arm: dts: imx8mm: sync dts from Linux Kernel

Sync dts for i.MX8MM from Linux Kernel 5.4.0-rc1

Signed-off-by: Peng Fan <peng.fan@nxp.com>

3 files changed, 456 insertions, 47 deletions

diff --git a/arch/arm/dts/imx8mm-evk-u-boot.dtsi b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
index 10d9a20f2a..16093f2067 100644
--- a/arch/arm/dts/imx8mm-evk-u-boot.dtsi
+++ b/arch/arm/dts/imx8mm-evk-u-boot.dtsi
@@ -3,7 +3,7 @@
  * Copyright 2019 NXP
  */
 
-&{/soc} {
+&{/soc@0} {
 	u-boot,dm-pre-reloc;
 	u-boot,dm-spl;
 };
diff --git a/arch/arm/dts/imx8mm-evk.dts b/arch/arm/dts/imx8mm-evk.dts
index 2d5d89475b..faefb7182a 100644
--- a/arch/arm/dts/imx8mm-evk.dts
+++ b/arch/arm/dts/imx8mm-evk.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/usb/pd.h>
 #include "imx8mm.dtsi"
 
 / {
@@ -37,6 +38,41 @@
 		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	wm8524: audio-codec {
+		#sound-dai-cells = <0>;
+		compatible = "wlf,wm8524";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_wlf>;
+		wlf,mute-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+	};
+
+	sound-wm8524 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "wm8524-audio";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&cpudai>;
+		simple-audio-card,bitclock-master = <&cpudai>;
+		simple-audio-card,widgets =
+			"Line", "Left Line Out Jack",
+			"Line", "Right Line Out Jack";
+		simple-audio-card,routing =
+			"Left Line Out Jack", "LINEVOUTL",
+			"Right Line Out Jack", "LINEVOUTR";
+
+		cpudai: simple-audio-card,cpu {
+			sound-dai = <&sai3>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&wm8524>;
+			clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
 };
 
 &fec1 {
@@ -54,19 +90,208 @@
 		ethphy0: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
-			at803x,led-act-blind-workaround;
-			at803x,eee-okay;
-			at803x,vddio-1p8v;
 		};
 	};
 };
 
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 GPIO_ACTIVE_LOW>;
+		rohm,reset-snvs-powered;
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			buck3_reg: BUCK3 {
+				// BUCK5 in datasheet
+				regulator-name = "BUCK3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4_reg: BUCK4 {
+				// BUCK6 in datasheet
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5_reg: BUCK5 {
+				// BUCK7 in datasheet
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				// BUCK8 in datasheet
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	ptn5110: tcpc@50 {
+		compatible = "nxp,ptn5110";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_typec1>;
+		reg = <0x50>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <11 8>;
+		status = "okay";
+
+		port {
+			typec1_dr_sw: endpoint {
+				remote-endpoint = <&usb1_drd_sw>;
+			};
+		};
+
+		typec1_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			data-role = "dual";
+			try-power-role = "sink";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+				     PDO_VAR(5000, 20000, 3000)>;
+			op-sink-microwatt = <15000000>;
+			self-powered;
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	pca6416: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &uart2 { /* console */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
 	status = "okay";
 };
 
+&usbotg1 {
+	dr_mode = "otg";
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		usb1_drd_sw: endpoint {
+			remote-endpoint = <&typec1_dr_sw>;
+		};
+	};
+};
+
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
@@ -124,12 +349,60 @@
 		>;
 	};
 
+	pinctrl_gpio_wlf: gpiowlfgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21	0xd6
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pmic: pmicirq {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x41
+		>;
+	};
+
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
 		>;
 	};
 
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC     0xd6
+			MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK      0xd6
+			MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK        0xd6
+			MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0     0xd6
+		>;
+	};
+
+	pinctrl_typec1: typec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_STROBE_GPIO2_IO11	0x159
+		>;
+	};
+
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX	0x140
diff --git a/arch/arm/dts/imx8mm.dtsi b/arch/arm/dts/imx8mm.dtsi
index 6b407a94c0..8aafad2449 100644
--- a/arch/arm/dts/imx8mm.dtsi
+++ b/arch/arm/dts/imx8mm.dtsi
@@ -44,6 +44,19 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		idle-states {
+			entry-method = "psci";
+
+			cpu_pd_wait: cpu-pd-wait {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x0010033>;
+				local-timer-stop;
+				entry-latency-us = <1000>;
+				exit-latency-us = <700>;
+				min-residency-us = <2700>;
+			};
+		};
+
 		A53_0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
@@ -53,6 +66,9 @@
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
+			cpu-idle-states = <&cpu_pd_wait>;
 		};
 
 		A53_1: cpu@1 {
@@ -64,6 +80,7 @@
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
+			cpu-idle-states = <&cpu_pd_wait>;
 		};
 
 		A53_2: cpu@2 {
@@ -75,6 +92,7 @@
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
+			cpu-idle-states = <&cpu_pd_wait>;
 		};
 
 		A53_3: cpu@3 {
@@ -86,6 +104,7 @@
 			enable-method = "psci";
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
+			cpu-idle-states = <&cpu_pd_wait>;
 		};
 
 		A53_L2: l2-cache0 {
@@ -100,12 +119,23 @@
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-microvolt = <850000>;
+			opp-supported-hw = <0xe>, <0x7>;
 			clock-latency-ns = <150000>;
+			opp-suspend;
 		};
 
 		opp-1600000000 {
 			opp-hz = /bits/ 64 <1600000000>;
 			opp-microvolt = <900000>;
+			opp-supported-hw = <0xc>, <0x7>;
+			clock-latency-ns = <150000>;
+			opp-suspend;
+		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <1000000>;
+			opp-supported-hw = <0x8>, <0x3>;
 			clock-latency-ns = <150000>;
 			opp-suspend;
 		};
@@ -158,15 +188,6 @@
 		clock-output-names = "clk_ext4";
 	};
 
-	gic: interrupt-controller@38800000 {
-		compatible = "arm,gic-v3";
-		reg = <0x0 0x38800000 0 0x10000>, /* GIC Dist */
-		      <0x0 0x38880000 0 0xC0000>; /* GICR (RD_base + SGI_base) */
-		#interrupt-cells = <3>;
-		interrupt-controller;
-		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
-	};
-
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
@@ -189,7 +210,23 @@
 		arm,no-tick-in-suspend;
 	};
 
-	soc {
+	usbphynop1: usbphynop1 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+		assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+		assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
+		clock-names = "main_clk";
+	};
+
+	usbphynop2: usbphynop2 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+		assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
+		assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
+		clock-names = "main_clk";
+	};
+
+	soc@0 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -199,17 +236,85 @@
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0x30000000 0x30000000 0x400000>;
+
+			sai1: sai@30010000 {
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30010000 0x10000>;
+				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI1_IPG>,
+					 <&clk IMX8MM_CLK_SAI1_ROOT>,
+					 <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 0 2 0>, <&sdma2 1 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai2: sai@30020000 {
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30020000 0x10000>;
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI2_IPG>,
+					<&clk IMX8MM_CLK_SAI2_ROOT>,
+					<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 2 2 0>, <&sdma2 3 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai3: sai@30030000 {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30030000 0x10000>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI3_IPG>,
+					 <&clk IMX8MM_CLK_SAI3_ROOT>,
+					 <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 4 2 0>, <&sdma2 5 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai5: sai@30050000 {
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30050000 0x10000>;
+				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI5_IPG>,
+					 <&clk IMX8MM_CLK_SAI5_ROOT>,
+					 <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 8 2 0>, <&sdma2 9 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			sai6: sai@30060000 {
+				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+				reg = <0x30060000 0x10000>;
+				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_SAI6_IPG>,
+					 <&clk IMX8MM_CLK_SAI6_ROOT>,
+					 <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>;
+				clock-names = "bus", "mclk1", "mclk2", "mclk3";
+				dmas = <&sdma2 10 2 0>, <&sdma2 11 2 0>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
 
 			gpio1: gpio@30200000 {
 				compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
 				reg = <0x30200000 0x10000>;
 				interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_GPIO1_ROOT>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				gpio-ranges = <&iomuxc 0 10 30>;
 			};
 
 			gpio2: gpio@30210000 {
@@ -217,10 +322,12 @@
 				reg = <0x30210000 0x10000>;
 				interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_GPIO2_ROOT>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				gpio-ranges = <&iomuxc 0 40 21>;
 			};
 
 			gpio3: gpio@30220000 {
@@ -228,10 +335,12 @@
 				reg = <0x30220000 0x10000>;
 				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_GPIO3_ROOT>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				gpio-ranges = <&iomuxc 0 61 26>;
 			};
 
 			gpio4: gpio@30230000 {
@@ -239,10 +348,12 @@
 				reg = <0x30230000 0x10000>;
 				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_GPIO4_ROOT>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				gpio-ranges = <&iomuxc 0 87 32>;
 			};
 
 			gpio5: gpio@30240000 {
@@ -250,10 +361,12 @@
 				reg = <0x30240000 0x10000>;
 				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_GPIO5_ROOT>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				gpio-ranges = <&iomuxc 0 119 30>;
 			};
 
 			wdog1: watchdog@30280000 {
@@ -313,12 +426,16 @@
 			};
 
 			ocotp: ocotp-ctrl@30350000 {
-				compatible = "fsl,imx8mm-ocotp", "fsl,imx7d-ocotp", "syscon";
+				compatible = "fsl,imx8mm-ocotp", "syscon";
 				reg = <0x30350000 0x10000>;
 				clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>;
 				/* For nvmem subnodes */
 				#address-cells = <1>;
 				#size-cells = <1>;
+
+				cpu_speed_grade: speed-grade@10 {
+					reg = <0x10 4>;
+				};
 			};
 
 			anatop: anatop@30360000 {
@@ -336,6 +453,8 @@
 					offset = <0x34>;
 					interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
 						     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MM_CLK_SNVS_ROOT>;
+					clock-names = "snvs-rtc";
 				};
 
 				snvs_pwrkey: snvs-powerkey {
@@ -344,6 +463,7 @@
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
+					status = "disabled";
 				};
 			};
 
@@ -355,10 +475,22 @@
 					 <&clk_ext3>, <&clk_ext4>;
 				clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2",
 					      "clk_ext3", "clk_ext4";
+				assigned-clocks = <&clk IMX8MM_CLK_NOC>,
+						<&clk IMX8MM_CLK_AUDIO_AHB>,
+						<&clk IMX8MM_CLK_IPG_AUDIO_ROOT>,
+						<&clk IMX8MM_SYS_PLL3>,
+						<&clk IMX8MM_VIDEO_PLL1>;
+				assigned-clock-parents = <&clk IMX8MM_SYS_PLL3_OUT>,
+							 <&clk IMX8MM_SYS_PLL1_800M>;
+				assigned-clock-rates = <0>,
+							<400000000>,
+							<400000000>,
+							<750000000>,
+							<594000000>;
 			};
 
 			src: reset-controller@30390000 {
-				compatible = "fsl,imx8mm-src", "syscon";
+				compatible = "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon";
 				reg = <0x30390000 0x10000>;
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				#reset-cells = <1>;
@@ -369,7 +501,7 @@
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0x30400000 0x30400000 0x400000>;
 
 			pwm1: pwm@30660000 {
 				compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
@@ -414,13 +546,21 @@
 				#pwm-cells = <2>;
 				status = "disabled";
 			};
+
+			system_counter: timer@306a0000 {
+				compatible = "nxp,sysctr-timer";
+				reg = <0x306a0000 0x20000>;
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&osc_24m>;
+				clock-names = "per";
+			};
 		};
 
 		aips3: bus@30800000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0x30800000 0x30800000 0x400000>;
 
 			ecspi1: spi@30820000 {
 				compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
@@ -554,7 +694,7 @@
 				compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b40000 0x10000>;
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clk IMX8MM_CLK_DUMMY>,
+				clocks = <&clk IMX8MM_CLK_IPG_ROOT>,
 					 <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
 					 <&clk IMX8MM_CLK_USDHC1_ROOT>;
 				clock-names = "ipg", "ahb", "per";
@@ -570,7 +710,7 @@
 				compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b50000 0x10000>;
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clk IMX8MM_CLK_DUMMY>,
+				clocks = <&clk IMX8MM_CLK_IPG_ROOT>,
 					 <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
 					 <&clk IMX8MM_CLK_USDHC2_ROOT>;
 				clock-names = "ipg", "ahb", "per";
@@ -584,7 +724,7 @@
 				compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b60000 0x10000>;
 				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clk IMX8MM_CLK_DUMMY>,
+				clocks = <&clk IMX8MM_CLK_IPG_ROOT>,
 					 <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
 					 <&clk IMX8MM_CLK_USDHC3_ROOT>;
 				clock-names = "ipg", "ahb", "per";
@@ -639,7 +779,7 @@
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0x32c00000 0x32c00000 0x400000>;
 
 			usbotg1: usb@32e40000 {
 				compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
@@ -647,23 +787,13 @@
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>;
 				clock-names = "usb1_ctrl_root_clk";
-				assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>,
-						  <&clk IMX8MM_CLK_USB_CORE_REF>;
-				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>,
-							 <&clk IMX8MM_SYS_PLL1_100M>;
+				assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>;
+				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				fsl,usbphy = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
 				status = "disabled";
 			};
 
-			usbphynop1: usbphynop1 {
-				compatible = "usb-nop-xceiv";
-				clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
-				assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
-				assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
-				clock-names = "main_clk";
-			};
-
 			usbmisc1: usbmisc@32e40200 {
 				compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc";
 				#index-cells = <1>;
@@ -676,23 +806,13 @@
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>;
 				clock-names = "usb1_ctrl_root_clk";
-				assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>,
-						  <&clk IMX8MM_CLK_USB_CORE_REF>;
-				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>,
-							 <&clk IMX8MM_SYS_PLL1_100M>;
+				assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>;
+				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				fsl,usbphy = <&usbphynop2>;
 				fsl,usbmisc = <&usbmisc2 0>;
 				status = "disabled";
 			};
 
-			usbphynop2: usbphynop2 {
-				compatible = "usb-nop-xceiv";
-				clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
-				assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
-				assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
-				clock-names = "main_clk";
-			};
-
 			usbmisc2: usbmisc@32e50200 {
 				compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc";
 				#index-cells = <1>;
@@ -729,5 +849,21 @@
 			dma-names = "rx-tx";
 			status = "disabled";
 		};
+
+		gic: interrupt-controller@38800000 {
+			compatible = "arm,gic-v3";
+			reg = <0x38800000 0x10000>, /* GIC Dist */
+			      <0x38880000 0xc0000>; /* GICR (RD_base + SGI_base) */
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		ddr-pmu@3d800000 {
+			compatible = "fsl,imx8mm-ddr-pmu", "fsl,imx8m-ddr-pmu";
+			reg = <0x3d800000 0x400000>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 };