From 7c558af511d01ef0ab0fe1692517f80d27e17cc3 Mon Sep 17 00:00:00 2001
From: Jonathan Bakker <xc-racer2@live.ca>
Date: Sat, 13 Jun 2020 11:44:25 -0700
Subject: ARM: dts: s5pv210: Add support for GP2A light sensor on Aries

Aries boards have a GP2A light/proximity sensor attached over i2c-gpio.
As the chip outputs a current and the board has no current ADC, a
current shunt resistor and a voltage ADC are used.

Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm/boot/dts/s5pv210-aries.dtsi | 50 ++++++++++++++++++++++++++++++++++--
 1 file changed, 48 insertions(+), 2 deletions(-)

(limited to 'arch/arm/boot/dts/s5pv210-aries.dtsi')

diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
index d3aeafc0f650..b27d7c2e6dca 100644
--- a/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ b/arch/arm/boot/dts/s5pv210-aries.dtsi
@@ -69,6 +69,18 @@
 		pinctrl-0 = <&touchkey_vdd_ena>;
 	};
 
+	gp2a_vled: regulator-fixed-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VLED";
+		enable-active-high;
+		gpio = <&gpj1 4 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gp2a_power>;
+	};
+
 	wifi_pwrseq: wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
@@ -468,9 +480,21 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&prox_i2c_pins>;
 
-		status = "disabled";
+		light-sensor@44 {
+			compatible = "sharp,gp2ap002a00f";
+			reg = <0x44>;
+			interrupt-parent = <&gph0>;
+			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+			vdd-supply = <&gp2a_vled>;
+			vio-supply = <&gp2a_vled>;
+			io-channels = <&gp2a_shunt>;
+			io-channel-names = "alsout";
+			sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
+			sharp,proximity-close-hysteresis = /bits/ 8 <0x20>;
 
-		/* Sharp gp2a prox/light sensor, incomplete mainline binding */
+			pinctrl-names = "default";
+			pinctrl-0 = <&gp2a_irq>;
+		};
 	};
 
 	i2c_magnetometer: i2c-gpio-7 {
@@ -543,6 +567,14 @@
 	vdd-supply = <&ldo4_reg>;
 
 	status = "okay";
+
+	gp2a_shunt: current-sense-shunt {
+		compatible = "current-sense-shunt";
+		io-channels = <&adc 9>;
+		shunt-resistor-micro-ohms = <47000000>; /* 47 ohms */
+		#io-channel-cells = <0>;
+		io-channel-ranges;
+	};
 };
 
 &fimd {
@@ -618,6 +650,13 @@
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
+	gp2a_irq: gp2a-irq {
+		samsung,pins = "gph0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
 	pmic_dvs_pins: pmic-dvs-pins {
 		samsung,pins = "gph0-3", "gph0-4", "gph0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
@@ -686,6 +725,13 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
+	gp2a_power: gp2a-power {
+		samsung,pins = "gpj1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
 	touchkey_i2c_pins: touchkey-i2c-pins {
 		samsung,pins = "gpj3-0", "gpj3-1";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-- 
cgit v1.2.3