summaryrefslogtreecommitdiff
path: root/net/sctp/output.c
AgeCommit message (Collapse)AuthorFilesLines
2022-05-16net: allow gso_max_size to exceed 65536Alexander Duyck1-1/+2
The code for gso_max_size was added originally to allow for debugging and workaround of buggy devices that couldn't support TSO with blocks 64K in size. The original reason for limiting it to 64K was because that was the existing limits of IPv4 and non-jumbogram IPv6 length fields. With the addition of Big TCP we can remove this limit and allow the value to potentially go up to UINT_MAX and instead be limited by the tso_max_size value. So in order to support this we need to go through and clean up the remaining users of the gso_max_size value so that the values will cap at 64K for non-TCPv6 flows. In addition we can clean up the GSO_MAX_SIZE value so that 64K becomes GSO_LEGACY_MAX_SIZE and UINT_MAX will now be the upper limit for GSO_MAX_SIZE. v6: (edumazet) fixed a compile error if CONFIG_IPV6=n, in a new sk_trim_gso_size() helper. netif_set_tso_max_size() caps the requested TSO size with GSO_MAX_SIZE. Signed-off-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22net: annotate accesses to dev->gso_max_sizeEric Dumazet1-1/+1
dev->gso_max_size is written under RTNL protection, or when the device is not yet visible, but is read locklessly. Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_size() where we can to better document what is going on. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-29sctp: allow IP fragmentation when PLPMTUD enters Error stateXin Long1-5/+8
Currently when PLPMTUD enters Error state, transport pathmtu will be set to MIN_PLPMTU(512) while probe is continuing with BASE_PLPMTU(1200). It will cause pathmtu to stay in a very small value, even if the real pmtu is some value like 1000. RFC8899 doesn't clearly say how to set the value in Error state. But one possibility could be keep using BASE_PLPMTU for the real pmtu, but allow to do IP fragmentation when it's in Error state. As it says in rfc8899#section-5.4: Some paths could be unable to sustain packets of the BASE_PLPMTU size. The Error State could be implemented to provide robustness to such paths. This allows fallback to a smaller than desired PLPMTU rather than suffer connectivity failure. This could utilize methods such as endpoint IP fragmentation to enable the PL sender to communicate using packets smaller than the BASE_PLPMTU. This patch is to set pmtu to BASE_PLPMTU instead of MIN_PLPMTU for Error state in sctp_transport_pl_send/toobig(), and set packet ipfragok for non-probe packets when it's in Error state. Fixes: 1dc68c194571 ("sctp: do state transition when PROBE_COUNT == MAX_PROBES on HB send path") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-22sctp: do not update transport pathmtu if SPP_PMTUD_ENABLE is not setXin Long1-2/+2
Currently, in sctp_packet_config(), sctp_transport_pmtu_check() is called to update transport pathmtu with dst's mtu when dst's mtu has been changed by non sctp stack like xfrm. However, this should only happen when SPP_PMTUD_ENABLE is set, no matter where dst's mtu changed. This patch is to fix by checking SPP_PMTUD_ENABLE flag before calling sctp_transport_pmtu_check(). Thanks Jacek for reporting and looking into this issue. v1->v2: - add the missing "{" to fix the build error. Fixes: 69fec325a643 ('Revert "sctp: remove sctp_transport_pmtu_check"') Reported-by: Jacek Szafraniec <jacek.szafraniec@nokia.com> Tested-by: Jacek Szafraniec <jacek.szafraniec@nokia.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-22sctp: enable PLPMTUD when the transport is readyXin Long1-1/+2
sctp_transport_pl_reset() is called whenever any of these 3 members in transport is changed: - probe_interval - param_flags & SPP_PMTUD_ENABLE - state == ACTIVE If all are true, start the PLPMTUD when it's not yet started. If any of these is false, stop the PLPMTUD when it's already running. sctp_transport_pl_update() is called when the transport dst has changed. It will restart the PLPMTUD probe. Again, the pathmtu won't change but use the dst's mtu until the Search phase is done. Note that after using PLPMTUD, the pathmtu is only initialized with the dst mtu when the transport dst changes. At other time it is updated by pl.pmtu. So sctp_transport_pmtu_check() will be called only when PLPMTUD is disabled in sctp_packet_config(). After this patch, the PLPMTUD feature from RFC8899 will be activated and can be used by users. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-22sctp: do the basic send and recv for PLPMTUD probeXin Long1-1/+29
This patch does exactly what rfc8899#section-6.2.1.2 says: The SCTP sender needs to be able to determine the total size of a probe packet. The HEARTBEAT chunk could carry a Heartbeat Information parameter that includes, besides the information suggested in [RFC4960], the probe size to help an implementation associate a HEARTBEAT ACK with the size of probe that was sent. The sender could also use other methods, such as sending a nonce and verifying the information returned also contains the corresponding nonce. The length of the PAD chunk is computed by reducing the probing size by the size of the SCTP common header and the HEARTBEAT chunk. Note that HB ACK chunk will carry back whatever HB chunk carried, including the probe_size we put it in; We also check hbinfo->probe_size in the HB ACK against link->pl.probe_size to validate this HB ACK chunk. v1->v2: - Remove the unused 'sp' and add static for sctp_packet_bundle_pad(). Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-19sctp: move sk_route_caps check and set into sctp_outq_flush_transportsXin Long1-7/+0
The sk's sk_route_caps is set in sctp_packet_config, and later it only needs to change when traversing the transport_list in a loop, as the dst might be changed in the tx path. So move sk_route_caps check and set into sctp_outq_flush_transports from sctp_packet_transmit. This also fixes a dst leak reported by Chen Yi: https://bugzilla.kernel.org/show_bug.cgi?id=212227 As calling sk_setup_caps() in sctp_packet_transmit may also set the sk_route_caps for the ctrl sock in a netns. When the netns is being deleted, the ctrl sock's releasing is later than dst dev's deleting, which will cause this dev's deleting to hang and dmesg error occurs: unregister_netdevice: waiting for xxx to become free. Usage count = 1 Reported-by: Chen Yi <yiche@redhat.com> Fixes: bcd623d8e9fa ("sctp: call sk_setup_caps in sctp_packet_transmit instead") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-10-31sctp: support for sending packet over udp4 sockXin Long1-6/+3
This patch does what the rfc6951#section-5.3 says for ipv4: "Within the UDP header, the source port MUST be the local UDP encapsulation port number of the SCTP stack, and the destination port MUST be the remote UDP encapsulation port number maintained for the association and the destination address to which the packet is sent (see Section 5.1). Because the SCTP packet is the UDP payload, the length of the UDP packet MUST be the length of the SCTP packet plus the size of the UDP header. The SCTP checksum MUST be computed for IPv4 and IPv6, and the UDP checksum SHOULD be computed for IPv4 and IPv6." Some places need to be adjusted in sctp_packet_transmit(): 1. For non-gso packets, when transport's encap_port is set, sctp checksum has to be done in sctp_packet_pack(), as the outer udp will use ip_summed = CHECKSUM_PARTIAL to do the offload setting for checksum. 2. Delay calling dst_clone() and skb_dst_set() for non-udp packets until sctp_v4_xmit(), as for udp packets, skb_dst_set() is not needed before calling udp_tunnel_xmit_skb(). then in sctp_v4_xmit(): 1. Go to udp_tunnel_xmit_skb() only when transport->encap_port and net->sctp.udp_port both are set, as these are one for dst port and another for src port. 2. For gso packet, SKB_GSO_UDP_TUNNEL_CSUM is set for gso_type, and with this udp checksum can be done in __skb_udp_tunnel_segment() for each segments after the sctp gso. 3. inner_mac_header and inner_transport_header are set, as these will be needed in __skb_udp_tunnel_segment() to find the right headers. 4. df and ttl are calculated, as these are the required params by udp_tunnel_xmit_skb(). 5. nocheck param has to be false, as "the UDP checksum SHOULD be computed for IPv4 and IPv6", says in rfc6951#section-5.3. v1->v2: - Use sp->udp_port instead in sctp_v4_xmit(), which is more safe. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-31sctp: call sk_setup_caps in sctp_packet_transmit insteadXin Long1-6/+7
sk_setup_caps() was originally called in Commit 90017accff61 ("sctp: Add GSO support"), as: "We have to refresh this in case we are xmiting to more than one transport at a time" This actually happens in the loop of sctp_outq_flush_transports(), and it shouldn't be tied to gso, so move it out of gso part and before sctp_packet_pack(). Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2019-12-10sctp: get netns from asoc and ep baseXin Long1-1/+1
Commit 312434617cb1 ("sctp: cache netns in sctp_ep_common") set netns in asoc and ep base since they're created, and it will never change. It's a better way to get netns from asoc and ep base, comparing to calling sock_net(). This patch is to replace them. v1->v2: - no change. Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-03sctp: count data bundling sack chunk for outctrlchunksXin Long1-0/+3
Now all ctrl chunks are counted for asoc stats.octrlchunks and net SCTP_MIB_OUTCTRLCHUNKS either after queuing up or bundling, other than the chunk maked and bundled in sctp_packet_bundle_sack, which caused 'outctrlchunks' not consistent with 'inctrlchunks' in peer. This issue exists since very beginning, here to fix it by increasing both net SCTP_MIB_OUTCTRLCHUNKS and asoc stats.octrlchunks when sack chunk is maked and bundled in sctp_packet_bundle_sack. Reported-by: Ja Ram Jeon <jajeon@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-24treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104Thomas Gleixner1-16/+1
Based on 1 normalized pattern(s): this sctp implementation is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 or at your option any later version this sctp implementation is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with gnu cc see the file copying if not see http www gnu org licenses extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 42 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Richard Fontana <rfontana@redhat.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190523091649.683323110@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-28sctp: increase sk_wmem_alloc when head->truesize is increasedXin Long1-0/+1
I changed to count sk_wmem_alloc by skb truesize instead of 1 to fix the sk_wmem_alloc leak caused by later truesize's change in xfrm in Commit 02968ccf0125 ("sctp: count sk_wmem_alloc by skb truesize in sctp_packet_transmit"). But I should have also increased sk_wmem_alloc when head->truesize is increased in sctp_packet_gso_append() as xfrm does. Otherwise, sctp gso packet will cause sk_wmem_alloc underflow. Fixes: 02968ccf0125 ("sctp: count sk_wmem_alloc by skb truesize in sctp_packet_transmit") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-19Revert "sctp: remove sctp_transport_pmtu_check"Xin Long1-0/+3
This reverts commit 22d7be267eaa8114dcc28d66c1c347f667d7878a. The dst's mtu in transport can be updated by a non sctp place like in xfrm where the MTU information didn't get synced between asoc, transport and dst, so it is still needed to do the pmtu check in sctp_packet_config. Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-19sctp: count sk_wmem_alloc by skb truesize in sctp_packet_transmitXin Long1-20/+1
Now sctp increases sk_wmem_alloc by 1 when doing set_owner_w for the skb allocked in sctp_packet_transmit and decreases by 1 when freeing this skb. But when this skb goes through networking stack, some subcomponents might change skb->truesize and add the same amount on sk_wmem_alloc. However sctp doesn't know the amount to decrease by, it would cause a leak on sk->sk_wmem_alloc and the sock can never be freed. Xiumei found this issue when it hit esp_output_head() by using sctp over ipsec, where skb->truesize is added and so is sk->sk_wmem_alloc. Since sctp has used sk_wmem_queued to count for writable space since Commit cd305c74b0f8 ("sctp: use sk_wmem_queued to check for writable space"), it's ok to fix it by counting sk_wmem_alloc by skb truesize in sctp_packet_transmit. Fixes: cac2661c53f3 ("esp4: Avoid skb_cow_data whenever possible") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-16sctp: use the pmtu from the icmp packet to update transport pathmtuXin Long1-0/+6
Other than asoc pmtu sync from all transports, sctp_assoc_sync_pmtu is also processing transport pmtu_pending by icmp packets. But it's meaningless to use sctp_dst_mtu(t->dst) as new pmtu for a transport. The right pmtu value should come from the icmp packet, and it would be saved into transport->mtu_info in this patch and used later when the pmtu sync happens in sctp_sendmsg_to_asoc or sctp_packet_config. Besides, without this patch, as pmtu can only be updated correctly when receiving a icmp packet and no place is holding sock lock, it will take long time if the sock is busy with sending packets. Note that it doesn't process transport->mtu_info in .release_cb(), as there is no enough information for pmtu update, like for which asoc or transport. It is not worth traversing all asocs to check pmtu_pending. So unlike tcp, sctp does this in tx path, for which mtu_info needs to be atomic_t. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-14sctp: define sctp_packet_gso_append to build GSO framesXin Long1-10/+18
Now sctp GSO uses skb_gro_receive() to append the data into head skb frag_list. However it actually only needs very few code from skb_gro_receive(). Besides, NAPI_GRO_CB has to be set while most of its members are not needed here. This patch is to add sctp_packet_gso_append() to build GSO frames instead of skb_gro_receive(), and it would avoid many unnecessary checks and make the code clearer. Note that sctp will use page frags instead of frag_list to build GSO frames in another patch. But it may take time, as sctp's GSO frames may have different size. skb_segment() can only split it into the frags with the same size, which would break the border of sctp chunks. Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: remove sctp_transport_pmtu_checkMarcelo Ricardo Leitner1-3/+0
We are now keeping the MTU information synced between asoc, transport and dst, which makes the check at sctp_packet_config() not needed anymore. As it was the sole caller to this function, lets remove it. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-27sctp: introduce sctp_mtu_payloadMarcelo Ricardo Leitner1-15/+10
When given a MTU, this function calculates how much payload we can carry on it. Without a MTU, it calculates the amount of header overhead we have. So that when we have extra overhead, like the one added for IP options on SELinux patches, it is easier to handle it. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-07Merge tag 'selinux-pr-20180403' of ↵Linus Torvalds1-13/+21
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux Pull SELinux updates from Paul Moore: "A bigger than usual pull request for SELinux, 13 patches (lucky!) along with a scary looking diffstat. Although if you look a bit closer, excluding the usual minor tweaks/fixes, there are really only two significant changes in this pull request: the addition of proper SELinux access controls for SCTP and the encapsulation of a lot of internal SELinux state. The SCTP changes are the result of a multi-month effort (maybe even a year or longer?) between the SELinux folks and the SCTP folks to add proper SELinux controls. A special thanks go to Richard for seeing this through and keeping the effort moving forward. The state encapsulation work is a bit of janitorial work that came out of some early work on SELinux namespacing. The question of namespacing is still an open one, but I believe there is some real value in the encapsulation work so we've split that out and are now sending that up to you" * tag 'selinux-pr-20180403' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux: selinux: wrap AVC state selinux: wrap selinuxfs state selinux: fix handling of uninitialized selinux state in get_bools/classes selinux: Update SELinux SCTP documentation selinux: Fix ltp test connect-syscall failure selinux: rename the {is,set}_enforcing() functions selinux: wrap global selinux state selinux: fix typo in selinux_netlbl_sctp_sk_clone declaration selinux: Add SCTP support sctp: Add LSM hooks sctp: Add ip option support security: Add support for SCTP security hooks netlabel: If PF_INET6, check sk_buff ip header version
2018-03-14sctp: add refcnt support for sh_keyXin Long1-2/+16
With refcnt support for sh_key, chunks auth sh_keys can be decided before enqueuing it. Changing the active key later will not affect the chunks already enqueued. Furthermore, this is necessary when adding the support for authinfo for sendmsg in next patch. Note that struct sctp_chunk can't be grown due to that performance drop issue on slow cpu, so it just reuses head_skb memory for shkey in sctp_chunk. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-27sctp: Add ip option supportRichard Haines1-13/+21
Add ip option support to allow LSM security modules to utilise CIPSO/IPv4 and CALIPSO/IPv6 services. Signed-off-by: Richard Haines <richard_c_haines@btinternet.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com>
2017-12-11sctp: implement assign_number for sctp_stream_interleaveXin Long1-2/+3
assign_number is added as a member of sctp_stream_interleave, used to assign ssn for data or mid (message id) for idata, called in sctp_packet_append_data. sctp_chunk_assign_ssn is left as it is, and sctp_chunk_assign_mid is added for sctp_stream_interleave_1. This procedure is described in section 2.2.2 of RFC8260. All sizeof(struct sctp_data_chunk) in tx path is replaced with sctp_datachk_len, to make it right for idata as well. And also adjust sctp_chunk_is_data for SCTP_CID_I_DATA. After this patch, idata can be built and sent in tx path. Note that if sp strm_interleave is set, it has to wait_connect in sctp_sendmsg, as asoc intl_enable need to be known after 4 shake- hands, to decide if it should use data or idata later. data and idata can't be mixed to send in one asoc. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-07sctp: remove the typedef sctp_xmit_tXin Long1-30/+30
This patch is to remove the typedef sctp_xmit_t, and replace with enum sctp_xmit in the places where it's using this typedef. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-01sctp: remove the typedef sctp_data_chunk_tXin Long1-2/+2
This patch is to remove the typedef sctp_data_chunk_t, and replace with struct sctp_data_chunk in the places where it's using this typedef. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-01net: convert sock.sk_wmem_alloc from atomic_t to refcount_tReshetova, Elena1-1/+1
refcount_t type and corresponding API should be used instead of atomic_t when the variable is used as a reference counter. This allows to avoid accidental refcounter overflows that might lead to use-after-free situations. Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: make skb_push & __skb_push return void pointersJohannes Berg1-1/+1
It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) @@ expression SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - fn(SKB, LEN)[0] + *(u8 *)fn(SKB, LEN) Note that the last part there converts from push(...)[0] to the more idiomatic *(u8 *)push(...). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: introduce and use skb_put_data()Johannes Berg1-2/+1
A common pattern with skb_put() is to just want to memcpy() some data into the new space, introduce skb_put_data() for this. An spatch similar to the one for skb_put_zero() converts many of the places using it: @@ identifier p, p2; expression len, skb, data; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_data(skb, data, len); | -p = (t)skb_put(skb, len); +p = skb_put_data(skb, data, len); ) ( p2 = (t2)p; -memcpy(p2, data, len); | -memcpy(p, data, len); ) @@ type t, t2; identifier p, p2; expression skb, data; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_data(skb, data, sizeof(t)); ) ( p2 = (t2)p; -memcpy(p2, data, sizeof(*p)); | -memcpy(p, data, sizeof(*p)); ) @@ expression skb, len, data; @@ -memcpy(skb_put(skb, len), data, len); +skb_put_data(skb, data, len); (again, manually post-processed to retain some comments) Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: convert many more places to skb_put_zero()Johannes Berg1-1/+1
There were many places that my previous spatch didn't find, as pointed out by yuan linyu in various patches. The following spatch found many more and also removes the now unnecessary casts: @@ identifier p, p2; expression len; expression skb; type t, t2; @@ ( -p = skb_put(skb, len); +p = skb_put_zero(skb, len); | -p = (t)skb_put(skb, len); +p = skb_put_zero(skb, len); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, len); | -memset(p, 0, len); ) @@ type t, t2; identifier p, p2; expression skb; @@ t *p; ... ( -p = skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); | -p = (t *)skb_put(skb, sizeof(t)); +p = skb_put_zero(skb, sizeof(t)); ) ... when != p ( p2 = (t2)p; -memset(p2, 0, sizeof(*p)); | -memset(p, 0, sizeof(*p)); ) @@ expression skb, len; @@ -memset(skb_put(skb, len), 0, len); +skb_put_zero(skb, len); Apply it to the tree (with one manual fixup to keep the comment in vxlan.c, which spatch removed.) Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-20net: use skb->csum_not_inet to identify packets needing crc32cDavide Caratti1-0/+1
skb->csum_not_inet carries the indication on which algorithm is needed to compute checksum on skb in the transmit path, when skb->ip_summed is equal to CHECKSUM_PARTIAL. If skb carries a SCTP packet and crc32c hasn't been yet written in L4 header, skb->csum_not_inet is assigned to 1; otherwise, assume Internet Checksum is needed and thus set skb->csum_not_inet to 0. Suggested-by: Tom Herbert <tom@herbertland.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-05sctp: get sock from transport in sctp_transport_update_pmtuXin Long1-2/+2
This patch is almost to revert commit 02f3d4ce9e81 ("sctp: Adjust PMTU updates to accomodate route invalidation."). As t->asoc can't be NULL in sctp_transport_update_pmtu, it could get sk from asoc, and no need to pass sk into that function. It is also to remove some duplicated codes from that function. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-04sctp: check for dst and pathmtu update in sctp_packet_configXin Long1-31/+36
This patch is to move sctp_transport_dst_check into sctp_packet_config from sctp_packet_transmit and add pathmtu check in sctp_packet_config. With this fix, sctp can update dst or pathmtu before appending chunks, which can void dropping packets in sctp_packet_transmit when dst is obsolete or dst's mtu is changed. This patch is also to improve some other codes in sctp_packet_config. It updates packet max_size with gso_max_size, checks for dst and pathmtu, and appends ecne chunk only when packet is empty and asoc is not NULL. It makes sctp flush work better, as we only need to set up them once for one flush schedule. It's also safe, since asoc is NULL only when the packet is created by sctp_ootb_pkt_new in which it just gets the new dst, no need to do more things for it other than set packet with transport's pathmtu. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-29sctp: change to save MSG_MORE flag into assocXin Long1-1/+1
David Laight noticed the support for MSG_MORE with datamsg->force_delay didn't really work as we expected, as the first msg with MSG_MORE set would always block the following chunks' dequeuing. This Patch is to rewrite it by saving the MSG_MORE flag into assoc as David Laight suggested. asoc->force_delay is used to save MSG_MORE flag before a msg is sent. All chunks in queue would not be sent out if asoc->force_delay is set by the msg with MSG_MORE flag, until a new msg without MSG_MORE flag clears asoc->force_delay. Note that this change would not affect the flush is generated by other triggers, like asoc->state != ESTABLISHED, queue size > pmtu etc. v1->v2: Not clear asoc->force_delay after sending the msg with MSG_MORE flag. Fixes: 4ea0c32f5f42 ("sctp: add support for MSG_MORE") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: David Laight <david.laight@aculab.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-22sctp: remove temporary variable confirm from sctp_packet_transmitXin Long1-4/+3
Commit c86a773c7802 ("sctp: add dst_pending_confirm flag") introduced a temporary variable "confirm" in sctp_packet_transmit. But it broke the rule that longer lines should be above shorter ones. Besides, this variable is not necessary, so this patch is to just remove it and use tp->dst_pending_confirm directly. Fixes: c86a773c7802 ("sctp: add dst_pending_confirm flag") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-28lib/vsprintf.c: remove %Z supportAlexey Dobriyan1-1/+1
Now that %z is standartised in C99 there is no reason to support %Z. Unlike %L it doesn't even make format strings smaller. Use BUILD_BUG_ON in a couple ATM drivers. In case anyone didn't notice lib/vsprintf.o is about half of SLUB which is in my opinion is quite an achievement. Hopefully this patch inspires someone else to trim vsprintf.c more. Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2 Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-02-20sctp: add support for MSG_MOREXin Long1-6/+3
This patch is to add support for MSG_MORE on sctp. It adds force_delay in sctp_datamsg to save MSG_MORE, and sets it after creating datamsg according to the send flag. sctp_packet_can_append_data then uses it to decide if the chunks of this msg will be sent at once or delay it. Note that unlike [1], this patch saves MSG_MORE in datamsg, instead of in assoc. As sctp enqueues the chunks first, then dequeue them one by one. If it's saved in assoc,the current msg's send flag (MSG_MORE) may affect other chunks' bundling. Since last patch, sctp flush out queue once assoc state falls into SHUTDOWN_PENDING, the close block problem mentioned in [1] has been solved as well. [1] https://patchwork.ozlabs.org/patch/372404/ Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-07sctp: add dst_pending_confirm flagJulian Anastasov1-1/+9
Add new transport flag to allow sockets to confirm neighbour. When same struct dst_entry can be used for many different neighbours we can not use it for pending confirmations. The flag is propagated from transport to every packet. It is reset when cached dst is reset. Reported-by: YueHaibing <yuehaibing@huawei.com> Fixes: 5110effee8fd ("net: Do delayed neigh confirmation.") Fixes: f2bb4bedf35d ("ipv4: Cache output routes in fib_info nexthops.") Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-12-28sctp: remove return value from sctp_packet_init/configMarcelo Ricardo Leitner1-9/+5
There is no reason to use this cascading. It doesn't add anything. Let's remove it and simplify. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-02sctp: clean up sctp_packet_transmitXin Long1-277/+158
After adding sctp gso, sctp_packet_transmit is a quite big function now. This patch is to extract the codes for packing packet to sctp_packet_pack from sctp_packet_transmit, and add some comments, simplify the err path by freeing auth chunk when freeing packet chunk_list in out path and freeing head skb early if it fails to pack packet. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller1-1/+7
Mostly simple overlapping changes. For example, David Ahern's adjacency list revamp in 'net-next' conflicted with an adjacency list traversal bug fix in 'net'. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-27sctp: fix the panic caused by route updateXin Long1-1/+7
Commit 7303a1475008 ("sctp: identify chunks that need to be fragmented at IP level") made the chunk be fragmented at IP level in the next round if it's size exceed PMTU. But there still is another case, PMTU can be updated if transport's dst expires and transport's pmtu_pending is set in sctp_packet_transmit. If the new PMTU is less than the chunk, the same issue with that commit can be triggered. So we should drop this packet and let it retransmit in another round where it would be fragmented at IP level. This patch is to fix it by checking the chunk size after PMTU may be updated and dropping this packet if it's size exceed PMTU. Fixes: 90017accff61 ("sctp: Add GSO support") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@txudriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-13sctp: remove the old ttl expires policyXin Long1-3/+0
The prsctp polices include ttl expires policy already, we should remove the old ttl expires codes, and just adjust the new polices' codes to be compatible with the old one for users. This patch is to remove all the old expires codes, and if prsctp polices are not set, it will still set msg's expires_at and check the expires in sctp_check_abandoned. Note that asoc->prsctp_enable is set by default, so users can't feel any difference even if they use the old expires api in userspace. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-13sctp: reuse sent_count to avoid retransmitted chunks for RTT measurementsXin Long1-1/+2
Now sctp uses chunk->resent to record if a chunk is retransmitted, for RTT measurements with retransmitted DATA chunks. chunk->sent_count was introduced to record how many times one chunk has been sent for prsctp RTX policy before. We actually can know if one chunk is retransmitted by checking chunk->sent_count is greater than 1. This patch is to remove resent from sctp_chunk and reuse sent_count to avoid retransmitted chunks for RTT measurements. Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-22sctp: rename WORD_TRUNC/ROUND macrosMarcelo Ricardo Leitner1-6/+6
To something more meaningful these days, specially because this is working on packet headers or lengths and which are not tied to any CPU arch but to the protocol itself. So, WORD_TRUNC becomes SCTP_TRUNC4 and WORD_ROUND becomes SCTP_PAD4. Reported-by: David Laight <David.Laight@ACULAB.COM> Reported-by: David Miller <davem@davemloft.net> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-19sctp: not return ENOMEM err back in sctp_packet_transmitXin Long1-25/+22
As David and Marcelo's suggestion, ENOMEM err shouldn't return back to user in transmit path. Instead, sctp's retransmit would take care of the chunks that fail to send because of ENOMEM. This patch is only to do some release job when alloc_skb fails, not to return ENOMEM back any more. Besides, it also cleans up sctp_packet_transmit's err path, and fixes some issues in err path: - It didn't free the head skb in nomem: path. - No need to check nskb in no_route: path. - It should goto err: path if alloc_skb fails for head. - Not all the NOMEMs should free nskb. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-19sctp: save transmit error to sk_err in sctp_outq_flushXin Long1-1/+2
Every time when sctp calls sctp_outq_flush, it sends out the chunks of control queue, retransmit queue and data queue. Even if some trunks are failed to transmit, it still has to flush all the transports, as it's the only chance to clean that transmit_list. So the latest transmit error here should be returned back. This transmit error is an internal error of sctp stack. I checked all the places where it uses the transmit error (the return value of sctp_outq_flush), most of them are actually just save it to sk_err. Except for sctp_assoc/endpoint_bh_rcv, they will drop the chunk if it's failed to send a REPLY, which is actually incorrect, as we can't be sure the error that sctp_outq_flush returns is from sending that REPLY. So it's meaningless for sctp_outq_flush to return error back. This patch is to save transmit error to sk_err in sctp_outq_flush, the new error can update the old value. Eventually, sctp_wait_for_* would check for it. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-10sctp: identify chunks that need to be fragmented at IP levelMarcelo Ricardo Leitner1-1/+12
Previously, without GSO, it was easy to identify it: if the chunk didn't fit and there was no data chunk in the packet yet, we could fragment at IP level. So if there was an auth chunk and we were bundling a big data chunk, it would fragment regardless of the size of the auth chunk. This also works for the context of PMTU reductions. But with GSO, we cannot distinguish such PMTU events anymore, as the packet is allowed to exceed PMTU. So we need another check: to ensure that the chunk that we are adding, actually fits the current PMTU. If it doesn't, trigger a flush and let it be fragmented at IP level in the next round. Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-31sctp: fix the issue sctp requeue auth chunk incorrectlyXin Long1-1/+2
sctp needs to queue auth chunk back when we know that we are going to generate another segment. But commit f1533cce60d1 ("sctp: fix panic when sending auth chunks") requeues the last chunk processed which is probably not the auth chunk. It causes panic when calculating the MAC in sctp_auth_calculate_hmac(), as the incorrect offset of the auth chunk in skb->data. This fix is to requeue it by using packet->auth. Fixes: f1533cce60d1 ("sctp: fix panic when sending auth chunks") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-11sctp: implement prsctp TTL policyXin Long1-0/+2
prsctp TTL policy is a policy to abandon chunks when they expire at the specific time in local stack. It's similar with expires_at in struct sctp_datamsg. This patch uses sinfo->sinfo_timetolive to set the specific time for TTL policy. sinfo->sinfo_timetolive is also used for msg->expires_at. So if prsctp_enable or TTL policy is not enabled, msg->expires_at still works as before. Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-07-09sctp: fix panic when sending auth chunksMarcelo Ricardo Leitner1-3/+15
When we introduced GSO support, if using auth the auth chunk was being left queued on the packet even after the final segment was generated. Later on sctp_transmit_packet it calls sctp_packet_reset, which zeroed the packet len while not accounting for this left-over. This caused more space to be used the next packet due to the chunk still being queued, but space which wasn't allocated as its size wasn't accounted. The fix is to only queue it back when we know that we are going to generate another segment. Fixes: 90017accff61 ("sctp: Add GSO support") Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>