| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We have adjacent changes for the cs42l43 DT schema, merge the fixes
branch up so that there's a single thing for people to base future
changes on.
|
|
The ASP1 DOUT line must be defaulted to be high-impedance when
it is not actually transmitting data for an active channel.
In non-SoundWire modes ASP1 will usually be shared by multiple
amps so each amp must only drive the line during the slot for
an enabled TX channel.
In SoundWire mode a custom firmware can use ASP1 as a secondary
chip-to-chip audio link or as GPIO. It should be defaulted to
high-impedance since by default the purpose of this pin is not
known.
Backport note:
On kernel versions before 6.6 the cs35l56->base.regmap argument
to regmap_set_bits() must be changed to cs35l56->regmap.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://lore.kernel.org/r/20231009153412.30380-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix cs35l56_patch() to call reinit_completion() to reinitialize
the completion object.
It was incorrectly using init_completion().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://lore.kernel.org/r/20231006164405.253796-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The cs35l56_pm_ops_i2c_spi struct is only needed if either the
I2C or SPI modules are selected for building. Otherwise it would
be unused bytes, so in that case omit it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230914150918.14505-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
pm.h now has macros to create and export the dev_pm_ops struct
only if CONFIG_PM is enabled.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230914150918.14505-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
The PCI device registers contain a subsystem ID (SSID), that is
separate from the silicon ID. The PCI specification defines it thus:
"They provide a mechanism for board vendors to distiguish their
boards from one another even thought the boards may have the same
PCI controller on them."
This allows the driver for the silicon part to apply board-speficic
settings based on this SSID.
The CS35L56 driver uses this to select the correct firmware file for
the board. The actual ID is part of the PCI register set of the
host audio interface so this set of patches includes extracting the
SSID from the Intel audio controller and passing it to the machine
driver and then to ASoC components. Other PCI audio controllers
will have the same SSID registers, so can use the same mechanism to
pass the SSID.
|
|
If the driver properties do not define a cirrus,firmware-uid try to get the
PCI SSID as the UID.
On PCI-based systems the PCI SSID is used to uniquely identify the specific
sound hardware. This is the standard mechanism for x86 systems and is the
way to get a unique system identifier for systems that use the CS35L56 on
SoundWire.
For non-SoundWire systems there is no Windows equivalent of the ASoC driver
in I2C/SPI mode. These would be:
1. HDA systems, which are handled by the HDA subsystem.
2. Linux-specific systems.
3. Composite devices where the cs35l56 is not present in ACPI and is
configured using software nodes.
Case 2 can use the firmware-uid property, though the PCI SSID is supported
as an alternative, as it is the standard PCI mechanism.
Case 3 is a SoundWire system where some other codec is the SoundWire bridge
device and CS35L56 is not listed in ACPI. As these are SoundWire systems
they will normally use the PCI SSID.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230912163207.3498161-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Driver remove() must call pm_runtime_dont_use_autosuspend().
Drivers that call pm_runtime_use_autosuspend() must disable
it in driver remove(). Unfortunately until recently this was
only mentioned in 1 line in a 900+ line document so most
people hadn't noticed this. It has only recently been added
to the kerneldoc of pm_runtime_use_autosuspend().
THIS WON'T APPLY CLEANLY TO V6.5 AND EARLIER:
We will send a separate backported patch to stable.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230908101716.2658582-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For the benefit of CI.
|
|
Use a device property "cirrus,firmware-uid" to get the unique firmware
identifier instead of using ACPI _SUB. There aren't any products that use
_SUB.
There will not usually be a _SUB in Soundwire nodes. The ACPI can use a
_DSD section for custom properties.
There is also a need to support instantiating this driver using software
nodes. This is for systems where the CS35L56 is a back-end device and the
ACPI refers only to the front-end audio device - there will not be any ACPI
references to CS35L56.
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230817112712.16637-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Only attempt to download wmfw/bin files to a non-secured part if
it reports FIRMWARE_MISSING. If FIRMWARE_MISSING is false the
firmware has already been patched and overwriting the patch could
corrupt the running firmware.
For a secured part the wmfw/bin can be downloaded even if
FIRMWARE_MISSING is false, because they will only patch tunings.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230815124826.5447-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a flag to wm_adsp_power_up() that indicates whether it should attempt
to find and load firmware files.
This is to support DSPs that have built-in firmware that may already have
been patched (for example, by the BIOS). In that case the patch must not
be overwritten because that could corrupt the running firmware.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230815124826.5447-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When cs35l56_system_resume() needs to reload firmware it should call
wm_adsp_power_down() to put cs_dsp into a powered-down state before
cs35l56_secure_patch() or cs35l56_patch() calls wm_adsp_power_up().
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230808164702.21272-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The CS35L56 could be hard-reset during a system suspend-resume cycle,
either by the codec driver, in cs35l56_system_resume_early(), or by ACPI.
After a hard reset the driver must wait for the control port to be ready
(datasheet tIRS time) before attempting to access the CS35L56.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230808164702.21272-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ACPI setting for a GPIO default state has higher priority than the
flag passed to devm_gpiod_get_optional() so ACPI can override the
GPIOD_OUT_LOW. Explicitly set the GPIO low when hard resetting.
Although GPIOD_OUT_LOW can't be relied on this doesn't seem like a
reason to stop passing it to devm_gpiod_get_optional(). So we still pass
it to state our intent, but can deal with it having no effect.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230808164702.21272-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Re-implement setting of ASP TDM slots so that only the common loop to
build the register word is factored out.
The original cs35l56_set_asp_slot_positions() had an apparent
uninitialized variable if the passed register address was neither of the
ASP slot registers. In fact this would never happen because the calling
code passed valid registers.
While it's trivial to initialize the variable or add a default case,
actually the only common code was the loop at the end of the function,
which simply manipulates some mask values and is identical for either
register. Factoring out the regmap_write() didn't really gain anything.
So instead re-implement the code to replace the original function with
cs35l56_make_tdm_config_word() that only does the loop, and change the
calling code to call regmap_write() directly.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230808164702.21272-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move issuing of a CS35L56_MBOX_CMD_SHUTDOWN command and then waiting for
the DSP to reach CS35L56_HALO_STATE_SHUTDOWN in the register appropriate
for the hardware revision into a common function.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-10-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Part of the initialization code in cs35l56_init() can be re-used
by the HDA driver so move it into a new function in the shared
library.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-8-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the code that initialized the struct cs_dsp members
into the shared library so that the HDA driver can use it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-7-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The majority of runtime_suspend and runtime_resume handling
doesn't have anything specific to the ASoC driver, so can be
shared by the HDA driver. Move this code into the shared
library.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Move the cs35l56 utility functions into the shared file so they are
available for use in HDA.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the new cs35l56_base struct for utility functions.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function can be more easily reused in HDA if the tracking of whether
a soft reset is being performed and whether the device is connected to a
SoundWire bus is moved out of the function.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ASoC and HDA drivers have structures that contain some of the same
information - instead of maintaining two locations for this data the
drivers should share a common data structure as this will enable common
utility functions to be created.
The first step is to move the location of these members in the ASoC
driver.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230721132120.5523-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The soft (firmware) registers for volume/mute/posture are not reset by
a chip soft-reset, so use a regmap patch to set them to defaults.
cs35l56_reread_firmware_registers() has been removed. Its intent was to
use whatever the firmware set as a default. But the driver now patches the
defaults to the registers.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230718144625.39634-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
So we can apply the tlv320aic3xxx DT conversion.
|
|
The dma pointer must be set to the passed stream pointer, even
if that pointer is NULL.
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230601124907.3128170-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Cristian Ciocaltea <cristian.ciocaltea@collabora.com>:
This patch series handles a few issues related to the ES8316 audio
codec, discovered while doing some testing on the Rock 5B board.
|
|
If the device is in secure mode it's unnecessary to send a SHUTDOWN and
SYSTEM_RESET around the firmware download. It could only be patching
insecure tunings. A tuning patch doesn't need a SHUTDOWN and only needs
a REINIT afterwards. This will reduce the overhead of exiting system
suspend in secure mode.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/Message-Id: <20230518150250.1121006-4-rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SoundWire bus accesses must be performed under the guard of a pm_runtime
request, in this case the write was being performed just after the
request had been put() and so the bus could not be guaranteed to be
available.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/Message-Id: <20230518150250.1121006-3-rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Each time we go through dsp_work() it does a devm_kasprintf() to
allocate memory to hold the part name string. It's not strictly a memory
leak because devm will free it all if the driver is removed. But we keep
allocating more and more memory to hold the same string.
Move the allocation so that it is performed after the version and
secured state information is gathered and handle allocation errors.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/Message-Id: <20230518150250.1121006-2-rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Flush the SoundWire interrupt handler work instead of cancelling it.
When a SoundWire interrupt is triggered the pm_runtime is held
until the work has completed. It's therefore unsafe to cancel
the work, it must be flushed.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com
Link: https://lore.kernel.org/r/20230512144237.739000-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org
|
|
cs35l56_mbox_send() logs a warning when sending a mbox command fails so
the callers can be simplified.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230420102043.1151830-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Reduce SDW1 to 4 channels and remove the controls for SDW1
TX5 and TX6.
The TX5 and TX6 channels have been removed from B0 silicon.
There is no need to support them on A1 silicon.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230418144309.1100721-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
EINT20 contains wake-source interrupts and also interface-blocked
interrupts, which all default to unmasked after reset or wake.
The comment in cs35l56_init() only mentioned the wake interrupts.
Update the comment so it's clear that it's intentional to also
mask the *_BLOCKED interrupts.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230418144309.1100721-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
cs35l56_remove() always returns 0. Two of the functions that call
it are void and the other one should only return 0. So there's no
point returning anything from cs35l56_remove().
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230414133753.653139-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dsp_ready_completion is redundant and can be replaced by a call
flush_work() to wait for cs35l56_dsp_work() to complete.
As the dsp_work is queued by component_probe() it must run before other
ASoC component callbacks and therefore there is no risk of calling
flush_work() before the dsp_work() has been queued.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230414133753.653139-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Moving the wait from the beginning of the cs35l56_dsp_work() into
cs35l56_component_probe() will prevent the limbo situation that is an
artifact of the two stage SoundWire driver probe and initialisation
where the card is all registered and shows in ALSA but doesn't actually
work because the hardware didn't enumerate.
The other bus drivers perform the probe and init sequentially and are
not susceptible to this issue.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230414133753.653139-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no reason to have such a tight usleep range of 400us and it is
acceptable to allow MIN_US * 2.
Also wrap the usleep in an inline function.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/168147949455.26.3401634900657387799@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The irq member was being set before calling the init function and then
cs35l56_irq_request() was called only when the init was successful.
However cs35l56_release() calls devm_free_irq() when the irq member is
set and therefore if init() fails then this will cause an attempted free
of an unallocated IRQ.
Instead pass the desired IRQ number to the cs35l56_irq_request()
function and set cs35l56->irq only when it has been successfully
allocated.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/168147949598.26.711670799488943454@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Check during cs35l56_system_resume() whether the firmware patch must
be applied again.
The FIRMWARE_MISSING flag in the PROTECTION_STATUS register indicates
whether the firmware has been patched.
In non-secure mode the FIRMWARE_MISSING flag is cleared at the end of
dsp_work(). If it is set after system-resume we know that dsp_work()
must be run again.
In secure mode the pre-OS loader will have done the secure patching
and cleared the FIRMWARE_MISSING flag. So this flag does not tell us
whether firmware memory was lost. But the driver could only be
downloading non-secure tunings, which is always safe to do.
If the driver has control of RESET we will have asserted it during
suspend so the firmware patch will have been lost. The driver would only
have control of RESET in non-secure mode.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/168122674550.26.8545058503709956172@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Delete the 'removing' flag and don't kick init_completion to make a
quick cancel of dsp_work(). Just let it timeout on the wait for the
completion.
Simplify the code to standard cancelling or flushing of the work.
This avoids introducing corner cases from a layer of custom signalling.
It also avoids potential race conditions when system-suspend handling
is added.
Unless the hardware is broken, the dsp_work() will already have started
and passed the completion before the driver would want to cancel it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/168122674746.26.16881587647873355224@mailman-core.alsa-project.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds the main handling for system suspend but does not handle
re-patching the firmware after system resume.
This is a multi-stage suspend and resume because if there is a
RESET line it is almost certain that it will be shared by all the
amps. So every amp must have done its suspend before we can
assert RESET. Likewise we must de-assert RESET before the amps
can resume.
It's preferable to assert RESET before we turning off regulators, and
while they power up.
The actual suspend and resume is done by using the pair
pm_runtime_force_suspend() and pm_runtime_force_resume() to
re-use our runtime suspend/resume sequences.
pm_runtime_force_suspend() will disable our pm_runtime. If we were
runtime-resumed it calls our runtime_suspend().
pm_runtime_force_resume() re-enables pm_runtime and if we were
originally runtime-resumed before the pm_runtime_force_suspend()
it calls our runtime_resume(). Otherwise it leaves us
runtime-suspended.
The general process is therefore:
suspend() -> finish dsp_work and then run our runtime_suspend
suspend_late() -> assert RESET and turn off supplies
resume_early() -> enable supplies and de-assert RESET
resume() -> pm_runtime_force_resume()
In addition, to prevent the IRQ handler running in the period
between pm_runtime_force_suspend() and pm_runtime_force_resume()
the parent IRQ is temporarily disabled:
- from suspend until suspend_noirq
- from resume_noirq until resume
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230411152528.329803-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When we are resuming from a system suspend the CS35L56 has probably
been hard reset (usually a power-on reset). So we must wait for the
firmware to boot. On SoundWire we also need it to re-initialize before
we can read the registers to check the CS35L56 state.
The simplest way to handle this is for runtime-resume to always wait
for firmware boot. If the firmware is already booted the overhead is
only one register read.
The system-resume will have to runtime-resume the driver anyway before
attempting any register access. So this will automatically include the
wait for initialization on SoundWire.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230411152528.329803-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
At the start of dsp_work() only wait for init_completion if !init_done.
This allows system suspend to re-queue dsp_work() without having to
do a dummy complete() of init_completion.
A dummy completion in system suspend would have to be conditional on
init_done. But that would create a possible race condition between our
system resume and cs35l56_init() in the corner case that we suspend right
after the SoundWire core has enumerated and reported ATTACHED.
It is safer and simpler to have cs35l56_init() as the only place that
init_completion is completed, and dsp_work() as the only place that
it is consumed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230411152528.329803-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If we use a DAPM widget instead of mute_stream() to send the
PLAY command we can issue the plays to multiple amps in parallel.
With mute_stream each codec driver instance is called one at a
time so we get N * PS0 delay time.
DAPM does each stage on every widget in a card before moving to
the next stage. So all amps will do the PRE_PMU then all will do
the POST_PMU. The PLAY is sent in the PRE_PMU so that they all
power-up in parallel. After the PS0 wait in the first POST_PMU
all the other amps will also be ready so there won't be any extra
delay, or it will be negligible.
There's also no point waiting for the MBOX ack in the PRE_PMU.
We won't see a PS0 state in POST_PMU if it didn't ack the PLAY
command. So we can save a little extra time.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230411152528.329803-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The variable 'rv' is defined as unsigned type, so the following if
statement is invalid, we can modify the type of rv to int.
if (rv < 0) {
dev_err(cs35l56->dev, "irq: failed to get pm_runtime:
%d\n", rv);
goto err_unlock;
}
./sound/soc/codecs/cs35l56.c:333:5-7: WARNING: Unsigned expression compared with zero: rv < 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4599
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230324022303.121485-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The CS35L56 combines a high-performance mono audio amplifier, Class-H
tracking inductive boost converter, Halo Core(TM) DSP and a DC-DC boost
converter supporting Class-H tracking.
Supported control interfaces are I2C, SPI or SoundWire.
Supported audio interfaces are I2S/TDM or SoundWire.
Most chip functionality is controlled by on-board ROM firmware that is
always running. The driver must apply patch/tune to the firmware
before using the CS35L56.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230320112245.115720-9-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
