diff options
author | Peng Fan <Peng.Fan@freescale.com> | 2014-10-31 06:08:06 +0300 |
---|---|---|
committer | Stefano Babic <sbabic@denx.de> | 2014-11-20 12:13:53 +0300 |
commit | 05095535f6cab041a8c3007f6feae095a497bb92 (patch) | |
tree | dfcba243c1424fbb773ca647fd6f1716b73f4553 | |
parent | 7a139959d0de14a7efd0fe12b49b18e939468525 (diff) | |
download | u-boot-05095535f6cab041a8c3007f6feae095a497bb92.tar.xz |
imx:mx6sxsabresd fix pfuz probe failed
The PFUZ probe failed with the following msg:
" wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=0
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=1
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=2
i2c_init_transfer: give up i2c_regs=021a0000
Can't find PMIC:PFUZE100 "
board_early_init_f is too early to call i2c related setting, because
init_func_i2c is called after board_early_init_f being invoked. Thus
move setup_i2c into board_init.
Also PFUZ is connected to I2C bus 0, so change "1" -> "0".
Using this patch PFUZ can be correctly probed:
"PMIC: PFUZE100 ID=0x11"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
-rw-r--r-- | board/freescale/mx6sxsabresd/mx6sxsabresd.c | 5 |
1 files changed, 4 insertions, 1 deletions
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c index 68d37184a3..256ea29336 100644 --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c @@ -243,7 +243,6 @@ int board_phy_config(struct phy_device *phydev) int board_early_init_f(void) { setup_iomux_uart(); - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); /* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */ imx_iomux_v3_setup_multiple_pads(peri_3v3_pads, @@ -277,6 +276,10 @@ int board_init(void) /* Address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; +#ifdef CONFIG_SYS_I2C_MXC + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); +#endif + return 0; } |