Age | Commit message (Collapse) | Author | Files | Lines |
|
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remove all the code that was there to configure WDS interfaces,
now that there's no way to reach it anymore.
Link: https://lore.kernel.org/r/20201109105103.8f5b98e4068d.I5f5129041649ef2862b69683574bb3344743727b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As discovered by syzbot, cfg80211 was accepting S1G
channel widths on non-S1G bands. Add a check for this, and
consolidate the 1MHz frequency check as it ends up being a
subset of the others.
Reported-by: syzbot+92715a0eccd6c881bc32@syzkaller.appspotmail.com
Fixes: 11b34737b18a ("nl80211: support setting S1G channels")
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005165122.17583-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
S1G channels have a single width defined per frequency, so
derive it from the channel flags with
ieee80211_s1g_channel_width().
Also support setting an S1G channel where control frequency may
differ from operating, and add some basic validation to
ensure the control channel is with the operating.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200908190323.15814-6-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
|
|
Fix cfg80211_chandef_usable():
consider IEEE80211_VHT_CAP_EXT_NSS_BW when verifying 160/80+80 MHz.
Based on:
"Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW
Support subfield at a STA transmitting the VHT Capabilities Information field"
From "Draft P802.11REVmd_D3.0.pdf"
Signed-off-by: Aviad Brikman <aviad.brikman@celeno.com>
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20200826143139.25976-1-shay.bar@celeno.com
[reformat the code a bit and use u32_get_bits()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Gives drivers the definitions needed to advertise support
for S1G bands.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com
Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a 6 GHz channel exists, then we can probably safely assume that
the device actually supports it, and then it should support most
bandwidths.
This will probably need to be extended to check the interface type
and then dig into the HE capabilities for that though, to have the
correct bandwidth check.
Link: https://lore.kernel.org/r/20200528213443.d4864ef52e92.I82f09b2b14a56413ce20376d09967fe954a033eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This should be covered by the next MHz, make sure that the
numbers are always normalized.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200424120103.12b91ecf75f9.I4bf499d58404283bbfacb517d614a816763bccf2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:
MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
Also provide some helper functions to do the frequency
conversion and test for equality.
Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.
Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.
mesh, ibss, wext, etc. are currently ignored.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch disables setting of HT20 and more for channel 14 because
the channel is only for IEEE 802.11b.
The patch for net/wireless/util.c was unit-tested.
The patch for net/wireless/chan.c was tested with iw command.
Before this patch.
$ sudo iw dev <ifname> set channel 14 HT20
$
After this patch.
$ sudo iw dev <ifname> set channel 14 HT20
kernel reports: invalid channel definition
command failed: Invalid argument (-22)
$
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Link: https://lore.kernel.org/r/20191021075045.2719-1-masashi.honma@gmail.com
[clean up the code, use != instead of equivalent >]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function cfg80211_ir_permissive_chan() is applicable for
6GHz band as well so make sure it is handled.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-7-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are talks about enabling -Wimplicit-fallthrough warnings in the
mainline and it is already enabled in linux-next. Add all the
missing annotations to prevent warnings when this happens.
And in one case, remove the extra text from the annotation so that the
compiler recognizes it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently channel switch/start_ap to DFS channel cannot be done to
non-CAC-cleared channel even if DFS offload if enabled.
Make non-cleared DFS channels available if DFS offload is enabled.
CAC will be started by HW after channel change, start_ap call, etc.
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Perhaps it had been intended to be used, but it clearly isn't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sharing DFS channel state across multiple wiphys (radios) could
be useful with multiple radios on the system. When one radio
completes CAC and markes the channel available another radio
can use this information and start beaconing without really doing
CAC.
Whenever there is a state change in dfs channel associated to
a particular wiphy the the same state change is propagated to
other wiphys having the same DFS reg domain configuration.
Also when a new wiphy is created the dfs channel state of
other existing wiphys of same DFS domain is copied.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
DFS requirement for ETSI domain (section 4.7.1.4 in
ETSI EN 301 893 V1.8.1) is the only one which explicitly
states that once DFS channel is marked as available afer
the CAC, this channel will remain in available state even
moving to a different operating channel. But the same is
not explicitly stated in FCC DFS requirement. Also, Pre-CAC
requriements are not explicitly mentioned in FCC requirement.
Current implementation in keeping DFS channel in available
state is same as described in ETSI domain.
For non-ETSI DFS domain, this patch gives a grace period of 2 seconds
since the completion of successful CAC before moving the channel's
DFS state to 'usable' from 'available' state. The same grace period
is checked against the channel's dfs_state_entered timestamp while
deciding if a DFS channel is available for operation. There is a new
radar event, NL80211_RADAR_PRE_CAC_EXPIRED, reported when DFS channel
is moved from available to usable state after the grace period. Also
make sure the DFS channel state is reset to usable once the beaconing
operation on that channel is brought down (like stop_ap, leave_ibss
and leave_mesh) in non-ETSI domain.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows user space to start/stop NAN interface.
A NAN interface is like P2P device in a few aspects: it
doesn't have a netdev associated to it.
Add the new interface type and prevent operations that
can't be executed on NAN interface like scan.
Define several attributes that may be configured by user space
when starting NAN functionality (master preference and dual
band operation)
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
|
|
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The switch on chandef->width is missing a break on the
NL8211_CHAN_WIDTH_80P80 case; currently we get a WARN_ON when
center_freq2 is non-zero because of the missing break.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The RTNL is required to check for IR-relaxation conditions that allow
more channels to beacon. Export an RTNL locked version of reg_can_beacon
and use it where possible in AP/STA interface type flows, where
IR-relaxation may be applicable.
Fixes: 06f207fc5418 ("cfg80211: change GO_CONCURRENT to IR_CONCURRENT for STA")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The GO_CONCURRENT regulatory definition can be extended to station
interfaces requesting to IR as part of TDLS off-channel operations.
Rename the GO_CONCURRENT flag to IR_CONCURRENT and allow the added
use-case.
Change internal users of GO_CONCURRENT to use the new definition.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a P2P GO was allowed on a channel because of the GO concurrent
relaxation, i.e., another station interface was associated to an AP on
the same channel or the same UNII band, and the station interface
disconnected from the AP, allow the following use cases unless the
channel is marked as indoor only and the device is not operating in an
indoor environment:
1. Allow the P2P GO to stay on its current channel. The rationale behind
this is that if the channel or UNII band were allowed by the AP they
could still be used to continue the P2P GO operation, and avoid connection
breakage.
2. Allow another P2P GO to start on the same channel or another channel
that is in the same UNII band as the previous instantiated P2P GO.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The VHT supported channel width field is a two bit integer, not a
bitfield. cfg80211_chandef_usable() was interpreting it incorrectly and
ended up rejecting 160 MHz channel width if the driver indicated support
for both 160 and 80+80 MHz channels.
Cc: stable@vger.kernel.org (3.16+)
Fixes: 3d9d1d6656a73 ("nl80211/cfg80211: support VHT channel configuration")
(however, no real drivers had 160 MHz support it until 3.16)
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The helper function can't ever create negative values, so use
u32 pointers as the function arguments as the caller does.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There is no need to pass NL80211_IFTYPE_UNSPECIFIED when calling
cfg80211_chandef_dfs_required() since we always already have the
interface type. So, pass the actual interface type instead.
Additionally, have cfg80211_chandef_dfs_required() WARN if the passed
interface type is NL80211_IFTYPE_UNSPECIFIED, so we can detect
problems more easily.
Tested-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After patch:
cfg80211/mac80211: refactor cfg80211_chandef_dfs_required()
start_radar_detection always fail with -EINVAL.
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since there are frequency bands (e.g. 5.9GHz) allowing channels
with only 10 or 5 MHz bandwidth, this patch adds attributes that
allow keeping track about this information.
When channel attributes are reported to user-space, make sure to
not break old tools, i.e. if the 'split wiphy dump' is enabled,
report the extra attributes (if present) describing the bandwidth
restrictions. If the 'split wiphy dump' is not enabled,
completely omit those channels that have flags set to either
IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ.
Add the check for new bandwidth restriction flags in
cfg80211_chandef_usable() to comply with the restrictions.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Name wiphy_to_rdev is more accurate to describe what the function
does, i.e., return a pointer pointing to struct
cfg80211_registered_device.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
At some locations, channels 149-165 are considered a single
bundle, while at some other locations, e.g., Indonesia, channels
149-161 are considered a single bundle, while channel 165 belongs
to a different bundle. This means that:
1. A station interface connection to an AP on channel 165 allows
the instantiation of a P2P GO on channels 149-165.
2. A station interface connection to an AP on channels 149-161
does NOT allow the instantiation of a P2P GO on channel 165.
Fix this.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some interface types don't require DFS (such as STATION, P2P_CLIENT
etc). In order to centralize these decisions, make
cfg80211_chandef_dfs_required() take the iftype into consideration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow GO operation on a channel marked with IEEE80211_CHAN_INDOOR_ONLY
iff there is a user hint indicating that the platform is operating in
an indoor environment, i.e., the platform is a printer or media center
device.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow GO operation on a channel marked with IEEE80211_CHAN_GO_CONCURRENT
iff there is an active station interface that is associated to
an AP operating on the same channel in the 2 GHz band or the same UNII band
(in the 5 GHz band). This relaxation is not allowed if the channel is
marked with IEEE80211_CHAN_RADAR.
Note that this is a permissive approach to the FCC definitions,
that require a clear assessment that the device operating the AP is
an authorized master, i.e., with radar detection and DFS capabilities.
It is assumed that such restrictions are enforced by user space.
Furthermore, it is assumed, that if the conditions that allowed for
the operation of the GO on such a channel change, i.e., the station
interface disconnected from the AP, it is the responsibility of user
space to evacuate the GO from the channel.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
|
|
Send Channel Availability Check time as a parameter
of start_radar_detection() callback.
Get CAC time from regulatory database.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.
I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no driver using this flag and consequently no userspace
application is actually looking at it. As it seems unlikely for
any driver to start using it, remove it and the (very little)
code that used it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It was possible to break interface combinations in
the following way:
combo 1: iftype = AP, num_ifaces = 2, num_chans = 2,
combo 2: iftype = AP, num_ifaces = 1, num_chans = 1, radar = HT20
With the above interface combinations it was
possible to:
step 1. start AP on DFS channel by matching combo 2
step 2. start AP on non-DFS channel by matching combo 1
This was possible beacuse (step 2) did not consider
if other interfaces require radar detection.
The patch changes how cfg80211 tracks channels -
instead of channel itself now a complete chandef
is stored.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow beconing after we pass Channel Availability Check (CAC).
Allow non-DFS and DFS channels mix. All DFS channels have to
be in NL80211_DFS_AVAILABLE state (pass CAC).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|