summaryrefslogtreecommitdiff
path: root/sound/soc/codecs/sgtl5000.c
AgeCommit message (Collapse)AuthorFilesLines
2023-05-08ASoC: Switch i2c drivers back to use .probe()Uwe Kleine-König1-1/+1
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new() call-back type"), all drivers being converted to .probe_new() and then 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert back to (the new) .probe() to be able to eventually drop .probe_new() from struct i2c_driver. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de Link: https://lore.kernel.org/r/20230425095716.331419-1-u.kleine-koenig@pengutronix.de Signed-off-by: Mark Brown <broonie@kernel.org
2022-11-10ASoC: sgtl5000: Reset the CHIP_CLK_CTRL reg on removeDetlev Casanova1-0/+1
Since commit bf2aebccddef ("ASoC: sgtl5000: Fix noise on shutdown/remove"), the device power control registers are reset when the driver is removed/shutdown. This is an issue when the device is configured to use the PLL clock. The device will stop responding if it is still configured to use the PLL clock but the PLL clock is powered down. When rebooting linux, the probe function will show: sgtl5000 0-000a: Error reading chip id -11 Make sure that the CHIP_CLK_CTRL is reset to its default value before powering down the device. Fixes: bf2aebccddef ("ASoC: sgtl5000: Fix noise on shutdown/remove") Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20221110190612.1341469-1-detlev.casanova@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-08-16i2c: Make remove callback return voidUwe Kleine-König1-3/+1
The value returned by an i2c driver's remove function is mostly ignored. (Only an error message is printed if the value is non-zero that the error is ignored.) So change the prototype of the remove function to return no value. This way driver authors are not tempted to assume that passing an error to the upper layer is a good idea. All drivers are adapted accordingly. There is no intended change of behaviour, all callbacks were prepared to return 0 before. Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com> Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au> Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Crt Mori <cmo@melexis.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013 Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/* Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5 Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860 Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power Acked-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@kernel.org>
2022-06-29ASoC: Refactor non_legacy_dai_naming flagMark Brown1-1/+0
Merge series from Charles Keepax <ckeepax@opensource.cirrus.com>: Historically, the legacy DAI naming scheme was applied to platform drivers and the newer scheme to CODEC drivers. During componentisation the core lost the knowledge of if a driver was a CODEC or platform, they were all now components. To continue to support the legacy naming on older platform drivers a flag was added to the snd_soc_component_driver structure, non_legacy_dai_naming, to indicate to use the new scheme and this was applied to all CODECs as part of the migration. However, a slight issue appears to be developing with respect to this flag being opt in for the non-legacy scheme, which presumably we want to be the primary scheme used. Many codec drivers appear to forget to include this flag: grep -l -r "snd_soc_component_driver" sound/soc/codecs/*.c | xargs grep -L "non_legacy_dai_naming" | wc 48 48 556 Whilst in many cases the configuration of the DAIs themselves will cause the core to apply the new scheme anyway, it would seem more sensible to change the flag to legacy_dai_naming making the new scheme opt out. This patch series migrates across to such a scheme.
2022-06-27ASoC: sgtl5000: Remove now redundant non_legacy_dai_naming flagCharles Keepax1-1/+0
The ASoC core has now been changed to default to the non-legacy DAI naming, as such drivers using the new scheme no longer need to specify the non_legacy_dai_naming flag. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20220623125250.2355471-90-ckeepax@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-06-24ASoC: sgtl5000: Fix noise on shutdown/removeFrancesco Dolcini1-0/+9
Put the SGTL5000 in a silent/safe state on shutdown/remove, this is required since the SGTL5000 produces a constant noise on its output after it is configured and its clock is removed. Without this change this is happening every time the module is unbound/removed or from reboot till the clock is enabled again. The issue was experienced on both a Toradex Colibri/Apalis iMX6, but can be easily reproduced everywhere just playing something on the codec and after that removing/unbinding the driver. Fixes: 9b34e6cc3bc2 ("ASoC: Add Freescale SGTL5000 codec support") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Fabio Estevam <festevam@denx.de> Link: https://lore.kernel.org/r/20220624101301.441314-1-francesco.dolcini@toradex.com Signed-off-by: Mark Brown <broonie@kernel.org>
2022-04-07ASoC: sgtl5000: use simple i2c probe functionStephen Kitt1-3/+2
The i2c probe functions here don't use the id information provided in their second argument, so the single-parameter i2c probe function ("probe_new") can be used instead. This avoids scanning the identifier tables during probes. Signed-off-by: Stephen Kitt <steve@sk2.org> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20220405164031.2160888-1-steve@sk2.org Signed-off-by: Mark Brown <broonie@kernel.org>
2021-12-20ASoC: codecs: sgtl5000: Use dev_err_probe() helperKuninori Morimoto1-3/+2
Use the dev_err_probe() helper, instead of open-coding the same operation. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20211214020843.2225831-7-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-03-10ASoC: sgtl5000: Fix identation of .driver elementsFabio Estevam1-3/+3
The .driver elements are not correctly idented. Fix the identation of the .driver elements. Signed-off-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20210302142817.2141923-1-festevam@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org>
2021-03-10ASoC: sgtl5000: set DAP_AVC_CTRL register to correct default value on probeBenjamin Rood1-1/+1
According to the SGTL5000 datasheet [1], the DAP_AVC_CTRL register has the following bit field definitions: | BITS | FIELD | RW | RESET | DEFINITION | | 15 | RSVD | RO | 0x0 | Reserved | | 14 | RSVD | RW | 0x1 | Reserved | | 13:12 | MAX_GAIN | RW | 0x1 | Max Gain of AVC in expander mode | | 11:10 | RSVD | RO | 0x0 | Reserved | | 9:8 | LBI_RESP | RW | 0x1 | Integrator Response | | 7:6 | RSVD | RO | 0x0 | Reserved | | 5 | HARD_LMT_EN | RW | 0x0 | Enable hard limiter mode | | 4:1 | RSVD | RO | 0x0 | Reserved | | 0 | EN | RW | 0x0 | Enable/Disable AVC | The original default value written to the DAP_AVC_CTRL register during sgtl5000_i2c_probe() was 0x0510. This would incorrectly write values to bits 4 and 10, which are defined as RESERVED. It would also not set bits 12 and 14 to their correct RESET values of 0x1, and instead set them to 0x0. While the DAP_AVC module is effectively disabled because the EN bit is 0, this default value is still writing invalid values to registers that are marked as read-only and RESERVED as well as not setting bits 12 and 14 to their correct default values as defined by the datasheet. The correct value that should be written to the DAP_AVC_CTRL register is 0x5100, which configures the register bits to the default values defined by the datasheet, and prevents any writes to bits defined as 'read-only'. Generally speaking, it is best practice to NOT attempt to write values to registers/bits defined as RESERVED, as it generally produces unwanted/undefined behavior, or errors. Also, all credit for this patch should go to my colleague Dan MacDonald <dmacdonald@curbellmedical.com> for finding this error in the first place. [1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf Signed-off-by: Benjamin Rood <benjaminjrood@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20210219183308.GA2117@ubuntu-dev Signed-off-by: Mark Brown <broonie@kernel.org>
2021-01-21ASoC: sgtl5000: sync parameter naming (rate/sample_bits)Kuninori Morimoto1-1/+1
This patch syncs naming rule. - xxx_rates; + xxx_rate; - xxx_samplebits; + xxx_sample_bits; Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/87pn26n6u4.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-07-17ASoC: codecs: merge .digital_mute() into .mute_stream()Kuninori Morimoto1-2/+3
snd_soc_dai_digital_mute() is internally using both mute_stream() (1) or digital_mute() (2), but the difference between these 2 are only handling direction. We can merge digital_mute() into mute_stream int snd_soc_dai_digital_mute(xxx, int direction) { ... else if (dai->driver->ops->mute_stream) (1) return dai->driver->ops->mute_stream(xxx, direction); else if (direction == SNDRV_PCM_STREAM_PLAYBACK && dai->driver->ops->digital_mute) (2) return dai->driver->ops->digital_mute(xxx); ... } Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/875zaxxxi4.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-06-22ASoC: codecs: rename to snd_soc_component_read()Kuninori Morimoto1-8/+8
We need to use snd_soc_component_read() instead of snd_soc_component_read32() This patch renames _read32() to _read() Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/87mu534me5.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-04-15ASoC: sgtl5000: Fix VAG power-on handlingSebastian Reichel1-0/+34
As mentioned slightly out of patch context in the code, there is no reset routine for the chip. On boards where the chip is supplied by a fixed regulator, it might not even be resetted during (e.g. watchdog) reboot and can be in any state. If the device is probed with VAG enabled, the driver's probe routine will generate a loud pop sound when ANA_POWER is being programmed. Avoid this by properly disabling just the VAG bit and waiting the required power down time. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Reviewed-by: Fabio Estevam <festivem@gmail.com> Link: https://lore.kernel.org/r/20200414181140.145825-1-sebastian.reichel@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org>
2020-01-14ASoC: sgtl5000: add multi endpoint supportMarek Vasut1-0/+8
Support multiple endpoints on SGTL5000 codec port when used in of_graph context. This patch allows to share the codec port between two CPU DAIs. Example: Custom STM32MP157C board uses SGTL5000 audio codec. This codec is connected to two serial audio interfaces, which are configured either as rx or tx. From AsoC point of view the topolgy is the following: // 2 CPU DAIs (SAI2A/B), 1 Codec (SGTL5000) Playback: CPU-A-DAI(slave) -> (master)CODEC-DAI/port0 Record: CPU-B-DAI(slave) <- (master)CODEC-DAI/port0 In the DT two endpoints have to be associated to the codec port: sgtl5000_port: port { sgtl5000_tx_endpoint: endpoint@0 { remote-endpoint = <&sai2a_endpoint>; }; sgtl5000_rx_endpoint: endpoint@1 { remote-endpoint = <&sai2b_endpoint>; }; }; However, when the audio graph card parses the codec nodes, it expects to find DAI interface indexes matching the endpoints indexes. The current patch forces the use of DAI id 0 for both endpoints, which allows to share the codec DAI between the two CPU DAIs for playback and capture streams respectively. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20191219213219.366073-1-marex@denx.de Signed-off-by: Mark Brown <broonie@kernel.org>
2020-01-14ASoC: sgtl5000: Fix VDDA and VDDIO comparisonMarek Vasut1-1/+2
Comparing the voltage of VDDA and VDDIO to determine whether or not to enable VDDC manual override is insufficient. This is a problem in case the VDDA is supplied from different regulator than VDDIO, while both report the same voltage to the regulator framework. In that case where VDDA and VDDIO is supplied by different regulators, the VDDC manual override must not be applied. Fixes: b6319b061ba2 ("ASoC: sgtl5000: Fix charge pump source assignment") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Mark Brown <broonie@kernel.org> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Link: https://lore.kernel.org/r/20191220164450.1395038-2-marex@denx.de Signed-off-by: Mark Brown <broonie@kernel.org>
2019-07-22ASoC: sgtl5000: Fix charge pump source assignmentOleksandr Suvorov1-5/+10
If VDDA != VDDIO and any of them is greater than 3.1V, charge pump source can be assigned automatically [1]. [1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20190719100524.23300-7-oleksandr.suvorov@toradex.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-07-22ASoC: sgtl5000: Fix of unmute outputs on probeOleksandr Suvorov1-3/+3
To enable "zero cross detect" for ADC/HP, change HP_ZCD_EN/ADC_ZCD_EN bits only instead of writing the whole CHIP_ANA_CTRL register. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20190719100524.23300-6-oleksandr.suvorov@toradex.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-07-22ASoC: sgtl5000: add ADC mute controlOleksandr Suvorov1-0/+1
This control mute/unmute the ADC input of SGTL5000 using its CHIP_ANA_CTRL register. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20190719100524.23300-5-oleksandr.suvorov@toradex.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-07-22ASoC: sgtl5000: Fix definition of VAG Ramp ControlOleksandr Suvorov1-1/+1
SGTL5000_SMALL_POP is a bit mask, not a value. Usage of correct definition makes device probing code more clear. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20190719100524.23300-4-oleksandr.suvorov@toradex.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-07-22ASoC: sgtl5000: Improve VAG power and mute controlOleksandr Suvorov1-30/+194
VAG power control is improved to fit the manual [1]. This patch fixes as minimum one bug: if customer muxes Headphone to Line-In right after boot, the VAG power remains off that leads to poor sound quality from line-in. I.e. after boot: - Connect sound source to Line-In jack; - Connect headphone to HP jack; - Run following commands: $ amixer set 'Headphone' 80% $ amixer set 'Headphone Mux' LINE_IN Change VAG power on/off control according to the following algorithm: - turn VAG power ON on the 1st incoming event. - keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In). - turn VAG power OFF when there is the latest consumer's pre-down event come. - always delay after VAG power OFF to avoid pop. - delay after VAG power ON if the initiative consumer is Line-In, this prevents pop during line-in muxing. According to the data sheet [1], to avoid any pops/clicks, the outputs should be muted during input/output routing changes. [1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdf Cc: stable@vger.kernel.org Fixes: 9b34e6cc3bc2 ("ASoC: Add Freescale SGTL5000 codec support") Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com> Link: https://lore.kernel.org/r/20190719100524.23300-3-oleksandr.suvorov@toradex.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-01-07ASoC: sgtl5000: Allow SCLK pad drive strength to be changedAlison Wang1-1/+18
This patch introduces "sclk-strength" property to allow SCLK pad drive strength to be changed via device tree. When running playback test on LS1028ARDB, Tx Frame sync error interrupt will occur sometimes. Some noises also exist. After changing SCLK pad drive strength to the maximum value, the issues are gone. Signed-off-by: Alison Wang <alison.wang@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-09-06ASoC: sgtl5000: avoid division by zero if lo_vag is zeroColin Ian King1-1/+1
In the case where lo_vag <= SGTL5000_LINE_OUT_GND_BASE, lo_vag is set to zero and later vol_quot is computed by dividing by lo_vag causing a division by zero error. Fix this by avoiding a zero division and set vol_quot to zero in this specific case so that the lowest setting for i is correctly set. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-23ASoC: sgtl5000: Switch to SPDX identifierFabio Estevam1-9/+5
Adopt the SPDX license identifier headers to ease license compliance management. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-04-23ASoC: sgtl5000: Fix the spelling of 'exceed'Fabio Estevam1-2/+2
Fix the spelling of 'exceed' in two comments. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-02-19ASoC: sgtl5000: add 5 band graphic equalizerMichal Oleszczyk1-3/+21
Enable 5-band graphic equalizer which allows manipulation of gain in range -11.75dB to 12dB for 5 specific sound bands: 115Hz, 330Hz, 990Hz, 3000Hz, 9900Hz. Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-02-19ASoC: sgtl5000: add 'Audio Switch' block implementationMichal Oleszczyk1-11/+67
Add mux for choosing DAC source: ADC, I2S or DAP. DAP - digital audio processing block. Moreover create choosing mux for DAP main source (ADC or I2S) and DAP mixer source (ADC or I2S). Mixer block allows summing DAP main and mixer sources togheter with defined volumes. Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-02-16Merge branch 'fix/sgtl5000' of ↵Mark Brown1-0/+11
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-sgtl5000
2018-02-16ASoC: sgtl5000: Fix suspend/resumeFabio Estevam1-0/+11
Commit 8419caa72702 ("ASoC: sgtl5000: Do not disable regulators in SND_SOC_BIAS_OFF") causes the sgtl5000 to fail after a suspend/resume sequence: Playing WAVE '/media/a2002011001-e02.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo aplay: pcm_write:2051: write error: Input/output error The problem is caused by the fact that the aforementioned commit dropped the cache handling, so re-introduce the register map resync to fix the problem. Suggested-by: Mark Brown <broonie@kernel.org> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: <stable@vger.kernel.org>
2018-02-14Merge branch 'fix/sgtl5000' of ↵Mark Brown1-3/+12
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-sgtl5000
2018-02-14sgtl5000: change digital_mute policyMichal Oleszczyk1-3/+12
Current implementation mute codec in global way (DAC block). That means when user routes sound not from I2S but from AUX source (LINE_IN) it also will be muted by alsa core. This should not happen. Signed-off-by: Michal Oleszczyk <oleszczyk.m@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-02-12ASoC: sgtl5000: replace codec to componentKuninori Morimoto1-89/+84
Now we can replace Codec to Component. Let's do it. Note: xxx_codec_xxx() -> xxx_component_xxx() .idle_bias_off = 0 -> .idle_bias_on = 1 .ignore_pmdown_time = 0 -> .use_pmdown_time = 1 - -> .endianness = 1 - -> .non_legacy_dai_naming = 1 Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-01-18ASoC: sgtl5000: Clarify a bit about the ER1 meaningFabio Estevam1-1/+1
The "check ER1" message is not very clear about its meaning. Improve it a bit by referring to it as "ER1 erratum" so that it becomes clearer that ER1 references to a SGTL5000 erratum. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2018-01-18ASoC: sgtl5000: Do not print error on probe deferralFabio Estevam1-1/+4
When the MCLK is not yet available when the codec is probed, probe deferral will happen and in this case we should not print an error message. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2017-08-21Merge tag 'v4.13-rc6' into asoc-msm8916Mark Brown1-2/+2
Linux 4.13-rc6
2017-08-10ASoC: codecs: add const to snd_soc_codec_driver structuresBhumika Goyal1-1/+1
Declare snd_soc_codec_driver structures as const as they are only passed as an argument to the function snd_soc_register_codec. This argument is of type const, so declare the structures with this property as const. In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in a copy operation along with getting passed to snd_soc_register_codec. So, it can be made const too. Done using Coccinelle: @match disable optional_qualifier@ identifier s; position p; @@ static struct snd_soc_codec_driver s@p={...}; @good1@ identifier match.s; position p; @@ snd_soc_register_codec(...,&s@p,...) @bad@ identifier match.s; position p!={match.p,good1.p}; @@ s@p @depends on !bad disable optional_qualifier@ identifier match.s; @@ static +const struct snd_soc_codec_driver s={...}; Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2017-07-21ASoC: sgtl5000: Use snd_soc_kcontrol_codec()Fabio Estevam1-2/+2
Since commit a72952672005 ("ASoC: sgtl5000: add avc support") the following kernel crash happens after running a 'reboot' command: ALSA: Storing mixer settings... [ 20.031604] Unable to handle kernel paging request at virtual address fffffffe [ 20.039268] pgd = de2a0000 [ 20.041999] [fffffffe] *pgd=8fffd861, *pte=00000000, *ppte=00000000 [ 20.048387] Internal error: Oops: 80000007 [#1] SMP ARM The function that takes a kcontrol parameter and returns the codec that registered the control is snd_soc_kcontrol_codec(), so use the correct function to fix the problem. Fixes: a72952672005 ("ASoC: sgtl5000: add avc support") Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Richard Leitner <richard.leitner@skidata.com> Reviewed-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2017-06-14ASoC: sgtl5000: add avc supportRichard Leitner1-0/+89
The sgtl5000 features an automatic volume control block (AVC), which reduces loud signals and amplifies low level signals for easier listening. This patch adds support for this AVC block to the driver. Apart from the "AVC Switch" control which enables the block following controls for the configuration of AVC are added: + AVC Threshold Volume: threshold where audio is compressed when the measured level is above or expanded when below + AVC Max Gain Volume: maximum gain which can be applied when the measured audio level is below threshold + AVC Hard Limiter Switch: when enabled the signal is limited to the programmed threshold. + AVC Integrator Response: response time of the integrator The AVC block is enabled and configured using the DAP_AVC_CTRL and DAP_AVC_THRESHOLD registers. Following 2 checkpatch.pl strict checks are ignored because the indentation style is different for the struct snd_kcontrol_new definition: patch:147: CHECK: Alignment should match open parenthesis patch:150: CHECK: Alignment should match open parenthesis Signed-off-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-10ASoC: sgtl5000: Allow LRCLK pad drive strength to be changedFabio Estevam1-1/+18
Introduce the "lrclk-strength" property to allow LRCLK pad drive strength to be changed via device tree. When running a stress playback loop test on a mx6dl wandboard channel swap can be noticed on about 10% of the times. While debugging this issue I noticed that when probing the SGTL5000 LRCLK pin with the scope the swap did not happen. After removing the probe the swap started to happen again. After changing the LRCLK pad drive strength to the maximum value the issue is gone. Same fix works on a mx6dl Colibri board as well. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-09-29Merge remote-tracking branches 'asoc/topic/sgtl5000', 'asoc/topic/simple', ↵Mark Brown1-0/+3
'asoc/topic/stac9766', 'asoc/topic/sti' and 'asoc/topic/sunxi' into asoc-next
2016-09-01ASoC: sgtl5000: add headphone and LINEOUT mute controlsRichard Leitner1-0/+3
These controls mute/unmute the LINEOUT and headphone outputs of SGTL5000 using its CHIP_ANA_CTRL register. Signed-off-by: Richard Leitner <dev@g0hl1n.net> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-08-08ASoC: codec duplicated callback function goes to component on sgtl5000Kuninori Morimoto1-6/+8
codec driver and component driver has duplicated callback functions, and codec side functions are just copied to component side when register timing. This was quick-hack, but no longer needed. This patch moves these functions from codec driver to component driver. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-07-12sgtl5000: add Lineout volume controlKalle Kankare1-0/+10
This controls the volume for the line out pins of SGTL5000. Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-06-15ASoC: sgtl5000: Do not disable regulators in SND_SOC_BIAS_OFFEric Nelson1-30/+5
Disabling the SGTL5000 through regulators would certainly save more power than simply disabling the reference voltages as described in the data sheet, but won't properly restore things on resume. This driver does not support active regulators. So we simply disable the reference bias currents. Signed-off-by: Eric Nelson <eric@nelint.com> Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-06-15ASoC: sgtl5000: Disable internal PLL earlyEric Nelson1-1/+8
To handle the soft reboot case, the internal PLL must be disabled in SGTL5000_CHIP_CLK_CTRL before clearing bits SGTL5000_VCOAMP_POWERUP and SGTL5000_PLL_POWERUP in register SGTL5000_CHIP_ANA_POWER. Signed-off-by: Eric Nelson <eric@nelint.com> Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-06-15ASoC: sgtl5000: Initialize CHIP_ANA_POWER to power-on defaultsEric Nelson1-35/+21
Initialize CHIP_ANA_POWER to match power on defaults, which disables ADC, DAC, and charge pumps. In the process, remove references to the following register/bitfields from the sgtl5000_set_power_regs routine: CHIP_ANA_POWER/LINREG_SIMPLE_POWERUP and CHIP_LINREG_CTRL/LINREG_VDD_MASK And remove CHIP_ANA_POWER and CHIP_LINREG_CTRL from the set of default registers so they don't get clobbered by sgtl5000_fill_defaults(). Signed-off-by: Eric Nelson <eric@nelint.com> Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-06-15ASoC: sgtl5000: Write all default registersEric Nelson1-7/+6
If an error occurs writing defaults, produce an error message but continue writing other registers. The failure of a single write should not cause catastrophic device failure. In at least one occurrence, I2C writes of CHIP_ANA_POWER were nacked, though continuing allowed the device to operate properly. Signed-off-by: Eric Nelson <eric@nelint.com> Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-06-15ASoC: sgtl5000: Fix regulator supportEric Nelson1-265/+78
Regulator support on SGTL5000 is broken because the VDDIO and VDDA and VDDD should be powered on before enabling MCLK as shown in Figure 4 of [1]. This requires moving control of the regulators from the codec block to the I2C block of the driver. The bulk of this patch consists of swapping the codec device with the i2c client. The new field num_supplies in struct sgtl5000_priv is used instead of ARRAY_SIZE(supplies) to handle the special case when the internal LDO is used instead of external VDDD. Note that ER1 in the SGTL5000 Errata document [2] suggests that all designs should use external VDDD. Since the internal LDO can only be enabled after I2C is available, there's no benefit in treating it as a regulator, so this patch removes the regulator structure surrounding it. Instead, a single block of code in sgtl5000_i2c_probe() performs the initialization sequence in section 2.2.1.1 of [3] and page 26 of [1]. References: [1] SGTL5000 data sheet http://cache.nxp.com/files/analog/doc/data_sheet/SGTL5000.pdf [2] SGTL5000 errata http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf [3] SGTL5000 Initialization and programming app note http://cache.nxp.com/files/analog/doc/app_note/AN3663.pdf Signed-off-by: Eric Nelson <eric@nelint.com> Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2016-06-15ASoC: sgtl5000: Remove misleading commentClemens Gruber1-1/+0
All new designs should use external VDDD according to official documentation. See ER1 in errata sheet: http://cache.nxp.com/files/analog/doc/errata/SGTL5000ER.pdf Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-12-17ASoC: sgtl5000: fix VAG power up timingJean-Michel Hautbois1-0/+1
When power up, a "pop" is heard on line-in and mic-in. An analysis of the PCM shows it lasts ~400ms and looks like a filter response. VAG power up should be delayed by 400ms as VAG power down is. Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com> Signed-off-by: Mark Brown <broonie@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-28 20:28:52 +0300