summaryrefslogtreecommitdiff
path: root/drivers/hwmon/pmbus/stpddc60.c
blob: 34d0f06f48452b2ab65a7b5302b00112458c4c65 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Hardware monitoring driver for the STPDDC60 controller
 *
 * Copyright (c) 2021 Flextronics International Sweden AB.
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/pmbus.h>
#include "pmbus.h"

#define STPDDC60_MFR_READ_VOUT		0xd2
#define STPDDC60_MFR_OV_LIMIT_OFFSET	0xe5
#define STPDDC60_MFR_UV_LIMIT_OFFSET	0xe6

static const struct i2c_device_id stpddc60_id[] = {
	{"stpddc60"},
	{"bmr481"},
	{}
};
MODULE_DEVICE_TABLE(i2c, stpddc60_id);

static struct pmbus_driver_info stpddc60_info = {
	.pages = 1,
	.func[0] = PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
		| PMBUS_HAVE_VIN | PMBUS_HAVE_STATUS_INPUT
		| PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP
		| PMBUS_HAVE_IOUT | PMBUS_HAVE_STATUS_IOUT
		| PMBUS_HAVE_POUT,
};

/*
 * Calculate the closest absolute offset between commanded vout value
 * and limit value in steps of 50mv in the range 0 (50mv) to 7 (400mv).
 * Return 0 if the upper limit is lower than vout or if the lower limit
 * is higher than vout.
 */
static u8 stpddc60_get_offset(int vout, u16 limit, bool over)
{
	int offset;
	long v, l;

	v = 250 + (vout - 1) * 5; /* Convert VID to mv */
	l = (limit * 1000L) >> 8; /* Convert LINEAR to mv */

	if (over == (l < v))
		return 0;

	offset = DIV_ROUND_CLOSEST(abs(l - v), 50);

	if (offset > 0)
		offset--;

	return clamp_val(offset, 0, 7);
}

/*
 * Adjust the linear format word to use the given fixed exponent.
 */
static u16 stpddc60_adjust_linear(u16 word, s16 fixed)
{
	s16 e, m, d;

	e = ((s16)word) >> 11;
	m = ((s16)((word & 0x7ff) << 5)) >> 5;
	d = e - fixed;

	if (d >= 0)
		m <<= d;
	else
		m >>= -d;

	return clamp_val(m, 0, 0x3ff) | ((fixed << 11) & 0xf800);
}

/*
 * The VOUT_COMMAND register uses the VID format but the vout alarm limit
 * registers use the LINEAR format so we override VOUT_MODE here to force
 * LINEAR format for all registers.
 */
static int stpddc60_read_byte_data(struct i2c_client *client, int page, int reg)
{
	int ret;

	if (page > 0)
		return -ENXIO;

	switch (reg) {
	case PMBUS_VOUT_MODE:
		ret = 0x18;
		break;
	default:
		ret = -ENODATA;
		break;
	}

	return ret;
}

/*
 * The vout related registers return values in LINEAR11 format when LINEAR16
 * is expected. Clear the top 5 bits to set the exponent part to zero to
 * convert the value to LINEAR16 format.
 */
static int stpddc60_read_word_data(struct i2c_client *client, int page,
				   int phase, int reg)
{
	int ret;

	if (page > 0)
		return -ENXIO;

	switch (reg) {
	case PMBUS_READ_VOUT:
		ret = pmbus_read_word_data(client, page, phase,
					   STPDDC60_MFR_READ_VOUT);
		if (ret < 0)
			return ret;
		ret &= 0x7ff;
		break;
	case PMBUS_VOUT_OV_FAULT_LIMIT:
	case PMBUS_VOUT_UV_FAULT_LIMIT:
		ret = pmbus_read_word_data(client, page, phase, reg);
		if (ret < 0)
			return ret;
		ret &= 0x7ff;
		break;
	default:
		ret = -ENODATA;
		break;
	}

	return ret;
}

/*
 * The vout under- and over-voltage limits are set as an offset relative to
 * the commanded vout voltage. The vin, iout, pout and temp limits must use
 * the same fixed exponent the chip uses to encode the data when read.
 */
static int stpddc60_write_word_data(struct i2c_client *client, int page,
				    int reg, u16 word)
{
	int ret;
	u8 offset;

	if (page > 0)
		return -ENXIO;

	switch (reg) {
	case PMBUS_VOUT_OV_FAULT_LIMIT:
		ret = pmbus_read_word_data(client, page, 0xff,
					   PMBUS_VOUT_COMMAND);
		if (ret < 0)
			return ret;
		offset = stpddc60_get_offset(ret, word, true);
		ret = pmbus_write_byte_data(client, page,
					    STPDDC60_MFR_OV_LIMIT_OFFSET,
					    offset);
		break;
	case PMBUS_VOUT_UV_FAULT_LIMIT:
		ret = pmbus_read_word_data(client, page, 0xff,
					   PMBUS_VOUT_COMMAND);
		if (ret < 0)
			return ret;
		offset = stpddc60_get_offset(ret, word, false);
		ret = pmbus_write_byte_data(client, page,
					    STPDDC60_MFR_UV_LIMIT_OFFSET,
					    offset);
		break;
	case PMBUS_VIN_OV_FAULT_LIMIT:
	case PMBUS_VIN_UV_FAULT_LIMIT:
	case PMBUS_OT_FAULT_LIMIT:
	case PMBUS_OT_WARN_LIMIT:
	case PMBUS_IOUT_OC_FAULT_LIMIT:
	case PMBUS_IOUT_OC_WARN_LIMIT:
	case PMBUS_POUT_OP_FAULT_LIMIT:
		ret = pmbus_read_word_data(client, page, 0xff, reg);
		if (ret < 0)
			return ret;
		word = stpddc60_adjust_linear(word, ret >> 11);
		ret = pmbus_write_word_data(client, page, reg, word);
		break;
	default:
		ret = -ENODATA;
		break;
	}

	return ret;
}

static int stpddc60_probe(struct i2c_client *client)
{
	int status;
	u8 device_id[I2C_SMBUS_BLOCK_MAX + 1];
	const struct i2c_device_id *mid;
	struct pmbus_driver_info *info = &stpddc60_info;

	if (!i2c_check_functionality(client->adapter,
				     I2C_FUNC_SMBUS_READ_BYTE_DATA
				     | I2C_FUNC_SMBUS_BLOCK_DATA))
		return -ENODEV;

	status = i2c_smbus_read_block_data(client, PMBUS_MFR_MODEL, device_id);
	if (status < 0) {
		dev_err(&client->dev, "Failed to read Manufacturer Model\n");
		return status;
	}
	for (mid = stpddc60_id; mid->name[0]; mid++) {
		if (!strncasecmp(mid->name, device_id, strlen(mid->name)))
			break;
	}
	if (!mid->name[0]) {
		dev_err(&client->dev, "Unsupported device\n");
		return -ENODEV;
	}

	info->read_byte_data = stpddc60_read_byte_data;
	info->read_word_data = stpddc60_read_word_data;
	info->write_word_data = stpddc60_write_word_data;

	status = pmbus_do_probe(client, info);
	if (status < 0)
		return status;

	pmbus_set_update(client, PMBUS_VOUT_OV_FAULT_LIMIT, true);
	pmbus_set_update(client, PMBUS_VOUT_UV_FAULT_LIMIT, true);

	return 0;
}

static struct i2c_driver stpddc60_driver = {
	.driver = {
		   .name = "stpddc60",
		   },
	.probe = stpddc60_probe,
	.id_table = stpddc60_id,
};

module_i2c_driver(stpddc60_driver);

MODULE_AUTHOR("Erik Rosen <erik.rosen@metormote.com>");
MODULE_DESCRIPTION("PMBus driver for ST STPDDC60");
MODULE_LICENSE("GPL");
MODULE_IMPORT_NS(PMBUS);