net: replace the "xfi" phy-mode with "10gbase-r"

As part of the effort of making U-Boot work with the same device tree as
Linux, there is an issue with the "xfi" phy-mode. To be precise, in
Linux there was a discussion (for those who have time to read:
https://lore.kernel.org/netdev/1576768881-24971-2-git-send-email-madalin.bucur@oss.nxp.com/)

which led to a patch:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c114574ebfdf42f826776f717c8056a00fa94881

TL;DR: "xfi" was standardized in Linux as "10gbase-r".

This patch changes the relevant occurrences in U-Boot to use "10gbase-r"
instead of "xfi" wherever applicable.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>

38 files changed, 111 insertions, 102 deletions

diff --git a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
index d0103fc881..1a359d060e 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
@@ -1147,7 +1147,7 @@ int arch_early_init_r(void)
 #endif
 #ifdef CONFIG_SYS_FSL_HAS_RGMII
 	/* some dpmacs in armv8a based freescale layerscape SOCs can be
-	 * configured via both serdes(sgmii, xfi, xlaui etc) bits and via
+	 * configured via both serdes(sgmii, 10gbase-r, xlaui etc) bits and via
 	 * EC*_PMUX(rgmii) bits in RCW.
 	 * e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
 	 * serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
index f33d05d053..f2efd4cc1d 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
+++ b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
@@ -31,7 +31,7 @@ The LS1043A SoC includes the following function and features:
    - Hardware buffer management for buffer allocation and de-allocation (BMan)
    - Cryptography acceleration (SEC)
  - Ethernet interfaces by FMan
-   - Up to 1 x XFI supporting 10G interface
+   - Up to 1 x 10GBase-R supporting 10G interface
    - Up to 1 x QSGMII
    - Up to 4 x SGMII supporting 1000Mbps
    - Up to 2 x SGMII supporting 2500Mbps
@@ -190,7 +190,7 @@ The LS1046A SoC includes the following function and features:
    - Two PLLs per four-lane SerDes
    - Support for 10G operation
  - Ethernet interfaces by FMan
-   - Up to 2 x XFI supporting 10G interface (MAC 9, 10)
+   - Up to 2 x 10GBase-R supporting 10G interface (MAC 9, 10)
    - Up to 1 x QSGMII (MAC 5, 6, 10, 1)
    - Up to 4 x SGMII supporting 1000Mbps (MAC 5, 6, 9, 10)
    - Up to 3 x SGMII supporting 2500Mbps (MAC 5, 9, 10)
@@ -295,7 +295,7 @@ The LX2160A SoC includes the following function and features:
   Single WRIOP tile supporting 130Gbps using 18 MACs
   Support for 10G-SXGMII (aka USXGMII).
   Support for SGMII (and 1000Base-KX)
-  Support for XFI (and 10GBase-KR)
+  Support for 10GBase-R (and 10GBase-KR)
   Support for CAUI4 (100G); CAUI2 (50G) and 25G-AUI(25G).
   Support for XLAUI (and 40GBase-KR4) for 40G.
   Support for two RGMII parallel interfaces.
@@ -400,7 +400,7 @@ The LX2162A SoC includes the following function and features:
   Ethernet interfaces
   Support for 10G-SXGMII (aka USXGMII).
   Support for SGMII (and 1000Base-KX)
-  Support for XFI (and 10GBase-KR)
+  Support for 10GBase-R (and 10GBase-KR)
   Support for CAUI2 (50G) and 25G-AUI(25G).
   Support for XLAUI (and 40GBase-KR4) for 40G.
   Support for two RGMII parallel interfaces.
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c
index 280afbbf98..26f8a49826 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/ls1088a_serdes.c
@@ -100,7 +100,7 @@ enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
 	if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
 		return 0;
 	/*
-	 * LS1044A/1048A  support only one XFI port
+	 * LS1044A/1048A  support only one 10GBase-R port
 	 * Disable MAC1 for LS1044A/1048A
 	 */
 	if (serdes == FSL_SRDS_1 && lane == 2) {
diff --git a/arch/arm/dts/fsl-ls1088a-qds-sd1-21.dtsi b/arch/arm/dts/fsl-ls1088a-qds-sd1-21.dtsi
index e0a6c04835..df39cca696 100644
--- a/arch/arm/dts/fsl-ls1088a-qds-sd1-21.dtsi
+++ b/arch/arm/dts/fsl-ls1088a-qds-sd1-21.dtsi
@@ -9,12 +9,12 @@
 
 &dpmac1 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac2 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac4 {
diff --git a/arch/arm/dts/fsl-ls1088a-qds-sd1-29.dtsi b/arch/arm/dts/fsl-ls1088a-qds-sd1-29.dtsi
index 65e95300ab..99f74c2fc4 100644
--- a/arch/arm/dts/fsl-ls1088a-qds-sd1-29.dtsi
+++ b/arch/arm/dts/fsl-ls1088a-qds-sd1-29.dtsi
@@ -9,10 +9,10 @@
 
 &dpmac1 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac2 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
diff --git a/arch/arm/dts/fsl-ls2080a-qds-sd1-42.dtsi b/arch/arm/dts/fsl-ls2080a-qds-sd1-42.dtsi
index ccbb5de1ea..72297f48ca 100644
--- a/arch/arm/dts/fsl-ls2080a-qds-sd1-42.dtsi
+++ b/arch/arm/dts/fsl-ls2080a-qds-sd1-42.dtsi
@@ -9,40 +9,40 @@
 
 &dpmac1 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac2 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac3 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac4 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac5 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac6 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac7 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac8 {
 	status = "okay";
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
diff --git a/arch/arm/dts/fsl-ls2088a-rdb-qspi.dts b/arch/arm/dts/fsl-ls2088a-rdb-qspi.dts
index 179ed19bf2..9e68c147e6 100644
--- a/arch/arm/dts/fsl-ls2088a-rdb-qspi.dts
+++ b/arch/arm/dts/fsl-ls2088a-rdb-qspi.dts
@@ -24,49 +24,49 @@
 &dpmac1 {
 	status = "okay";
 	phy-handle = <&mdio1_phy1>;
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac2 {
 	status = "okay";
 	phy-handle = <&mdio1_phy2>;
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac3 {
 	status = "okay";
 	phy-handle = <&mdio1_phy3>;
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac4 {
 	status = "okay";
 	phy-handle = <&mdio1_phy4>;
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac5 {
 	status = "okay";
 	phy-handle = <&mdio2_phy1>;
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac6 {
 	status = "okay";
 	phy-handle = <&mdio2_phy2>;
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac7 {
 	status = "okay";
 	phy-handle = <&mdio2_phy3>;
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &dpmac8 {
 	status = "okay";
 	phy-handle = <&mdio2_phy4>;
-	phy-connection-type = "xfi";
+	phy-connection-type = "10gbase-r";
 };
 
 &emdio1 {
diff --git a/arch/arm/dts/fsl-sch-30841.dtsi b/arch/arm/dts/fsl-sch-30841.dtsi
index 2f1e63a6ae..3aa7fddc32 100644
--- a/arch/arm/dts/fsl-sch-30841.dtsi
+++ b/arch/arm/dts/fsl-sch-30841.dtsi
@@ -9,7 +9,7 @@
  * SCH-30841 is a 4 port add-on card used with various FSL QDS boards.
  * It integrates a AQR412C quad PHY which supports 4 interfaces either muxed
  * together on a single lane or mapped 1:1 to serdes lanes.
- * It supports several protocols - SGMII, SGMII-2500, USXGMII, M-USX, XFI.
+ * It supports several protocols - SGMII, SGMII-2500, USXGMII, M-USX, 10GBase-R.
  * PHY addresses are 0x00 - 0x03.
  * On the card the first port is the bottom port (closest to PEX connector).
  */
diff --git a/arch/arm/dts/fsl-sch-30842.dtsi b/arch/arm/dts/fsl-sch-30842.dtsi
index 6a68b1849e..b3c0c2bc35 100644
--- a/arch/arm/dts/fsl-sch-30842.dtsi
+++ b/arch/arm/dts/fsl-sch-30842.dtsi
@@ -8,7 +8,7 @@
 /*
  * SCH-30842 is a single port add-on card used with various FSL QDS boards.
  * It integrates a AQR112 PHY, which supports several protocols - SGMII,
- * SGMII-2500, USXGMII, XFI.
+ * SGMII-2500, USXGMII, 10GBase-R.
  * PHY address is 0x02.
  */
 phy@02 {
diff --git a/board/Marvell/octeon_ebb7304/board.c b/board/Marvell/octeon_ebb7304/board.c
index 9aac5f0b09..e8e2d547c1 100644
--- a/board/Marvell/octeon_ebb7304/board.c
+++ b/board/Marvell/octeon_ebb7304/board.c
@@ -339,7 +339,7 @@ void __fixup_fdt(void)
 		case CVMX_QLM_MODE_XFI:
 		case CVMX_QLM_MODE_RGMII_XFI:
 		case CVMX_QLM_MODE_RGMII_XFI_1X1:
-			type_str = "xfi";
+			type_str = "10gbase-r";
 			break;
 		case CVMX_QLM_MODE_10G_KR:
 		case CVMX_QLM_MODE_RGMII_10G_KR:
@@ -393,7 +393,7 @@ void __fixup_fdt(void)
 				if (pmd_control.s.train_en)
 					type_str = "10G_KR";
 				else
-					type_str = "xfi";
+					type_str = "10gbase-r";
 				break;
 			case 4:
 				if (pmd_control.s.train_en)
@@ -618,7 +618,7 @@ static void board_configure_qlms(void)
 					speed[qlm] = 103125;
 			}
 			printf("QLM %d: XLAUI\n", qlm);
-		} else if (!strncmp(mode_str, "xfi", 3)) {
+		} else if (!strncmp(mode_str, "10gbase-r", 3)) {
 			bool rgmii = false;
 
 			speed[qlm] = 103125;
diff --git a/board/freescale/ls1043aqds/README b/board/freescale/ls1043aqds/README
index 913537d451..f5aa51da87 100644
--- a/board/freescale/ls1043aqds/README
+++ b/board/freescale/ls1043aqds/README
@@ -18,7 +18,7 @@ SoC overview.
       - SGMII, SGMII 2.5
       - QSGMII
       - SATA 3.0
-      - XFI
+      - 10GBase-R
  - DDR Controller
      - 2GB 40bits (8-bits ECC) DDR4 SDRAM. Support rates of up to 1600MT/s
  -IFC/Local Bus
diff --git a/board/freescale/ls1043aqds/eth.c b/board/freescale/ls1043aqds/eth.c
index c3efe8a0be..81e18f6e82 100644
--- a/board/freescale/ls1043aqds/eth.c
+++ b/board/freescale/ls1043aqds/eth.c
@@ -242,13 +242,13 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
 				   "qsgmii");
 	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII &&
 		   port == FM1_10GEC1) {
-		/* XFI interface */
+		/* 10GBase-R interface */
 		f_link.phy_id = cpu_to_fdt32(port);
 		f_link.duplex = cpu_to_fdt32(1);
 		f_link.link_speed = cpu_to_fdt32(10000);
 		f_link.pause = 0;
 		f_link.asym_pause = 0;
-		/* no PHY for XFI */
+		/* no PHY for 10GBase-R */
 		fdt_delprop(fdt, offset, "phy-handle");
 		fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link));
 		fdt_setprop_string(fdt, offset, "phy-connection-type", "xgmii");
diff --git a/board/freescale/ls1043ardb/README b/board/freescale/ls1043ardb/README
index 709ddbbef3..66ee578e99 100644
--- a/board/freescale/ls1043ardb/README
+++ b/board/freescale/ls1043ardb/README
@@ -17,7 +17,7 @@ SoC overview.
       - PCI Express 2.0 with two PCIe connectors supporting: miniPCIe card and
         standard PCIe card
       - QSGMII with x4 RJ45 connector
-      - XFI with x1 RJ45 connector
+      - 10GBase-R with x1 RJ45 connector
  - DDR Controller
      - 2GB 32bits DDR4 SDRAM. Support rates of up to 1600MT/s
  -IFC/Local Bus
diff --git a/board/freescale/ls1043ardb/eth.c b/board/freescale/ls1043ardb/eth.c
index 1f01c15516..fa59116ce5 100644
--- a/board/freescale/ls1043ardb/eth.c
+++ b/board/freescale/ls1043ardb/eth.c
@@ -65,7 +65,7 @@ int board_eth_init(struct bd_info *bis)
 	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++)
 		fm_info_set_mdio(i, dev);
 
-	/* XFI on lane A, MAC 9 */
+	/* 10GBase-R on lane A, MAC 9 */
 	fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
 	dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
 	fm_info_set_mdio(FM1_10GEC1, dev);
diff --git a/board/freescale/ls1046aqds/README b/board/freescale/ls1046aqds/README
index b8fa32652b..d6469019bd 100644
--- a/board/freescale/ls1046aqds/README
+++ b/board/freescale/ls1046aqds/README
@@ -18,7 +18,7 @@ SoC overview.
       - SGMII, SGMII 2.5
       - QSGMII
       - SATA 3.0
-      - XFI
+      - 10GBase-R
  - DDR Controller
      - 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s
  -IFC/Local Bus
diff --git a/board/freescale/ls1046aqds/eth.c b/board/freescale/ls1046aqds/eth.c
index 33db552adb..2352832466 100644
--- a/board/freescale/ls1046aqds/eth.c
+++ b/board/freescale/ls1046aqds/eth.c
@@ -217,13 +217,13 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
 			/* Backplane KR mode: skip fixups */
 			printf("Interface %d in backplane KR mode\n", port);
 		} else {
-			/* XFI interface */
+			/* 10GBase-R interface */
 			f_link.phy_id = cpu_to_fdt32(port);
 			f_link.duplex = cpu_to_fdt32(1);
 			f_link.link_speed = cpu_to_fdt32(10000);
 			f_link.pause = 0;
 			f_link.asym_pause = 0;
-			/* no PHY for XFI */
+			/* no PHY for 10GBase-R */
 			fdt_delprop(fdt, offset, "phy-handle");
 			fdt_setprop(fdt, offset, "fixed-link", &f_link,
 				    sizeof(f_link));
diff --git a/board/freescale/ls1046ardb/README b/board/freescale/ls1046ardb/README
index a38c9d4830..1660f7c7cf 100644
--- a/board/freescale/ls1046ardb/README
+++ b/board/freescale/ls1046ardb/README
@@ -14,8 +14,8 @@ SoC overview.
  LS1046ARDB board Overview
  -----------------------
  - SERDES1 Connections, 4 lanes supporting:
-      - Lane0: XFI with x1 RJ45 connector
-      - Lane1: XFI Cage
+      - Lane0: 10GBase-R with x1 RJ45 connector
+      - Lane1: 10GBase-R Cage
       - Lane2: SGMII.5
       - Lane3: SGMII.6
  - SERDES2 Connections, 4 lanes supporting:
diff --git a/board/freescale/ls1046ardb/eth.c b/board/freescale/ls1046ardb/eth.c
index 4905302d8c..a3e147a48b 100644
--- a/board/freescale/ls1046ardb/eth.c
+++ b/board/freescale/ls1046ardb/eth.c
@@ -67,7 +67,7 @@ int board_eth_init(struct bd_info *bis)
 	for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++)
 		fm_info_set_mdio(i, dev);
 
-	/* XFI on lane A, MAC 9 */
+	/* 10GBase-R on lane A, MAC 9 */
 	dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
 	fm_info_set_mdio(FM1_10GEC1, dev);
 
diff --git a/board/freescale/ls1088a/README b/board/freescale/ls1088a/README
index aa0fb6ac67..5315909def 100644
--- a/board/freescale/ls1088a/README
+++ b/board/freescale/ls1088a/README
@@ -42,7 +42,7 @@ Alternately you can use this command to switch from QSPI to SD
  - SERDES Connections, 16 lanes supporting:
       - PCI Express - 3.0
       - SATA 3.0
-      - XFI
+      - 10GBase-R
       - QSGMII
  - DDR Controller
      - One ports of 72-bits (8-bits ECC, 64-bits DATA) DDR4. Each port supports four
@@ -106,7 +106,7 @@ SW12 1111 1111
  - SERDES Connections, 16 lanes supporting:
       - PCI Express - 3.0
       - SATA 3.0
-      - 2 XFI
+      - 2 10GBase-R
       - QSGMII, SGMII with help for Riser card
       - 2 RGMII
       - 5 slot for Riser card or PCIe NIC
diff --git a/board/freescale/ls1088a/eth_ls1088ardb.c b/board/freescale/ls1088a/eth_ls1088ardb.c
index a8e9ef15dc..1ba5e94d0a 100644
--- a/board/freescale/ls1088a/eth_ls1088ardb.c
+++ b/board/freescale/ls1088a/eth_ls1088ardb.c
@@ -52,9 +52,9 @@ int board_eth_init(struct bd_info *bis)
 	switch (srds_s1) {
 	case 0x1D:
 		/*
-		 * XFI does not need a PHY to work, but to avoid U-boot use
-		 * default PHY address which is zero to a MAC when it found
-		 * a MAC has no PHY address, we give a PHY address to XFI
+		 * 10GBase-R does not need a PHY to work, but to avoid U-boot
+		 * use default PHY address which is zero to a MAC when it found
+		 * a MAC has no PHY address, we give a PHY address to 10GBase-R
 		 * MAC error.
 		 */
 		wriop_set_phy_address(WRIOP1_DPMAC1, 0, 0x0a);
diff --git a/board/freescale/ls2080aqds/README b/board/freescale/ls2080aqds/README
index 8e31e9e41e..04c1941b05 100644
--- a/board/freescale/ls2080aqds/README
+++ b/board/freescale/ls2080aqds/README
@@ -19,7 +19,7 @@ LS2088A SoC overview.
       - QSGMII
       - SATA 3.0
       - XAUI
-      - XFI
+      - 10GBase-R
  - DDR Controller
      - Two ports of 72-bits (8-bits ECC) DDR4. Each port supports four
        chip-selects and two DIMM connectors. Support is up to 2133MT/s.
diff --git a/board/freescale/ls2080aqds/eth.c b/board/freescale/ls2080aqds/eth.c
index 914cd0a9ab..7db3789822 100644
--- a/board/freescale/ls2080aqds/eth.c
+++ b/board/freescale/ls2080aqds/eth.c
@@ -874,13 +874,12 @@ void ls2080a_handle_phy_interface_xsgmii(int i)
 	case 0x4B:
 	case 0x4C:
 		/*
-		 * XFI does not need a PHY to work, but to avoid U-Boot use
-		 * default PHY address which is zero to a MAC when it found
-		 * a MAC has no PHY address, we give a PHY address to XFI
-		 * MAC, and should not use a real XAUI PHY address, since
-		 * MDIO can access it successfully, and then MDIO thinks
-		 * the XAUI card is used for the XFI MAC, which will cause
-		 * error.
+		 * 10GBase-R does not need a PHY to work, but to avoid U-Boot
+		 * use default PHY address which is zero to a MAC when it found
+		 * a MAC has no PHY address, we give a PHY address to 10GBase-R
+		 * MAC, and should not use a real XAUI PHY address, since MDIO
+		 * can access it successfully, and then MDIO thinks the XAUI
+		 * card is used for the 10GBase-R MAC, which will cause error.
 		 */
 		wriop_set_phy_address(i, 0, i + 4);
 		ls2080a_qds_enable_SFP_TX(SFP_TX);
diff --git a/board/freescale/ls2080ardb/README b/board/freescale/ls2080ardb/README
index 205c45cb2a..75a633ccb4 100644
--- a/board/freescale/ls2080ardb/README
+++ b/board/freescale/ls2080ardb/README
@@ -18,7 +18,7 @@ LS2081A, LS2088A SoC overview.
  - SERDES Connections, 16 lanes supporting:
       - PCI Express - 3.0
       - SATA 3.0
-      - XFI
+      - 10GBase-R
  - DDR Controller
      - Two ports of 72-bits (8-bits ECC) DDR4. Each port supports four
        chip-selects and two DIMM connectors. Support is up to 2133MT/s.
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
index dde3f8ca37..84deb9562a 100644
--- a/board/freescale/t102xrdb/README
+++ b/board/freescale/t102xrdb/README
@@ -39,7 +39,7 @@ The T1024 SoC includes the following function and features:
   - One QSGMII interface
   - Four SGMII interface supporting 1000 Mbps
   - Three SGMII interfaces supporting up to 2500 Mbps
-  - 10GbE XFI or 10Base-KR interface
+  - 10GBase-R or 10Base-KR interface
 - Additional peripheral interfaces
   - Two USB 2.0 controllers with integrated PHY
   - SD/eSDHC/eMMC
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
index 56e6109288..b28c5457d6 100644
--- a/board/freescale/t102xrdb/eth_t102xrdb.c
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -64,7 +64,7 @@ int board_eth_init(struct bd_info *bis)
 		/* set the on-board RGMII2  PHY */
 		fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
 
-		/* set 10G XFI with Aquantia AQR105 PHY */
+		/* set 10GBase-R with Aquantia AQR105 PHY */
 		fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
 		break;
 #endif
diff --git a/board/freescale/t208xqds/README b/board/freescale/t208xqds/README
index d690857f2e..b52d9610e9 100755
--- a/board/freescale/t208xqds/README
+++ b/board/freescale/t208xqds/README
@@ -55,14 +55,14 @@ Memory:
  - Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
 Ethernet interfaces:
  - Two 1Gbps RGMII on-board ports
- - Four 10Gbps XFI on-board cages
+ - Four 10GBase-R on-board cages
  - 1Gbps/2.5Gbps SGMII Riser card
  - 10Gbps XAUI Riser card
 Accelerator:
  - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
 SerDes:
  - 16 lanes up to 10.3125GHz
- - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
+ - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, 10GBase-R and XAUI
 IFC:
  - 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
 eSPI:
@@ -85,14 +85,14 @@ System Logic:
  - QIXIS-II FPGA system controll
 Debug Features:
  - Support Legacy, COP/JTAG, Aurora, Event and EVT
-XFI:
- - XFI is supported on T2080QDS through Lane A/B/C/D on Serdes 1 routed to
+10GBase-R:
+ - 10GBase-R is supported on T2080QDS through Lane A/B/C/D on Serdes 1 routed to
  a on-board SFP+ cages, which to house optical module (fiber cable) or
  direct attach cable(copper), the copper cable is used to emulate
  10GBASE-KR scenario.
- So, for XFI usage, there are two scenarios, one will use fiber cable,
+ So, for 10GBase-R usage, there are two scenarios, one will use fiber cable,
  another will use copper cable. An hwconfig env "fsl_10gkr_copper" is
- introduced to indicate a XFI port will use copper cable, and U-Boot
+ introduced to indicate a 10GBase-R port will use copper cable, and U-Boot
  will fixup the dtb accordingly.
  It's used as: fsl_10gkr_copper:<10g_mac_name>
  The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4, they
@@ -100,10 +100,10 @@ XFI:
  "fsl_10gkr_copper", it will use copper cable, otherwise, fiber cable
  will be used by default.
  for ex. set "fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4" in
- hwconfig, then both four XFI ports will use copper cable.
+ hwconfig, then both four 10GBase-R ports will use copper cable.
  set "fsl_10gkr_copper:fm1_10g1,fm1_10g2" in hwconfig, then first two
- XFI ports will use copper cable, the other two XFI ports will use fiber
- cable.
+ 10GBase-R ports will use copper cable, the other two 10GBase-R ports will use
+ fiber cable.
 1000BASE-KX(1G-KX):
  - T2080QDS can support 1G-KX by using SGMII protocol, but serdes lane
  runs in 1G-KX mode. By default, the lane runs in SGMII mode, to set a lane
diff --git a/board/freescale/t208xqds/eth_t208xqds.c b/board/freescale/t208xqds/eth_t208xqds.c
index 705387af3c..2d7fc8bdda 100644
--- a/board/freescale/t208xqds/eth_t208xqds.c
+++ b/board/freescale/t208xqds/eth_t208xqds.c
@@ -310,16 +310,16 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
 
 	} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
 		switch (srds_s1) {
-		case 0x66: /* XFI interface */
+		case 0x66: /* 10GBase-R interface */
 		case 0x6b:
 		case 0x6c:
 		case 0x6d:
 		case 0x71:
 			/*
-			* if the 10G is XFI, check hwconfig to see what is the
-			* media type, there are two types, fiber or copper,
-			* fix the dtb accordingly.
-			*/
+			 * Check hwconfig to see what is the media type, there
+			 * are two types, fiber or copper, fix the dtb
+			 * accordingly.
+			 */
 			switch (port) {
 			case FM1_10GEC1:
 			if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g1")) {
@@ -378,7 +378,7 @@ void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
 					printf("Interface %d in backplane KR mode\n",
 					       port);
 				} else {
-					/* fixed-link for XFI fiber cable */
+					/* fixed-link for 10GBase-R fiber cable */
 					f_link.phy_id = port;
 					f_link.duplex = 1;
 					f_link.link_speed = 10000;
@@ -538,12 +538,12 @@ int board_eth_init(struct bd_info *bis)
 	case 0x66:
 	case 0x67:
 		/*
-		 * XFI does not need a PHY to work, but to avoid U-Boot use
-		 * default PHY address which is zero to a MAC when it found
-		 * a MAC has no PHY address, we give a PHY address to XFI
+		 * 10GBase-R does not need a PHY to work, but to avoid U-Boot
+		 * use default PHY address which is zero to a MAC when it found
+		 * a MAC has no PHY address, we give a PHY address to 10GBase-R
 		 * MAC, and should not use a real XAUI PHY address, since
 		 * MDIO can access it successfully, and then MDIO thinks
-		 * the XAUI card is used for the XFI MAC, which will cause
+		 * the XAUI card is used for the 10GBase-R MAC, which will cause
 		 * error.
 		 */
 		fm_info_set_phy_address(FM1_10GEC1, 4);
@@ -701,7 +701,7 @@ int board_eth_init(struct bd_info *bis)
 			    (srds_s1 == 0x6a) || (srds_s1 == 0x70) ||
 			    (srds_s1 == 0x6c) || (srds_s1 == 0x6d) ||
 			    (srds_s1 == 0x71)) {
-				/* As XFI is in cage intead of a slot, so
+				/* As 10GBase-R is in cage intead of a slot, so
 				 * ensure doesn't disable the corresponding port
 				 */
 				break;
diff --git a/board/freescale/t208xqds/t208xqds.c b/board/freescale/t208xqds/t208xqds.c
index 715de106d6..e54672a80b 100644
--- a/board/freescale/t208xqds/t208xqds.c
+++ b/board/freescale/t208xqds/t208xqds.c
@@ -136,14 +136,14 @@ int brd_mux_lane_to_slot(void)
 		break;
 	case 0x66:
 	case 0x67:
-		/* SD1(A:D) => XFI cage
+		/* SD1(A:D) => 10GBase-R cage
 		 * SD1(E:H) => SLOT1 PCIe4
 		 */
 		QIXIS_WRITE(brdcfg[12], 0xfe);
 		break;
 	case 0x6a:
 	case 0x6b:
-		/* SD1(A:D) => XFI cage
+		/* SD1(A:D) => 10GBase-R cage
 		 * SD1(E)   => SLOT1 PCIe4
 		 * SD1(F:H) => SLOT2 SGMII
 		 */
@@ -151,14 +151,14 @@ int brd_mux_lane_to_slot(void)
 		break;
 	case 0x6c:
 	case 0x6d:
-		/* SD1(A:B) => XFI cage
+		/* SD1(A:B) => 10GBase-R cage
 		 * SD1(C:D) => SLOT3 SGMII
 		 * SD1(E:H) => SLOT1 PCIe4
 		 */
 		QIXIS_WRITE(brdcfg[12], 0xda);
 		break;
 	case 0x6e:
-		/* SD1(A:B) => SFP Module, XFI
+		/* SD1(A:B) => SFP Module, 10GBase-R
 		 * SD1(C:D) => SLOT3 SGMII
 		 * SD1(E:F) => SLOT1 PCIe4 x2
 		 * SD1(G:H) => SLOT2 SGMII
diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README
index ec47c96f2b..c4bfd3b466 100644
--- a/board/freescale/t208xrdb/README
+++ b/board/freescale/t208xrdb/README
@@ -54,7 +54,7 @@ Differences between T2080 and T2081
 T2080PCIe-RDB board Overview
 ----------------------------
  - SERDES Configuration
-     - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
+     - SerDes-1 Lane A-B: to two 10GBase-R fiber (MAC9 & MAC10)
      - SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
      - SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
      - SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
@@ -62,7 +62,7 @@ T2080PCIe-RDB board Overview
      - SerDes-2 Lane G-H: to SATA1 & SATA2
  - Ethernet
      - Two on-board 10M/100M/1G RGMII ethernet ports
-     - Two on-board 10Gbps XFI fiber ports
+     - Two on-board 10GBase-R fiber ports
      - Two on-board 10Gbps Base-T copper ports
  - DDR Memory
      - Supports 72bit 4GB DDR3-LP SODIMM
diff --git a/board/freescale/t4rdb/eth.c b/board/freescale/t4rdb/eth.c
index c815a3a4fa..34ffaa6aeb 100644
--- a/board/freescale/t4rdb/eth.c
+++ b/board/freescale/t4rdb/eth.c
@@ -106,7 +106,7 @@ int board_eth_init(struct bd_info *bis)
 
 #if (CONFIG_SYS_NUM_FMAN == 2)
 	if ((srds_prtcl_s2 == 56) || (srds_prtcl_s2 == 55)) {
-		/* SGMII && XFI */
+		/* SGMII && 10GBase-R */
 		fm_info_set_phy_address(FM2_DTSEC1, SGMII_PHY_ADDR5);
 		fm_info_set_phy_address(FM2_DTSEC2, SGMII_PHY_ADDR6);
 		fm_info_set_phy_address(FM2_DTSEC3, SGMII_PHY_ADDR7);
diff --git a/doc/device-tree-bindings/net/ethernet.txt b/doc/device-tree-bindings/net/ethernet.txt
index cfc376bc97..648a1aee69 100644
--- a/doc/device-tree-bindings/net/ethernet.txt
+++ b/doc/device-tree-bindings/net/ethernet.txt
@@ -41,7 +41,17 @@ Documentation/devicetree/bindings/phy/phy-bindings.txt.
   * "2500base-x",
   * "rxaui"
   * "xaui"
-  * "10gbase-kr" (10GBASE-KR, XFI, SFI)
+  * "10gbase-r" (This is the IEEE 802.3 Clause 49 defined 10GBASE-R protocol
+    used with various different mediums. Please refer to the IEEE standard for
+    a definition of this. Note: 10GBASE-R is just one protocol that can be used
+    with XFI and SFI. XFI and SFI permit multiple protocols over a single
+    SERDES lane, and also defines the electrical characteristics of the signals
+    with a host compliance board plugged into the host XFP/SFP connector.
+    Therefore, XFI and SFI are not PHY interface types in their own right.)
+  * "10gbase-kr" (This is the IEEE 802.3 Clause 49 defined 10GBASE-R with
+    Clause 73 autonegotiation. Please refer to the IEEE standard for further
+    information. Note: due to legacy usage, some 10GBASE-R usage incorrectly
+    makes use of this definition).
 - phy-connection-type: the same as "phy-mode" property but described in the
   Devicetree Specification;
 - phy-handle: phandle, specifies a reference to a node representing a PHY
diff --git a/drivers/net/fm/b4860.c b/drivers/net/fm/b4860.c
index 5be0ad2ab3..6e3d008199 100644
--- a/drivers/net/fm/b4860.c
+++ b/drivers/net/fm/b4860.c
@@ -100,7 +100,7 @@ phy_interface_t fman_port_enet_if(enum fm_port port)
 			env_get_f("hwconfig", buffer, sizeof(buffer));
 			buf = buffer;
 
-			/* check if XFI interface enable in hwconfig for 10g */
+			/* check if 10GBase-R interface enable in hwconfig for 10g */
 			if (hwconfig_subarg_cmp_f("fsl_b4860_serdes2",
 						  "sfp_amc", "sfp", buf)) {
 				if ((port == FM1_10GEC1 ||
diff --git a/drivers/net/fm/memac.c b/drivers/net/fm/memac.c
index 36f50d2782..e1f812b688 100644
--- a/drivers/net/fm/memac.c
+++ b/drivers/net/fm/memac.c
@@ -98,7 +98,7 @@ static void memac_set_interface_mode(struct fsl_enet_mac *mac,
 		if_mode &= ~IF_MODE_MASK;
 		if_mode |= (IF_MODE_GMII);
 		break;
-	case PHY_INTERFACE_MODE_XFI:
+	case PHY_INTERFACE_MODE_10GBASER:
 	case PHY_INTERFACE_MODE_XGMII:
 		if_mode &= ~IF_MODE_MASK;
 		if_mode |= IF_MODE_XGMII;
@@ -107,7 +107,7 @@ static void memac_set_interface_mode(struct fsl_enet_mac *mac,
 		break;
 	}
 	/* Enable automatic speed selection for Non-XGMII */
-	if (type != PHY_INTERFACE_MODE_XGMII && type != PHY_INTERFACE_MODE_XFI)
+	if (type != PHY_INTERFACE_MODE_XGMII && type != PHY_INTERFACE_MODE_10GBASER)
 		if_mode |= IF_MODE_EN_AUTO;
 
 	if (type == PHY_INTERFACE_MODE_RGMII ||
diff --git a/drivers/net/fsl_enetc.c b/drivers/net/fsl_enetc.c
index 566cdc7e54..12d9942b65 100644
--- a/drivers/net/fsl_enetc.c
+++ b/drivers/net/fsl_enetc.c
@@ -228,7 +228,7 @@ static void enetc_setup_mac_iface(struct udevice *dev,
 		break;
 	case PHY_INTERFACE_MODE_XGMII:
 	case PHY_INTERFACE_MODE_USXGMII:
-	case PHY_INTERFACE_MODE_XFI:
+	case PHY_INTERFACE_MODE_10GBASER:
 		/* set ifmode to (US)XGMII */
 		if_mode = enetc_read_port(priv, ENETC_PM_IF_MODE);
 		if_mode &= ~ENETC_PM_IF_IFMODE_MASK;
@@ -296,7 +296,7 @@ static void enetc_start_pcs(struct udevice *dev)
 		break;
 	case PHY_INTERFACE_MODE_XGMII:
 	case PHY_INTERFACE_MODE_USXGMII:
-	case PHY_INTERFACE_MODE_XFI:
+	case PHY_INTERFACE_MODE_10GBASER:
 		enetc_init_sxgmii(dev);
 		break;
 	};
diff --git a/drivers/net/mscc_eswitch/felix_switch.c b/drivers/net/mscc_eswitch/felix_switch.c
index 859428f7cb..1413084595 100644
--- a/drivers/net/mscc_eswitch/felix_switch.c
+++ b/drivers/net/mscc_eswitch/felix_switch.c
@@ -223,7 +223,7 @@ static void felix_start_pcs(struct udevice *dev, int port,
 		felix_init_sgmii(imdio, port, autoneg);
 		break;
 	case PHY_INTERFACE_MODE_XGMII:
-	case PHY_INTERFACE_MODE_XFI:
+	case PHY_INTERFACE_MODE_10GBASER:
 	case PHY_INTERFACE_MODE_USXGMII:
 		if (felix_init_sxgmii(imdio, port))
 			dev_err(dev, "PCS reset timeout on port %d\n", port);
diff --git a/drivers/net/phy/aquantia.c b/drivers/net/phy/aquantia.c
index d3d35a75d0..66d1d98568 100644
--- a/drivers/net/phy/aquantia.c
+++ b/drivers/net/phy/aquantia.c
@@ -310,7 +310,7 @@ struct {
 					   AQUANTIA_VND1_GSTART_RATE_1G},
 	[PHY_INTERFACE_MODE_SGMII_2500] = {0x144, AQUANTIA_VND1_GSYSCFG_2_5G,
 					   AQUANTIA_VND1_GSTART_RATE_2_5G},
-	[PHY_INTERFACE_MODE_XFI] =        {0x100, AQUANTIA_VND1_GSYSCFG_10G,
+	[PHY_INTERFACE_MODE_10GBASER] =   {0x100, AQUANTIA_VND1_GSYSCFG_10G,
 					   AQUANTIA_VND1_GSTART_RATE_10G},
 	[PHY_INTERFACE_MODE_USXGMII] =    {0x080, AQUANTIA_VND1_GSYSCFG_10G,
 					   AQUANTIA_VND1_GSTART_RATE_10G},
@@ -443,18 +443,18 @@ int aquantia_config(struct phy_device *phydev)
 			return ret;
 	}
 	/*
-	 * for backward compatibility convert XGMII into either XFI or USX based
-	 * on FW config
+	 * for backward compatibility convert XGMII into either 10GBase-R or
+	 * USXGMII based on FW config
 	 */
 	if (interface == PHY_INTERFACE_MODE_XGMII) {
-		debug("use XFI or USXGMII SI protos, XGMII is not valid\n");
+		debug("use 10GBase-R or USXGMII SI protos, XGMII is not valid\n");
 
 		reg_val1 = phy_read(phydev, MDIO_MMD_PHYXS,
 				    AQUANTIA_SYSTEM_INTERFACE_SR);
 		if ((reg_val1 & AQUANTIA_SI_IN_USE_MASK) == AQUANTIA_SI_USXGMII)
 			interface = PHY_INTERFACE_MODE_USXGMII;
 		else
-			interface = PHY_INTERFACE_MODE_XFI;
+			interface = PHY_INTERFACE_MODE_10GBASER;
 	}
 
 	/*
@@ -494,7 +494,7 @@ int aquantia_config(struct phy_device *phydev)
 	case PHY_INTERFACE_MODE_USXGMII:
 		usx_an = 1;
 		/* FALLTHROUGH */
-	case PHY_INTERFACE_MODE_XFI:
+	case PHY_INTERFACE_MODE_10GBASER:
 		/* 10GBASE-T mode */
 		phydev->advertising = SUPPORTED_10000baseT_Full;
 		phydev->supported = phydev->advertising;
@@ -515,7 +515,7 @@ int aquantia_config(struct phy_device *phydev)
 			      phydev->dev->name);
 		} else {
 			reg_val1 &= ~AQUANTIA_USX_AUTONEG_CONTROL_ENA;
-			debug("%s: system interface XFI\n",
+			debug("%s: system interface 10GBase-R\n",
 			      phydev->dev->name);
 		}
 
diff --git a/include/phy.h b/include/phy.h
index 6b928636b6..b9d8dc3a61 100644
--- a/include/phy.h
+++ b/include/phy.h
@@ -368,7 +368,7 @@ static inline int is_10g_interface(phy_interface_t interface)
 {
 	return interface == PHY_INTERFACE_MODE_XGMII ||
 	       interface == PHY_INTERFACE_MODE_USXGMII ||
-	       interface == PHY_INTERFACE_MODE_XFI;
+	       interface == PHY_INTERFACE_MODE_10GBASER;
 }
 
 #endif
diff --git a/include/phy_interface.h b/include/phy_interface.h
index ebb18ecd40..f075abe9c9 100644
--- a/include/phy_interface.h
+++ b/include/phy_interface.h
@@ -37,7 +37,7 @@ typedef enum {
 	PHY_INTERFACE_MODE_CAUI2,
 	PHY_INTERFACE_MODE_CAUI4,
 	PHY_INTERFACE_MODE_NCSI,
-	PHY_INTERFACE_MODE_XFI,
+	PHY_INTERFACE_MODE_10GBASER,
 	PHY_INTERFACE_MODE_USXGMII,
 	PHY_INTERFACE_MODE_NONE,	/* Must be last */
 
@@ -69,7 +69,7 @@ static const char * const phy_interface_strings[] = {
 	[PHY_INTERFACE_MODE_CAUI2]		= "caui2",
 	[PHY_INTERFACE_MODE_CAUI4]		= "caui4",
 	[PHY_INTERFACE_MODE_NCSI]		= "NC-SI",
-	[PHY_INTERFACE_MODE_XFI]		= "xfi",
+	[PHY_INTERFACE_MODE_10GBASER]		= "10gbase-r",
 	[PHY_INTERFACE_MODE_USXGMII]		= "usxgmii",
 	[PHY_INTERFACE_MODE_NONE]		= "",
 };