summaryrefslogtreecommitdiff
path: root/include/linux/ktime.h
AgeCommit message (Collapse)AuthorFilesLines
2017-10-31time: Move old timekeeping interfaces to timekeeping32.hArnd Bergmann1-0/+1
The interfaces based on 'struct timespec' and 'unsigned long' seconds are no longer recommended for new code, and we are trying to migrate to ktime_t based interfaces and other y2038-safe variants. This moves all the legacy interfaces from linux/timekeeping.h into a new timekeeping32.h to better document this. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: John Stultz <john.stultz@linaro.org>
2016-12-25ktime: Get rid of ktime_equal()Thomas Gleixner1-15/+0
No point in going through loops and hoops instead of just comparing the values. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org>
2016-12-25ktime: Get rid of the unionThomas Gleixner1-45/+23
ktime is a union because the initial implementation stored the time in scalar nanoseconds on 64 bit machine and in a endianess optimized timespec variant for 32bit machines. The Y2038 cleanup removed the timespec variant and switched everything to scalar nanoseconds. The union remained, but become completely pointless. Get rid of the union and just keep ktime_t as simple typedef of type s64. The conversion was done with coccinelle and some manual mopping up. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org>
2016-10-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds1-0/+5
Pull networking updates from David Miller: 1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and co. at Google. https://lwn.net/Articles/701165/ 2) Do TCP Small Queues for retransmits, from Eric Dumazet. 3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei Starovoitov. 4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai. 5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn. 6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker. 7) Support ndo_poll_controller in mlx5, from Calvin Owens. 8) Move VRF processing to an output hook and allow l3mdev to be loopback, from David Ahern. 9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern. 10) Congestion control in RXRPC, from David Howells. 11) Support geneve RX offload in ixgbe, from Emil Tantilov. 12) When hitting pressure for new incoming TCP data SKBs, perform a partial rathern than a full purge of the OFO queue (which could be huge). From Eric Dumazet. 13) Convert XFRM state and policy lookups to RCU, from Florian Westphal. 14) Support RX network flow classification to igb, from Gangfeng Huang. 15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski. 16) New skbmod packet action, from Jamal Hadi Salim. 17) Remove some inefficiencies in snmp proc output, from Jia He. 18) Add FIB notifications to properly propagate route changes to hardware which is doing forwarding offloading. From Jiri Pirko. 19) New dsa driver for qca8xxx chips, from John Crispin. 20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej Żenczykowski. 21) Add L3 mode to ipvlan, from Mahesh Bandewar. 22) Support 802.1ad in mlx4, from Moshe Shemesh. 23) Support hardware LRO in mediatek driver, from Nelson Chang. 24) Add TC offloading to mlx5, from Or Gerlitz. 25) Convert various drivers to ethtool ksettings interfaces, from Philippe Reynes. 26) TX max rate limiting for cxgb4, from Rahul Lakkireddy. 27) NAPI support for ath10k, from Rajkumar Manoharan. 28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed. 29) UDP replicast support in TIPC, from Richard Alpe. 30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru. 31) Support BQL in thunderx driver, from Sunil Goutham. 32) TSO support in alx driver, from Tobias Regnery. 33) Add stream parser engine and use it in kcm. 34) Support async DHCP replies in ipconfig module, from Uwe Kleine-König. 35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits) mlxsw: switchx2: Fix misuse of hard_header_len mlxsw: spectrum: Fix misuse of hard_header_len net/faraday: Stop NCSI device on shutdown net/ncsi: Introduce ncsi_stop_dev() net/ncsi: Rework the channel monitoring net/ncsi: Allow to extend NCSI request properties net/ncsi: Rework request index allocation net/ncsi: Don't probe on the reserved channel ID (0x1f) net/ncsi: Introduce NCSI_RESERVED_CHANNEL net/ncsi: Avoid unused-value build warning from ia64-linux-gcc net: Add netdev all_adj_list refcnt propagation to fix panic net: phy: Add Edge-rate driver for Microsemi PHYs. vmxnet3: Wake queue from reset work i40e: avoid NULL pointer dereference and recursive errors on early PCI error qed: Add RoCE ll2 & GSI support qed: Add support for memory registeration verbs qed: Add support for QP verbs qed: PD,PKEY and CQ verb support qed: Add support for RoCE hw init qede: Add qedr framework ...
2016-09-22rxrpc: Add ktime_sub_ms()David Howells1-0/+5
Add a ktime_sub_ms() to go with ktime_add_ms() and co. for use in AF_RXRPC RTT determination. Signed-off-by: David Howells <dhowells@redhat.com>
2016-09-01time: Avoid undefined behaviour in ktime_add_safe()Vegard Nossum1-0/+7
I ran into this: ================================================================================ UBSAN: Undefined behaviour in kernel/time/hrtimer.c:310:16 signed integer overflow: 9223372036854775807 + 50000 cannot be represented in type 'long long int' CPU: 2 PID: 4798 Comm: trinity-c2 Not tainted 4.8.0-rc1+ #91 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014 0000000000000000 ffff88010ce6fb88 ffffffff82344740 0000000041b58ab3 ffffffff84f97a20 ffffffff82344694 ffff88010ce6fbb0 ffff88010ce6fb60 000000000000c350 ffff88010ce6f968 dffffc0000000000 ffffffff857bc320 Call Trace: [<ffffffff82344740>] dump_stack+0xac/0xfc [<ffffffff82344694>] ? _atomic_dec_and_lock+0xc4/0xc4 [<ffffffff8242df78>] ubsan_epilogue+0xd/0x8a [<ffffffff8242e6b4>] handle_overflow+0x202/0x23d [<ffffffff8242e4b2>] ? val_to_string.constprop.6+0x11e/0x11e [<ffffffff8236df71>] ? timerqueue_add+0x151/0x410 [<ffffffff81485c48>] ? hrtimer_start_range_ns+0x3b8/0x1380 [<ffffffff81795631>] ? memset+0x31/0x40 [<ffffffff8242e6fd>] __ubsan_handle_add_overflow+0xe/0x10 [<ffffffff81488ac9>] hrtimer_nanosleep+0x5d9/0x790 [<ffffffff814884f0>] ? hrtimer_init_sleeper+0x80/0x80 [<ffffffff813a9ffb>] ? __might_sleep+0x5b/0x260 [<ffffffff8148be10>] common_nsleep+0x20/0x30 [<ffffffff814906c7>] SyS_clock_nanosleep+0x197/0x210 [<ffffffff81490530>] ? SyS_clock_getres+0x150/0x150 [<ffffffff823c7113>] ? __this_cpu_preempt_check+0x13/0x20 [<ffffffff8162ef60>] ? __context_tracking_exit.part.3+0x30/0x1b0 [<ffffffff81490530>] ? SyS_clock_getres+0x150/0x150 [<ffffffff81007bd3>] do_syscall_64+0x1b3/0x4b0 [<ffffffff845f85aa>] entry_SYSCALL64_slow_path+0x25/0x25 ================================================================================ Add a new ktime_add_unsafe() helper which doesn't check for overflow, but doesn't throw a UBSAN warning when it does overflow either. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: John Stultz <john.stultz@linaro.org>
2015-05-13ktime: Fix ktime_divns to do signed divisionJohn Stultz1-6/+21
It was noted that the 32bit implementation of ktime_divns() was doing unsigned division and didn't properly handle negative values. And when a ktime helper was changed to utilize ktime_divns, it caused a regression on some IR blasters. See the following bugzilla for details: https://bugzilla.redhat.com/show_bug.cgi?id=1200353 This patch fixes the problem in ktime_divns by checking and preserving the sign bit, and then reapplying it if appropriate after the division, it also changes the return type to a s64 to make it more obvious this is expected. Nicolas also pointed out that negative dividers would cause infinite loops on 32bit systems, negative dividers is unlikely for users of this function, but out of caution this patch adds checks for negative dividers for both 32-bit (BUG_ON) and 64-bit(WARN_ON) versions to make sure no such use cases creep in. [ tglx: Hand an u64 to do_div() to avoid the compiler warning ] Fixes: 166afb64511e 'ktime: Sanitize ktime_to_us/ms conversion' Reported-and-tested-by: Trevor Cordes <trevor@tecnopolis.ca> Signed-off-by: John Stultz <john.stultz@linaro.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Josh Boyer <jwboyer@redhat.com> Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/1431118043-23452-1-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2015-01-24Merge tag 'fortglx-3.20-time' of ↵Thomas Gleixner1-1/+11
https://git.linaro.org/people/john.stultz/linux into timers/core Pull time updates from John Stultz for 3.20: * ktime division optimization * Expose a few more y2038-safe timekeeping interfaces * RTC core changes to address y2038
2015-01-24ktime: Optimize ktime_divns for constant divisorsNicolas Pitre1-1/+11
At least on ARM, do_div() is optimized to turn constant divisors into an inline multiplication by the reciprocal value at compile time. However this optimization is missed entirely whenever ktime_divns() is used and the slow out-of-line division code is used all the time. Let ktime_divns() use do_div() inline whenever the divisor is constant and small enough. This will make things like ktime_to_us() and ktime_to_ms() much faster. Cc: Arnd Bergmann <arnd.bergmann@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Nicolas Pitre <nico@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: John Stultz <john.stultz@linaro.org>
2015-01-23ktime.h: Introduce ktime_ms_deltaChunyan Zhang1-0/+5
This patch adds a reusable time difference function which returns the difference in millisecond, as often used in some driver code, e.g. mtd/test, media/rc, etc. Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org> Acked-by: Arnd Bergmann <arnd@linaro.org> Cc: zhang.lyra@gmail.com Cc: davem@davemloft.net Cc: john.stultz@linaro.org Cc: dborkman@redhat.com Link: http://lkml.kernel.org/r/1418793095-18780-1-git-send-email-zhang.chunyan@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2014-07-23time: Consolidate the time accessor prototypesThomas Gleixner1-6/+2
Right now we have time related prototypes in 3 different header files. Move it to a single timekeeping header file and move the core internal stuff into a core private header. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org>
2014-07-23time: More core infrastructure for timespec64John Stultz1-0/+28
Helper and conversion functions for timespec64. Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org>
2014-07-23ktime: Change ktime_set() to take 64bit seconds valueJohn Stultz1-4/+3
In order to support dates past 2038 on 32bit systems, ktime_set() needs to handle 64bit second values. [ tglx: Removed the BITS_PER_LONG check ] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org>
2014-07-23ktime: Sanitize ktime_to_us/ms conversionThomas Gleixner1-4/+8
With the plain nanoseconds based ktime_t we can simply use ktime_divns() instead of going through loops and hoops of timespec/timeval conversion. Reported-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org>
2014-07-23ktime: Kill non-scalar ktime_t implementation for 2038John Stultz1-172/+1
The non-scalar ktime_t implementation is basically a timespec which has to be changed to support dates past 2038 on 32bit systems. This patch removes the non-scalar ktime_t implementation, forcing the scalar s64 nanosecond version on all architectures. This may have additional performance overhead on some 32bit systems when converting between ktime_t and timespec structures, however the majority of 32bit systems (arm and i386) were already using scalar ktime_t, so no performance regressions will be seen on those platforms. On affected platforms, I'm open to finding optimizations, including avoiding converting to timespecs where possible. [ tglx: We can now cleanup the ktime_t.tv64 mess, but thats a different issue and we can throw a coccinelle script at it ] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: John Stultz <john.stultz@linaro.org>
2014-06-11ktime: add ktime_after and ktime_before helperDaniel Borkmann1-0/+24
Add two minimal helper functions analogous to time_before() and time_after() that will later on both be needed by SCTP code. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-25ktime: fix some scripts/kernel-doc warningsYacine Belkadi1-13/+15
When building the htmldocs (in verbose mode), scripts/kernel-doc reports the following type of warnings: Warning(include/linux/ktime.h:75): No description found for return value of 'ktime_set' Fix them by using a "Return:" section to describe the return values. (Also apply some minor reformatting along the way.) Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com> Acked-by: Rob Landley <rob@landley.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2013-07-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds1-0/+13
Pull networking updates from David Miller: "This is a re-do of the net-next pull request for the current merge window. The only difference from the one I made the other day is that this has Eliezer's interface renames and the timeout handling changes made based upon your feedback, as well as a few bug fixes that have trickeled in. Highlights: 1) Low latency device polling, eliminating the cost of interrupt handling and context switches. Allows direct polling of a network device from socket operations, such as recvmsg() and poll(). Currently ixgbe, mlx4, and bnx2x support this feature. Full high level description, performance numbers, and design in commit 0a4db187a999 ("Merge branch 'll_poll'") From Eliezer Tamir. 2) With the routing cache removed, ip_check_mc_rcu() gets exercised more than ever before in the case where we have lots of multicast addresses. Use a hash table instead of a simple linked list, from Eric Dumazet. 3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski, Marek Puzyniak, Michal Kazior, and Sujith Manoharan. 4) Support reporting the TUN device persist flag to userspace, from Pavel Emelyanov. 5) Allow controlling network device VF link state using netlink, from Rony Efraim. 6) Support GRE tunneling in openvswitch, from Pravin B Shelar. 7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from Daniel Borkmann and Eric Dumazet. 8) Allow controlling of TCP quickack behavior on a per-route basis, from Cong Wang. 9) Several bug fixes and improvements to vxlan from Stephen Hemminger, Pravin B Shelar, and Mike Rapoport. In particular, support receiving on multiple UDP ports. 10) Major cleanups, particular in the area of debugging and cookie lifetime handline, to the SCTP protocol code. From Daniel Borkmann. 11) Allow packets to cross network namespaces when traversing tunnel devices. From Nicolas Dichtel. 12) Allow monitoring netlink traffic via AF_PACKET sockets, in a manner akin to how we monitor real network traffic via ptype_all. From Daniel Borkmann. 13) Several bug fixes and improvements for the new alx device driver, from Johannes Berg. 14) Fix scalability issues in the netem packet scheduler's time queue, by using an rbtree. From Eric Dumazet. 15) Several bug fixes in TCP loss recovery handling, from Yuchung Cheng. 16) Add support for GSO segmentation of MPLS packets, from Simon Horman. 17) Make network notifiers have a real data type for the opaque pointer that's passed into them. Use this to properly handle network device flag changes in arp_netdev_event(). From Jiri Pirko and Timo Teräs. 18) Convert several drivers over to module_pci_driver(), from Peter Huewe. 19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a O(1) calculation instead. From Eric Dumazet. 20) Support setting of explicit tunnel peer addresses in ipv6, just like ipv4. From Nicolas Dichtel. 21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet. 22) Prevent a single high rate flow from overruning an individual cpu during RX packet processing via selective flow shedding. From Willem de Bruijn. 23) Don't use spinlocks in TCP md5 signing fast paths, from Eric Dumazet. 24) Don't just drop GSO packets which are above the TBF scheduler's burst limit, chop them up so they are in-bounds instead. Also from Eric Dumazet. 25) VLAN offloads are missed when configured on top of a bridge, fix from Vlad Yasevich. 26) Support IPV6 in ping sockets. From Lorenzo Colitti. 27) Receive flow steering targets should be updated at poll() time too, from David Majnemer. 28) Fix several corner case regressions in PMTU/redirect handling due to the routing cache removal, from Timo Teräs. 29) We have to be mindful of ipv4 mapped ipv6 sockets in upd_v6_push_pending_frames(). From Hannes Frederic Sowa. 30) Fix L2TP sequence number handling bugs, from James Chapman." * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits) drivers/net: caif: fix wrong rtnl_is_locked() usage drivers/net: enic: release rtnl_lock on error-path vhost-net: fix use-after-free in vhost_net_flush net: mv643xx_eth: do not use port number as platform device id net: sctp: confirm route during forward progress virtio_net: fix race in RX VQ processing virtio: support unlocked queue poll net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit Documentation: Fix references to defunct linux-net@vger.kernel.org net/fs: change busy poll time accounting net: rename low latency sockets functions to busy poll bridge: fix some kernel warning in multicast timer sfc: Fix memory leak when discarding scattered packets sit: fix tunnel update via netlink dt:net:stmmac: Add dt specific phy reset callback support. dt:net:stmmac: Add support to dwmac version 3.610 and 3.710 dt:net:stmmac: Allocate platform data only if its NULL. net:stmmac: fix memleak in the open method ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available net: ipv6: fix wrong ping_v6_sendmsg return value ...
2013-06-26ktime: add ms_to_ktime() and ktime_add_ms() helpersDaniel Borkmann1-0/+13
Add two ktime helper functions that i) convert a given msec value to a ktime structure and ii) that adds a msec value to a ktime structure. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-29ktime: Add __must_check prefix to ktime_to_timespec_condDaniel Borkmann1-1/+2
The function is currently mainly used in the networking code and if others start using it, they must check the result, otherwise it cannot be determined if the timespec conversion suceeded. Currently no user lacks this check, but make future users aware of a possible misusage. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: John Stultz <john.stultz@linaro.org>
2013-05-29ktime: Use macro NSEC_PER_USEC where appropriateLiu Ying1-3/+4
We've got the macro NSEC_PER_USEC defined in header file include/linux/time.h. To make the code decent, this patch replaces the immediate number 1000 to convert bewteen a time value in microseconds and one in nanoseconds with the macro NSEC_PER_USEC. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Signed-off-by: John Stultz <john.stultz@linaro.org>
2013-04-20net: socket: move ktime2ts to ktime header apiDaniel Borkmann1-0/+18
Currently, ktime2ts is a small helper function that is only used in net/socket.c. Move this helper into the ktime API as a small inline function, so that i) it's maintained together with ktime routines, and ii) also other files can make use of it. The function is named ktime_to_timespec_cond() and placed into the generic part of ktime, since we internally make use of ktime_to_timespec(). ktime_to_timespec() itself does not check the ktime variable for zero, hence, we name this function ktime_to_timespec_cond() for only a conditional conversion, and adapt its users to it. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-11-03pktgen: clean up ktime_t helpersDaniel Borkmann1-0/+19
Some years ago, the ktime_t helper functions ktime_now() and ktime_lt() have been introduced. Instead of defining them inside pktgen.c, they should either use ktime_t library functions or, if not available, they should be defined in ktime.h, so that also others can benefit from them. ktime_compare() is introduced with a similar notion as in timespec_compare(). Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-08-15time: Improve sanity checking of timekeeping inputsJohn Stultz1-7/+0
Unexpected behavior could occur if the time is set to a value large enough to overflow a 64bit ktime_t (which is something larger then the year 2262). Also unexpected behavior could occur if large negative offsets are injected via adjtimex. So this patch improves the sanity check timekeeping inputs by improving the timespec_valid() check, and then makes better use of timespec_valid() to make sure we don't set the time to an invalid negative value or one that overflows ktime_t. Note: This does not protect from setting the time close to overflowing ktime_t and then letting natural accumulation cause the overflow. Reported-by: CAI Qian <caiqian@redhat.com> Reported-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: John Stultz <john.stultz@linaro.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Zhouping Liu <zliu@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1344454580-17031-1-git-send-email-john.stultz@linaro.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2011-03-31Fix common misspellingsLucas De Marchi1-2/+2
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2010-05-14ktime: introduce ktime_to_ms()Chuck Lever1-2/+8
To report ktime statistics to user space in milliseconds, a new helper is required. When considering how to do this conversion, I didn't immediately see why the extra step of converting ktime to a timeval was needed. To make that more clear, introduce a couple of large comments. Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
2008-04-19time: add ns_to_ktime()Ingo Molnar1-0/+6
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-02-15hrtimer: check relative timeouts for overflowThomas Gleixner1-0/+2
Various user space callers ask for relative timeouts. While we fixed that overflow issue in hrtimer_start(), the sites which convert relative user space values to absolute timeouts themself were uncovered. Instead of putting overflow checks into each place add a function which does the sanity checking and convert all affected callers to use it. Thanks to Frans Pop, who reported the problem and tested the fixes. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Tested-by: Frans Pop <elendil@planet.nl>
2008-02-08Fix compilation of powerpc asm-offsets.c with old gccTony Breeds1-1/+2
Commit ad7f71674ad7c3c4467e48f6ab9e85516dae2720 ("[POWERPC] Use a sensible default for clock_getres() in the VDSO") corrected the clock resolution reported by the VDSO clock_getres() but introduced another problem in that older versions of gcc (gcc-4.0 and earlier) fail to compile the new code in arch/powerpc/kernel/asm-offsets.c. This fixes it by introducing a new MONOTONIC_RES_NSEC define in the generic code which is equivalent to KTIME_MONOTONIC_RES but is just an integer constant, not a ktime union. Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-11[KTIME]: Introduce ktime_sub_ns and ktime_sub_usArnaldo Carvalho de Melo1-0/+21
First user will be the DCCP transport networking protocol. Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-07-11[KTIME]: Introduce ktime_add_usArnaldo Carvalho de Melo1-0/+5
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
2007-07-11[KTIME]: Introduce ktime_us_deltaGerrit Renker1-0/+5
This provides a reusable time difference function which returns the difference in microseconds, as often used in the DCCP code. Commiter note: renamed ktime_delta to ktime_us_delta and put it in ktime.h. Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
2007-06-16[TCP]: Congestion control API RTT sampling fixIlpo Järvinen1-0/+12
Commit 164891aadf1721fca4dce473bb0e0998181537c6 broke RTT sampling of congestion control modules. Inaccurate timestamps could be fed to them without providing any way for them to identify such cases. Previously RTT sampler was called only if FLAG_RETRANS_DATA_ACKED was not set filtering inaccurate timestamps nicely. In addition, the new behavior could give an invalid timestamp (zero) to RTT sampler if only skbs with TCPCB_RETRANS were ACKed. This solves both problems. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-09declare struct ktimeAndrew Morton1-2/+4
Some smarty went and inflicted ktime_t as a typedef upon us, so we cannot forward declare it. Create a new `union ktime', map ktime_t onto that. Now we need to kill off this ktime_t thing. Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: john stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-04-26[TCP]: Fix linkage errors on i386.YOSHIFUJI Hideaki1-0/+6
To avoid raw division, use ktime_to_timeval() to get usec. Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2007-03-17[PATCH] fix MTIME_SEC_MAX on 32-bitThomas Gleixner1-1/+5
The maximum seconds value we can handle on 32bit is LONG_MAX. Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-16[PATCH] hrtimers: add high resolution timer supportThomas Gleixner1-2/+1
Implement high resolution timers on top of the hrtimers infrastructure and the clockevents / tick-management framework. This provides accurate timers for all hrtimer subsystem users. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: john stultz <johnstul@us.ibm.com> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-11[PATCH] Numerous fixes to kernel-doc info in source files.Robert P. J. Day1-3/+3
A variety of (mostly) innocuous fixes to the embedded kernel-doc content in source files, including: * make multi-line initial descriptions single line * denote some function names, constants and structs as such * change erroneous opening '/*' to '/**' in a few places * reword some text for clarity Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Cc: "Randy.Dunlap" <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2006-12-07[PATCH] ktime: Fix signed / unsigned mismatch in ktime_to_nsThomas Gleixner1-2/+2
The 32 bit implementation of ktime_to_ns returns unsigned value, while the 64 bit version correctly returns an signed value. There is no current user affected by this, but it has to be fixed, as ktime values can be negative. Pointed-out-by: Helmut Duregger <Helmut.Duregger@student.uibk.ac.at> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-06[PATCH] prevent timespec/timeval to ktime_t overflowThomas Gleixner1-1/+6
Frank v. Waveren pointed out that on 64bit machines the timespec to ktime_t conversion might overflow. This is also true for timeval to ktime_t conversions. This breaks a "sleep inf" on 64bit machines. While a timespec/timeval with tx.sec = MAX_LONG is valid by specification the internal representation of ktime_t is based on nanoseconds. The conversion of seconds to nanoseconds overflows for seconds values >= (MAX_LONG / NSEC_PER_SEC). Check the seconds argument to the conversion and limit it to the maximum time which can be represented by ktime_t. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Frank v Waveren <fvw@var.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-25[PATCH] ktime/hrtimer: fix kernel-doc commentsRandy Dunlap1-8/+0
Fix kernel-doc formatting in ktime.h and hrtimer.[ch] files. Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-26[PATCH] hrtimers: remove DEFINE_KTIME and ktime_to_clock_t()Roman Zippel1-20/+0
Now that it_real_value is gone, the last user of DEFINE_KTIME and ktime_to_clock_t are also gone, so remove it before someone starts using it again. Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-16[PATCH] hrtimer: fix multiple macro argument expansionRoman Zippel1-2/+8
For two macros the arguments were expanded twice, change them to inline functions to avoid it. Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-02-01[PATCH] hrtimers: add back lost credit linesThomas Gleixner1-0/+6
At some point we added credits to people who actively helped to bring k/hr-timers along. This was lost in the big code revamp. Add it back. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-12[hrtimer] Change resolution storage to ktime_t formatThomas Gleixner1-2/+2
Change the storage format of the per base resolution to ktime_t to make it easier accessible in the hrtimers code. Change the resolution from (NSEC_PER_SEC/HZ) to TICK_NSEC as Roman pointed out. TICK_NSEC is closer to the real resolution. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2006-01-10[PATCH] hrtimer: hrtimer core codeThomas Gleixner1-0/+15
hrtimer subsystem core. It is initialized at bootup and expired by the timer interrupt, but is otherwise not utilized by any other subsystem yet. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-10[PATCH] hrtimer: introduce ktime_t time formatThomas Gleixner1-0/+269
- introduce ktime_t: nanosecond-resolution time format. - eliminate the plain s64 scalar type, and always use the union. This simplifies the arithmetics. Idea from Roman Zippel. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>