diff options
author | Stephen Warren <swarren@wwwdotorg.org> | 2016-03-25 07:15:20 +0300 |
---|---|---|
committer | Tom Rini <trini@konsulko.com> | 2016-04-02 00:17:42 +0300 |
commit | f031f501efa898ad1eac641cb27079dd6ded306a (patch) | |
tree | 6b2380a6118b4e2cc1ce51ce3d8c6762040e98f0 | |
parent | 95a2ddaea5575492a780cc7bad4335120542d697 (diff) | |
download | u-boot-f031f501efa898ad1eac641cb27079dd6ded306a.tar.xz |
rpi: BCM2837 and Raspberry Pi 3 32-bit support
The Raspberry Pi 3 contains a BCM2837 SoC. The BCM2837 is a BCM2836 with
the CPU complex swapped out for a quad-core ARMv8. This can operate in 32-
or 64-bit mode. 32-bit mode is the current default selected by the
VideoCore firmware on the Raspberry Pi 3. This patch adds a 32-bit port of
U-Boot for the Raspberry Pi 3.
>From U-Boot's perspective, the only delta between the RPi 2 and RPi 3 is a
change in usage of the SoC UARTs. On all previous Pis, the PL011 was the
only UART in use. The Raspberry Pi 3 adds a Bluetooth module which uses a
UART to connect to the SoC. By default, the PL011 is used for this purpose
since it has larger FIFOs than the other "mini" UART. However, this can
be configured via the VideoCore firmware's config.txt file. This patch
hard-codes use of the mini UART in the RPi 3 port. If your system uses the
PL011 UART for the console even on the RPi 3, please use the RPi 2 U-Boot
port instead. A future change might determine which UART to use at
run-time, thus allowing the RPi 2 and RPi 3 (32-bit) ports to be squashed
together.
The mini UART has some limitations. One externally visible issue in the
BCM2837 integration is that the UART divides the SoC's "core clock" to
generate the baud rate. The core clock is typically variable, and under
control of the VideoCore firmware for thermal management reasons. If the
VC FW does modify the core clock rate, UART communication will be
corrupted since the baud rate will vary from the expected value. This was
not an issue for the PL011 UART, since it is fed by a fixed 3MHz clock. To
work around this, the VideoCore firmware can be told not to modify the SoC
core clock. However, the only way this can happen and be thermally safe is
to limit the core clock to a low/minimum frequency. This leaves
performance on the table for use-cases that don't care about a UART
console. Consequently, use of the mini UART console must be explicitly
requested by entering the following line into config.txt:
enable_uart=1
A recent version of the VC firmware is required to ensure that the mini
UART is fully and correctly initialized by the VC FW; at least
firmware.git 046effa13ebc "firmware: arm_loader: emmc clock depends on
core clock See: https://github.com/raspberrypi/firmware/issues/572".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
-rw-r--r-- | arch/arm/mach-bcm283x/Kconfig | 22 | ||||
-rw-r--r-- | board/raspberrypi/rpi/rpi.c | 16 | ||||
-rw-r--r-- | board/raspberrypi/rpi_3_32b/MAINTAINERS | 6 | ||||
-rw-r--r-- | board/raspberrypi/rpi_3_32b/Makefile | 7 | ||||
-rw-r--r-- | configs/rpi_3_32b_defconfig | 11 | ||||
-rw-r--r-- | include/configs/rpi-common.h | 9 | ||||
-rw-r--r-- | include/configs/rpi_3_32b.h | 15 |
7 files changed, 84 insertions, 2 deletions
diff --git a/arch/arm/mach-bcm283x/Kconfig b/arch/arm/mach-bcm283x/Kconfig index 1f3031d812..a4d291d297 100644 --- a/arch/arm/mach-bcm283x/Kconfig +++ b/arch/arm/mach-bcm283x/Kconfig @@ -6,6 +6,10 @@ config BCM2836 bool "Broadcom BCM2836 SoC support" depends on ARCH_BCM283X +config BCM2837 + bool "Broadcom BCM2837 SoC support" + depends on ARCH_BCM283X + menu "Broadcom BCM283X family" depends on ARCH_BCM283X @@ -50,11 +54,28 @@ config TARGET_RPI_2 select BCM2836 select CPU_V7 +config TARGET_RPI_3_32B + bool "Raspberry Pi 3 32-bit build" + help + Support for all BCM2837-based Raspberry Pi variants, such as + the RPi 3 model B, in AArch32 (32-bit) mode. + + This option assumes the VideoCore firmware is configured to use the + mini UART (rather than PL011) for the serial console. This is the + default on the RPi 3. To enable the UART console, the following non- + default option must be present in config.txt: enable_uart=1. + + This option creates a build targetting the ARMv7/AArch32 ISA. + select ARMV7_LPAE + select BCM2837 + select CPU_V7 + endchoice config SYS_BOARD default "rpi" if TARGET_RPI default "rpi_2" if TARGET_RPI_2 + default "rpi_3_32b" if TARGET_RPI_3_32B config SYS_VENDOR default "raspberrypi" @@ -65,5 +86,6 @@ config SYS_SOC config SYS_CONFIG_NAME default "rpi" if TARGET_RPI default "rpi_2" if TARGET_RPI_2 + default "rpi_3_32b" if TARGET_RPI_3_32B endmenu diff --git a/board/raspberrypi/rpi/rpi.c b/board/raspberrypi/rpi/rpi.c index d31a79c661..20b5cf48f5 100644 --- a/board/raspberrypi/rpi/rpi.c +++ b/board/raspberrypi/rpi/rpi.c @@ -1,5 +1,5 @@ /* - * (C) Copyright 2012-2013,2015 Stephen Warren + * (C) Copyright 2012-2016 Stephen Warren * * SPDX-License-Identifier: GPL-2.0 */ @@ -18,6 +18,7 @@ #include <asm/arch/sdhci.h> #include <asm/global_data.h> #include <dm/platform_data/serial_pl01x.h> +#include <dm/platform_data/serial_bcm283x_mu.h> DECLARE_GLOBAL_DATA_PTR; @@ -30,6 +31,7 @@ U_BOOT_DEVICE(bcm2835_gpios) = { .platdata = &gpio_platdata, }; +#ifdef CONFIG_PL01X_SERIAL static const struct pl01x_serial_platdata serial_platdata = { #ifndef CONFIG_BCM2835 .base = 0x3f201000, @@ -44,6 +46,18 @@ U_BOOT_DEVICE(bcm2835_serials) = { .name = "serial_pl01x", .platdata = &serial_platdata, }; +#else +static const struct bcm283x_mu_serial_platdata serial_platdata = { + .base = 0x3f215040, + .clock = 250000000, + .skip_init = true, +}; + +U_BOOT_DEVICE(bcm2837_serials) = { + .name = "serial_bcm283x_mu", + .platdata = &serial_platdata, +}; +#endif struct msg_get_arm_mem { struct bcm2835_mbox_hdr hdr; diff --git a/board/raspberrypi/rpi_3_32b/MAINTAINERS b/board/raspberrypi/rpi_3_32b/MAINTAINERS new file mode 100644 index 0000000000..bc9df87f03 --- /dev/null +++ b/board/raspberrypi/rpi_3_32b/MAINTAINERS @@ -0,0 +1,6 @@ +RPI_3_32B BOARD +M: Stephen Warren <swarren@wwwdotorg.org> +S: Maintained +F: board/raspberrypi/rpi_3_32b/ +F: include/configs/rpi_3_32b.h +F: configs/rpi_3_32b_defconfig diff --git a/board/raspberrypi/rpi_3_32b/Makefile b/board/raspberrypi/rpi_3_32b/Makefile new file mode 100644 index 0000000000..78e287487c --- /dev/null +++ b/board/raspberrypi/rpi_3_32b/Makefile @@ -0,0 +1,7 @@ +# +# (C) Copyright 2012-2016 Stephen Warren <swarren@wwwdotorg.org> +# +# SPDX-License-Identifier: GPL-2.0 +# + +obj-y := ../rpi/rpi.o diff --git a/configs/rpi_3_32b_defconfig b/configs/rpi_3_32b_defconfig new file mode 100644 index 0000000000..71a0c288c7 --- /dev/null +++ b/configs/rpi_3_32b_defconfig @@ -0,0 +1,11 @@ +CONFIG_ARM=y +CONFIG_ARCH_BCM283X=y +CONFIG_TARGET_RPI_3_32B=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_SYS_PROMPT="U-Boot> " +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_FPGA is not set +CONFIG_CMD_GPIO=y +CONFIG_PHYS_TO_BUS=y +CONFIG_OF_LIBFDT=y diff --git a/include/configs/rpi-common.h b/include/configs/rpi-common.h index 89aee0a85b..5904a3246d 100644 --- a/include/configs/rpi-common.h +++ b/include/configs/rpi-common.h @@ -1,5 +1,5 @@ /* - * (C) Copyright 2012,2015 Stephen Warren + * (C) Copyright 2012-2016 Stephen Warren * * SPDX-License-Identifier: GPL-2.0 */ @@ -24,6 +24,9 @@ * We don't define a machine type for bcm2709/bcm2836 since the RPi Foundation * chose to use someone else's previously registered machine ID (3139, MX51_GGC) * rather than obtaining a valid ID:-/ + * + * For the bcm2837, hopefully a machine type is not needed, since everything + * is DT. */ #ifdef CONFIG_BCM2835 #define CONFIG_MACH_TYPE MACH_TYPE_BCM2708 @@ -94,7 +97,11 @@ #endif /* Console UART */ +#ifdef CONFIG_BCM2837 +#define CONFIG_BCM283X_MU_SERIAL +#else #define CONFIG_PL01X_SERIAL +#endif #define CONFIG_CONS_INDEX 0 #define CONFIG_BAUDRATE 115200 diff --git a/include/configs/rpi_3_32b.h b/include/configs/rpi_3_32b.h new file mode 100644 index 0000000000..c00379b9aa --- /dev/null +++ b/include/configs/rpi_3_32b.h @@ -0,0 +1,15 @@ +/* + * (C) Copyright 2012-2016 Stephen Warren <swarren@wwwdotorg.org> + * + * SPDX-License-Identifier: GPL-2.0 + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SYS_CACHELINE_SIZE 64 + +#include "rpi-common.h" + +#endif |