From cf08fa74c716cf20e5038d1e7dbbd7dba1b76062 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Wed, 13 Sep 2023 16:29:17 +0800 Subject: regulator: mt6358: Add output voltage fine tuning to fixed regulators The "fixed" LDO regulators found on the MT6358 and MT6366 PMICs have either no voltage selection register, or only one valid setting. However these do have a fine voltage calibration setting that can slightly boost the output voltage from 0 mV to 100 mV, in 10 mV increments. Add support for this by changing these into linear range regulators. Some register definitions that are missing are also added. Signed-off-by: Chen-Yu Tsai Reviewed-by: AngeloGioacchino Del Regno Acked-by: Lee Jones Link: https://lore.kernel.org/r/20230913082919.1631287-3-wenst@chromium.org Signed-off-by: Mark Brown --- drivers/regulator/mt6358-regulator.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) (limited to 'drivers/regulator') diff --git a/drivers/regulator/mt6358-regulator.c b/drivers/regulator/mt6358-regulator.c index a1eae45f5fee..b34ad85db771 100644 --- a/drivers/regulator/mt6358-regulator.c +++ b/drivers/regulator/mt6358-regulator.c @@ -123,10 +123,13 @@ struct mt6358_regulator_info { .type = REGULATOR_VOLTAGE, \ .id = MT6358_ID_##vreg, \ .owner = THIS_MODULE, \ - .n_voltages = 1, \ + .n_voltages = 11, \ + .vsel_reg = MT6358_##vreg##_ANA_CON0, \ + .vsel_mask = GENMASK(3, 0), \ .enable_reg = enreg, \ .enable_mask = BIT(enbit), \ .min_uV = volt, \ + .uV_step = 10000, \ }, \ .status_reg = MT6358_LDO_##vreg##_CON1, \ .qi = BIT(15), \ @@ -219,10 +222,13 @@ struct mt6358_regulator_info { .type = REGULATOR_VOLTAGE, \ .id = MT6366_ID_##vreg, \ .owner = THIS_MODULE, \ - .n_voltages = 1, \ + .n_voltages = 11, \ + .vsel_reg = MT6358_##vreg##_ANA_CON0, \ + .vsel_mask = GENMASK(3, 0), \ .enable_reg = enreg, \ .enable_mask = BIT(enbit), \ .min_uV = volt, \ + .uV_step = 10000, \ }, \ .status_reg = MT6358_LDO_##vreg##_CON1, \ .qi = BIT(15), \ @@ -476,8 +482,13 @@ static const struct regulator_ops mt6358_volt_table_ops = { .get_status = mt6358_get_status, }; +/* "Fixed" LDOs with output voltage calibration +0 ~ +10 mV */ static const struct regulator_ops mt6358_volt_fixed_ops = { .list_voltage = regulator_list_voltage_linear, + .map_voltage = regulator_map_voltage_linear, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = mt6358_get_buck_voltage_sel, + .set_voltage_time_sel = regulator_set_voltage_time_sel, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, -- cgit v1.2.3