powerpc, 5xxx, 512x: remove support for mpc5xxx and mpc512x

There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>

1 files changed, 0 insertions, 300 deletions

diff --git a/include/configs/o2dnt-common.h b/include/configs/o2dnt-common.h
deleted file mode 100644
index 1b4200bcbf..0000000000
--- a/include/configs/o2dnt-common.h
+++ /dev/null
@@ -1,300 +0,0 @@
-/*
- *  Common configuration options for ifm camera boards
- *
- * (C) Copyright 2005
- * Sebastien Cazaux, ifm electronic gmbh
- *
- * (C) Copyright 2012
- * DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __O2D_CONFIG_H
-#define __O2D_CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_MPC5200
-
-#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* running at 33.000000MHz */
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-/* log base 2 of the above value */
-#define CONFIG_SYS_CACHELINE_SHIFT	5
-#endif
-
-/*
-#define CONFIG_POST	(CONFIG_SYS_POST_MEMORY | \
-			 CONFIG_SYS_POST_I2C)
-*/
-
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define MPC5XXX_SRAM_POST_SIZE	(MPC5XXX_SRAM_SIZE - 4)
-#endif
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE	5	/* console is on PSC5 */
-#define CONFIG_SYS_BAUDRATE_TABLE \
-	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-
-#define CONFIG_PCI_MEM_BUS	0x40000000
-#define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE	0x10000000
-
-#define CONFIG_PCI_IO_BUS	0x50000000
-#define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE	0x01000000
-
-#define CONFIG_SYS_XLB_PIPELINING	1
-
-/* Partitions */
-
-#define CONFIG_TIMESTAMP	/* Print image info with timestamp */
-
-#define CONFIG_SYS_ALT_MEMTEST	/* Much more complex memory test */
-
-/*
- * Supported commands
- */
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) || (CONFIG_SYS_TEXT_BASE == 0xFF000000)
-/* Boot low with 16 or 32 MB Flash */
-#define CONFIG_SYS_LOWBOOT	1
-#elif (CONFIG_SYS_TEXT_BASE != 0x00100000)
-#error "CONFIG_SYS_TEXT_BASE value is invalid"
-#endif
-
-
-#define CONFIG_PREBOOT	"run master"
-
-#undef	CONFIG_BOOTARGS
-
-#if !defined(CONSOLE_DEV)
-#define CONSOLE_DEV	"ttyPSC1"
-#endif
-
-/*
- * Default environment for booting old and new kernel versions
- */
-#define CONFIG_IFM_DEFAULT_ENV_OLD					\
-	"flash_self_old=run ramargs addip addmem;"			\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"flash_nfs_old=run nfsargs addip addmem;"			\
-		"bootm ${kernel_addr}\0"				\
-	"net_nfs_old=tftp ${kernel_addr_r} ${bootfile};"		\
-		"run nfsargs addip addmem;"				\
-		"bootm ${kernel_addr_r}\0"
-
-#define CONFIG_IFM_DEFAULT_ENV_NEW					\
-	"fdt_addr_r=900000\0"						\
-	"fdt_file="CONFIG_BOARD_NAME"/"CONFIG_BOARD_NAME".dtb\0"	\
-	"flash_self=run ramargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
-	"flash_nfs=run nfsargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
-	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
-		"tftp ${fdt_addr_r} ${fdt_file}; "			\
-		"run nfsargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
-
-#define	CONFIG_IFM_DEFAULT_ENV_SETTINGS					\
-	"IOpin=0x64\0"							\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addmem=setenv bootargs ${bootargs} ${memlimit}\0"		\
-	"addmisc=sete bootargs ${bootargs} ${miscargs}\0"		\
-	"addtty=sete bootargs ${bootargs} console="			\
-		CONSOLE_DEV ",${baudrate}\0"			\
-	"bootfile="CONFIG_BOARD_NAME"/uImage_"CONFIG_BOARD_NAME"_act\0"	\
-	"kernel_addr_r=600000\0"					\
-	"initrd_high=0x03e00000\0"					\
-	"memlimit=mem="CONFIG_BOARD_MEM_LIMIT"M\0"			\
-	"memtest=mtest 0x00100000 "__stringify(CONFIG_SYS_MEMTEST_END)" 0 1\0" \
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"linuxname="CONFIG_BOARD_NAME"/uImage_"CONFIG_BOARD_NAME"_act\0"\
-	"progLinux=tftp 200000 ${linuxname};erase ${linbot} ${lintop};" \
-		"cp.b ${fileaddr} ${linbot} ${filesize}\0"		\
-	"ramname="CONFIG_BOARD_NAME"/uRamdisk_"CONFIG_BOARD_NAME"_act\0"\
-	"progRam=tftp 200000 ${ramname};erase ${rambot} ${ramtop};"	\
-		"cp.b ${fileaddr} ${rambot} ${filesize}\0"		\
-	"jffname="CONFIG_BOARD_NAME"/uJFFS2_"CONFIG_BOARD_NAME"_act\0"	\
-	"progJff=tftp 200000 ${jffname};erase ${jffbot} ${jfftop};"	\
-		"cp.b ${fileaddr} ${jffbot} ${filesize}\0"		\
-	"rootpath=/opt/eldk/ppc_6xx\0"					\
-	"uboname=" CONFIG_BOARD_NAME					\
-		"/u-boot.bin_" CONFIG_BOARD_NAME "_act\0"		\
-	"progubo=tftp 200000 ${uboname};"				\
-		"protect off ${ubobot} ${ubotop};"			\
-		"erase ${ubobot} ${ubotop};"				\
-		"cp.b ${fileaddr} ${ubobot} ${filesize}\0"		\
-	"unlock=yes\0"							\
-	"post=echo !!! "CONFIG_BOARD_NAME" POWER ON SELF TEST !!!;"	\
-		"setenv bootdelay 1;"					\
-		"crc32 "__stringify(CONFIG_SYS_TEXT_BASE)" "		\
-			BOARD_POST_CRC32_END";"				\
-		"setenv bootcmd "CONFIG_BOARD_BOOTCMD";saveenv;reset\0"
-
-#define CONFIG_BOOTCOMMAND	"run post"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
-
-#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
-/*
- * PCI Bus clocking configuration
- *
- * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
- * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
- */
-#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2	/* define for 66MHz speed */
-#endif
-
-/*
- * There is no write delay with FRAM, write operations are performed at bus
- * speed. Thus, no status polling or write delay is needed.
- */
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_CFI		1
-#define CONFIG_FLASH_CFI_DRIVER		1
-#define CONFIG_FLASH_16BIT
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Write Timeout (in ms) */
-/* Timeout for Flash Clear Lock Bits (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000
-/* "Real" (hardware) sectors protection */
-#define CONFIG_SYS_FLASH_PROTECTION
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SIZE		0x20000
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_OVERWRITE	1
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00040000)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR		0xF0000000
-#define CONFIG_SYS_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR	0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_POST_SIZE
-#else
-/* End of used area in DPRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE
-#endif
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					 GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(192 << 10) /* 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10) /* 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)   /* Initial map for Linux */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT		1
-#endif
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR			0x00
-#define CONFIG_RESET_PHY_R
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPIO_DATADIR		0x00000064 /* PSC1_2, PSC2_1,2 output */
-#define CONFIG_SYS_GPIO_OPENDRAIN	0x00000000 /* No open drain */
-#define CONFIG_SYS_GPIO_DATAVALUE	0x00000000 /* PSC1_1 to 1, rest to 0 */
-#define CONFIG_SYS_GPIO_ENABLE		0x00000064 /* PSC1_2, PSC2_1,2 enable */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#define CONFIG_CMDLINE_EDITING
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
-					 sizeof(CONFIG_SYS_PROMPT) + 16)
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS		16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR		0x100000
-
-/* decrementer freq: 1 ms ticks */
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL		HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_BOARD_EARLY_INIT_R
-
-#define CONFIG_SYS_CS_BURST		0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE		0x33333333
-
-/*
- * DT support
- */
-#define OF_CPU			"PowerPC,5200@0"
-#define OF_SOC			"soc5200@f0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 4)
-
-#endif /* __O2D_CONFIG_H */