powerpc: ppc4xx: remove csb272, csb472 support

These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tolunay Orkun <torkun@nextio.com>

1 files changed, 0 insertions, 196 deletions

diff --git a/board/csb272/init.S b/board/csb272/init.S
deleted file mode 100644
index bf1d98680d..0000000000
--- a/board/csb272/init.S
+++ /dev/null
@@ -1,196 +0,0 @@
-/*
- * SPDX-License-Identifier:	GPL-2.0	IBM-pibs
- */
-#include <config.h>
-#include <asm/ppc4xx.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#include <asm/cache.h>
-#include <asm/mmu.h>
-
-#define LI32(reg,val) \
-	addis   reg,0,val@h;\
-	ori     reg,reg,val@l
-
-#define WDCR_EBC(reg,val) \
-	addi    r4,0,reg;\
-	mtdcr   EBC0_CFGADDR,r4;\
-	addis   r4,0,val@h;\
-	ori     r4,r4,val@l;\
-	mtdcr   EBC0_CFGDATA,r4
-
-#define WDCR_SDRAM(reg,val) \
-	addi    r4,0,reg;\
-	mtdcr   SDRAM0_CFGADDR,r4;\
-	addis   r4,0,val@h;\
-	ori     r4,r4,val@l;\
-	mtdcr   SDRAM0_CFGDATA,r4
-
-/******************************************************************************
- * Function:	ext_bus_cntlr_init
- *
- * Description:	Configures EBC Controller and a few basic chip selects.
- *
- *		CS0 is setup to get the Boot Flash out of the addresss range
- *		so that we may setup a stack.  CS7 is setup so that we can
- *		access and reset the hardware watchdog.
- *
- *		IMPORTANT: For pass1 this code must run from
- *		cache since you can not reliably change a peripheral banks
- *		timing register (pbxap) while running code from that bank.
- *		For ex., since we are running from ROM on bank 0, we can NOT
- *		execute the code that modifies bank 0 timings from ROM, so
- *		we run it from cache.
- *
- * Notes:	Does NOT use the stack.
- *****************************************************************************/
-	.section ".text"
-	.align	2
-	.globl	ext_bus_cntlr_init
-	.type	ext_bus_cntlr_init, @function
-ext_bus_cntlr_init:
-	mflr	r0
-	/********************************************************************
-	 * Prefetch entire ext_bus_cntrl_init function into the icache.
-	 * This is necessary because we are going to change the same CS we
-	 * are executing from.  Otherwise a CPU lockup may occur.
-	 *******************************************************************/
-	bl	..getAddr
-..getAddr:
-	mflr	r3			/* get address of ..getAddr */
-
-	/* Calculate number of cache lines for this function */
-	addi	r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2)
-	mtctr	r4
-..ebcloop:
-	icbt	r0, r3			/* prefetch cache line for addr in r3*/
-	addi	r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */
-	bdnz	..ebcloop		/* continue for $CTR cache lines */
-
-	/********************************************************************
-	 * Delay to ensure all accesses to ROM are complete before changing
-	 * bank 0 timings. 200usec should be enough.
-	 * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles.
-	 *******************************************************************/
-	addis	r3, 0, 0x0
-	ori	r3, r3, 0xA000		/* wait 200us from reset */
-	mtctr	r3
-..spinlp:
-	bdnz	..spinlp		/* spin loop */
-
-	/********************************************************************
-	 * SETUP CPC0_CR0
-	 *******************************************************************/
-	LI32(r4, 0x007000c0)
-	mtdcr	CPC0_CR0, r4
-
-	/********************************************************************
-	 * Setup CPC0_CR1: Change PCIINT signal to PerWE
-	 *******************************************************************/
-	mfdcr	r4, CPC0_CR1
-	ori	r4, r4, 0x4000
-	mtdcr	CPC0_CR1, r4
-
-	/********************************************************************
-	 * Setup External Bus Controller (EBC).
-	 *******************************************************************/
-	WDCR_EBC(EBC0_CFG, 0xd84c0000)
-	/********************************************************************
-	 * Memory Bank 0 (Intel 28F128J3 Flash) initialization
-	 *******************************************************************/
-	/*WDCR_EBC(PB1AP, 0x02869200)*/
-	WDCR_EBC(PB1AP, 0x07869200)
-	WDCR_EBC(PB0CR, 0xfe0bc000)
-	/********************************************************************
-	 * Memory Bank 1 (Holtek HT6542B PS/2) initialization
-	 *******************************************************************/
-	WDCR_EBC(PB1AP, 0x1f869200)
-	WDCR_EBC(PB1CR, 0xf0818000)
-	/********************************************************************
-	 * Memory Bank 2 (Epson S1D13506) initialization
-	 *******************************************************************/
-	WDCR_EBC(PB2AP, 0x05860300)
-	WDCR_EBC(PB2CR, 0xf045a000)
-	/********************************************************************
-	 * Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization
-	 *******************************************************************/
-	WDCR_EBC(PB3AP, 0x0387d200)
-	WDCR_EBC(PB3CR, 0xf021c000)
-	/********************************************************************
-	 * Memory Bank 4-7 (Unused) initialization
-	 *******************************************************************/
-	WDCR_EBC(PB4AP, 0)
-	WDCR_EBC(PB4CR, 0)
-	WDCR_EBC(PB5AP, 0)
-	WDCR_EBC(PB5CR, 0)
-	WDCR_EBC(PB6AP, 0)
-	WDCR_EBC(PB6CR, 0)
-	WDCR_EBC(PB7AP, 0)
-	WDCR_EBC(PB7CR, 0)
-
-	/* We are all done */
-	mtlr	r0			/* Restore link register */
-	blr				/* Return to calling function */
-.Lfe0:	.size	ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init
-/* end ext_bus_cntlr_init() */
-
-/******************************************************************************
- * Function:	sdram_init
- *
- * Description:	Configures SDRAM memory banks.
- *
- * Notes:	Does NOT use the stack.
- *****************************************************************************/
-	.section ".text"
-	.align	2
-	.globl	sdram_init
-	.type	sdram_init, @function
-sdram_init:
-
-	/*
-	 * Disable memory controller to allow
-	 * values to be changed.
-	 */
-	WDCR_SDRAM(SDRAM0_CFG, 0x00000000)
-
-	/*
-	 * Configure Memory Banks
-	 */
-	WDCR_SDRAM(SDRAM0_B0CR, 0x00084001)
-	WDCR_SDRAM(SDRAM0_B1CR, 0x00000000)
-	WDCR_SDRAM(SDRAM0_B2CR, 0x00000000)
-	WDCR_SDRAM(SDRAM0_B3CR, 0x00000000)
-
-	/*
-	 * Set up SDTR1 (SDRAM Timing Register)
-	 */
-	WDCR_SDRAM(SDRAM0_TR, 0x00854009)
-
-	/*
-	 * Set RTR (Refresh Timing Register)
-	 */
-	WDCR_SDRAM(SDRAM0_RTR,   0x10000000)
-	/* WDCR_SDRAM(SDRAM0_RTR,   0x05f00000) */
-
-	/********************************************************************
-	 * Delay to ensure 200usec have elapsed since reset. Assume worst
-	 * case that the core is running 200Mhz:
-	 *	  200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
-	 *******************************************************************/
-	addis   r3, 0, 0x0000
-	ori     r3, r3, 0xA000		/* Wait >200us from reset */
-	mtctr   r3
-..spinlp2:
-	bdnz    ..spinlp2		/* spin loop */
-
-	/********************************************************************
-	 * Set memory controller options reg, MCOPT1.
-	 *******************************************************************/
-	WDCR_SDRAM(SDRAM0_CFG,0x80800000)
-
-..sdri_done:
-	blr				/* Return to calling function */
-.Lfe1:	.size	sdram_init,.Lfe1-sdram_init
-/* end sdram_init() */