Age | Commit message (Collapse) | Author | Files | Lines |
|
My previous fix here to fix the deadlock left a race where
the exact same deadlock (see the original commit referenced
below) can still happen if cfg80211_destroy_ifaces() already
runs while nl80211_netlink_notify() is still marking some
interfaces as nl_owner_dead.
The race happens because we have two loops here - first we
dev_close() all the netdevs, and then we destroy them. If we
also have two netdevs (first one need only be a wdev though)
then we can find one during the first iteration, close it,
and go to the second iteration -- but then find two, and try
to destroy also the one we didn't close yet.
Fix this by only iterating once.
Reported-by: Toke Høiland-Jørgensen <toke@redhat.com>
Fixes: ea6b2098dd02 ("cfg80211: fix locking in netlink owner interface destruction")
Tested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20220201130951.22093-1-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently cfg80211 checks for invalid channels whenever there is a
regulatory update and stops the active interfaces if it is operating on
an unsupported channel in the new regulatory domain.
This is done based on a regulatory flag REGULATORY_IGNORE_STALE_KICKOFF
set during wiphy registration which disables this enforcement when
unsupported interface modes are supported by driver.
Add support to enable this enforcement when Mesh Point interface type
is advertised by drivers.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1638409120-28997-1-git-send-email-quic_srirrama@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
confusion with ETSI standard
ETSI standard defines "Offchannel CAC" as:
"Off-Channel CAC is performed by a number of non-continuous checks
spread over a period in time. This period, which is required to
determine the presence of radar signals, is defined as the Off-Channel
CAC Time..
Minimum Off-Channel CAC Time 6 minutes and Maximum Off-Channel CAC Time
4 hours..".
mac80211 implementation refers to a dedicated hw chain used for continuous
radar monitoring. Rename offchannel_* references to background_* in
order to avoid confusion with ETSI standard.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/4204cc1d648d76b44557981713231e030a3bd991.1638190762.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to make cfg80211_offchan_cac_abort() (renamed from
cfg80211_offchan_cac_event) callable in other contexts and
without so much locking restrictions, make it trigger a new
work instead of operating directly.
Do some other renames while at it to clarify.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/6145c3d0f30400a568023f67981981d24c7c6133.1635325205.git.lorenzo@kernel.org
[rewrite commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If a dedicated (off-channel) radar detection hardware (chain)
is available in the hardware/driver, allow this to be used by
calling the NL80211_CMD_RADAR_DETECT command with a new flag
attribute requesting off-channel radar detection is used.
Offchannel CAC (channel availability check) avoids the CAC
downtime when switching to a radar channel or when turning on
the AP.
Drivers advertise support for this using the new feature flag
NL80211_EXT_FEATURE_RADAR_OFFCHAN.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/7468e291ef5d05d692c1738d25b8f778d8ea5c3f.1634979655.git.lorenzo@kernel.org
Link: https://lore.kernel.org/r/1e60e60fef00e14401adae81c3d49f3e5f307537.1634979655.git.lorenzo@kernel.org
Link: https://lore.kernel.org/r/85fa50f57fc3adb2934c8d9ca0be30394de6b7e8.1634979655.git.lorenzo@kernel.org
Link: https://lore.kernel.org/r/4b6c08671ad59aae0ac46fc94c02f31b1610eb72.1634979655.git.lorenzo@kernel.org
Link: https://lore.kernel.org/r/241849ccaf2c228873c6f8495bf87b19159ba458.1634979655.git.lorenzo@kernel.org
[remove offchan_mutex, fix cfg80211_stop_offchan_radar_detection(),
remove gfp_t argument, fix documentation, fix tracing]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
include/net/sock.h
7b50ecfcc6cd ("net: Rename ->stream_memory_read to ->sock_is_readable")
4c1e34c0dbff ("vsock: Enable y2038 safe timeval for timeout")
drivers/net/ethernet/marvell/octeontx2/af/rvu_debugfs.c
0daa55d033b0 ("octeontx2-af: cn10k: debugfs for dumping LMTST map table")
e77bcdd1f639 ("octeontx2-af: Display all enabled PF VF rsrc_alloc entries.")
Adjacent code addition in both cases, keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The management registrations locking was broken, the list was
locked for each wdev, but cfg80211_mgmt_registrations_update()
iterated it without holding all the correct spinlocks, causing
list corruption.
Rather than trying to fix it with fine-grained locking, just
move the lock to the wiphy/rdev (still need the list on each
wdev), we already need to hold the wdev lock to change it, so
there's no contention on the lock in any case. This trivially
fixes the bug since we hold one wdev's lock already, and now
will hold the lock that protects all lists.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Fixes: 6cd536fe62ef ("cfg80211: change internal management frame registration API")
Link: https://lore.kernel.org/r/20211025133111.5cf733eab0f4.I7b0abb0494ab712f74e2efcd24bb31ac33f7eee9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the (somewhat unlikely) event that we allocate a wiphy, then
add a regdomain to it, and then fail registration, we leak the
regdomain. Fix this by just always freeing it at the end, in the
normal cases we'll free (and NULL) it during wiphy_unregister().
This happened when the wiphy settings were bad, and since they
can be controlled by userspace with hwsim, syzbot was able to
find this issue.
Reported-by: syzbot+1638e7c770eef6b6c0d0@syzkaller.appspotmail.com
Fixes: 3e0c3ff36c4c ("cfg80211: allow multiple driver regulatory_hints()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20210927131105.68b70cef4674.I4b9f0aa08c2af28555963b9fe3d34395bb72e0cc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We used to set regulatory info before the registration of
the device and then the regulatory info didn't get set, because
the device isn't registered so there isn't a device to set the
regulatory info for. So set the regulatory info after the device
registration.
Call reg_process_self_managed_hints() once again after the device
registration because it does nothing before it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.c96eadcffe80.I86799c2c866b5610b4cf91115c21d8ceb525c5aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will allow the low level driver to query the rfkill
state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210616202826.9833-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We no longer need to put any limits here, hardware will and
mac80211-hwsim can do whatever it likes. The reason we had
this was some accounting code (still mentioned in the comment)
but that code was deleted in commit c781944b71f8 ("cfg80211:
Remove unused cfg80211_can_use_iftype_chan()").
Link: https://lore.kernel.org/r/20210506221159.d1d61db1d31c.Iac4da68d54b9f1fdc18a03586bbe06aeb9515425@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When I moved around the code here, I neglected that we could still
call register_netdev() or similar without the wiphy mutex held,
which then calls cfg80211_register_wdev() - that's also done from
cfg80211_register_netdevice(), but the phy80211 symlink creation
was only there. Now, the symlink isn't needed for a *pure* wdev,
but a netdev not registered via cfg80211_register_wdev() should
still have the symlink, so move the creation to the right place.
Cc: stable@vger.kernel.org
Fixes: 2fe8ef106238 ("cfg80211: change netdev registration/unregistration semantics")
Link: https://lore.kernel.org/r/20210608113226.a5dc4c1e488c.Ia42fe663cefe47b0883af78c98f284c5555bbe5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
|
|
Harald Arnesen reported [1] a deadlock at reboot time, and after
he captured a stack trace a picture developed of what's going on:
The distribution he's using is using iwd (not wpa_supplicant) to
manage wireless. iwd will usually use the "socket owner" option
when it creates new interfaces, so that they're automatically
destroyed when it quits (unexpectedly or otherwise). This is also
done by wpa_supplicant, but it doesn't do it for the normal one,
only for additional ones, which is different with iwd.
Anyway, during shutdown, iwd quits while the netdev is still UP,
i.e. IFF_UP is set. This causes the stack trace that Linus so
nicely transcribed from the pictures:
cfg80211_destroy_iface_wk() takes wiphy_lock
-> cfg80211_destroy_ifaces()
->ieee80211_del_iface
->ieeee80211_if_remove
->cfg80211_unregister_wdev
->unregister_netdevice_queue
->dev_close_many
->__dev_close_many
->raw_notifier_call_chain
->cfg80211_netdev_notifier_call
and that last call tries to take wiphy_lock again.
In commit a05829a7222e ("cfg80211: avoid holding the RTNL when
calling the driver") I had taken into account the possibility of
recursing from cfg80211 into cfg80211_netdev_notifier_call() via
the network stack, but only for NETDEV_UNREGISTER, not for what
happens here, NETDEV_GOING_DOWN and NETDEV_DOWN notifications.
Additionally, while this worked still back in commit 78f22b6a3a92
("cfg80211: allow userspace to take ownership of interfaces"), it
missed another corner case: unregistering a netdev will cause
dev_close() to be called, and thus stop wireless operations (e.g.
disconnecting), but there are some types of virtual interfaces in
wifi that don't have a netdev - for that we need an additional
call to cfg80211_leave().
So, to fix this mess, change cfg80211_destroy_ifaces() to not
require the wiphy_lock(), but instead make it acquire it, but
only after it has actually closed all the netdevs on the list,
and then call cfg80211_leave() as well before removing them
from the driver, to fix the second issue. The locking change in
this requires modifying the nl80211 call to not get the wiphy
lock passed in, but acquire it by itself after flushing any
potentially pending destruction requests.
[1] https://lore.kernel.org/r/09464e67-f3de-ac09-28a3-e27b7914ee7d@skogtun.org
Cc: stable@vger.kernel.org # 5.12
Reported-by: Harald Arnesen <harald@skogtun.org>
Fixes: 776a39b8196d ("cfg80211: call cfg80211_destroy_ifaces() with wiphy lock held")
Fixes: 78f22b6a3a92 ("cfg80211: allow userspace to take ownership of interfaces")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Harald Arnesen <harald@skogtun.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
rfkill now allows to report a reason for the hw_rfkill state.
Allow cfg80211 drivers to specify this reason.
Keep the current API to use the default reason
(RFKILL_HARD_BLOCK_SIGNAL).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210322204633.102581-4-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Here is only one place where we want to specify new_ifindex. In all
other cases, callers pass 0 as new_ifindex. It looks reasonable to add a
low-level function with new_ifindex and to convert
dev_change_net_namespace to a static inline wrapper.
Fixes: eeb85a14ee34 ("net: Allow to specify ifindex when device is moved to another namespace")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we can specify ifindex on link creation. This change allows
to specify ifindex when a device is moved to another network namespace.
Even now, a device ifindex can be changed if there is another device
with the same ifindex in the target namespace. So this change doesn't
introduce completely new behavior, it adds more control to the process.
CRIU users want to restore containers with pre-created network devices.
A user will provide network devices and instructions where they have to
be restored, then CRIU will restore network namespaces and move devices
into them. The problem is that devices have to be restored with the same
indexes that they have before C/R.
Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com>
Suggested-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If register_netdevice() fails after having called cfg80211's
netdev notifier (cfg80211_netdev_notifier_call) it will call
the notifier again with UNREGISTER. This would then lock the
wiphy mutex because we're marked as registered, which causes
a deadlock.
Fix this by separately keeping track of whether or not we're
in the middle of registering to also skip the notifier call
on this unregister.
Reported-by: syzbot+2ae0ca9d7737ad1a62b7@syzkaller.appspotmail.com
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver")
Link: https://lore.kernel.org/r/20210201192048.ed8bad436737.I7cae042c44b15f80919a285799a15df467e9d42d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is needed since it calls into the driver, which must have the
same context as if we got to destroy an interface through nl80211.
Fix this, and add a direct lockdep assertion so we don't see it
pop up only when the driver calls back to cfg80211.
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver")
Reported-by: syzbot+4305e814f9b267131776@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20210128183454.d31df9cbd7ce.I1beb07c9492f0ade900e864a098c57041e7a7ebf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We used to not require anything in terms of registering netdevs
with cfg80211, using a netdev notifier instead. However, in the
next patch reducing RTNL locking, this causes big problems, and
the simplest way is to just require drivers to do things better.
Change the registration/unregistration semantics to require the
drivers to call cfg80211_(un)register_netdevice() when this is
happening due to a cfg80211 request, i.e. add_virtual_intf() or
del_virtual_intf() (or if it somehow has to happen in any other
cfg80211 callback).
Otherwise, in other contexts, drivers may continue to use the
normal netdev (un)registration functions as usual.
Internally, we still use the netdev notifier and track (by the
new wdev->registered bool) if the wdev had already been added
to cfg80211 or not.
Link: https://lore.kernel.org/r/20210122161942.cf2f4b65e4e9.Ida8234e50da13eb675b557bac52a713ad4eddf71@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some updates:
* injection/radiotap updates for new test capabilities
* remove WDS support - even years ago when we turned
it off by default it was already basically unusable
* support for HE (802.11ax) rates for beacons
* support for some vendor-specific HE rates
* many other small features/cleanups
* tag 'mac80211-next-for-net-next-2020-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (21 commits)
nl80211: fix kernel-doc warning in the new SAE attribute
cfg80211: remove WDS code
mac80211: remove WDS-related code
rt2x00: remove WDS code
b43legacy: remove WDS code
b43: remove WDS code
carl9170: remove WDS code
ath9k: remove WDS code
wireless: remove CONFIG_WIRELESS_WDS
mac80211: assure that certain drivers adhere to DONT_REORDER flag
mac80211: don't overwrite QoS TID of injected frames
mac80211: adhere to Tx control flag that prevents frame reordering
mac80211: add radiotap flag to assure frames are not reordered
mac80211: save HE oper info in BSS config for mesh
cfg80211: add support to configure HE MCS for beacon rate
nl80211: fix beacon tx rate mask validation
nl80211/cfg80211: fix potential infinite loop
cfg80211: Add support to calculate and report 4096-QAM HE rates
cfg80211: Add support to configure SAE PWE value to drivers
ieee80211: Add definition for WFA DPP
...
====================
Link: https://lore.kernel.org/r/20201113101148.25268-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove all the code that was there to configure WDS interfaces,
now that there's no way to reach it anymore.
Link: https://lore.kernel.org/r/20201109105103.8f5b98e4068d.I5f5129041649ef2862b69683574bb3344743727b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's a race condition in the netdev registration in that
NETDEV_REGISTER actually happens after the netdev is available,
and so if we initialize things only there, we might get called
with an uninitialized wdev through nl80211 - not using a wdev
but using a netdev interface index.
I found this while looking into a syzbot report, but it doesn't
really seem to be related, and unfortunately there's no repro
for it (yet). I can't (yet) explain how it managed to get into
cfg80211_release_pmsr() from nl80211_netlink_notify() without
the wdev having been initialized, as the latter only iterates
the wdevs that are linked into the rdev, which even without the
change here happened after init.
However, looking at this, it seems fairly clear that the init
needs to be done earlier, otherwise we might even re-init on a
netns move, when data might still be pending.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20201009135821.fdcbba3aad65.Ie9201d91dbcb7da32318812effdc1561aeaf4cdc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Support 6 GHz scanning, by
* a new scan flag to scan for colocated BSSes advertised
by (and found) APs on 2.4 & 5 GHz
* doing the necessary reduced neighbor report parsing for
this, to find them
* adding the ability to split the scan request in case the
device by itself cannot support this.
Also add some necessary bits in mac80211 to not break with
these changes.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Gives drivers the definitions needed to advertise support
for S1G bands.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200602062247.23212-1-thomas@adapt-ip.com
Link: https://lore.kernel.org/r/20200731055636.795173-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Lockdep reports that we may deadlock because we take the RTNL on
the work struct, but flush it under RTNL. Clearly, it's correct.
In practice, this can happen when doing rfkill on an active device.
Fix this by moving the work struct to the wiphy (registered dev)
layer, and iterate over all the wdevs inside there. This then
means we need to track which one of them has work to do, so we
don't update to the driver for all wdevs all the time.
Also fix a locking bug I noticed while working on this - the
registrations list is iterated as if it was an RCU list, but it
isn't handle that way - and we need to lock now for the update
flag anyway, so remove the RCU.
Fixes: 6cd536fe62ef ("cfg80211: change internal management frame registration API")
Reported-by: Markus Theil <markus.theil@tu-ilmenau.de>
Reported-and-tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200604120420.b1dc540a7e26.I55dcca56bb5bdc5d7ad66a36a0b42afd7034d8be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 6 GHz band, HE capabilities must be available for all of
the interface types, otherwise we shouldn't use 6 GHz. Check
this.
Link: https://lore.kernel.org/r/20200528213443.5881cb3c8c4a.I583b54172f91f98d44af64a16c5826fe458cbb27@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On the 6 GHz band, HE should be used, but without any direct HT/VHT
capabilities, instead the HE 6 GHz band capabilities will capture
the relevant information. Reject HT/VHT capabilities here.
Link: https://lore.kernel.org/r/20200528213443.bfe89c35459a.Ibba5e066fa0087fd49d13cfee89d196ea0c68ae2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Removing the "if (IS_ERR(dir)) dir = NULL;" check only works
if we adjust the remaining code to not rely on it being NULL.
Check IS_ERR_OR_NULL() before attempting to dereference it.
I'm not actually entirely sure this fixes the syzbot crash as
the kernel config indicates that they do have DEBUG_FS in the
kernel, but this is what I found when looking there.
Cc: stable@vger.kernel.org
Fixes: d82574a8e5a4 ("cfg80211: no need to check return value of debugfs_create functions")
Reported-by: syzbot+fd5332e429401bf42d18@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200525113816.fc4da3ec3d4b.Ica63a110679819eaa9fb3bc1b7437d96b1fd187d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This should be covered by the next MHz, make sure that the
numbers are always normalized.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200424120103.12b91ecf75f9.I4bf499d58404283bbfacb517d614a816763bccf2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for requesting that the ranging measurement will use
the trigger-based / non trigger-based flow instead of the EDCA based
flow.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-2-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If wdev->wext.keys was initialized it didn't get reset to NULL on
unregister (and it doesn't get set in cfg80211_init_wdev either), but
wdev is reused if unregister was triggered through
cfg80211_switch_netns.
The next unregister (for whatever reason) will try to free
wdev->wext.keys again.
Signed-off-by: Stefan Bühler <source@stbuehler.de>
Link: https://lore.kernel.org/r/20191126100543.782023-1-stefan.buehler@tik.uni-stuttgart.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the RFKILL subsystem isn't available, then rfkill_blocked()
always returns false. In the case of hardware rfkill this will
be wrong though, as if the hardware reported being killed then
it cannot operate any longer.
Since we only ever call the rfkill_sync work in this case, just
rename it to rfkill_block and always pass "true" for the blocked
parameter, rather than passing rfkill_blocked().
We rely on the underlying driver to still reject any new attempt
to bring up the device by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-2-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Just minor overlapping changes in the conflicts here.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 33d915d9e8ce ("{nl,mac}80211: allow 4addr AP operation on
crypto controlled devices") has introduced a change which allows
4addr operation on crypto controlled devices (ex: ath10k). This
change has inadvertently impacted the interface combinations logic
on such devices.
General rule is that software interfaces like AP/VLAN should not be
listed under supported interface combinations and should not be
considered during validation of these combinations; because of the
aforementioned change, AP/VLAN interfaces(if present) will be checked
against interfaces supported by the device and blocks valid interface
combinations.
Consider a case where an AP and AP/VLAN are up and running; when a
second AP device is brought up on the same physical device, this AP
will be checked against the AP/VLAN interface (which will not be
part of supported interface combinations of the device) and blocks
second AP to come up.
Add a new API cfg80211_iftype_allowed() to fix the problem, this
API works for all devices with/without SW crypto control.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Fixes: 33d915d9e8ce ("{nl,mac}80211: allow 4addr AP operation on crypto controlled devices")
Link: https://lore.kernel.org/r/1563779690-9716-1-git-send-email-mpubbise@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190703070142.GA29993@kroah.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Honestly all the conflicts were simple overlapping changes,
nothing really interesting to report.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes, all over:
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In wiphy_new_nm(), if an error occurs after dev_set_name() and
device_initialize() have already been called, it's necessary to call
put_device() (via wiphy_free()) to avoid a memory leak.
Reported-by: syzbot+7fddca22578bc67c3fe4@syzkaller.appspotmail.com
Fixes: 1f87f7d3a3b4 ("cfg80211: add rfkill support")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Require that each vendor command give a policy of its sub-attributes
in NL80211_ATTR_VENDOR_DATA, and then (stricly) check the contents,
including the NLA_F_NESTED flag that we couldn't check on the outer
layer because there we don't know yet.
It is possible to use VENDOR_CMD_RAW_DATA for raw data, but then no
nested data can be given (NLA_F_NESTED flag must be clear) and the
data is just passed as is to the command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As per the current design, in the case of sw crypto controlled devices,
it is the device which advertises the support for AP/VLAN iftype based
on it's ability to tranmsit packets encrypted in software
(In VLAN functionality, group traffic generated for a specific
VLAN group is always encrypted in software). Commit db3bdcb9c3ff
("mac80211: allow AP_VLAN operation on crypto controlled devices")
has introduced this change.
Since 4addr AP operation also uses AP/VLAN iftype, this conditional
way of advertising AP/VLAN support has broken 4addr AP mode operation on
crypto controlled devices which do not support VLAN functionality.
In the case of ath10k driver, not all firmwares have support for VLAN
functionality but all can support 4addr AP operation. Because AP/VLAN
support is not advertised for these devices, 4addr AP operations are
also blocked.
Fix this by allowing 4addr operation on devices which do not support
AP/VLAN iftype but can support 4addr AP operation (decision is based on
the wiphy flag WIPHY_FLAG_4ADDR_AP).
Cc: stable@vger.kernel.org
Fixes: db3bdcb9c3ff ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When we destroy the interface we already hold the wdev->mtx
while calling cfg80211_pmsr_wdev_down(), which assumes this
isn't true and flushes the worker that takes the lock, thus
leading to a deadlock.
Fix this by refactoring the worker and calling its code in
cfg80211_pmsr_wdev_down() directly.
We still need to flush the work later to make sure it's not
still running and will crash, but it will not do anything.
Fixes: 9bb7e0f24e7e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When a wiphy changes its namespace, all interfaces are moved to the
new namespace as well. The network interfaces are properly announced
as leaving on the old and as appearing on the new namespace through
RTM_NEWLINK/RTM_DELLINK. On nl80211, however, these events are missing
for radios and their interfaces.
Add netlink announcements through nl80211 when switching namespaces,
so userspace can rely on these events to discover radios properly.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a new "peer measurement" API, that can be used to measure
certain things related to a peer. Right now, only implement
FTM (flight time measurement) over it, but the idea is that
it'll be extensible to also support measuring the necessary
things to calculate e.g. angle-of-arrival for WiGig.
The API is structured to have a generic list of peers and
channels to measure with/on, and then for each of those a
set of measurements (again, only FTM right now) to perform.
Results are sent to the requesting socket, including a final
complete message.
Closing the controlling netlink socket will abort a running
measurement.
v3:
- add a bit to report "final" for partial results
- remove list keeping etc. and just unicast out the results
to the requester (big code reduction ...)
- also send complete message unicast, and as a result
remove the multicast group
- separate out struct cfg80211_pmsr_ftm_request_peer
from struct cfg80211_pmsr_request_peer
- document timeout == 0 if no timeout
- disallow setting timeout nl80211 attribute to 0,
must not include attribute for no timeout
- make MAC address randomization optional
- change num bursts exponent default to 0 (1 burst, rather
rather than the old default of 15==don't care)
v4:
- clarify NL80211_ATTR_TIMEOUT documentation
v5:
- remove unnecessary nl80211 multicast/family changes
- remove partial results bit/flag, final is sufficient
- add max_bursts_exponent, max_ftms_per_burst to capability
- rename "frames per burst" -> "FTMs per burst"
v6:
- rename cfg80211_pmsr_free_wdev() to cfg80211_pmsr_wdev_down()
and call it in leave, so the device can't go down with any
pending measurements
v7:
- wording fixes (Lior)
- fix ftm.max_bursts_exponent to allow having the limit of 0 (Lior)
v8:
- copyright statements
- minor coding style fixes
- fix error path leak
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There isn't really any need for us to be sending this from
two different places - move cfg80211_init_wdev() later and
send the notification from there, removing it from the non-
netdev case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|