diff options
author | Tom Rini <trini@konsulko.com> | 2022-08-02 14:33:31 +0300 |
---|---|---|
committer | Tom Rini <trini@konsulko.com> | 2022-08-21 04:18:15 +0300 |
commit | 5663b137e6827bcced39fb3fcd2e43364bee26c9 (patch) | |
tree | 6e3d2f33403f4a6581328afe2029a3d43359245e /include | |
parent | 30da76be5cbd98581d4290ff744d226fbbe14a04 (diff) | |
download | u-boot-5663b137e6827bcced39fb3fcd2e43364bee26c9.tar.xz |
arm: Remove edminiv2 board
This board is not converted to use CONFIG_DM, well passed the migration
deadline. Remove it.
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Diffstat (limited to 'include')
-rw-r--r-- | include/configs/edminiv2.h | 134 |
1 files changed, 0 insertions, 134 deletions
diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h deleted file mode 100644 index d2f1cd5d5c..0000000000 --- a/include/configs/edminiv2.h +++ /dev/null @@ -1,134 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net> - * - * Based on original Kirkwood support which is - * (C) Copyright 2009 - * Marvell Semiconductor <www.marvell.com> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com> - */ - -#ifndef _CONFIG_EDMINIV2_H -#define _CONFIG_EDMINIV2_H - -/* - * SPL - */ - -#define CONFIG_SYS_UBOOT_BASE 0xfff90000 -#define CONFIG_SYS_UBOOT_START 0x00800000 - -/* - * High Level Configuration Options (easy to change) - */ - -#include <asm/arch/orion5x.h> -/* - * CLKs configurations - */ - -/* - * Board-specific values for Orion5x MPP low level init: - * - MPPs 12 to 15 are SATA LEDs (mode 5) - * - Others are GPIO/unused (mode 3 for MPP0, mode 5 for - * MPP16 to MPP19, mode 0 for others - */ - -#define ORION5X_MPP0_7 0x00000003 -#define ORION5X_MPP8_15 0x55550000 -#define ORION5X_MPP16_23 0x00005555 - -/* - * Board-specific values for Orion5x GPIO low level init: - * - GPIO3 is input (RTC interrupt) - * - GPIO16 is Power LED control (0 = on, 1 = off) - * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16) - * - GPIO18 is Power Button status (0 = Released, 1 = Pressed) - * - GPIO19 is SATA disk power toggle (toggles on 0-to-1) - * - GPIO22 is SATA disk power status () - * - GPIO23 is supply status for SATA disk () - * - GPIO24 is supply control for board (write 1 to power off) - * Last GPIO is 25, further bits are supposed to be 0. - * Enable mask has ones for INPUT, 0 for OUTPUT. - * Default is LED ON, board ON :) - */ - -#define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca -#define ORION5X_GPIO_OUT_VALUE 0x00000000 -#define ORION5X_GPIO_IN_POLARITY 0x000000d0 - -/* - * NS16550 Configuration - */ - -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 } - -/* - * FLASH configuration - */ - -#define CONFIG_SYS_FLASH_BASE 0xfff80000 - -/* auto boot */ - -/* - * Network - */ - -#ifdef CONFIG_CMD_NET -#define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */ -#define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */ -#define CONFIG_PHY_BASE_ADR 0x8 -#endif - -/* - * IDE - */ -#ifdef CONFIG_IDE -#define __io -/* Data, registers and alternate blocks are at the same offset */ -/* Each 8-bit ATA register is aligned to a 4-bytes address */ -/* A single bus, a single device */ -/* ATA registers base is at SATA controller base */ -/* ATA bus 0 is orion5x port 1 on ED Mini V2 */ -/* end of IDE defines */ -#endif /* CMD_IDE */ - -/* - * Common USB/EHCI configuration - */ -#ifdef CONFIG_CMD_USB -#define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE -#endif /* CONFIG_CMD_USB */ - -/* - * I2C related stuff - */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MVTWSI_BASE0 ORION5X_TWSI_BASE -#endif - -/* - * Environment variables configurations - */ - -/* Enable command line editing */ - -/* provide extensive help */ - -/* additions for new relocation code, must be added to all boards */ -#define CONFIG_SYS_SDRAM_BASE 0 - -#endif /* _CONFIG_EDMINIV2_H */ |