xilinx: Sync DTs with Linux kernel

There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

1 files changed, 35 insertions, 13 deletions

diff --git a/arch/arm/dts/zynqmp-zcu100-revC.dts b/arch/arm/dts/zynqmp-zcu100-revC.dts
index d6c914c917..bbcc69c796 100644
--- a/arch/arm/dts/zynqmp-zcu100-revC.dts
+++ b/arch/arm/dts/zynqmp-zcu100-revC.dts
@@ -69,27 +69,27 @@
 
 	leds {
 		compatible = "gpio-leds";
-		ds2 {
+		led-ds2 {
 			label = "ds2";
 			gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		ds3 {
+		led-ds3 {
 			label = "ds3";
 			gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy0tx"; /* WLAN tx */
 			default-state = "off";
 		};
 
-		ds4 {
+		led-ds4 {
 			label = "ds4";
 			gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy0rx"; /* WLAN rx */
 			default-state = "off";
 		};
 
-		ds5 {
+		led-ds5 {
 			label = "ds5";
 			gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "bluetooth-power";
@@ -130,6 +130,18 @@
 		compatible = "iio-hwmon";
 		io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>;
 	};
+
+	si5335a_0: clk26 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	si5335a_1: clk27 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
 };
 
 &dcc {
@@ -212,7 +224,7 @@
 				compatible = "ti,tps65086";
 				reg = <0x5e>;
 				interrupt-parent = <&gpio>;
-				interrupts = <77 GPIO_ACTIVE_LOW>;
+				interrupts = <77 IRQ_TYPE_LEVEL_LOW>;
 				#gpio-cells = <2>;
 				gpio-controller;
 			};
@@ -250,6 +262,13 @@
 	};
 };
 
+&psgtr {
+	status = "okay";
+	/* usb3, dps */
+	clocks = <&si5335a_0>, <&si5335a_1>;
+	clock-names = "ref0", "ref1";
+};
+
 &rtc {
 	status = "okay";
 };
@@ -281,10 +300,6 @@
 	};
 };
 
-&serdes {
-	status = "okay";
-};
-
 &spi0 { /* Low Speed connector */
 	status = "okay";
 	label = "LS-SPI0";
@@ -318,8 +333,6 @@
 &dwc3_0 {
 	status = "okay";
 	dr_mode = "peripheral";
-	phy-names = "usb3-phy";
-	phys = <&lane2 PHY_TYPE_USB3 0 0 26000000>;
 	maximum-speed = "super-speed";
 };
 
@@ -331,8 +344,6 @@
 &dwc3_1 {
 	status = "okay";
 	dr_mode = "host";
-	phy-names = "usb3-phy";
-	phys = <&lane3 PHY_TYPE_USB3 1 0 26000000>;
 	maximum-speed = "super-speed";
 };
 
@@ -347,3 +358,14 @@
 &ams_ps {
 	status = "okay";
 };
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 1>,
+	       <&psgtr 0 PHY_TYPE_DP 1 1>;
+};