| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This aligns broadcast sync_timeout with existing connection timeouts
which are 20 seconds long.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The ATS2851 controller erroneously reports support for the "Read
Encryption Key Length" HCI command. This makes it unable to connect
to any devices, since this command is issued by the kernel during the
connection process in response to an "Encryption Change" HCI event.
Add a new quirk (HCI_QUIRK_BROKEN_ENC_KEY_SIZE) to hint that the command
is unsupported, preventing it from interrupting the connection process.
This is the error log from btmon before this patch:
> HCI Event: Encryption Change (0x08) plen 4
Status: Success (0x00)
Handle: 2048 Address: ...
Encryption: Enabled with E0 (0x01)
< HCI Command: Read Encryption Key Size (0x05|0x0008) plen 2
Handle: 2048 Address: ...
> HCI Event: Command Status (0x0f) plen 4
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Vinicius Peixoto <nukelet64@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In a few cases the stack may generate commands as responses to events
which would happen to overwrite the sent_cmd, so this attempts to store
the request in req_skb so even if sent_cmd is replaced with a new
command the pending request will remain in stored in req_skb.
Fixes: 6a98e3836fa2 ("Bluetooth: Add helper for serialized HCI command execution")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support to reassemble PA data for a Broadcast Sink
listening socket. This is needed in case the BASE is received
fragmented in multiple PA reports.
PA data is first reassembled inside the hcon, before the BASE
is extracted and stored inside the socket. The length of the
le_per_adv_data hcon array has been raised to 1650, to accommodate
the maximum PA data length that can come fragmented, according to
spec.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This creates a hcon instance at bis listen, before the PA sync
procedure is started.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If connection is still queued/pending in the cmd_sync queue it means no
command has been generated and it should be safe to just dequeue the
callback when it is being aborted.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds functions to queue, dequeue and lookup into the cmd_sync
list.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the UAF on __hci_acl_create_connection_sync caused by
connection abortion, it uses the same logic as to LE_LINK which uses
hci_cmd_sync_cancel to prevent the callback to run if the connection is
abort prematurely.
Reported-by: syzbot+3f0a39be7a2035700868@syzkaller.appspotmail.com
Fixes: 45340097ce6e ("Bluetooth: hci_conn: Only do ACL connections sequentially")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This aligns the use socket sk_timeo as conn_timeout when initiating a
connection and then use it when scheduling the resulting HCI command,
that way the command is actually aborted synchronously thus not
blocking commands generated by hci_abort_conn_sync to inform the
controller the connection is to be aborted.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
With the last commit we moved to using the hci_sync queue for "Create
Connection" requests, removing the need for retrying the paging after
finished/failed "Create Connection" requests and after the end of
inquiries.
hci_conn_check_pending() was used to trigger this retry, we can remove it
now.
Note that we can also remove the special handling for COMMAND_DISALLOWED
errors in the completion handler of "Create Connection", because "Create
Connection" requests are now always serialized.
This is somewhat reverting commit 4c67bc74f016 ("[Bluetooth] Support
concurrent connect requests").
With this, the BT_CONNECT2 state of ACL hci_conn objects should now be
back to meaning only one thing: That we received a "Connection Request"
from another device (see hci_conn_request_evt), but the response to that
is going to be deferred.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Pretty much all bluetooth chipsets only support paging a single device at
a time, and if they don't reject a secondary "Create Connection" request
while another is still ongoing, they'll most likely serialize those
requests in the firware.
With commit 4c67bc74f016 ("[Bluetooth] Support concurrent connect
requests") we started adding some serialization of our own in case the
adapter returns "Command Disallowed" HCI error.
This commit was using the BT_CONNECT2 state for the serialization, this
state is also used for a few more things (most notably to indicate we're
waiting for an inquiry to cancel) and therefore a bit unreliable. Also
not all BT firwares would respond with "Command Disallowed" on too many
connection requests, some will also respond with "Hardware Failure"
(BCM4378), and others will error out later and send a "Connect Complete"
event with error "Rejected Limited Resources" (Marvell 88W8897).
We can clean things up a bit and also make the serialization more reliable
by using our hci_sync machinery to always do "Create Connection" requests
in a sequential manner.
This is very similar to what we're already doing for establishing LE
connections, and it works well there.
Note that this causes a test failure in mgmt-tester (test "Pair Device
- Power off 1") because the hci_abort_conn_sync() changes the error we
return on timeout of the "Create Connection". We'll fix this on the
mgmt-tester side by adjusting the expected error for the test.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
High Speed, Alternate MAC and PHY (AMP) extension, has been removed from
Bluetooth Core specification on 5.3:
https://www.bluetooth.com/blog/new-core-specification-v5-3-feature-enhancements/
Fixes: 244bc377591c ("Bluetooth: Add BT_HS config option")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If command has timed out call __hci_cmd_sync_cancel to notify the
hci_req since it will inevitably cause a timeout.
This also rework the code around __hci_cmd_sync_cancel since it was
wrongly assuming it needs to cancel timer as well, but sometimes the
timers have not been started or in fact they already had timed out in
which case they don't need to be cancel yet again.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
We have error defines already, so let's use them.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add a new state HCI_POWERING_DOWN that indicates that the device is
currently powering down, this will be useful for the next commit.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
With commit cf75ad8b41d2 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED"),
the power off sequence got refactored so that this timeout was no longer
necessary, let's remove the leftover define from the header too.
Fixes: cf75ad8b41d2 ("Bluetooth: hci_sync: Convert MGMT_SET_POWERED")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This reverts 19f8def031bfa50c579149b200bfeeb919727b27
"Bluetooth: Fix auth_complete_evt for legacy units" which seems to be
working around a bug on a broken controller rather then any limitation
imposed by the Bluetooth spec, in fact if there ws not possible to
re-auth the command shall fail not succeed.
Fixes: 19f8def031bf ("Bluetooth: Fix auth_complete_evt for legacy units")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This removes le_restart_scan work and instead just disables controller
duplicate filtering when discovery result_filtering is enabled and
HCI_QUIRK_STRICT_DUPLICATE_FILTER is set.
Link: https://github.com/bluez/bluez/issues/573
Link: https://github.com/bluez/bluez/issues/572
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
For ISO Broadcast, all BISes from a BIG have the same lifespan - they
cannot be created or terminated independently from each other.
This links together all BIS hcons that are part of the same BIG, so all
hcons are kept alive as long as the BIG is active.
If multiple BIS sockets are opened for a BIG handle, and only part of
them are closed at some point, the associated hcons will be marked as
open. If new sockets will later be opened for the same BIG, they will
be reassociated with the open BIS hcons.
All BIS hcons will be cleaned up and the BIG will be terminated when
the last BIS socket is closed from userspace.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If two Bluetooth devices both support BR/EDR and BLE, and also
support Secure Connections, then they only need to pair once.
The LTK generated during the LE pairing process may be converted
into a BR/EDR link key for BR/EDR transport, and conversely, a
link key generated during the BR/EDR SSP pairing process can be
converted into an LTK for LE transport. Hence, the link type of
the link key and LTK is not fixed, they can be either an LE LINK
or an ACL LINK.
Currently, in the mgmt_new_irk/ltk/crsk/link_key functions, the
link type is fixed, which could lead to incorrect address types
being reported to the application layer. Therefore, it is necessary
to add link_type/addr_type to the smp_irk/ltk/crsk and link_key,
to ensure the generation of the correct address type.
SMP over BREDR:
Before Fix:
> ACL Data RX: Handle 11 flags 0x02 dlen 12
BR/EDR SMP: Identity Address Information (0x09) len 7
Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
Random address: 00:00:00:00:00:00 (Non-Resolvable)
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated key from P-256 (0x03)
After Fix:
> ACL Data RX: Handle 11 flags 0x02 dlen 12
BR/EDR SMP: Identity Address Information (0x09) len 7
Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
Random address: 00:00:00:00:00:00 (Non-Resolvable)
BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated key from P-256 (0x03)
SMP over LE:
Before Fix:
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
Random address: 5F:5C:07:37:47:D5 (Resolvable)
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated key from P-256 (0x03)
@ MGMT Event: New Link Key (0x0009) plen 26
BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated Combination key from P-256 (0x08)
After Fix:
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
Random address: 5E:03:1C:00:38:21 (Resolvable)
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated key from P-256 (0x03)
@ MGMT Event: New Link Key (0x0009) plen 26
Store hint: Yes (0x01)
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated Combination key from P-256 (0x08)
Cc: stable@vger.kernel.org
Signed-off-by: Xiao Yao <xiaoyao@rock-chips.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_conn_hash_lookup_cis shall always match the requested CIG and CIS
ids even when they are unset as otherwise it result in not being able
to bind/connect different sockets to the same address as that would
result in having multiple sockets mapping to the same hci_conn which
doesn't really work and prevents BAP audio configuration such as
AC 6(i) when CIG and CIS are left unset.
Fixes: c14516faede3 ("Bluetooth: hci_conn: Fix not matching by CIS ID")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The handle of new hci_conn is always HCI_CONN_HANDLE_MAX + 1 if
the handle of the first hci_conn entry in hci_dev->conn_hash->list
is not HCI_CONN_HANDLE_MAX + 1. Use ida to manage the allocation of
hci_conn->handle to make it be unique.
Fixes: 9f78191cc9f1 ("Bluetooth: hci_conn: Always allocate unique handles")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the cleanup callback for slave bis and pa sync hcons.
Closing all bis hcons will trigger BIG Terminate Sync, while closing
all bises and the pa sync hcon will also trigger PA Terminate Sync.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This enables a broadcast sink to be informed if the PA
it has synced with is associated with an encrypted BIG,
by retrieving the socket QoS and checking the encryption
field.
After PA sync has been successfully established and the
first BIGInfo advertising report is received, a new hcon
is added and notified to the ISO layer. The ISO layer
sets the encryption field of the socket and hcon QoS
according to the encryption parameter of the BIGInfo
advertising report event.
After that, the userspace is woken up, and the QoS of the
new PA sync socket can be read, to inspect the encryption
field and follow up accordingly.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the master BIS cleanup procedure - as opposed to CIS cleanup,
no HCI disconnect command should be issued. A master BIS should only be
terminated by disabling periodic and extended advertising, and terminating
the BIG.
In case of a Broadcast Receiver, all BIS and PA connections can be
cleaned up by calling hci_conn_failed, since it contains all function
calls that are necessary for successful cleanup.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Cross-merge networking fixes after downstream PR.
net/mac80211/key.c
02e0e426a2fb ("wifi: mac80211: fix error path key leak")
2a8b665e6bcc ("wifi: mac80211: remove key_mtx")
7d6904bf26b9 ("Merge wireless into wireless-next")
https://lore.kernel.org/all/20231012113648.46eea5ec@canb.auug.org.au/
Adjacent changes:
drivers/net/ethernet/ti/Kconfig
a602ee3176a8 ("net: ethernet: ti: Fix mixed module-builtin object")
98bdeae9502b ("net: cpmac: remove driver to prepare for platform removal")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The code pattern of memcpy(dst, src, strlen(src)) is almost always
wrong. In this case it is wrong because it leaves memory uninitialized
if it is less than sizeof(ni->name), and overflows ni->name when longer.
Normally strtomem_pad() could be used here, but since ni->name is a
trailing array in struct hci_mon_new_index, compilers that don't support
-fstrict-flex-arrays=3 can't tell how large this array is via
__builtin_object_size(). Instead, open-code the helper and use sizeof()
since it will work correctly.
Additionally mark ni->name as __nonstring since it appears to not be a
%NUL terminated C string.
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Edward AD <twuufnxlz@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netdev@vger.kernel.org
Fixes: 18f547f3fc07 ("Bluetooth: hci_sock: fix slab oob read in create_monitor_event")
Link: https://lore.kernel.org/lkml/202310110908.F2639D3276@keescook/
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts (or adjacent changes of note).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a followup of 8bf43be799d4 ("net: annotate data-races
around sk->sk_priority").
sk->sk_priority can be read and written without holding the socket lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the following warnings:
net/bluetooth/hci_core.c: In function ‘hci_register_dev’:
net/bluetooth/hci_core.c:2620:54: warning: ‘%d’ directive output may
be truncated writing between 1 and 10 bytes into a region of size 5
[-Wformat-truncation=]
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~
net/bluetooth/hci_core.c:2620:50: note: directive argument in the range
[0, 2147483647]
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~~~~~~
net/bluetooth/hci_core.c:2620:9: note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 8
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This introduces HCI_QUIRK_BROKEN_LE_CODED which is used to indicate
that LE Coded PHY shall not be used, it is then set for some Intel
models that claim to support it but when used causes many problems.
Cc: stable@vger.kernel.org # 6.4.y+
Link: https://github.com/bluez/bluez/issues/577
Link: https://github.com/bluez/bluez/issues/582
Link: https://lore.kernel.org/linux-bluetooth/CABBYNZKco-v7wkjHHexxQbgwwSz-S=GZ=dZKbRE1qxT1h4fFbQ@mail.gmail.com/T/#
Fixes: 288c90224eec ("Bluetooth: Enable all supported LE PHY by default")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In the case of a Periodic Synchronized Receiver,
the PA report received from a Broadcaster contains the BASE,
which has information about codec and other parameters of a BIG.
This isnformation is stored and the application can retrieve it
using getsockopt(BT_ISO_BASE).
Signed-off-by: Claudia Draghicescu <claudia.rosu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
There a few instances still using HCI_MAX_AD_LENGTH instead of using
max_adv_len which takes care of detecting what is the actual maximum
length depending on if the controller supports EA or not.
Fixes: 112b5090c219 ("Bluetooth: MGMT: Fix always using HCI_MAX_AD_LENGTH")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This commit implements defer setup support for the Broadcast Sink
scenario: By setting defer setup on a broadcast socket before calling
listen, the user is able to trigger the PA sync and BIG sync procedures
separately.
This is useful if the user first wants to synchronize to the periodic
advertising transmitted by a Broadcast Source, and trigger the BIG sync
procedure later on.
If defer setup is set, once a PA sync established event arrives, a new
hcon is created and notified to the ISO layer. A child socket associated
with the PA sync connection will be added to the accept queue of the
listening socket.
Once the accept call returns the fd for the PA sync child socket, the
user should call read on that fd. This will trigger the BIG create sync
procedure, and the PA sync socket will become a listening socket itself.
When the BIG sync established event is notified to the ISO layer, the
bis connections will be added to the accept queue of the PA sync parent.
The user should call accept on the PA sync socket to get the final bis
connections.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The CIS/CIG ids of ISO connections are defined only when the connection
is unicast.
Fix the lookup functions to check for unicast first. Ensure CIG/CIS
IDs have valid value also in state BT_OPEN.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This introduces PTR_UINT/UINT_PTR macros and replace the use of
PTR_ERR/ERR_PTR.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This moves hci_is_le_conn_scanning to hci_core.h so it can be used by
different files without having to duplicate its code.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This introduces hci_conn_set_handle which takes care of verifying the
conditions where the hci_conn handle can be modified, including when
hci_conn_abort has been called and also checks that the handles is
valid as well.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This makes the handling of BT_PKT_STATUS more generic so it can be
reused by sockets other than SCO like BT_DEFER_SETUP, etc.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
HCI_MAX_AD_LENGTH shall only be used if the controller doesn't support
extended advertising, otherwise HCI_MAX_EXT_AD_LENGTH shall be used
instead.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Some use cases require the user to be informed if BIG synchronization
fails. This commit makes it so that even if the BIG sync established
event arrives with error status, a new hconn is added for each BIS,
and the iso layer is notified about the failed connections.
Unsuccesful bis connections will be marked using the
HCI_CONN_BIG_SYNC_FAILED flag. From the iso layer, the POLLERR event
is triggered on the newly allocated bis sockets, before adding them
to the accept list of the parent socket.
From user space, a new fd for each failed bis connection will be
obtained by calling accept. The user should check for the POLLERR
event on the new socket, to determine if the connection was successful
or not.
The HCI_CONN_BIG_SYNC flag has been added to mark whether the BIG sync
has been successfully established. This flag is checked at bis cleanup,
so the HCI LE BIG Terminate Sync command is only issued if needed.
The BT_SK_BIG_SYNC flag indicates if BIG create sync has been called
for a listening socket, to avoid issuing the command everytime a BIGInfo
advertising report is received.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This attempts to always allocate a unique handle for connections so they
can be properly aborted by the likes of hci_abort_conn, so this uses the
invalid range as a pool of unset handles that way if userspace is trying
to create multiple connections at once each will be given a unique
handle which will be considered unset.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This consolidates code for aborting connections using
hci_cmd_sync_queue so it is synchronized with other threads, but
because of the fact that some commands may block the cmd_sync_queue
while waiting specific events this attempt to cancel those requests by
using hci_cmd_sync_cancel.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Since limited tracking device per condition, this feature is to support
tracking multiple devices concurrently.
When a pattern monitor detects the device, this feature issues an address
monitor for tracking that device. Let pattern monitor can keep monitor
new devices.
This feature adds an address filter when receiving a LE monitor device
event which monitor handle is for a pattern, and the controller started
monitoring the device. And this feature also has cancelled the monitor
advertisement from address filters when receiving a LE monitor device
event when the controller stopped monitoring the device specified by an
address and monitor handle.
Below is an example to know the feature adds the address filter.
//Add MSFT pattern monitor
< HCI Command: Vendor (0x3f|0x00f0) plen 14 #142 [hci0] 55.552420
03 b8 a4 03 ff 01 01 06 09 05 5f 52 45 46 .........._REF
> HCI Event: Command Complete (0x0e) plen 6 #143 [hci0] 55.653960
Vendor (0x3f|0x00f0) ncmd 2
Status: Success (0x00)
03 00
//Got event from the pattern monitor
> HCI Event: Vendor (0xff) plen 18 #148 [hci0] 58.384953
23 79 54 33 77 88 97 68 02 00 fb c1 29 eb 27 b8 #yT3w..h....).'.
00 01 ..
//Add MSFT address monitor (Sample address: B8:27:EB:29:C1:FB)
< HCI Command: Vendor (0x3f|0x00f0) plen 13 #149 [hci0] 58.385067
03 b8 a4 03 ff 04 00 fb c1 29 eb 27 b8 .........).'.
//Report to userspace about found device (ADV Monitor Device Found)
@ MGMT Event: Unknown (0x002f) plen 38 {0x0003} [hci0] 58.680042
01 00 fb c1 29 eb 27 b8 01 ce 00 00 00 00 16 00 ....).'.........
0a 09 4b 45 59 42 44 5f 52 45 46 02 01 06 03 19 ..KEYBD_REF.....
c1 03 03 03 12 18 ......
//Got event from address monitor
> HCI Event: Vendor (0xff) plen 18 #152 [hci0] 58.672956
23 79 54 33 77 88 97 68 02 00 fb c1 29 eb 27 b8 #yT3w..h....).'.
01 01
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support for creating multiple BIGs. According to
spec, each BIG shall have an unique handle, and each BIG should
be associated with a different advertising handle. Otherwise,
the LE Create BIG command will fail, with error code
Command Disallowed (for reusing a BIG handle), or
Unknown Advertising Identifier (for reusing an advertising
handle).
The btmon snippet below shows an exercise for creating two BIGs
for the same controller, by opening two isotest instances with
the following command:
tools/isotest -i hci0 -s 00:00:00:00:00:00
< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31
Handle: 0x00
Advertising Handle: 0x01
Number of BIS: 1
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 21
LE Broadcast Isochronous Group Complete (0x1b)
Status: Success (0x00)
Handle: 0x00
BIG Synchronization Delay: 912 us (0x000390)
Transport Latency: 912 us (0x000390)
PHY: LE 2M (0x02)
NSE: 3
BN: 1
PTO: 1
IRC: 3
Maximum PDU: 40
ISO Interval: 10.00 msec (0x0008)
Connection Handle #0: 10
< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068)
Handle: 0x01
Advertising Handle: 0x02
Number of BIS: 1
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This stores scm_creds into hci_skb_cb so they can be properly forwarded
to the likes of btmon which is then able to print information about the
process who is originating the traffic:
bluetoothd[35]: @ MGMT Command: Rea.. (0x0001) plen 0 {0x0001}
@ MGMT Event: Command Complete (0x0001) plen 6 {0x0001}
Read Management Version Information (0x0001) plen 3
bluetoothd[35]: < ACL Data T.. flags 0x00 dlen 41
ATT: Write Command (0x52) len 36
Handle: 0x0043 Type: ASE Control Point (0x2bc6)
Data: 020203000110270000022800020a00409c0001000110270000022800020a00409c00
Opcode: QoS Configuration (0x02)
Number of ASE(s): 2
ASE: #0
ASE ID: 0x03
CIG ID: 0x00
CIS ID: 0x01
SDU Interval: 10000 usec
Framing: Unframed (0x00)
PHY: 0x02
LE 2M PHY (0x02)
Max SDU: 40
RTN: 2
Max Transport Latency: 10
Presentation Delay: 40000 us
ASE: #1
ASE ID: 0x01
CIG ID: 0x00
CIS ID: 0x01
SDU Interval: 10000 usec
Framing: Unframed (0x00)
PHY: 0x02
LE 2M PHY (0x02)
Max SDU: 40
RTN: 2
Max Transport Latency: 10
Presentation Delay: 40000 us
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This consolidates code around sk_alloc into bt_sock_alloc which does
take care of common initialization.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
LE Create CIS command shall not be sent before all CIS Established
events from its previous invocation have been processed. Currently it is
sent via hci_sync but that only waits for the first event, but there can
be multiple.
Make it wait for all events, and simplify the CIS creation as follows:
Add new flag HCI_CONN_CREATE_CIS, which is set if Create CIS has been
sent for the connection but it is not yet completed.
Make BT_CONNECT state to mean the connection wants Create CIS.
On events after which new Create CIS may need to be sent, send it if
possible and some connections need it. These events are:
hci_connect_cis, iso_connect_cfm, hci_cs_le_create_cis,
hci_le_cis_estabilished_evt.
The Create CIS status/completion events shall queue new Create CIS only
if at least one of the connections transitions away from BT_CONNECT, so
that we don't loop if controller is sending bogus events.
This fixes sending multiple CIS Create for the same CIS in the
"ISO AC 6(i) - Success" BlueZ test case:
< HCI Command: LE Create Co.. (0x08|0x0064) plen 9 #129 [hci0]
Number of CIS: 2
CIS Handle: 257
ACL Handle: 42
CIS Handle: 258
ACL Handle: 42
> HCI Event: Command Status (0x0f) plen 4 #130 [hci0]
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29 #131 [hci0]
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 257
...
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13 #132 [hci0]
...
> HCI Event: Command Complete (0x0e) plen 6 #133 [hci0]
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
...
< HCI Command: LE Create Co.. (0x08|0x0064) plen 5 #134 [hci0]
Number of CIS: 1
CIS Handle: 258
ACL Handle: 42
> HCI Event: Command Status (0x0f) plen 4 #135 [hci0]
LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
Status: ACL Connection Already Exists (0x0b)
> HCI Event: LE Meta Event (0x3e) plen 29 #136 [hci0]
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 258
...
Fixes: c09b80be6ffc ("Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
It is required for some configurations to have multiple BISes as part
of the same BIG.
Similar to the flow implemented for unicast, DEFER_SETUP will also be
used to bind multiple BISes for the same BIG, before starting Periodic
Advertising and creating the BIG.
The user will have to open a new socket for each BIS. By setting the
BT_DEFER_SETUP socket option and calling connect, a new connection
will be added for the BIG and advertising handle set by the socket
QoS parameters. Since all BISes will be bound for the same BIG and
advertising handle, the socket QoS options and base parameters should
match for all connections.
By calling connect on a socket that does not have the BT_DEFER_SETUP
option set, periodic advertising will be started and the BIG will
be created, with a BIS for each previously bound connection. Since
a BIG cannot be reconfigured with additional BISes after creation,
no more connections can be bound for the BIG after the start periodic
advertising and create BIG commands have been queued.
The bis_cleanup function has also been updated, so that the advertising
set and the BIG will not be terminated unless there are no more
bound or connected BISes.
The HCI_CONN_BIG_CREATED connection flag has been added to indicate
that the BIG has been successfully created. This flag is checked at
bis_cleanup, so that the BIG is only terminated if the
HCI_LE_Create_BIG_Complete has been received.
This implementation has been tested on hardware, using the "isotest"
tool with an additional command line option, to specify the number of
BISes to create as part of the desired BIG:
tools/isotest -i hci0 -s 00:00:00:00:00:00 -N 2 -G 1 -T 1
The btmon log shows that a BIG containing 2 BISes has been created:
< HCI Command: LE Create Broadcast Isochronous Group (0x08|0x0068) plen 31
Handle: 0x01
Advertising Handle: 0x01
Number of BIS: 2
SDU Interval: 10000 us (0x002710)
Maximum SDU size: 40
Maximum Latency: 10 ms (0x000a)
RTN: 0x02
PHY: LE 2M (0x02)
Packing: Sequential (0x00)
Framing: Unframed (0x00)
Encryption: 0x00
Broadcast Code: 00000000000000000000000000000000
> HCI Event: Command Status (0x0f) plen 4
LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 23
LE Broadcast Isochronous Group Complete (0x1b)
Status: Success (0x00)
Handle: 0x01
BIG Synchronization Delay: 1974 us (0x0007b6)
Transport Latency: 1974 us (0x0007b6)
PHY: LE 2M (0x02)
NSE: 3
BN: 1
PTO: 1
IRC: 3
Maximum PDU: 40
ISO Interval: 10.00 msec (0x0008)
Connection Handle #0: 10
Connection Handle #1: 11
< HCI Command: LE Setup Isochronous Data Path (0x08|0x006e) plen 13
Handle: 10
Data Path Direction: Input (Host to Controller) (0x00)
Data Path: HCI (0x00)
Coding Format: Transparent (0x03)
Company Codec ID: Ericsson Technology Licensing (0)
Vendor Codec ID: 0
Controller Delay: 0 us (0x000000)
Codec Configuration Length: 0
Codec Configuration:
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 10
< HCI Command: LE Setup Isochronous Data Path (0x08|0x006e) plen 13
Handle: 11
Data Path Direction: Input (Host to Controller) (0x00)
Data Path: HCI (0x00)
Coding Format: Transparent (0x03)
Company Codec ID: Ericsson Technology Licensing (0)
Vendor Codec ID: 0
Controller Delay: 0 us (0x000000)
Codec Configuration Length: 0
Codec Configuration:
> HCI Event: Command Complete (0x0e) plen 6
LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
Status: Success (0x00)
Handle: 11
< ISO Data TX: Handle 10 flags 0x02 dlen 44
< ISO Data TX: Handle 11 flags 0x02 dlen 44
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 10
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 11
Count: 1
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch checks for ISO_BROADCASTER and ISO_SYNC_RECEIVER in
controller.
Signed-off-by: Claudia Draghicescu <claudia.rosu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
