ARM: dts: sun9i: Sync from Linux v5.18-rc1

Copy the devicetree source for the A80 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.

This update should not impact any existing U-Boot functionality.

Signed-off-by: Samuel Holland <samuel@sholland.org>

3 files changed, 212 insertions, 100 deletions

diff --git a/arch/arm/dts/sun9i-a80-cubieboard4.dts b/arch/arm/dts/sun9i-a80-cubieboard4.dts
index 85da85faf8..c8ca8cb7f5 100644
--- a/arch/arm/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/dts/sun9i-a80-cubieboard4.dts
@@ -63,12 +63,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led-0 {
 			label = "cubieboard4:green:usr";
 			gpios = <&pio 7 17 GPIO_ACTIVE_HIGH>; /* PH17 */
 		};
 
-		red {
+		led-1 {
 			label = "cubieboard4:red:usr";
 			gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
 		};
@@ -87,33 +87,25 @@
 	};
 
 	vga-dac {
-		compatible = "corpro,gm7123", "adi,adv7123", "dumb-vga-dac";
+		compatible = "corpro,gm7123", "adi,adv7123";
 		vdd-supply = <&reg_dcdc1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
 			port@0 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				reg = <0>;
 
-				vga_dac_in: endpoint@0 {
-					reg = <0>;
+				vga_dac_in: endpoint {
 					remote-endpoint = <&tcon0_out_vga>;
 				};
 			};
 
 			port@1 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				reg = <1>;
 
-				vga_dac_out: endpoint@0 {
-					reg = <0>;
+				vga_dac_out: endpoint {
 					remote-endpoint = <&vga_con_in>;
 				};
 			};
@@ -133,12 +125,27 @@
 	status = "okay";
 };
 
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_rgmii_pins>;
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_cldo1>;
+	status = "okay";
+};
+
 &i2c3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c3_pins>;
 	status = "okay";
 };
 
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
@@ -183,10 +190,26 @@
 	clocks = <&ac100_rtc 0>;
 };
 
+&pio {
+	vcc-pa-supply = <&reg_ldo_io1>;
+	vcc-pb-supply = <&reg_aldo2>;
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dc1sw>;
+	vcc-pe-supply = <&reg_eldo2>;
+	vcc-pf-supply = <&reg_dcdc1>;
+	vcc-pg-supply = <&reg_ldo_io0>;
+	vcc-ph-supply = <&reg_dcdc1>;
+};
+
 &r_ir {
 	status = "okay";
 };
 
+&r_pio {
+	vcc-pl-supply = <&reg_dldo2>;
+	vcc-pm-supply = <&reg_eldo3>;
+};
+
 &r_rsb {
 	status = "okay";
 
@@ -217,6 +240,10 @@
 				/* unused */
 			};
 
+			reg_dc1sw: dc1sw {
+				regulator-name = "vcc-pd";
+			};
+
 			reg_dc5ldo: dc5ldo {
 				regulator-always-on;
 				regulator-min-microvolt = <800000>;
@@ -271,7 +298,6 @@
 			};
 
 			reg_dldo2: dldo2 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pl";
@@ -290,14 +316,12 @@
 			};
 
 			reg_eldo3: eldo3 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pm-codec-io1";
 			};
 
 			reg_ldo_io0: ldo_io0 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pg";
@@ -385,6 +409,14 @@
 				 */
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
+				/*
+				 * The PHY requires 20ms after all voltages
+				 * are applied until core logic is ready and
+				 * 30ms after the reset pin is de-asserted.
+				 * Set a 100ms delay to account for PMIC
+				 * ramp time and board traces.
+				 */
+				regulator-enable-ramp-delay = <100000>;
 				regulator-name = "vcc-gmac-phy";
 			};
 
@@ -464,8 +496,7 @@
 };
 
 &tcon0_out {
-	tcon0_out_vga: endpoint@0 {
-		reg = <0>;
+	tcon0_out_vga: endpoint {
 		remote-endpoint = <&vga_dac_in>;
 	};
 };
diff --git a/arch/arm/dts/sun9i-a80-optimus.dts b/arch/arm/dts/sun9i-a80-optimus.dts
index 58a199b0e4..5c3580d712 100644
--- a/arch/arm/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/dts/sun9i-a80-optimus.dts
@@ -82,7 +82,7 @@
 
 	reg_usb1_vbus: usb1-vbus {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
+		regulator-name = "usb1-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
@@ -91,7 +91,7 @@
 
 	reg_usb3_vbus: usb3-vbus {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
+		regulator-name = "usb3-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 		enable-active-high;
@@ -120,6 +120,21 @@
 	status = "okay";
 };
 
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_rgmii_pins>;
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_cldo1>;
+	status = "okay";
+};
+
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
@@ -172,10 +187,26 @@
 	clocks = <&ac100_rtc 0>;
 };
 
+&pio {
+	vcc-pa-supply = <&reg_ldo_io1>;
+	vcc-pb-supply = <&reg_aldo2>;
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dcdc1>;
+	vcc-pe-supply = <&reg_eldo2>;
+	vcc-pf-supply = <&reg_dcdc1>;
+	vcc-pg-supply = <&reg_ldo_io0>;
+	vcc-ph-supply = <&reg_dcdc1>;
+};
+
 &r_ir {
 	status = "okay";
 };
 
+&r_pio {
+	vcc-pl-supply = <&reg_dldo2>;
+	vcc-pm-supply = <&reg_eldo3>;
+};
+
 &r_rsb {
 	status = "okay";
 
@@ -213,6 +244,10 @@
 				regulator-name = "vdd-cpus-09-usbh";
 			};
 
+			dc1sw {
+				/* unused */
+			};
+
 			reg_dcdc1: dcdc1 {
 				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
@@ -260,7 +295,6 @@
 			};
 
 			reg_dldo2: dldo2 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pl";
@@ -279,14 +313,12 @@
 			};
 
 			reg_eldo3: eldo3 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pm-codec-io1";
 			};
 
 			reg_ldo_io0: ldo_io0 {
-				regulator-always-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-name = "vcc-pg";
@@ -374,6 +406,14 @@
 				 */
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
+				/*
+				 * The PHY requires 20ms after all voltages
+				 * are applied until core logic is ready and
+				 * 30ms after the reset pin is de-asserted.
+				 * Set a 100ms delay to account for PMIC
+				 * ramp time and board traces.
+				 */
+				regulator-enable-ramp-delay = <100000>;
 				regulator-name = "vcc-gmac-phy";
 			};
 
diff --git a/arch/arm/dts/sun9i-a80.dtsi b/arch/arm/dts/sun9i-a80.dtsi
index 25591d6883..ce4fa6706d 100644
--- a/arch/arm/dts/sun9i-a80.dtsi
+++ b/arch/arm/dts/sun9i-a80.dtsi
@@ -56,6 +56,10 @@
 	#size-cells = <2>;
 	interrupt-parent = <&gic>;
 
+	aliases {
+		ethernet0 = &gmac;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -183,6 +187,37 @@
 			clock-output-names = "osc32k";
 		};
 
+		/*
+		 * The following two are dummy clocks, placeholders
+		 * used in the gmac_tx clock. The gmac driver will
+		 * choose one parent depending on the PHY interface
+		 * mode, using clk_set_rate auto-reparenting.
+		 *
+		 * The actual TX clock rate is not controlled by the
+		 * gmac_tx clock.
+		 */
+		mii_phy_tx_clk: mii_phy_tx_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+			clock-output-names = "mii_phy_tx";
+		};
+
+		gmac_int_tx_clk: gmac_int_tx_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <125000000>;
+			clock-output-names = "gmac_int_tx";
+		};
+
+		gmac_tx_clk: clk@800030 {
+			#clock-cells = <0>;
+			compatible = "allwinner,sun7i-a20-gmac-clk";
+			reg = <0x00800030 0x4>;
+			clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>;
+			clock-output-names = "gmac_tx";
+		};
+
 		cpus_clk: clk@8001410 {
 			compatible = "allwinner,sun9i-a80-cpus-clk";
 			reg = <0x08001410 0x4>;
@@ -254,7 +289,7 @@
 		status = "disabled";
 	};
 
-	soc {
+	soc@20000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -283,6 +318,27 @@
 			};
 		};
 
+		gmac: ethernet@830000 {
+			compatible = "allwinner,sun7i-a20-gmac";
+			reg = <0x00830000 0x1054>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks = <&ccu CLK_BUS_GMAC>, <&gmac_tx_clk>;
+			clock-names = "stmmaceth", "allwinner_gmac_tx";
+			resets = <&ccu RST_BUS_GMAC>;
+			reset-names = "stmmaceth";
+			snps,pbl = <2>;
+			snps,fixed-burst;
+			snps,force_sf_dma_mode;
+			status = "disabled";
+
+			mdio: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		ehci0: usb@a00000 {
 			compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
 			reg = <0x00a00000 0x100>;
@@ -331,16 +387,16 @@
 		usbphy2: phy@a01800 {
 			compatible = "allwinner,sun9i-a80-usb-phy";
 			reg = <0x00a01800 0x4>;
-			clocks = <&usb_clocks CLK_USB1_HSIC>,
+			clocks = <&usb_clocks CLK_USB1_PHY>,
 				 <&usb_clocks CLK_USB_HSIC>,
-				 <&usb_clocks CLK_USB1_PHY>;
-			clock-names = "hsic_480M",
+				 <&usb_clocks CLK_USB1_HSIC>;
+			clock-names = "phy",
 				      "hsic_12M",
-				      "phy";
-			resets = <&usb_clocks RST_USB1_HSIC>,
-				 <&usb_clocks RST_USB1_PHY>;
-			reset-names = "hsic",
-				      "phy";
+				      "hsic_480M";
+			resets = <&usb_clocks RST_USB1_PHY>,
+				 <&usb_clocks RST_USB1_HSIC>;
+			reset-names = "phy",
+				      "hsic";
 			status = "disabled";
 			#phy-cells = <0>;
 			/* usb1 is always used with HSIC */
@@ -373,16 +429,16 @@
 		usbphy3: phy@a02800 {
 			compatible = "allwinner,sun9i-a80-usb-phy";
 			reg = <0x00a02800 0x4>;
-			clocks = <&usb_clocks CLK_USB2_HSIC>,
+			clocks = <&usb_clocks CLK_USB2_PHY>,
 				 <&usb_clocks CLK_USB_HSIC>,
-				 <&usb_clocks CLK_USB2_PHY>;
-			clock-names = "hsic_480M",
+				 <&usb_clocks CLK_USB2_HSIC>;
+			clock-names = "phy",
 				      "hsic_12M",
-				      "phy";
-			resets = <&usb_clocks RST_USB2_HSIC>,
-				 <&usb_clocks RST_USB2_PHY>;
-			reset-names = "hsic",
-				      "phy";
+				      "hsic_480M";
+			resets = <&usb_clocks RST_USB2_PHY>,
+				 <&usb_clocks RST_USB2_HSIC>;
+			reset-names = "phy",
+				      "hsic";
 			status = "disabled";
 			#phy-cells = <0>;
 		};
@@ -401,6 +457,15 @@
 			reg = <0x01700000 0x100>;
 		};
 
+		crypto: crypto@1c02000 {
+			compatible = "allwinner,sun9i-a80-crypto";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&ccu RST_BUS_SS>;
+			clocks = <&ccu CLK_BUS_SS>, <&ccu CLK_SS>;
+			clock-names = "bus", "mod";
+		};
+
 		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun9i-a80-mmc";
 			reg = <0x01c0f000 0x1000>;
@@ -465,9 +530,7 @@
 			compatible = "allwinner,sun9i-a80-mmc-config-clk";
 			reg = <0x01c13000 0x10>;
 			clocks = <&ccu CLK_BUS_MMC>;
-			clock-names = "ahb";
 			resets = <&ccu RST_BUS_MMC>;
-			reset-names = "ahb";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			clock-output-names = "mmc0_config", "mmc1_config",
@@ -475,7 +538,7 @@
 		};
 
 		gic: interrupt-controller@1c41000 {
-			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			compatible = "arm,gic-400";
 			reg = <0x01c41000 0x1000>,
 			      <0x01c42000 0x2000>,
 			      <0x01c44000 0x2000>,
@@ -544,12 +607,9 @@
 				#size-cells = <0>;
 
 				fe0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					fe0_out_deu0: endpoint@0 {
-						reg = <0>;
+					fe0_out_deu0: endpoint {
 						remote-endpoint = <&deu0_in_fe0>;
 					};
 				};
@@ -571,12 +631,9 @@
 				#size-cells = <0>;
 
 				fe1_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					fe1_out_deu1: endpoint@0 {
-						reg = <0>;
+					fe1_out_deu1: endpoint {
 						remote-endpoint = <&deu1_in_fe1>;
 					};
 				};
@@ -614,12 +671,9 @@
 				};
 
 				be0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					be0_out_drc0: endpoint@0 {
-						reg = <0>;
+					be0_out_drc0: endpoint {
 						remote-endpoint = <&drc0_in_be0>;
 					};
 				};
@@ -657,12 +711,9 @@
 				};
 
 				be1_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					be1_out_drc1: endpoint@0 {
-						reg = <0>;
+					be1_out_drc1: endpoint {
 						remote-endpoint = <&drc1_in_be1>;
 					};
 				};
@@ -686,12 +737,9 @@
 				#size-cells = <0>;
 
 				deu0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					deu0_in_fe0: endpoint@0 {
-						reg = <0>;
+					deu0_in_fe0: endpoint {
 						remote-endpoint = <&fe0_out_deu0>;
 					};
 				};
@@ -731,12 +779,9 @@
 				#size-cells = <0>;
 
 				deu1_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					deu1_in_fe1: endpoint@0 {
-						reg = <0>;
+					deu1_in_fe1: endpoint {
 						remote-endpoint = <&fe1_out_deu1>;
 					};
 				};
@@ -776,23 +821,17 @@
 				#size-cells = <0>;
 
 				drc0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					drc0_in_be0: endpoint@0 {
-						reg = <0>;
+					drc0_in_be0: endpoint {
 						remote-endpoint = <&be0_out_drc0>;
 					};
 				};
 
 				drc0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					drc0_out_tcon0: endpoint@0 {
-						reg = <0>;
+					drc0_out_tcon0: endpoint {
 						remote-endpoint = <&tcon0_in_drc0>;
 					};
 				};
@@ -816,23 +855,17 @@
 				#size-cells = <0>;
 
 				drc1_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					drc1_in_be1: endpoint@0 {
-						reg = <0>;
+					drc1_in_be1: endpoint {
 						remote-endpoint = <&be1_out_drc1>;
 					};
 				};
 
 				drc1_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 
-					drc1_out_tcon1: endpoint@0 {
-						reg = <0>;
+					drc1_out_tcon1: endpoint {
 						remote-endpoint = <&tcon1_in_drc1>;
 					};
 				};
@@ -845,28 +878,28 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_LCD0>, <&ccu CLK_LCD0>;
 			clock-names = "ahb", "tcon-ch0";
-			resets = <&ccu RST_BUS_LCD0>, <&ccu RST_BUS_EDP>;
-			reset-names = "lcd", "edp";
+			resets = <&ccu RST_BUS_LCD0>,
+				 <&ccu RST_BUS_EDP>,
+				 <&ccu RST_BUS_LVDS>;
+			reset-names = "lcd",
+				      "edp",
+				      "lvds";
 			clock-output-names = "tcon0-pixel-clock";
+			#clock-cells = <0>;
 
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
 				tcon0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					tcon0_in_drc0: endpoint@0 {
-						reg = <0>;
+					tcon0_in_drc0: endpoint {
 						remote-endpoint = <&drc0_out_tcon0>;
 					};
 				};
 
 				tcon0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 				};
 			};
@@ -886,19 +919,14 @@
 				#size-cells = <0>;
 
 				tcon1_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <0>;
 
-					tcon1_in_drc1: endpoint@0 {
-						reg = <0>;
+					tcon1_in_drc1: endpoint {
 						remote-endpoint = <&drc1_out_tcon1>;
 					};
 				};
 
 				tcon1_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
 					reg = <1>;
 				};
 			};
@@ -930,6 +958,7 @@
 			compatible = "allwinner,sun6i-a31-wdt";
 			reg = <0x06000ca0 0x20>;
 			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
 		};
 
 		pio: pinctrl@6000800 {
@@ -945,9 +974,20 @@
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
-			#size-cells = <0>;
 			#gpio-cells = <3>;
 
+			gmac_rgmii_pins: gmac-rgmii-pins {
+				pins = "PA0", "PA1", "PA2", "PA3", "PA4", "PA5",
+				       "PA7", "PA8", "PA9", "PA10", "PA12",
+				       "PA13", "PA15", "PA16", "PA17";
+				function = "gmac";
+				/*
+				 * data lines in RGMII mode use DDR mode
+				 * and need a higher signal drive strength
+				 */
+				drive-strength = <40>;
+			};
+
 			i2c3_pins: i2c3-pins {
 				pins = "PG10", "PG11";
 				function = "i2c3";
@@ -1126,6 +1166,7 @@
 			compatible = "allwinner,sun6i-a31-wdt";
 			reg = <0x08001000 0x20>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
 		};
 
 		prcm@8001400 {
@@ -1148,7 +1189,7 @@
 		};
 
 		r_ir: ir@8002000 {
-			compatible = "allwinner,sun5i-a13-ir";
+			compatible = "allwinner,sun6i-a31-ir";
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&r_ir_pins>;
@@ -1196,7 +1237,7 @@
 			};
 		};
 
-		r_rsb: i2c@8003400 {
+		r_rsb: rsb@8003400 {
 			compatible = "allwinner,sun8i-a23-rsb";
 			reg = <0x08003400 0x400>;
 			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;