| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
+little renaming of unicast functions to be smooth with multicast ones
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds ethtool and device feature flag to allow control
of receive hashing offload.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RPS currently depends on SMP and SYSFS
Adding a CONFIG_RPS makes sense in case this requirement changes in the
future. This patch saves about 1500 bytes of kernel text in case SMP is
on but SYSFS is off.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the type change, addresses in unicast and multicast lists wouldn't make
sense, not to mention possible different lenghts. So flush both lists here.
Note "dev_addr_discard" will be very soon replaced by "dev_mc_flush" (once
mc_list conversion will be done).
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
When doing "ifenslave -d bond0 eth0", there is chance to get NULL
dereference in netif_receive_skb(), because dev->master suddenly becomes
NULL after we tested it.
We should use ACCESS_ONCE() to avoid this (or rcu_dereference())
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the possibility to refuse the bonding type change for
other subsystems (such as for example bridge, vlan, etc.)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements software receive side packet steering (RPS). RPS
distributes the load of received packet processing across multiple CPUs.
Problem statement: Protocol processing done in the NAPI context for received
packets is serialized per device queue and becomes a bottleneck under high
packet load. This substantially limits pps that can be achieved on a single
queue NIC and provides no scaling with multiple cores.
This solution queues packets early on in the receive path on the backlog queues
of other CPUs. This allows protocol processing (e.g. IP and TCP) to be
performed on packets in parallel. For each device (or each receive queue in
a multi-queue device) a mask of CPUs is set to indicate the CPUs that can
process packets. A CPU is selected on a per packet basis by hashing contents
of the packet header (e.g. the TCP or UDP 4-tuple) and using the result to index
into the CPU mask. The IPI mechanism is used to raise networking receive
softirqs between CPUs. This effectively emulates in software what a multi-queue
NIC can provide, but is generic requiring no device support.
Many devices now provide a hash over the 4-tuple on a per packet basis
(e.g. the Toeplitz hash). This patch allow drivers to set the HW reported hash
in an skb field, and that value in turn is used to index into the RPS maps.
Using the HW generated hash can avoid cache misses on the packet when
steering it to a remote CPU.
The CPU mask is set on a per device and per queue basis in the sysfs variable
/sys/class/net/<device>/queues/rx-<n>/rps_cpus. This is a set of canonical
bit maps for receive queues in the device (numbered by <n>). If a device
does not support multi-queue, a single variable is used for the device (rx-0).
Generally, we have found this technique increases pps capabilities of a single
queue device with good CPU utilization. Optimal settings for the CPU mask
seem to depend on architectures and cache hierarcy. Below are some results
running 500 instances of netperf TCP_RR test with 1 byte req. and resp.
Results show cumulative transaction rate and system CPU utilization.
e1000e on 8 core Intel
Without RPS: 108K tps at 33% CPU
With RPS: 311K tps at 64% CPU
forcedeth on 16 core AMD
Without RPS: 156K tps at 15% CPU
With RPS: 404K tps at 49% CPU
bnx2x on 16 core AMD
Without RPS 567K tps at 61% CPU (4 HW RX queues)
Without RPS 738K tps at 96% CPU (8 HW RX queues)
With RPS: 854K tps at 76% CPU (4 HW RX queues)
Caveats:
- The benefits of this patch are dependent on architecture and cache hierarchy.
Tuning the masks to get best performance is probably necessary.
- This patch adds overhead in the path for processing a single packet. In
a lightly loaded server this overhead may eliminate the advantages of
increased parallelism, and possibly cause some relative performance degradation.
We have found that masks that are cache aware (share same caches with
the interrupting CPU) mitigate much of this.
- The RPS masks can be changed dynamically, however whenever the mask is changed
this introduces the possibility of generating out of order packets. It's
probably best not change the masks too frequently.
Signed-off-by: Tom Herbert <therbert@google.com>
include/linux/netdevice.h | 32 ++++-
include/linux/skbuff.h | 3 +
net/core/dev.c | 335 +++++++++++++++++++++++++++++++++++++--------
net/core/net-sysfs.c | 225 ++++++++++++++++++++++++++++++-
net/core/skbuff.c | 2 +
5 files changed, 538 insertions(+), 59 deletions(-)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split dev_change_flags() into two functions: __dev_change_flags() to
perform the actual changes and __dev_notify_flags() to invoke netdevice
notifiers. This will be used by rtnl_link to defer netlink notifications
until the device has been fully configured.
This changes ordering of some operations, in particular:
- netlink notifications are sent after all changes have been performed.
As a side effect this surpresses one unnecessary netlink message when
the IFF_UP and other flags are changed simultaneously.
- The NETDEV_UP/NETDEV_DOWN and NETDEV_CHANGE notifiers are invoked
after all changes have been performed. Their relative is unchanged.
- net_dmaengine_put() is invoked before the NETDEV_DOWN notifier instead
of afterwards. This should not make any difference since both RX and TX
are already shut down at this point.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support specifying device flags during device creation,
we must be able to roll back device registration in case setting the
flags fails without sending any notifications related to the device
to userspace.
This patch changes rollback_registered_many() and register_netdevice()
to manually send netlink notifications for devices not handled by
rtnl_link and allows to defer notifications for devices handled by
rtnl_link until setup is complete.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
In "wireless: remove WLAN_80211 and WLAN_PRE80211 from Kconfig" I
inadvertantly missed a line in include/linux/netdevice.h. I thereby
effectively reverted "net: Set LL_MAX_HEADER properly for wireless." by
accident. :-( Now we should check there for CONFIG_WLAN instead.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Cc: stable@kernel.org
|
|
Add netdev ops for configuring SR-IOV VF devices through the PF driver.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add macros to test a private structure for msg_enable bits
and the netif_msg_##bit to test and call netdev_printk if set
Simplifies logic in callers and adds message logging consistency
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These netdev_printk routines take a struct net_device * and emit
dev_printk logging messages adding "%s: " ... netdev->dev.parent
to the dev_printk format and arguments.
This can create some uniformity in the output message log.
These helpers should not be used until a successful alloc_netdev.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patchset enables the ethtool layer to program n-tuple
filters to an underlying device. The idea is to allow capable
hardware to have static rules applied that can assist steering
flows into appropriate queues.
Hardware that is known to support these types of filters today
are ixgbe and niu.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces the similar helpers as those already done for uc list.
However multicast lists are no list_head lists but "mademanually". The three
macros added by this patch will make the transition of mc_list to list_head
smooth in two steps:
1) convert all drivers to use these macros (with the original iterator of type
"struct dev_mc_list")
2) once all drivers are converted, convert list type and iterators to "struct
netdev_hw_addr" in one patch.
>From now on, drivers can (and should) use "netdev_for_each_mc_addr" to iterate
over the addresses with iterator of type "struct netdev_hw_addr". Also macros
"netdev_mc_count" and "netdev_mc_empty" to read list's length. This is the state
which should be reached in all drivers.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the vlan and macvlan drivers, the start_xmit function forwards
data to the dev_queue_xmit function for another device, which may
potentially belong to a different namespace.
To make sure that classification stays within a single namespace,
this resets the potentially critical fields.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces three macros to work with uc list from net drivers.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After netdev_ops compat code HAVE_* macros aren't needed, in fact
they _will_ result in compile breakage for out of tree drivers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Nothing outside of net/core/dev.c uses it.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide common routine for the transition of operational state for a leaf
device during a root device transition.
Signed-off-by: Patrick Mullaney <pmullaney@novell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I will need this shortly to implement network namespace shutdown
batching. For sanity sake network devices should be removed in
the reverse order they were created in.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The veth driver contains code to forward an skb
from the start_xmit function of one network
device into the receive path of another device.
Moving that code into a common location lets us
reuse the code for direct forwarding of data
between macvlan ports, and possibly in other
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Herbert Xu a écrit :
> On Tue, Nov 17, 2009 at 04:26:04AM -0800, David Miller wrote:
>> Really, the link watch stuff is just due for a redesign. I don't
>> think a simple hack is going to cut it this time, sorry Eric :-)
>
> I have no objections against any redesigns, but since the only
> caller of linkwatch_forget_dev runs in process context with the
> RTNL, it could also legally emit those events.
Thanks guys, here an updated version then, before linkwatch surgery ?
In this version, I force the event to be sent synchronously.
[PATCH net-next-2.6] linkwatch: linkwatch_forget_dev() to speedup device dismantle
time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105
real 0m0.266s
user 0m0.000s
sys 0m0.001s
real 0m0.770s
user 0m0.000s
sys 0m0.000s
real 0m1.022s
user 0m0.000s
sys 0m0.000s
One problem of current schem in vlan dismantle phase is the
holding of device done by following chain :
vlan_dev_stop() ->
netif_carrier_off(dev) ->
linkwatch_fire_event(dev) ->
dev_hold() ...
And __linkwatch_run_queue() runs up to one second later...
A generic fix to this problem is to add a linkwatch_forget_dev() method
to unlink the device from the list of watched devices.
dev->link_watch_next becomes dev->link_watch_list (and use a bit more memory),
to be able to unlink device in O(1).
After patch :
time ip link del eth3.103 ; time ip link del eth3.104 ; time ip link del eth3.105
real 0m0.024s
user 0m0.000s
sys 0m0.000s
real 0m0.032s
user 0m0.000s
sys 0m0.001s
real 0m0.033s
user 0m0.000s
sys 0m0.000s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers ndo_get_stats() method need to perform txqueue stats folding.
Move folding from dev_get_stats() to a new dev_txq_stats_fold() function
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent changes in the TX error propagation require additional checking
and masking of values returned from hard_start_xmit(), mainly to
separate cases where skb was consumed. This aim can be simplified by
changing the order of NETDEV_TX and NET_XMIT codes, because the latter
are treated similarly to negative (ERRNO) values.
After this change much simpler dev_xmit_complete() is also used in
sch_direct_xmit(), so it is moved to netdevice.h.
Additionally NET_RX definitions in netdevice.h are moved up from
between TX codes to avoid confusion while reading the TX comment.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer need read_lock(&dev_base_lock), use RCU instead.
We also can avoid taking references on inet6_dev structs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the ->ndo_hard_start_xmit() callbacks are only permitted to return
one of the NETDEV_TX codes. This prevents any kind of error propagation for
virtual devices, like queue congestion of the underlying device in case of
layered devices, or unreachability in case of tunnels.
This patches changes the NET_XMIT codes to avoid clashes with the NETDEV_TX
codes and changes the two callers of dev_hard_start_xmit() to expect either
errno codes, NET_XMIT codes or NETDEV_TX codes as return value.
In case of qdisc_restart(), all non NETDEV_TX codes are mapped to NETDEV_TX_OK
since no error propagation is possible when using qdiscs. In case of
dev_queue_xmit(), the error is propagated upwards.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds an RCU macro for continuing search, useful for some
network devices like vlan.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This cleanup patch puts struct/union/enum opening braces,
in first line to ease grep games.
struct something
{
becomes :
struct something {
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds RCU management to the list of netdevices.
Convert some for_each_netdev() users to RCU version, if
it can avoid read_lock-ing dev_base_lock
Ie:
read_lock(&dev_base_loack);
for_each_netdev(net, dev)
some_action();
read_unlock(&dev_base_lock);
becomes :
rcu_read_lock();
for_each_netdev_rcu(net, dev)
some_action();
rcu_read_unlock();
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock
(and avoid touching netdevice refcount)
netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.
However, it adds a synchronize_rcu() call in dev_change_name()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This isn't beautifully abstracted, but it is simple,
simplifies uses and so far is only needed for the bonding driver.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will allow drivers to adjust their receive path dynamically
based on whether GRO is being applied successfully.
Currently all in-tree callers ignore the return values of these
functions and do not need to be changed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This clarifies which return and parameter types are GRO result codes
and not RX result codes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock.
netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.
dev_ifname() converted to dev_get_by_index_rcu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ndo_fcoe_get_wwn so Fiber Channel over Ethernet (FCoE) can make use of
the provided World Wide Port Name (WWPN) and World Wide Node Name (WWNN)
from the underlying network interface driver.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce rollback_registered_many() and unregister_netdevice_many()
rollback_registered_many() is able to perform necessary steps at device dismantle
time, factorizing two expensive synchronize_net() calls.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patchs adds an unreg_list anchor to struct net_device, and
introduces an unregister_netdevice_queue() function, able to queue
a net_device to a list instead of immediately unregister it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
nanodoc was missing an ndo_-prefix.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The data center bridging ops structure can be const
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
be2net: fix some cmds to use mccq instead of mbox
atl1e: fix 2.6.31-git4 -- ATL1E 0000:03:00.0: DMA-API: device driver frees DMA
pkt_sched: Fix qstats.qlen updating in dump_stats
ipv6: Log the affected address when DAD failure occurs
wl12xx: Fix print_mac() conversion.
af_iucv: fix race when queueing skbs on the backlog queue
af_iucv: do not call iucv_sock_kill() twice
af_iucv: handle non-accepted sockets after resuming from suspend
af_iucv: fix race in __iucv_sock_wait()
iucv: use correct output register in iucv_query_maxconn()
iucv: fix iucv_buffer_cpumask check when calling IUCV functions
iucv: suspend/resume error msg for left over pathes
wl12xx: switch to %pM to print the mac address
b44: the poll handler b44_poll must not enable IRQ unconditionally
ipv6: Ignore route option with ROUTER_PREF_INVALID
bonding: make ab_arp select active slaves as other modes
cfg80211: fix SME connect
rc80211_minstrel: fix contention window calculation
ssb/sdio: fix printk format warnings
p54usb: add Zcomax XG-705A usbid
...
|
|
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch fixes commit e36b9d16c6a6d0f59803b3ef04ff3c22c3844c10. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:
*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.
The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the multiqueue integration with the qdisc API suffers from
a few problems:
- with multiple queues, all root qdiscs use the same handle. This means
they can't be exposed to userspace in a backwards compatible fashion.
- all API operations always refer to queue number 0. Newly created
qdiscs are automatically shared between all queues, its not possible
to address individual queues or restore multiqueue behaviour once a
shared qdisc has been attached.
- Dumps only contain the root qdisc of queue 0, in case of non-shared
qdiscs this means the statistics are incomplete.
This patch reintroduces dev->qdisc, which points to the (single) root qdisc
from userspace's point of view. Currently it either points to the first
(non-shared) default qdisc, or a qdisc shared between all queues. The
following patches will introduce a classful dummy qdisc, which will be used
as root qdisc and contain the per-queue qdiscs as children.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
