diff options
author | Mario Six <mario.six@gdsys.cc> | 2018-08-06 11:23:30 +0300 |
---|---|---|
committer | Simon Glass <sjg@chromium.org> | 2018-09-18 09:01:18 +0300 |
commit | e40615565d68465284b3c6a5fc4147f662824a88 (patch) | |
tree | 8654ebc0d143eed7c33e69db4b2a584e44359570 /Documentation/devicetree | |
parent | 0f1caa98807901a2d94cdda891d8380c4dc69063 (diff) | |
download | u-boot-e40615565d68465284b3c6a5fc4147f662824a88.tar.xz |
ram: Add driver for MPC83xx
Add a RAM driver for the MPC83xx architecture.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r-- | Documentation/devicetree/bindings/ram/fsl,mpc83xx-mem-controller.txt | 314 |
1 files changed, 314 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/ram/fsl,mpc83xx-mem-controller.txt b/Documentation/devicetree/bindings/ram/fsl,mpc83xx-mem-controller.txt new file mode 100644 index 0000000000..da01fe908d --- /dev/null +++ b/Documentation/devicetree/bindings/ram/fsl,mpc83xx-mem-controller.txt @@ -0,0 +1,314 @@ +MPC83xx RAM controller + +This driver supplies support for the embedded RAM controller on MCP83xx-series +SoCs. + +For static configuration mode, each controller node should have child nodes +describing the actual RAM modules installed. + +Controller node +=============== + +Required properties: +- compatible: Must be "fsl,mpc83xx-mem-controller" +- reg: The address of the RAM controller's register space +- #address-cells: Must be 2 +- #size-cells: Must be 1 +- driver_software_override: DDR driver software override is enabled (1) or + disabled (0) +- p_impedance_override: DDR driver software p-impedance override; possible + values: + * DSO_P_IMPEDANCE_HIGHEST_Z + * DSO_P_IMPEDANCE_MUCH_HIGHER_Z + * DSO_P_IMPEDANCE_HIGHER_Z + * DSO_P_IMPEDANCE_NOMINAL + * DSO_P_IMPEDANCE_LOWER_Z +- n_impedance_override: DDR driver software n-impedance override; possible + values: + * DSO_N_IMPEDANCE_HIGHEST_Z + * DSO_N_IMPEDANCE_MUCH_HIGHER_Z + * DSO_N_IMPEDANCE_HIGHER_Z + * DSO_N_IMPEDANCE_NOMINAL + * DSO_N_IMPEDANCE_LOWER_Z +- odt_termination_value: ODT termination value for I/Os; possible values: + * ODT_TERMINATION_75_OHM + * ODT_TERMINATION_150_OHM +- ddr_type: Selects voltage level for DDR pads; possible + values: + * DDR_TYPE_DDR2_1_8_VOLT + * DDR_TYPE_DDR1_2_5_VOLT +- mvref_sel: Determine where MVREF_SEL signal is generated; + possible values: + * MVREF_SEL_EXTERNAL + * MVREF_SEL_INTERNAL_GVDD +- m_odr: Disable memory transaction reordering; possible + values: + * M_ODR_ENABLE + * M_ODR_DISABLE +- clock_adjust: Clock adjust; possible values: + * CLOCK_ADJUST_025 + * CLOCK_ADJUST_05 + * CLOCK_ADJUST_075 + * CLOCK_ADJUST_1 +- ext_refresh_rec: Extended refresh recovery time; possible values: + 0, 16, 32, 48, 64, 80, 96, 112 +- read_to_write: Read-to-write turnaround; possible values: + 0, 1, 2, 3 +- write_to_read: Write-to-read turnaround; possible values: + 0, 1, 2, 3 +- read_to_read: Read-to-read turnaround; possible values: + 0, 1, 2, 3 +- write_to_write: Write-to-write turnaround; possible values: + 0, 1, 2, 3 +- active_powerdown_exit: Active powerdown exit timing; possible values: + 1, 2, 3, 4, 5, 6, 7 +- precharge_powerdown_exit: Precharge powerdown exit timing; possible values: + 1, 2, 3, 4, 5, 6, 7 +- odt_powerdown_exit: ODT powerdown exit timing; possible values: + 0, 1, 2, 3, 4, 5, 6, 7, 8, + 9, 10, 11, 12, 13, 14, 15 +- mode_reg_set_cycle: Mode register set cycle time; possible values: + 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 +- precharge_to_activate: Precharge-to-acitvate interval; possible values: + 1, 2, 3, 4, 5, 6, 7 +- activate_to_precharge: Activate to precharge interval; possible values: + 4, 5, 6, 7, 8, 9, 10, 11, 12, + 13, 14, 15, 16, 17, 18, 19 +- activate_to_readwrite: Activate to read/write interval for SDRAM; + possible values: + 1, 2, 3, 4, 5, 6, 7 +- mcas_latency: MCAS latency from READ command; possible values: + * CASLAT_20 + * CASLAT_25 + * CASLAT_30 + * CASLAT_35 + * CASLAT_40 + * CASLAT_45 + * CASLAT_50 + * CASLAT_55 + * CASLAT_60 + * CASLAT_65 + * CASLAT_70 + * CASLAT_75 + * CASLAT_80 +- refresh_recovery: Refresh recovery time; possible values: + 8, 9, 10, 11, 12, 13, 14, 15, + 16, 17, 18, 19, 20, 21, 22, 23 +- last_data_to_precharge: Last data to precharge minimum interval; possible + values: + 1, 2, 3, 4, 5, 6, 7 +- activate_to_activate: Activate-to-activate interval; possible values: + 1, 2, 3, 4, 5, 6, 7 +- last_write_data_to_read: Last write data pair to read command issue + interval; possible values: + 1, 2, 3, 4, 5, 6, 7 +- additive_latency: Additive latency; possible values: + 0, 1, 2, 3, 4, 5 +- mcas_to_preamble_override: MCAS-to-preamble-override; possible values: + * READ_LAT + * READ_LAT_PLUS_1_4 + * READ_LAT_PLUS_1_2 + * READ_LAT_PLUS_3_4 + * READ_LAT_PLUS_1 + * READ_LAT_PLUS_5_4 + * READ_LAT_PLUS_3_2 + * READ_LAT_PLUS_7_4 + * READ_LAT_PLUS_2 + * READ_LAT_PLUS_9_4 + * READ_LAT_PLUS_5_2 + * READ_LAT_PLUS_11_4 + * READ_LAT_PLUS_3 + * READ_LAT_PLUS_13_4 + * READ_LAT_PLUS_7_2 + * READ_LAT_PLUS_15_4 + * READ_LAT_PLUS_4 + * READ_LAT_PLUS_17_4 + * READ_LAT_PLUS_9_2 + * READ_LAT_PLUS_19_4 +- write_latency: Write latency; possible values: + 1, 2, 3, 4, 5, 6, 7 +- read_to_precharge: Read to precharge; possible values: + 1, 2, 3, 4 +- write_cmd_to_write_data: Write command to write data strobe timing + adjustment; possible values: + * CLOCK_DELAY_0 + * CLOCK_DELAY_1_4 + * CLOCK_DELAY_1_2 + * CLOCK_DELAY_3_4 + * CLOCK_DELAY_1 + * CLOCK_DELAY_5_4 + * CLOCK_DELAY_3_2 +- minimum_cke_pulse_width: Minimum CKE pulse width; possible values: + 1, 2, 3, 4 +- four_activates_window: Window for four activates; possible values: + 1, 2, 3, 4 8, 9, 10, 11, 12, + 13, 14, 15, 16, 17, 18, 19 +- self_refresh: Self refresh (during sleep); possible values: + * SREN_DISABLE + * SREN_ENABLE +- ecc: Support for ECC; possible values: + * ECC_DISABLE + * ECC_ENABLE +- registered_dram: Support for registered DRAM; possible values: + * RD_DISABLE + * RD_ENABLE +- sdram_type: Type of SDRAM device to be used; possible values: + * TYPE_DDR1 + * TYPE_DDR2 +- dynamic_power_management: Dynamic power management mode; possible values: + * DYN_PWR_DISABLE + * DYN_PWR_ENABLE +- databus_width: DRAM data bus width; possible values + * DATA_BUS_WIDTH_16 + * DATA_BUS_WIDTH_32 +- nc_auto_precharge: Non-concurrent auto-precharge; possible values: + * NCAP_DISABLE + * NCAP_ENABLE +- timing_2t: 2T timing; possible values: + * TIMING_1T + * TIMING_2T +- bank_interleaving_ctrl: Bank (chip select) interleaving control; possible + values: + * INTERLEAVE_NONE + * INTERLEAVE_1_AND_2 +- precharge_bit_8: Precharge bin 8; possible values + * PRECHARGE_MA_10 + * PRECHARGE_MA_8 +- half_strength: Global half-strength override; possible values: + * STRENGTH_FULL + * STRENGTH_HALF +- bypass_initialization: Bypass initialization; possible values: + * INITIALIZATION_DONT_BYPASS + * INITIALIZATION_BYPASS +- force_self_refresh: Force self refresh; possible values: + * MODE_NORMAL + * MODE_REFRESH +- dll_reset: DLL reset; possible values: + * DLL_RESET_ENABLE + * DLL_RESET_DISABLE +- dqs_config: DQS configuration; possible values: + * DQS_TRUE +- odt_config: ODT configuration; possible values: + * ODT_ASSERT_NEVER + * ODT_ASSERT_WRITES + * ODT_ASSERT_READS + * ODT_ASSERT_ALWAYS +- posted_refreshes: Number of posted refreshes + 1, 2, 3, 4, 5, 6, 7, 8 +- sdmode: Initial value loaded into the DDR SDRAM mode + register +- esdmode: Initial value loaded into the DDR SDRAM extended + mode register +- esdmode2: Initial value loaded into the DDR SDRAM extended + mode 2 register +- esdmode3: Initial value loaded into the DDR SDRAM extended + mode 3 register +- refresh_interval: Refresh interval; possible values: + 0 - 65535 +- precharge_interval: Precharge interval; possible values: + 0 - 16383 + +RAM module node: +================ + +Required properties: +- reg: A triple <cs addr size>, which consists of: + * cs - the chipselect used to drive this RAM module + * addr - the address where this RAM module's memory is map + to in the global memory space + * size - the size of the RAM module's memory in bytes +- auto_precharge: Chip select auto-precharge; possible values: + * AUTO_PRECHARGE_ENABLE + * AUTO_PRECHARGE_DISABLE +- odt_rd_cfg: ODT for reads configuration; possible values: + * ODT_RD_NEVER + * ODT_RD_ONLY_CURRENT + * ODT_RD_ONLY_OTHER_CS + * ODT_RD_ONLY_OTHER_DIMM + * ODT_RD_ALL +- odt_wr_cfg: ODT for writes configuration; possible values: + * ODT_WR_NEVER + * ODT_WR_ONLY_CURRENT + * ODT_WR_ONLY_OTHER_CS + * ODT_WR_ONLY_OTHER_DIMM + * ODT_WR_ALL +- bank_bits: Number of bank bits for SDRAM on chip select; possible + values: + 2, 3 +- row_bits: Number of row bits for SDRAM on chip select; possible values: + 12, 13, 14 +- col_bits: Number of column bits for SDRAM on chip select; possible + values: + 8, 9, 10, 11 + +Example: + +memory@2000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc83xx-mem-controller"; + reg = <0x2000 0x1000>; + device_type = "memory"; + u-boot,dm-pre-reloc; + + driver_software_override = <DSO_ENABLE>; + p_impedance_override = <DSO_P_IMPEDANCE_NOMINAL>; + n_impedance_override = <DSO_N_IMPEDANCE_NOMINAL>; + odt_termination_value = <ODT_TERMINATION_150_OHM>; + ddr_type = <DDR_TYPE_DDR2_1_8_VOLT>; + + clock_adjust = <CLOCK_ADJUST_05>; + + read_to_write = <0>; + write_to_read = <0>; + read_to_read = <0>; + write_to_write = <0>; + active_powerdown_exit = <2>; + precharge_powerdown_exit = <6>; + odt_powerdown_exit = <8>; + mode_reg_set_cycle = <2>; + + precharge_to_activate = <2>; + activate_to_precharge = <6>; + activate_to_readwrite = <2>; + mcas_latency = <CASLAT_40>; + refresh_recovery = <17>; + last_data_to_precharge = <2>; + activate_to_activate = <2>; + last_write_data_to_read = <2>; + + additive_latency = <0>; + mcas_to_preamble_override = <READ_LAT_PLUS_1_2>; + write_latency = <3>; + read_to_precharge = <2>; + write_cmd_to_write_data = <CLOCK_DELAY_1_2>; + minimum_cke_pulse_width = <3>; + four_activates_window = <5>; + + self_refresh = <SREN_ENABLE>; + sdram_type = <TYPE_DDR2>; + databus_width = <DATA_BUS_WIDTH_32>; + + force_self_refresh = <MODE_NORMAL>; + dll_reset = <DLL_RESET_ENABLE>; + dqs_config = <DQS_TRUE>; + odt_config = <ODT_ASSERT_READS>; + posted_refreshes = <1>; + + refresh_interval = <2084>; + precharge_interval = <256>; + + sdmode = <0x0242>; + esdmode = <0x0440>; + + ram@0 { + reg = <0x0 0x0 0x8000000>; + compatible = "nanya,nt5tu64m16hg"; + + odt_rd_cfg = <ODT_RD_NEVER>; + odt_wr_cfg = <ODT_WR_ONLY_CURRENT>; + bank_bits = <3>; + row_bits = <13>; + col_bits = <10>; + }; +}; |