for overriding the MAC address through platform dataFelix Fietkau1-0/+1
On some devices the correct MAC address is not in the EEPROM data, but stored somewhere else. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-30ath9k: get EEPROM contents from platform data on AHB busGabor Juhos1-0/+28
On the AR913x SOCs we have to provide EEPROM contents via platform_data, because accessing the flash via MMIO is not safe. Additionally different boards may store the radio calibration data at different locations. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>