diff options
author | Kishon Vijay Abraham I <kishon@ti.com> | 2018-01-30 18:01:32 +0300 |
---|---|---|
committer | Jaehoon Chung <jh80.chung@samsung.com> | 2018-02-19 10:58:54 +0300 |
commit | b59448170934094570a497ff7c5b4b2e94cff5a2 (patch) | |
tree | 4bc713080efeceb587d93d685b2af83815915e83 /drivers/mmc | |
parent | 48a2f11443a1f15c1dcee4f2051f12edc6378510 (diff) | |
download | u-boot-b59448170934094570a497ff7c5b4b2e94cff5a2.tar.xz |
mmc: omap_hsmmc: add support to set default io voltage
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Diffstat (limited to 'drivers/mmc')
-rw-r--r-- | drivers/mmc/omap_hsmmc.c | 67 |
1 files changed, 67 insertions, 0 deletions
diff --git a/drivers/mmc/omap_hsmmc.c b/drivers/mmc/omap_hsmmc.c index 713faab110..5141bf66e1 100644 --- a/drivers/mmc/omap_hsmmc.c +++ b/drivers/mmc/omap_hsmmc.c @@ -74,6 +74,9 @@ struct omap_hsmmc_data { int wp_gpio; #endif #endif +#if CONFIG_IS_ENABLED(DM_MMC) + uint iov; +#endif u8 controller_flags; #ifndef CONFIG_OMAP34XX struct omap_hsmmc_adma_desc *adma_desc_table; @@ -111,6 +114,8 @@ struct omap_hsmmc_adma_desc { * that the bandwidth is always above 3MB/s). */ #define DMA_TIMEOUT_PER_MB 333 +#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0) +#define OMAP_HSMMC_NO_1_8_V BIT(1) #define OMAP_HSMMC_USE_ADMA BIT(2) static int mmc_read_data(struct hsmmc *mmc_base, char *buf, unsigned int size); @@ -252,6 +257,58 @@ void mmc_init_stream(struct hsmmc *mmc_base) writel(readl(&mmc_base->con) & ~INIT_INITSTREAM, &mmc_base->con); } +#if CONFIG_IS_ENABLED(DM_MMC) +static void omap_hsmmc_conf_bus_power(struct mmc *mmc) +{ + struct hsmmc *mmc_base; + struct omap_hsmmc_data *priv = omap_hsmmc_get_data(mmc); + u32 val; + + mmc_base = priv->base_addr; + + val = readl(&mmc_base->hctl) & ~SDVS_MASK; + + switch (priv->iov) { + case IOV_3V3: + val |= SDVS_3V3; + break; + case IOV_3V0: + val |= SDVS_3V0; + break; + case IOV_1V8: + val |= SDVS_1V8; + break; + } + + writel(val, &mmc_base->hctl); +} + +static void omap_hsmmc_set_capabilities(struct mmc *mmc) +{ + struct hsmmc *mmc_base; + struct omap_hsmmc_data *priv = omap_hsmmc_get_data(mmc); + u32 val; + + mmc_base = priv->base_addr; + val = readl(&mmc_base->capa); + + if (priv->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) { + val |= (VS30_3V0SUP | VS18_1V8SUP); + priv->iov = IOV_3V0; + } else if (priv->controller_flags & OMAP_HSMMC_NO_1_8_V) { + val |= VS30_3V0SUP; + val &= ~VS18_1V8SUP; + priv->iov = IOV_3V0; + } else { + val |= VS18_1V8SUP; + val &= ~VS30_3V0SUP; + priv->iov = IOV_1V8; + } + + writel(val, &mmc_base->capa); +} +#endif + static int omap_hsmmc_init_setup(struct mmc *mmc) { struct omap_hsmmc_data *priv = omap_hsmmc_get_data(mmc); @@ -286,9 +343,15 @@ static int omap_hsmmc_init_setup(struct mmc *mmc) if (reg_val & MADMA_EN) priv->controller_flags |= OMAP_HSMMC_USE_ADMA; #endif + +#if CONFIG_IS_ENABLED(DM_MMC) + omap_hsmmc_set_capabilities(mmc); + omap_hsmmc_conf_bus_power(mmc); +#else writel(DTW_1_BITMODE | SDBP_PWROFF | SDVS_3V0, &mmc_base->hctl); writel(readl(&mmc_base->capa) | VS30_3V0SUP | VS18_1V8SUP, &mmc_base->capa); +#endif reg_val = readl(&mmc_base->con) & RESERVED_MASK; @@ -1071,6 +1134,10 @@ static int omap_hsmmc_ofdata_to_platdata(struct udevice *dev) cfg->f_max = fdtdec_get_int(fdt, node, "max-frequency", 52000000); cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195; cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; + if (fdtdec_get_bool(fdt, node, "ti,dual-volt")) + plat->controller_flags |= OMAP_HSMMC_SUPPORTS_DUAL_VOLT; + if (fdtdec_get_bool(fdt, node, "no-1-8-v")) + plat->controller_flags |= OMAP_HSMMC_NO_1_8_V; #ifdef OMAP_HSMMC_USE_GPIO plat->cd_inverted = fdtdec_get_bool(fdt, node, "cd-inverted"); |