xilinx: Sync DTs with Linux kernel

There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

1 files changed, 48 insertions, 10 deletions

diff --git a/arch/arm/dts/zynqmp-zcu216-revA.dts b/arch/arm/dts/zynqmp-zcu216-revA.dts
index 847e689c15..2302b07c48 100644
--- a/arch/arm/dts/zynqmp-zcu216-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu216-revA.dts
@@ -120,6 +120,20 @@
 		compatible = "iio-hwmon";
 		io-channels = <&dac_avcc 0>, <&dac_avcc 1>, <&dac_avcc 2>, <&dac_avcc 3>;
 	};
+
+	/* 48MHz reference crystal */
+	ref48: ref48M {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+};
+
+&psgtr {
+	status = "okay";
+	/* pcie, sata, usb3, dp */
+	clocks = <&si5341 0 5>, <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+	clock-names = "ref0", "ref1", "ref2", "ref3";
 };
 
 &dcc {
@@ -408,10 +422,41 @@
 			#size-cells = <0>;
 			reg = <1>;
 			si5341: clock-generator@36 { /* SI5341 - u43 */
-				compatible = "si5341";
+				compatible = "silabs,si5341";
 				reg = <0x36>;
+				#clock-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&ref48>;
+				clock-names = "xtal";
+				clock-output-names = "si5341";
+
+				si5341_2: out@2 {
+					/* refclk2 for PS-GT, used for USB3 */
+					reg = <2>;
+					always-on; /* assigned-clocks does not enable, so do it here */
+				};
+				si5341_3: out@3 {
+					/* refclk3 for PS-GT, used for SATA */
+					reg = <3>;
+					always-on; /* assigned-clocks does not enable, so do it here */
+				};
+				si5341_5: out@5 {
+					/* refclk5 PL CLK100 */
+					reg = <5>;
+					always-on; /* assigned-clocks does not enable, so do it here */
+				};
+				si5341_6: out@6 {
+					/* refclk6 PL CLK125 */
+					reg = <6>;
+					always-on; /* assigned-clocks does not enable, so do it here */
+				};
+				si5341_9: out@9 {
+					/* refclk9 used for PS_REF_CLK 33.3 MHz */
+					reg = <9>;
+					always-on; /* assigned-clocks does not enable, so do it here */
+				};
 			};
-
 		};
 		i2c_si570_user_c0: i2c@2 {
 			#address-cells = <1>;
@@ -560,8 +605,7 @@
 	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
 	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
-	phy-names = "sata-phy";
-	phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>;
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
 };
 
 /* SD1 with level shifter */
@@ -575,10 +619,6 @@
 	xlnx,mio-bank = <1>;
 };
 
-&serdes {
-	status = "okay";
-};
-
 &uart0 {
 	status = "okay";
 };
@@ -592,6 +632,4 @@
 	status = "okay";
 	dr_mode = "host";
 	snps,usb3_lpm_capable;
-	phy-names = "usb3-phy";
-	phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
 };