Makefile: Rename u-boot-spl.kwb to u-boot-with-spl.kwb

File name with pattern u-boot-spl* is used on all places except in kwb
image for binary with SPL-only code. Combined binary with both SPL and
proper U-Boot in other places has file name pattern u-boot-with-spl*.

Make it consistent also for kwb image and rename u-boot-spl.kwb to
u-boot-with-spl.kwb as this image contains both SPL and proper U-Boot code.

Also update documentation about file name changes.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>

3 files changed, 10 insertions, 10 deletions

diff --git a/board/Marvell/db-88f6820-gp/README b/board/Marvell/db-88f6820-gp/README
index 9bea5b35cb..b4db6ed625 100644
--- a/board/Marvell/db-88f6820-gp/README
+++ b/board/Marvell/db-88f6820-gp/README
@@ -2,17 +2,17 @@ Update from original Marvell U-Boot to mainline U-Boot:
 -------------------------------------------------------
 
 The resulting image including the SPL binary with the
-full DDR setup is "u-boot-spl.kwb".
+full DDR setup is "u-boot-with-spl.kwb".
 
 To update the SPI NOR flash, please use the following
 command:
 
-=> sf probe;tftpboot 2000000 db-88f6820-gp/u-boot-spl.kwb;\
+=> sf probe;tftpboot 2000000 db-88f6820-gp/u-boot-with-spl.kwb;\
 sf update 2000000 0 60000
 
 Note that the original Marvell U-Boot seems to have
 problems with the "sf update" command. This does not
 work reliable. So here this command should be used:
 
-=> sf probe;tftpboot 2000000 db-88f6820-gp/u-boot-spl.kwb;\
+=> sf probe;tftpboot 2000000 db-88f6820-gp/u-boot-with-spl.kwb;\
 sf erase 0 60000;sf write 2000000 0 60000
diff --git a/board/kobol/helios4/README b/board/kobol/helios4/README
index 749f048278..d615cdd264 100644
--- a/board/kobol/helios4/README
+++ b/board/kobol/helios4/README
@@ -7,12 +7,12 @@ $ make helios4_defconfig
 $ make
 
 The resulting image including the SPL binary with the
-full DDR setup is "u-boot-spl.kwb".
+full DDR setup is "u-boot-with-spl.kwb".
 
 Now all you need to do is copy this image on a SD card.
 For example with this command:
 
-$ sudo dd if=u-boot-spl.kwb of=/dev/sdX bs=512 seek=1
+$ sudo dd if=u-boot-with-spl.kwb of=/dev/sdX bs=512 seek=1
 
 Please use the correct device node for your setup instead
 of "/dev/sdX" here!
@@ -38,7 +38,7 @@ Set the SW1 DIP switches to UART boot (see above).
 
 Run the following command to initiate U-Boot download:
 
-  ./tools/kwboot -p -b u-boot-spl.kwb /dev/ttyUSBX
+  ./tools/kwboot -p -b u-boot-with-spl.kwb /dev/ttyUSBX
 
 Use the correct UART device node for /dev/ttyUSBX.
 
diff --git a/board/solidrun/clearfog/README b/board/solidrun/clearfog/README
index 9375be8495..ed4a712c5a 100644
--- a/board/solidrun/clearfog/README
+++ b/board/solidrun/clearfog/README
@@ -7,12 +7,12 @@ $ make clearfog_defconfig
 $ make
 
 The resulting image including the SPL binary with the
-full DDR setup is "u-boot-spl.kwb".
+full DDR setup is "u-boot-with-spl.kwb".
 
 Now all you need to do is copy this image on a SD card.
 For example with this command:
 
-$ sudo dd if=u-boot-spl.kwb of=/dev/sdX bs=512 seek=1
+$ sudo dd if=u-boot-with-spl.kwb of=/dev/sdX bs=512 seek=1
 
 Please use the correct device node for your setup instead
 of "/dev/sdX" here!
@@ -29,7 +29,7 @@ command:
 Install U-Boot on eMMC boot partition from Linux running on Clearfog:
 
   echo 0 > /sys/block/mmcblk0boot0/force_ro
-  dd if=u-boot-spl.kwb of=/dev/mmcblk0boot0
+  dd if=u-boot-with-spl.kwb of=/dev/mmcblk0boot0
 
 Note that the SD card is not accessible when the Clearfog SOM has eMMC.
 Consider initial boot from UART (see below).
@@ -66,7 +66,7 @@ Set the SW1 DIP switches to UART boot (see above).
 
 Run the following command to initiate U-Boot download:
 
-  ./tools/kwboot -b u-boot-spl.kwb /dev/ttyUSBX
+  ./tools/kwboot -b u-boot-with-spl.kwb /dev/ttyUSBX
 
 Use the correct UART device node for /dev/ttyUSBX.