diff options
| -rw-r--r-- | board/armltd/vexpress64/Kconfig | 2 | ||||
| -rw-r--r-- | doc/README.semihosting | 2 | ||||
| -rw-r--r-- | include/configs/vexpress_aemv8.h (renamed from include/configs/vexpress_aemv8a.h) | 47 |
3 files changed, 26 insertions, 25 deletions
diff --git a/board/armltd/vexpress64/Kconfig b/board/armltd/vexpress64/Kconfig index 1d13f542e6..4aab3f092e 100644 --- a/board/armltd/vexpress64/Kconfig +++ b/board/armltd/vexpress64/Kconfig @@ -7,7 +7,7 @@ config SYS_VENDOR default "armltd" config SYS_CONFIG_NAME - default "vexpress_aemv8a" + default "vexpress_aemv8" config JUNO_DTB_PART string "NOR flash partition holding DTB" diff --git a/doc/README.semihosting b/doc/README.semihosting index c019999bed..f382d0131e 100644 --- a/doc/README.semihosting +++ b/doc/README.semihosting @@ -25,7 +25,7 @@ or turning on CONFIG_BASE_FVP for the more full featured model. Rather than create a new armv8 board similar to armltd/vexpress64, add semihosting calls to the existing one, enabled with CONFIG_SEMIHOSTING and CONFIG_BASE_FVP both set. Also reuse the existing board config file -vexpress_aemv8a.h but differentiate the two models by the presence or +vexpress_aemv8.h but differentiate the two models by the presence or absence of CONFIG_BASE_FVP. This change is tested and works on both the Foundation and Base fastmodel simulators. diff --git a/include/configs/vexpress_aemv8a.h b/include/configs/vexpress_aemv8.h index 44c746f6f2..52fc15d5fc 100644 --- a/include/configs/vexpress_aemv8a.h +++ b/include/configs/vexpress_aemv8.h @@ -4,36 +4,37 @@ * configurations. */ -#ifndef __VEXPRESS_AEMV8A_H -#define __VEXPRESS_AEMV8A_H +#ifndef __VEXPRESS_AEMV8_H +#define __VEXPRESS_AEMV8_H #define CONFIG_REMAKE_ELF /* Link Definitions */ -#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP +#ifdef CONFIG_TARGET_VEXPRESS64_JUNO +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0) +#else /* ATF loads u-boot here for BASE_FVP model */ #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x03f00000) -#elif CONFIG_TARGET_VEXPRESS64_JUNO -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0) #endif #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ /* CS register bases for the original memory map. */ -#define V2M_PA_CS0 0x00000000 -#define V2M_PA_CS1 0x14000000 -#define V2M_PA_CS2 0x18000000 -#define V2M_PA_CS3 0x1c000000 -#define V2M_PA_CS4 0x0c000000 -#define V2M_PA_CS5 0x10000000 +#define V2M_BASE 0x80000000 +#define V2M_PA_BASE 0x00000000 + +#define V2M_PA_CS0 (V2M_PA_BASE + 0x00000000) +#define V2M_PA_CS1 (V2M_PA_BASE + 0x14000000) +#define V2M_PA_CS2 (V2M_PA_BASE + 0x18000000) +#define V2M_PA_CS3 (V2M_PA_BASE + 0x1c000000) +#define V2M_PA_CS4 (V2M_PA_BASE + 0x0c000000) +#define V2M_PA_CS5 (V2M_PA_BASE + 0x10000000) #define V2M_PERIPH_OFFSET(x) (x << 16) #define V2M_SYSREGS (V2M_PA_CS3 + V2M_PERIPH_OFFSET(1)) #define V2M_SYSCTL (V2M_PA_CS3 + V2M_PERIPH_OFFSET(2)) #define V2M_SERIAL_BUS_PCI (V2M_PA_CS3 + V2M_PERIPH_OFFSET(3)) -#define V2M_BASE 0x80000000 - /* Common peripherals relative to CS7. */ #define V2M_AACI (V2M_PA_CS3 + V2M_PERIPH_OFFSET(4)) #define V2M_MMCI (V2M_PA_CS3 + V2M_PERIPH_OFFSET(5)) @@ -72,23 +73,23 @@ /* Generic Interrupt Controller Definitions */ #ifdef CONFIG_GICV3 -#define GICD_BASE (0x2f000000) -#define GICR_BASE (0x2f100000) +#define GICD_BASE (V2M_PA_BASE + 0x2f000000) +#define GICR_BASE (V2M_PA_BASE + 0x2f100000) #else -#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP -#define GICD_BASE (0x2f000000) -#define GICC_BASE (0x2c000000) -#elif CONFIG_TARGET_VEXPRESS64_JUNO +#ifdef CONFIG_TARGET_VEXPRESS64_JUNO #define GICD_BASE (0x2C010000) #define GICC_BASE (0x2C02f000) +#else +#define GICD_BASE (V2M_PA_BASE + 0x2f000000) +#define GICC_BASE (V2M_PA_BASE + 0x2c000000) #endif #endif /* !CONFIG_GICV3 */ #ifndef CONFIG_TARGET_VEXPRESS64_JUNO /* The Vexpress64 simulators use SMSC91C111 */ #define CONFIG_SMC91111 1 -#define CONFIG_SMC91111_BASE (0x01A000000) +#define CONFIG_SMC91111_BASE (V2M_PA_BASE + 0x01A000000) #endif /* PL011 Serial Configuration */ @@ -113,7 +114,7 @@ #ifdef CONFIG_TARGET_VEXPRESS64_JUNO #define PHYS_SDRAM_2 (0x880000000) #define PHYS_SDRAM_2_SIZE 0x180000000 -#elif CONFIG_TARGET_VEXPRESS64_BASE_FVP && CONFIG_NR_DRAM_BANKS == 2 +#elif CONFIG_NR_DRAM_BANKS == 2 #define PHYS_SDRAM_2 (0x880000000) #define PHYS_SDRAM_2_SIZE 0x80000000 #endif @@ -193,7 +194,7 @@ /* Store environment at top of flash in the same location as blank.img */ /* in the Juno firmware. */ #else -#define CONFIG_SYS_FLASH_BASE 0x0C000000 +#define CONFIG_SYS_FLASH_BASE (V2M_PA_BASE + 0x0C000000) /* 256 x 256KiB sectors */ #define CONFIG_SYS_MAX_FLASH_SECT 256 /* Store environment at top of flash */ @@ -210,4 +211,4 @@ #define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */ #define FLASH_MAX_SECTOR_SIZE 0x00040000 -#endif /* __VEXPRESS_AEMV8A_H */ +#endif /* __VEXPRESS_AEMV8_H */ |