| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
No added functionality
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
BIOS vendors sometimes declare multiple devices in the DSDT
table that all refer to the same HID. This is not very smart
but not illegal as long as only one device reports present with
the _STA method. The ACPI subsystem tracks each device with an
extension, e.g. 10EC5640:00 and 10EC5640:01
In the ASoC machine driver, the DAI codec name needs to refer to the
ACPI device that reported present, e.g. "i2c-10EC5640:01". The
extension will vary depending on how the BIOS is written and which
ACPI device is activated.
This patch adds a translation function that provides the codec
name from the ACPI HID to avoid any hard-coded values in the
machine driver.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
BIOS vendors typically list multiple audio codecs in the DSDT
table and enable the relevant one by changing the return value
of the _STA method.
With the current code, all devices are reported by
acpi_dev_present(), regardless of the _STA return values. This
causes errors on probe with the wrong machine driver being loaded.
This patch essentially reverts 'commit 6f08cbdaac5a
("ASoC: Intel: Use acpi_dev_present()")' and adds code to
force the evaluation of the _STA method.
A better solution might be to make sure the ACPI subsystem only
reports devices with a _STA value of 0xf but apparently it's
problematic so dealing with this in the audio subsystem directly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The IVI loop is removed in skl_nau88l25_ssm4567 machine as we
enable this path thru DAPM graph using the PCM device and not
thru loop
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We can enable the IVI feedback path by connecting Left/Right
speaker sensors (codec) to ssp0 Rx (soc-dsp). This way aDSP gets
feedback data from codec to DSP algorithms
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The blob query for BE skl_tplg_update_be_blob() was not using
right values for direction for blob query, so fix that.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
"Playback Switch" and "Lineout Mux" ctls in medfld machine driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The variable cmd_id is only assigned some value and is never used.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We cannot use strcpy() to write to a const char * location. This is
causing a 'BUG: unable to handle kernel paging request' error at boot
when using the cht-bsw-rt5645 driver.
With this patch we also fix a wrong indexing in the driver where the
codec_name of the wrong dai_link is being overwritten.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
WoV module needs to be triggered with PCM open, so remove this as
DAPM Sink and will be connected to FE
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
WoV module needs to be triggered with PCM open, so remove this as
DAPM Sink and will be connected to FE
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
WoV module needs to be triggered with PCM open, so remove this as
DAPM Sink and will be connected to FE
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SSM4567 supports IV feedback for feedback to the speaker
protection algorithm
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds 2 HDMI FE and BE dai links and also
initializes the jack for each device.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds 2 HDMI FE and BE dai links and also
initializes the jack for each device.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Skylake platform has 3 pin widgets in HDMI codec. This patch adds
3 FE and BE dai links to support these in rt286 machine
Also add jack initialization for each of the device.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dfw_ac->params is an array not a pointer. It will never be NULL. The check
on ac->max appears sufficient.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add missing DAPM pins and enable jack detection on those pins for
Cherrytrail and Braswell.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch enables HDMI support in passthrough mode in skylake.
Skylake supports 3 pin widgets in HDMI codec, so add 3 FE and 3
BE dais
Add required hw info, formats, rates to support HDMI.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SKL also supports HDMI output so in probe we need to enable
the HDMI using common i915 APIs to ensure it gets probed on the
bus
After S3 during the controller resequencing the codec domain need
to be kept ON for successful reconfiguration of Codec. Once
configured it will be turned OFF in codec driver.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set required parameters for hdac_ext_dma_params object instead of
skl_dma_params.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
NHLT table [1] header has fields like oem_id, oem_table_id and
oem_revision. Use that to load a unique topology binary specific
to that platform
NHLT Table is documented at:
[1]: https://01.org/blogs/2016/intel-smart-sound-technology-audio-dsp
Signed-off-by: Yang A Fang <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
skl_tplg_tlv_control_set does pointer maths on data but forgets that data
is not uint8_t so the maths is already scaled in the pointer type.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
|
|
When we have a path that connects to DSP sink and source, we
need to query the blob using the default params. So add a
function to query the params for such path
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While going to shutdown, we need to bring HW to clean state. This
is done by cleaning up stream descriptor registers. This cleanup
is already done by decoupling of stream and stopping the chip, so
invoke these from shutdown handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some modules require params to be set after the module is bound
to all the pins connected.
The module provider initializes set_param flag for such modules
and we send params after binding. This is done by the function
skl_tplg_set_module_bind_params()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SoC has MCLK output which is typically required by codecs.
The MCLK is controlled by DSP FW, so driver can configure that by
sending DMA_CONTROL IPC. The configuration for MCLK is present
in the endpoint blob.
So if block has this configuration, send IPC to DSP for MCLK
configuration. This is done by new function skl_dsp_set_dma_control()
which is invoked by BE prepare.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
An I2S port can be connected to multiple BE pipes, get module config
only for the active BE pipe.
This helpers helps to do that and is used in subsequent patches
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
skl_setup_cpr_gateway_cfg() retrieves gateway settings which are
required for copier module configuration. For upcoming DMA
control IPC we need similar retrieval, so separate this piece into
skl_get_node_id() helper which will be common for these functions
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Delay check was using ternary operator, it can be simplified to
simple if condition, so update it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel
|
|
The match module lacked module license and description, so add it
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DPCM driver is recommended for BYT, CHT based platforms, so if
CONFIG_SND_SST_IPC_ACPI is selected then don't compile the BYT
Device IDs in common ACPI driver to avoid probe conflicts.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ACPI match module is common to all three drivers, HSW, SKL
and Atom-DPCM driver. But Atom-DPCM driver does not use common
sst code so we cannot include the common SST module in Atom-DPCM
driver.
So the solution is to have a independent sst-match-acpi module
which helps in matching for all the three drivers. Now all driver
can be inbuilt in a single image
This patch really fixes the regression introduced by the
commit 95f098014815 ("ASoC: Intel: Move apci find machine routines")
Acked-by: Jie Yang <yang.jie@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
driver"
This reverts commit dc901a354171 ("ASoC: Intel: fix ACPI probe
regression with Atom DPCM driver") as the fix prevented the probe
on HSW/BDW if Atom-DPCM was selected
Acked-by: Jie Yang <yang.jie@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver used autosuspend delay to delay going to D3. But per
HW recommendation we should go to D3 soon, so remove the delay
from driver
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DMIC BE can have 2 or 4 channels supported. The DMIC fixup needs
to take this into account.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some modules may be directly connected to a pipeline without a
mixer module. For these modules, we require PRE_PMU and POST_PMU
handler which will do bind between the pipelines, so add these
missing handlers.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
skl_tplg_bind_sinks() takes only the first sink widget. This
breaks in case we have multiple sinks for a module.
So pass source widget to skl_tplg_bind_sinks() and bind for all
sinks by calling this recursively
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We should not stop the sink pipe in it's pmd handler for a mixin
module as this module may still be connected to other pipes.
This will be stopped and freed by current implementation on last
connected pipe unbind.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For binding modules we should check if source or destination
module is in UNINT state. We canot bind even if one of them is
in this state.
So update the check from logical AND to logical OR and do not
bind modules for this case
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In unbind modules, the skl_get_queue_index() can return error
if the pin is dynamic and module is not bound yet. So instead
of returning error this check should return success as modules
is not yet bound. This will let the module be bound when connected
pipes are enabled and will bind this as well.
So change the return value to 0
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We check and allocate pipeline resources in one shot. That causes
leaks if module creation fails later as that is not freed.
So split the resource allocation into two, first check if
resources are available and then add the resources upon
successful creation. So two new functions are added for checking
and current functions are re-purposed to only add the resources
for memory and MCPS.
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While cleaning resources on module pmd event, we check for return
of skl_unbind_modules(). On failure this causes leak as all modules
attached do not have resources freed.
So ignore return value of module unbind and continue freeing
resources. This makes dapm state and resources correct.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When delay reported by HW is equal to buffersize, it means the
value is wrapped so we should report as 0. So add the condition
to check this while reporting the delay from LPIB.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TLV buffer can be smaller than the module data, so update the
size of data to be copied before doing the copy.
Also TLV header consists of two unsigned ints, this is also taken
into account here and size modified to reflect this
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit a106804 ("ASoC: compress: Fix compress device direction check")
added a dependency on the compress-cpu-dai channel_min field
which was removed earlier by commit 77095796
("ASoC: Intel: Atom: clean-up compressed DAI definition")
as part of the baytrail cleanups.
The net result was a regression at probe on all Atom platforms
with no sound card created.
Fix by adding explicit initialization for channel_min to 1
for the compress-cpu-dai.
Reported-by: Tobias Mädel <alsa-devel@tbspace.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use shiny new acpi_dev_present() and remove all the boilerplate
to search for a particular ACPI device. No functional change.
Cf. 2d12b6b381ba ("ACPI / utils: Add acpi_dev_present()").
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
