net: tsec: Remove non-DM_ETH support code

As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code.  Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.

Signed-off-by: Tom Rini <trini@konsulko.com>

1 files changed, 0 insertions, 73 deletions

diff --git a/board/freescale/common/pixis.c b/board/freescale/common/pixis.c
index 6fdb11039e..cb9f454972 100644
--- a/board/freescale/common/pixis.c
+++ b/board/freescale/common/pixis.c
@@ -281,79 +281,6 @@ U_BOOT_CMD(
 	""
 );
 
-#ifdef CONFIG_PIXIS_SGMII_CMD
-
-/* Enable or disable SGMII mode for a TSEC
- */
-static int pixis_set_sgmii(struct cmd_tbl *cmdtp, int flag, int argc,
-			   char *const argv[])
-{
-	int which_tsec = -1;
-	unsigned char mask;
-	unsigned char switch_mask;
-
-	if ((argc > 2) && (strcmp(argv[1], "all") != 0))
-		which_tsec = simple_strtoul(argv[1], NULL, 0);
-
-	switch (which_tsec) {
-#ifdef CONFIG_TSEC1
-	case 1:
-		mask = PIXIS_VSPEED2_TSEC1SER;
-		switch_mask = PIXIS_VCFGEN1_TSEC1SER;
-		break;
-#endif
-#ifdef CONFIG_TSEC2
-	case 2:
-		mask = PIXIS_VSPEED2_TSEC2SER;
-		switch_mask = PIXIS_VCFGEN1_TSEC2SER;
-		break;
-#endif
-#ifdef CONFIG_TSEC3
-	case 3:
-		mask = PIXIS_VSPEED2_TSEC3SER;
-		switch_mask = PIXIS_VCFGEN1_TSEC3SER;
-		break;
-#endif
-#ifdef CONFIG_TSEC4
-	case 4:
-		mask = PIXIS_VSPEED2_TSEC4SER;
-		switch_mask = PIXIS_VCFGEN1_TSEC4SER;
-		break;
-#endif
-	default:
-		mask = PIXIS_VSPEED2_MASK;
-		switch_mask = PIXIS_VCFGEN1_MASK;
-		break;
-	}
-
-	/* Toggle whether the switches or FPGA control the settings */
-	if (!strcmp(argv[argc - 1], "switch"))
-		clrbits_8(pixis_base + PIXIS_VCFGEN1, switch_mask);
-	else
-		setbits_8(pixis_base + PIXIS_VCFGEN1, switch_mask);
-
-	/* If it's not the switches, enable or disable SGMII, as specified */
-	if (!strcmp(argv[argc - 1], "on"))
-		clrbits_8(pixis_base + PIXIS_VSPEED2, mask);
-	else if (!strcmp(argv[argc - 1], "off"))
-		setbits_8(pixis_base + PIXIS_VSPEED2, mask);
-
-	return 0;
-}
-
-U_BOOT_CMD(
-	pixis_set_sgmii, CONFIG_SYS_MAXARGS, 1, pixis_set_sgmii,
-	"pixis_set_sgmii"
-	" - Enable or disable SGMII mode for a given TSEC \n",
-	"\npixis_set_sgmii [TSEC num] <on|off|switch>\n"
-	"    TSEC num: 1,2,3,4 or 'all'.  'all' is default.\n"
-	"    on - enables SGMII\n"
-	"    off - disables SGMII\n"
-	"    switch - use switch settings"
-);
-
-#endif
-
 /*
  * This function takes the non-integral cpu:mpx pll ratio
  * and converts it to an integer that can be used to assign