keymile: Make distinct kmtegr1, kmvect1, suvd3 configs

The kmtegr1, kmvect1, and suvd3 boards all use the same config include
file with lots of #ifdefs in it.

The Kconfig migation will become easier if we get rid of these #ifdefs
first.

Hence, create distinct config include files for these boards, and unwind
the #ifdef logic in these config files to only include the options
necessary for each board.

Signed-off-by: Mario Six <mario.six@gdsys.cc>

1 files changed, 100 insertions, 0 deletions

diff --git a/include/configs/kmtegr1.h b/include/configs/kmtegr1.h
new file mode 100644
index 0000000000..69397ae5ae
--- /dev/null
+++ b/include/configs/kmtegr1.h
@@ -0,0 +1,100 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ *                    Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ *                    Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ *                    Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+
+/* This needs to be set prior to including km/km83xx-common.h */
+
+#define CONFIG_HOSTNAME   "kmtegr1"
+#define CONFIG_KM_BOARD_NAME   "kmtegr1"
+#define CONFIG_KM_UBI_PARTITION_NAME_BOOT	"ubi0"
+#define CONFIG_KM_UBI_PARTITION_NAME_APP	"ubi1"
+
+#define CONFIG_ENV_ADDR		0xF0100000
+#define CONFIG_ENV_OFFSET	0x100000
+
+#define CONFIG_NAND_ECC_BCH
+#define CONFIG_NAND_KMETER1
+#define CONFIG_SYS_MAX_NAND_DEVICE		1
+#define NAND_MAX_CHIPS				1
+
+/* include common defines/options for all 8309 Keymile boards */
+#include "km/km8309-common.h"
+/* must be after the include because KMBEC_FPGA is otherwise undefined */
+#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
+
+#define CONFIG_SYS_APP1_BASE		0xA0000000
+#define CONFIG_SYS_APP1_SIZE		256 /* Megabytes */
+#define CONFIG_SYS_APP2_BASE		0xB0000000
+#define CONFIG_SYS_APP2_SIZE		256 /* Megabytes */
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * Init Local Bus Memory Controller:
+ *
+ * Bank Bus     Machine PortSz  Size  Device
+ * ---- ---     ------- ------  -----  ------
+ *  2   Local   UPMA    16 bit  256MB APP1
+ *  3   Local   GPCM    16 bit  256MB APP2
+ *
+ */
+
+#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_APP2_BASE | \
+				 BR_PS_16 | \
+				 BR_MS_GPCM | \
+				 BR_V)
+
+#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_APP2_SIZE) | \
+				 OR_GPCM_SCY_5 | \
+				 OR_GPCM_TRLX_CLEAR | \
+				 OR_GPCM_EHTR_CLEAR)
+
+#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_APP2_BASE
+#define CONFIG_SYS_LBLAWAR3_PRELIM	(LBLAWAR_EN | LBLAWAR_256MB)
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT5L (0)
+#define CONFIG_SYS_IBAT5U (0)
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_APP2_BASE | BATL_PP_RW | \
+				 BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_APP2_BASE | BATU_BL_256M | \
+				 BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT6L	(CONFIG_SYS_APP2_BASE | BATL_PP_RW | \
+				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
+
+/* ethernet port connected to piggy (UEC2) */
+#define CONFIG_HAS_ETH1
+#define CONFIG_UEC_ETH2
+#define CONFIG_SYS_UEC2_UCC_NUM		2       /* UCC3 */
+#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK12
+#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR	0
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED	100
+
+#endif /* __CONFIG_H */